WSS-1 User Manual
Contents
1. 0 c WIRELESS DIGITAL PAN amp TILT SURVEILLANCE SYSTEM USER MANUAL Please read this user manual carefully before using this product ECG wal Packing List 2 4 GHz Wireless Camera 1 2 4 GHz Wireless Receiver 1 Power Adapters 2 AV Cable 1 Earphone 1 2 5 to 3 5mm Earphone Adapter 1 Antenna 1 WSS 1 WSS 2 Camera WSS 3 Receiver WSS 6 Ceiling Wall Camera Mounting Bracket sold seperately oO Q Structure Infrared LEDS CMOS Imaging Sensor Microphone Learning Channel Syni Indicator Power Antenna Plug Indicator Power Switch Rotating Base Learning Channel Sync Channel Selector Power Jack Channel Sync Indicator Earphone Jack second LED Antenna Volume Indicator Volume Control LCD Screen Brightness Control Control Button Zoom Button Channel Button Camera Lens Direction Pad Power Swilch Power Jack A V Output Battery Cover Stand 2 5 to 3 5mm Adapter Included Installation Diagram Camera Power Adapter Power Receiver Monitor TV Adapter s DVR A V Output Receiver also works with 4 AAA Batteries not included Nis A EL wal Installation Attach the antenna to the antenna plug t the back of the camera by HS it in place Then place the camera on a flal stable surface2. Connect one of the provided power adapters to the power jack and then into a power outlet then slide the power switch fo the ey ere The power indicator will light up and the camera will au rate itself by automatically running through its full range of motions Connect one of the Se eae power adapters to the power jack of the receiver and then into 3 power outlet Then slide the power switch to the ON position NOTE This receiver can also work on battery power Please insert four 4 AAA batteries into their appropriate slots at the back of the Note IF will not charge the bateries receiver with proper orientation as indicated on the battery compartment If the receiver is left unused for an extended period of time Nas disconnect it from the power adapter or remove batteries if they have been installed Channel Synchronization for adding additional cameras only Press and hold the Channel button on the receiver until the Learn ing indicator flashes and then press the annn button on the back of the camera while the indicator flashes about 8 seconds on the receiver af which point the channel number displayed on the receiver should match the channel selected on the back of the camera YoU may now control this additional camera with the direction pad on the receiver You may adjust the brightness and the volume to your desired level by rotating the dials on the side of the receiver Volume Control Br
3. etailer Ss PAP for recycling advice NTE Electronics Inc Phone 973 748 5089 e 44 Farrand Street Fax 973 748 6224 S Bloomfield NJ 07003 www nteinc com ECG is a registered trademark of ELECTRONICS INC
4. for a larger clearer picture which can be recorded Specifications Item Value Transmission Frequency ISM 24100 2483 MHz Transmission Power ae 30B Frs Unobstructed Effective Range ENG AN 7 Sele Ssoen aga FESS W Modulation Mode GeSsk a Operating Temperature 3e f eef Operating Humidity IS sears maging Sensor Type S IST Picture 10S Pixels 640 x 480 Minimum tluminaton DER UN Slo IR DE Night Vision Distance Sfr Mind mo View Angle 5e Bandwidth 3MHz ie Sound Detection Sensitivity lt 380B Consumption Current Max S00MA Pewee aia SMDS Dimensions WY gt Fi limemes 441 x 429x 5 24 Weight ORDS LED Seh Wee 23S ii aie B Effective Pixels 480 R O B x 234 a Receiving Sensilfivihy zll Y Consumption Current Max 200mA Battery Working Time 3 hours L Se TT ee SIS TIS Dimensions W x D x H inches SSS S57 x IOS Weight 300S Actual transmission range may vary according to weather location interference or building construction All specifications are subject to minor change without prior notice ECG was WARRANTY 1 Year Waranty This product is warranted to be free from defects in materials and workmanship and meet applicabe specifications when tested to ratings This warranty is in lieu of any other warranty expressed implied or sta
5. ightness Control ECG ua Zooming You tar enlarge the GHE seen on the receiver by two 2 times by pressing the ZOOM button once press again to return to normal viewing mode I Channel Looping Setup The receiver oppen up to 4 cameras working at the same time Press and hold the ZOOM button on the receiver until scanning appears to enable the automatic looping function The channels are shown on the monitor one by one every 5 seconds Press and hold the ZOOM button on the receiver again to exit the looping function You can also press the CHANNEL button to exit the looping function Adjusting Viewing Angle of Camera The direction pad buttons on the receiver act as a remote control for the viewing angle of the camera 1 Use the lt 7 keys to rotate the camera horizontally The maximum angle of rofation is 270 degrees 2 use the a Y keus to rotate the camera vertically The maximum angle of rof tion in this direction is 120 degrees Rotate Image Hold the CTRL button for 3 seconds fo rotate the image seen on the receiver by 180 degrees This optional mode is useful for users who have installed their cameras upside down Other Functions Press the CTRL button once to turn off the LCD screen for sleep mode press if again to turn it back on While in sleep mode you will still be able fo hear the sounds picked up by the microphone You may connect the receiver to any ANAT device with an A V input
6. tutory NTE s liability under this warranty is limited to repairing replacing or issuing credit at the discretion of NTE for such products that become defective or fail to meet specification during the warranty period of one year from the date of sale The technical data shown is intended to provide safe areas of operation for this product Determination as to whether a product is actually defective rests with NTE In no event will NTE be liable for consequential or special damages FCC Information This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 This device does not cause harmful interference 2 This device must accept any interference received including interference that may case undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment Warnings WSS should not be exposed to dripping or splashing liquid No objects filled with liquids shall be placed on the unit Turn off the camera amp receiver if the system is not in use Do not cut the DC power cable of the unit to fit with another power SOUIC e Attention should be given to the environment in regards to battery disposal Environmental Protection Electrical waste products should not be yy disposed of with household waste Please recycle where facilities exist Check with your Local Authority or r
Download Pdf Manuals
Related Search