Lotus Service Notes Section FJ
Contents
1. sp D cyclone indd 1 TRANSMISSION SECTION FJ Introduction Gearchange Mechanism Lubrication Driveshafts Transmission Replacement Transmission Overhaul amp Special Tools See also Toyota transmission repair manual D120T0327J Sub Section FJ 1 FJ 2 FJ 3 FJ 4 FJ 5 FJ 6 Page 2 3 11 12 Page 1 mam 01 04 2005 10 24 54 43 Lous Service Notes SectionFJ FJ 1 INTRODUCTION The transmission assembly is an end on type mounted on the left hand end of the engine unit and comprises of the clutch housing six speed gearbox final drive gears and differential The unit is supplied by Toyota and is designated C64 C series 6 no of gears 4 ratio set with Toyota publication RM930E covering the description and overhaul of this transmission Two control cables are used to transmit the move ment of the gearchange lever to the transmission selector housing running along the centre of the cabin and beneath the power unit The two shaft six speed transmission is housed within a three part casing comprising clutch housing main case and end cover The input shaft is supported by one roller bearing and two separate ball bearings and carries the clutch driven plate the 3rd 4th synchroniser and the 5th 6th synchroniser with the latter housed in the end cover The output shaft is similarly supported by one roller bearing and two ball bearings and carries the 1st 2nd synchroniser and the inte2. Centre Bolt TOOOT 1447 2 Arm x3 TOOOT 1447 3 Adaptor TOOOT 1447 4 5th 6th Synchro Hub Puller Kit TOOOT 1448 comprises Hanger T000T 1448 1 Slide Arm x2 TOOOT 1448 2 Centre Bolt TOOOT 1448 3 Claw no 2 x2 TOOOT 1448 4 Holder TOOOT 1448 5 Output Shaft Seal Replacer Dolly LH T000T1459F Output Shaft Seal Replacer Dolly RH TOOOT Output Shaft Seal Replacer Handle TOOOT 1460F mus Page 12 sn_fj_cyclone indd 12 01 04 2005 10 24 58 Transmission Overhaul Notes 1 Removing and installing 5th and 6th driven gears from the end of the ouput shaft requires considerable force The specified puller tools should be used but when pulling 5th speed driven gear the claws of the tool may require some grinding to allow complete and proper fitment and an anti spreading device is rec ommended to be fitted around the three claws Striking the puller bolt with a hammer in between tightening steps will help shock the gear from its interference fit and engaging two gears to lock the transmission will also aid the process 2 The preload on the differential carrier taper roller bearings is controlled by shims between the bearing outer race and the clutch housing and is determined by installing the final drive assembly in an otherwise empty casing and measuring the steady rotation torque 3 If the input shaft oil seal is to be replaced the bearing should also be renewed since this is likely to be damaged during oil seal removal 4 The rever
3. Inboard joint Circlip m Page 8 sn_fj_cyclone indd 8 D 01 04 2005 10 24 57 na Clicking noises torque reversal clonks or shudder and vibration when accelerating are all possible symp toms of worn C V joints It should not be possible to discern any free play in a joint but care must be taken not to confuse this with transmission backlash which may be considerable Any symptoms that could be due to worn driveshaft joint assemblies should be investigated and rectified without delay since safety considerations are always of paramount importance The inboard C V joint is equipped with a male splined spigot shaft which engages with the female splines of the differential output sun gear with the LH shaft retained by a round section spring circlip on its end and the RH shaft retained by the extension shaft support bearing Each of the two transmission output oil seals runs on a stepped shoulder on the C V joint spigot shaft The stub shaft of each outboard joint is splined into the wheel hub and retained by a nut on the threaded end of the shaft Driveshaft Assembly Replacement Removing a driveshaft assembly from the transmission will result in some loss of transmission lubricant It may be preferred to drain off some oil via the transmission drain plug beforehand 1 Remove the transmission drain plug and drain off approximately 1 litre of oil into a clean container for re use 2 Remove the rear road wheel 3 Remove the spl
4. a new circlip into the end of the housing to retain the joint 10 Fit the gaiter into the grooves on the joint outer body and driveshaft and secure with the new gaiter clips 11 Refit the driveshaft to the car see above Extension Shaft Support Bearing The ball bearing supporting the RH driveshaft extension shaft to the engine block is mounted in a housing which is bolted to a bracket on the engine block The bearing is sealed and maintenance free and is included as part of the inboard C V joint assembly but may if necessary be renewed by the following procedure 1 Remove the RH driveshaft assembly see above 2 Using a press remove the dust shield from the inboard end of the shaft 3 Remove the circlip from the outboard face of the bearing housing and press or pull the housing from the bearing mn Page 10 sn_fj_cyclone indd 10 D 01 04 2005 10 24 57 ne Remove the circlip retaining the bearing and press or pull the bearing from the shaft Press a new bearing into the housing and retain with a new circlip Then use special press tool T000T1438F to press the inner race of the bearing up to the shoulder on the shaft and retain with a new circlip Use special press tool TO00T1439F to press the bearing dust shield onto the shaft and position as shown in the illus tration Press the inboard dust shield onto the end of the shaft to the dimension shown in the illustration Refit the driveshaft to the car se
5. circlip on the end of the left hand inboard joint spigot shaft and lubricate the circlip with grease Also check the condition of the transmission output seal and renew if necessary Lubricate the lip of the seal with transmission oil and grease the corresponding shoulder on the driveshaft C V joint spigot to reduce the danger of damaging the seal on assembly 7 Carefully insert the driveshaft into the transmission with on the left hand shaft the two ends of the circlip positioned lowermost and rotate the shaft if necessary to engage the splines Press the inboard joint outer until a click indicates the engagement of the retaining circlip if necessary using a brass drift and hammer Pull on the body to ensure its security On the right hand shaft fit the bolts securing the extension shaft bearing to the engine mounted bracket and torque to 64 Nm 8 Fit the outer end of the shaft into the hub and refit the top ball joint plinth to the hub carrier with the cam ber adjustment shim pack in position Apply Permabond A130 A912E7033V to the threads of the two socket head bolts and torque to 45 Nm 9 Refit the toe link into the hub carrier and torque the retaining nut to 55 Nm 10 Fit the washer and castellated nut to the driveshaft apply the parking brake and tighten the nut to 220 Nm Fit a new split pin to lock the nut Page 9 wm sn_fj_cyclone indd 9 D 01 04 2005 10 24 57 AB Totus Service Notes SectionFJ 11 Wi
6. driveshaft assemblies are similar but the inboard joint of the right hand shaft is supported in an outrigger bearing bolted to the right hand side of the cylinder block and uses an integral extended shaft to reach into the transmission housing The inboard joints are of a plunging 6 ball double offset design to accommodate driveshaft length variation with suspension travel whereas the outboard joints are high efficiency 8 ball fixed type Replacement outboard joints include the main driveshaft longer on the RH side outboard C V joint and gaiter Replacement inboard joints include the inner C V joint and gaiter kit with the extended stub shaft of the RH joint also including the support bearing and mounting bracket The joints themselves are packed with grease on initial assembly and are maintenance free It is however vitally important that the protective gaiters are carefully inspected at service intervals to check for splits tears or punctures since the joint will deteriorate very quickly once contaminated with dirt or water Damaged gaiters should be renewed immediately once the servicibility of the joint has been established CAUTION The outboard C V joint gaiter can suffer pinch damage if the joint is subjected to extreme articula tion off the car or during driveshaft removal refitment RH Driveshaft Assembly ALLA d W U SAAN Outboard joint Main shaft LH Driveshaft Assembly Outboard joint Main shaft
7. lever pivot ball 11 Fit the new lift tube adaptor onto the gear lever and ensure it is free to slide up and down Hook in the reverse selector cable and secure to the gear lever abutment Temporarily fit the new lift tube onto the adaptor and screw on the new gear knob Adjust the cable to allow correct reverse gear selection and tighten adjuster nuts Remove gear knob and lift tube Clip the selector cable onto the gear lever ball D hole in mounting frame o 1136 12 Cut the tie strap securing the old lift tube in the gear lever gaiter and fit the new lift tube using a suitable tie strap Fit the shroud over the parking brake and gear lever taking care not to scratch the surface finish and aligning the flats on the lift tube with those on the lift tube adaptor Connect the electrical switches as necessary and retain the shroud with the two screws 13 Use the new spring clip to secure the lift tube to the adaptor and fit the new gear knob tightening the grub screw to orientate the graphic correctly Fit and secure the parking brake lever sleeve 14 Check gear selection and reverse inhibit function Ensure the lift tube returns freely under spring action FJ 3 LUBRICATION The transmission should be checked for oil leaks for the correct oil level and the oil renewed at intervals specified in the Maintenance Schedule Transmission oil viscosity SAE 75W 90 Specification API GL 4 or GL 5 Quantity 2 3 litres Transm
8. ained in a housing bolted to the final drive output gear and supported in two taper roller bearings An output extension shaft supported in a ball bearing mounted on the cylinder block is used on the right hand side to allow equal length drive shafts to be used The driveshafts use Rzeppa type joints on their outboard ends and plunging joints at the inboard ends to accommodate the driveshaft length variation concomitant with suspension travel FJ 2 GEARCHANGE MECHANISM The gear lever is spring biased towards the 3rd 4th gear plane and must be moved against light spring pressure to the left before selecting first or second gear or against similar LIFT pressure to the right before selecting Sth or COLLAR 6th speed Engaging Reverse Gear With the vehicle at a complete stand still pause for a moment with the clutch pedal 1 KH fully depressed before moving the lever to the left raising the lift collar beneath the knob and GEAR CHANGE PATTERN then further to the left over a spring detent before finally pushing forwards to engage the gear A two cable mechanism is used to connect the gearchange lever with the transmission one cable shift to transmit the fore aft movement of the lever and a second crossgate cable for the sideways movement The gearchange lever is pivotted at its base and operates the shift cable directly via a ball joint half way up the lever The base of the lever has an extended ball pin on the right hand sid
9. e above FJ 5 TRANSMISSION REPLACEMENT sp D cyclone indd 11 C52593 a AL D NI WH 86 5 0 5mm Prise or pull the bearing dust shield off the shaft f126 1127 The transmission may be removed from below after removing the left hand rear suspension assembly both driveshaft assemblies and the exhaust system Release the clutch release fork gearchange cables earth braid and reverse light switch The engine must be supported to allow the engine and transmission mountings to be disconnected and the power unit tilted as necessary to allow the transmission to be withdrawn The clutch bell housing is secured to the engine by 8 bolts as shown overleaf Page 11 01 04 2005 10 24 57 Clutch housing to engine fixings viewed from gearbox side M12x55 flange head bolts to block 64 Nm M10x65 bolts also secure starter motor 37 Nm M10x55 bolts to block 37 Nm 134 M10x30 bolts to sump 23 Nm FJ 6 TRANSMISSION OVERHAUL The overhauling of the Toyota supplied type C64 transmission is detailed in separate publication D120T0327J Special tools are available through Lotus under the following part numbers Transmission Special Tools Description Lotus Part No Press Dolly driveshaft bearing TOOOT 11438F Press Dolly driveshaft bearing shield TOOOT 1439F Oil Seal Puller TOO0T 1445S Differential Preload Adaptor T000T 1446S 5th 6th Gear Puller Kit T000T 1447 comprises Upper Plate T000T 1447 1
10. e which engages with a crossgate bellcrank lever the other leg of which operates the crossgate cable An inhibit mechanism prevents the gear lever being moved into the reverse gear plane unless a collar beneath the gear knob is lifted The collar is connected by control cable to a pivotted stop arm sprung to an up position In this position a stop pin on the crossgate bellcrank lever abuts against the end of the stop arm and prevents gearlever movement into the reverse gear plane When the collar is lifted the stop arm is pulled down against its spring to clear the stop pin and allow reverse gate selection ohs15a Page 3 wm sn_fj cyclone indd 3 01 04 2005 10 24 55 amp Totus Service Notes SecfonFJ Gearchange Cable Schematic Crossgate Reverse gate Crossgate Crossgate cable release bellcrank lever Shift cable Gear lever P ball pivot Abutment a A P Reverse gate block iii E ee top arm i Transmission External Levers d Shift bellcrank lever A ae o Crossgate cable Inertia a Bez Shift cable R clip clip Transmission cross shaft a housing mn Page 4 sn_fj_cyclone indd 4 D 01 04 2005 10 24 55 The front end of both inner cables are equipped with socket joints which may be clipped on and off the ball pins provided on the gearchange mechanism The outer cables are retained by a forked plastic block bolted into the gearlever handbrake m
11. gral final drive pinion All forward gears are constant mesh with inertia lock type synchromesh with reverse gear attained by sliding a spur idler pinion into engagement with a gear on the periphery of the 1st 2nd synchroniser and a drive gear integral with the input shaft All gears with the exception of reverse use a helical tooth form for quiet running 6th gear 5th gear 4th gear 3rd gear 2nd gear 1st gear Reverse Input shaft eas LP a s a Raab di ZE OT SE WOP ES ce RE E s EL OC kj ig mmn BEM z L e i LIL DOD OP Eg pl SUE poj IRBE TILT 15 b q Oi l E z aa gt A M g HA ir q l l d JE EE Ouput shaft Double cone 2nd Final drive gear gear synchromesh Uk allo w a D u E SE LN 1 Sychromesh For each gear ratio one of the shafts has a fixed gear and meshes with a freely revolving gear on the other shaft To engage a particular gear the freely revolving gear must be connected to its shaft via the sychro hub As an example third gear operates as follows Under normal road driving when the clutch is depressed as a precurser to a gear change the input shaft with the third gear synchroniser are de coupled from the engine but will be turning under inertia clutch windage and oil drag The freely revolving third gear is driven by the fixed gear on the output shaft which itself is driven by the roadwheels Before the outer sleeve of the sync
12. hroniser may be slid on its axial splines to engage with the spline ring integral with third speed input shaft gear the speeds of the two parts must be commonised To aid this process a sychroniser baulk ring is fitted between the two parts being rotationally driven by the synchroniser and equipped with a conical surface to mate with a similar cone integral with the gear Teeth on the outside of the synchro ring over which the synchro sleeve must slide before engaging the third gear splines perform a baulking function described below Page 2 sn_fj_cyclone indd 2 D 01 04 2005 10 24 55 When the gear lever is operated the outer sleeve of the synchroniser is pushed towards third gear and pushes three spring detent plates which press the synchro ring onto the gear cone As the input shaft train is turning faster than third gear the synchro ring is dragged to one end of its rotational constraint slots in the synchroniser in which position the internal spline teeth of the synchroniser sleeve are mis aligned with the teeth on the outside of the synchro ring When further pressure is applied via the gearlever the detent plates are overidden and the synchroniser sleeve splines are pressed against the ends of the sychro ring teeth increas ing the pressure on the conical surfaces The bevelled ends of the sleeve splines and synchro ring teeth tend to turn the ring into alignment but whilst a speed differential between the ring and the gear rema
13. in premature failure If the grease in the joint is contaminated with dirt or water it is likely that the joint is damaged and should be replaced If the grease is not contaminated the joint should be degreased by soaking in a suitable solvent NOT petrol and then carefully inspected Tilt the inner race to one side to expose each ball Severe pitting galling play between ball and its cage window any cracking or damage to the cage or pitting galling or chips in raceways call for joint replacement If the joint is found to be serviceable it must be repacked with the special grease provided Pack the grease into the joint itself and also into the inside of the new gaiter NOTE The grease provided in the kits is specially formulated for wear resistance and durability DO NOT use substitutes or mix with other lubricants The grease specification and quantity also differs for inboard and outboard joints so care must be taken to apply correctly 6 Slide the new outboard gaiter and smaller retaining clip onto the shaft Fit the gaiter into the grooves on the outboard joint body and the driveshaft and secure with the clips provided 8 Slide the new outboard gaiter and retaining clip onto the driveshaft and press the joint inner race onto the driveshaft splines with the match marks aligned if re using joint Retain with a new circlip 9 Fit the inboard joint body to the shaft assembly with the match marks aligned if re using joint and fit
14. ins the cone drag force is dominant and maintains spline mis alignment This is the baulk function When the speed of the input train is synchronised to that of third gear there ceases to be a force dragging the synchro ring to the end of its slots such that the bevelled ends of the splines allow the ring to move back in its slot and for the synchroniser sleeve to be slid over the ring teeth towards the spline teeth on third gear These teeth whose position in relation to those on the synchro ring was entirely at random when speed syn chronisation occurred are now freed to turn under the action of the spline end bevels since there is no longer any pressure applied to the cones The sleeve completes engagement by sliding over the gear spline teeth to connect the synchroniser to the gear In order to cater for the heavy demands made on the second gear synchroniser and provide high durability this gear is fitted with a double cone mechanism to increase the conical surface area within a small space The selector mechanism cross shaft uses Teflon bushes to minimise friction and a mass damper to im prove gearchange feel Aslotted interlock cage allows the selector finger to operate only one selector shaft at atime In order to inhibit the unintended selection of reverse gear a spring detent mechanism is arranged to act on the cross shaft in conjunction with a lift collar at the gearchange lever Aconventional open bevel gear differential is cont
15. ission filler level plug S d To check the oil level Remove the engine bay undertray Wipe clean the area around the socket headed level plug on the front face ofthe transmission main casing Remove the plug and check that the oil is level with the bottom of the hole Note that the release of oil trapped by the plug should not be confused with an indication of correct oil level If necessary add only the specified lubricant see above via the level plug hole until the oil level stabilises at the bottom of the plug hole Alternatively oil may be added into the top of the transmission via a mechanical speedo drive not used in this application cover at the right hand top of the transmission after removing the single screw Page 7 wm sn_fj_cyclone indd 7 01 04 2005 10 24 56 S Refit the level plug with a new sealing washer and tighten securely To renew transmission oil The hexagon headed drain plug located at the bottom of the final drive casing should be removed im mediately after a run when the oil is warm taking suitable precautions against scalding Clean the plug fit a new sealing washer and refit securely Refill to the level plug hole as detailed above FJ 4 DRIVE SHAFTS Each of the two driveshaft assemblies comprises a steel shaft with a constant velocity joint at each end and is used to transmit the drive from each differential output gear to the rear wheel hub The two
16. it pin from the hub nut and remove the nut and washer right hand thread on both sides Before the shaft can be withdrawn from the hub the top ball joint plinth must be released from the hub carrier note camber shims fitted and the toe link ball joint separated from the carrier This will allow the hub carrier to be pulled away sufficiently for the driveshaft to be withdrawn but take care not to strain the brake hose or wheel speed sensor harness 4 LH Driveshaft The left hand driveshaft inboard joint is retained in the transmission by a round section circlip The joint may be removed by applying a shock pull to the C V joint body using a slide hammer with a forked end CAUTION Do NOT attempt to remove the inboard C V joint from the transmission by pulling on the driveshaft The balls of the inboard joint are restrained for transit purposes only by a circlip at the end of the ball tracks Applying an extension force to the joint will damage the balls and require joint replacement Apply pressure only to the outer body of the joint RH Driveshaft The right hand driveshaft incorporates a bearing for the extension shaft and it is this which retains the shaft in the transmission Remove the two bolts securing the bearing bracket and withdraw the complete shaft assembly When withdrawing either splined shaft from the transmission take great care not to damage the ouput oil seal 6 Before re fitting a driveshaft first renew the round section
17. lect B120U0017F 1 Lift Tube Adaptor A120F6259S 1 Spring Clip lift tube to adaptor B120W6770F 1 Knob gear lever M10 C120U0012F 1 Tool gear lever bush guide A120U0054S 1 Procedure 1 Release the grub screw if applicable in the front face of the gear lever knob and unscrew the knob For knobs without grub screws gentle heat may help to soften the thread adhesive Prise off the spring clip from the top of the lift tube adaptor 2 Release the two grub screws in the underside of the parking brake lever sleeve and withdraw the sleeve 3 Remove the two screws securing the front of the gear lever shroud and carefully withdraw the gear park Page 5 wm sn_fj_cyclone indd 5 D 01 04 2005 10 24 56 43 Totus Service Notes SectionFJ brake shroud disconnecting the window switch and hazard lamps switch if applicable Take care to prevent scratching the shroud on seat belt fixings or seat runners 4 Release the reverse selector cable from the gear lever and unhook from the lift tube adaptor Discard the adaptor 5 Prise off the gear selector cable socket from the gear lever use a 10mm spanner 6 From the LH side of the unit remove the screw securing the gear lever pivot to the mounting frame Push the top of the gear lever to the right to help disengage the crossgate selector ball at the bottom of the lever from the bellcrank lever socket Take care not to damage the socket plastic bush which should remain in the bellcrank
18. lever Discard the gear lever 7 To allow fitment of the bush guide tool unhook the main harness from the P clip at the front of the frame temporarily hook over the outside of the shroud fixing leg and rotate the P clip 90 Locate the guide tool in the hole at the RH side of the mounting frame and secure in position using a G clamp as shown but do not crush or distort the frame Bellcrank lever plastic socket G clamp BIN Use suitable bolt to push back socket Special tool A120U0054S Some components omitted for clarity 2 8 Push the plastic socket in the bellcrank lever fully into the guide tool to facilitate installation of the gear lever Apply a dab of mineral oil based lithium grease e g Molykote Longterm W2 to the socket 9 Fit the gear lever feeding the crossgate ball into the bellcrank lever and position the lever upright Using a suitable screwdriver or pry bar push the base of the lever over to the right to engage the crossgate ball into the plastic socket should click home ma Page 6 sn_fj_cyclone indd 6 01 04 2005 10 24 56 AB Lous Service Notes SectionFJ 10 Remove the G clamp and guide tool and push the crossgate socket to the left to engage the D feature on the gearlever pivot ball with the matching hole in the LH side of the frame Apply Permabond A130 A912E6033V to the fixing screw and torque tighten to 10 Nm Restore harness position Sr dd D spigot on
19. m the ball pins on the mechanism levers Release the outer cable plastic abutment block from the mounting frame At the rear end of the cables remove the R clips retaining the inner cable eyes to the levers and the C clips securing the outer cables to the abutment bracket Release the P clips and cable ties as necessary to allow the cables to be withdrawn from the car noting the routing of the cables past the parking brake lever and wiring harness Refit in reverse order to removal paying particular attention to the routing through or alongside the park ing brake lever mounting frame Gearlever Mounting Frame The gear lever parking brake lever mounting frame is secured to thread inserts in the seat mounting cross members by two screws at the front and a single screw at the rear The whole assembly is offset towards the passenger side of the car with alternative fixing holes provided in the crossmembers Gearlever Replacement The gear lever alone may be replaced if necessary using the following procedure Note that fabrication of the gear lever was changed in February 2005 from using a hexagonal section bar to a thicker round section bar the better to resist operator abuse Only the later type will be supplied in service which if being used to replace the hexagonal type will require fitment of the following parts as a set Parts Required Part Number Qty Gear Lever RHD A120F0008S 1 Gear Lever LHD A120F0009S 1 Lift Tube reverse se
20. ounting frame The gear cables are routed along the centre of the cabin floor beneath the fuel tank bay and loop under the engine to an abutment bracket on the top of the transmission housing Both cables are retained in the abutment bracket by spring C clips The shift cable is fitted on the left and uses a bellcrank lever and ball jointed link to connect with the transmission cross shaft lever in order to rotate the shaft The cross shaft lever incorporates an inertia weight to smooth the gearchange action and improve feel The crossgate cable is fitted on the right and uses a centre pivotted lever arm to impart an axial motion to the transmission cross shaft The ends of both inner cables threaded into alloy eyes which are retained on the lever pins by R clips Gearchange Cable Adjustment Under normal circumstances no adjustment to the gear cables should be required If a cable is replaced in service it may be necessary to make minor adjustments via the threaded ball joint at the front of the cable in order to accommodate lever movement within the shroud aperture Gearchange Cable Replacement For access to the gear cables the gear lever shroud and parking brake lever trim must be removed Un screw the gear lever knob remove the single screw each side of the shroud and withdraw the shroud over the gear and parking brake levers Remove the engine bay undertray At the front end of the cables unclip the inner cable ball joint sockets fro
21. se select compression spring shown in the Toyota Repair Manual is not fitted in the Lotus ap plication Page 13 pm sn_fj_cyclone indd 13 01 04 2005 10 24 58 mn Page 14 sn_fj_cyclone indd 14 D 01 04 2005 10 24 58
22. th the car on a level surface top up the transmission oil to the filler level plug hole Driveshaft C V Joint and or Gaiter Replacement The outboard C V joint is supplied complete with main driveshaft to which it is fixed by a spline with a small helix angle to eliminate any potential backlash Separation of the shaft from the joint should not be attempted Note that the RH main shaft is 22mm longer than the LH shaft Replacement of the outboard joint gaiter entails removal of the complete driveshaft assembly from the car and removal of the inboard joint from the shaft 1 Remove the driveshaft assembly from the car see above 2 Remove the clips securing the inboard joint gaiter without damaging the gaiter if it is to be re used Pull the gaiter off the joint outer body remove the circlip in the end of the joint outer body and match mark the body to the joint inner race before sliding the body off the shaft assembly 3 Remove the circlip from the end of the shaft and match mark the inboard joint inner race to the shaft before pulling or pressing the race from the shaft Slide the inboard gaiter off the shaft 4 Remove the clips securing the outboard gaiter and slide the gaiter off the shaft 5 Inspection 8 Cleaning Complete disassembly of either joint is NOT recommended The separate com ponents are a precision fit and develop their own individual wear patterns such that any interchanging or re orientation of parts is likely to result
Download Pdf Manuals
Related Search