Home
New Model Body Repair Information - Techinfo
Contents
1. Rear Bumper Beam Front Bumper Beam Front Fender ROOF PANEL ATTACHMENT The roof rail and roof arch extensions are integrated into the roof panel assembly The roof panel bolts and spot welds must be removed and installed to the inner pillar and roof rail structure using a specific procedure Refer to the body repair manual section titled Roof Panel Removal and Installation for complete information Front Roof Rail Extension RoofArch A 4 Bolts 2 Bolts 3 Bolts Rear Roof Rail 3 of 15 NEW DOOR STRUCTURE The doors on this vehicle use new technology to join steel and aluminum panels e This is the world s first application of this technology to a door panel e Door panel weight is reduced by approximately EE Aluminum 17 percent compared to all steel doors improving vehicle handling and fuel economy E Steel e The inner door panel is a conventional steel structure e The outer door panel is made of aluminum alloy The two panels are joined using adhesive and a special 3D lock seam joint e The outer door panels are not serviced separately e Minor damage to aluminum door panels may be repaired by Conventional body shops that have a dedicated aluminum repair facility Stoel Steel and tools e Major damage to the aluminum door panels may require Spot weiding 1 fold homming 2 foid n ata door replacement REAR WHEEL ARCH HEM JOINT To improve styling and tire clearance a hemme
2. in the gauge control module e The TPMS indicator will stay on and the system will set DTCs if all four tire pressure sensor IDs are not memorized by the TPMS control unit after you replace a wheel and or tire pressure sensor e Refer to Memorizing a Tire Pressure Sensor ID in the service Low Tire Pressure TPMS Indicator manual for complete information e The HDS or equivalent scan tool may be required to perform this memorization Contact an Acura dealer for assistance if necessary PRECISION ALL WHEEL STEER SYSTEM Some models are equipped with the Precision All Wheel Steer System e The Precision All Wheel Steer P AWS monitors and adjusts the rear toe angles to help maximize handling and stability under all conditions e An electric actuator with a toe position sensor is installed at each rear wheel between the steering knuckle and subframe e The neutral position of the toe sensors must be relearned using the HDS scan tool if the control unit or either actuator is replaced e Refer to Rear Toe Position Sensor Neutral Position Memorize in the service manual for complete information Precision All Wheel Steer Actuator as ELECTRIC PARKING BRAKE a ETE All models are equipped with an electric parking brake a e Electric actuators on each rear brake caliper apply and release the brake pads e A manual procedure is provided if a malfunction prevents parking brake release e Refer to Electric Parking Brake For
3. not followed The ACC warning message may also appear Lane Keeping Assist System LKAS System The LKAS camera must be aimed if The camera control unit is removed or replaced The windshield is removed or replaced The amber LKAS indicator comes on and blinks if the aiming is not done or is not completed The LKAS warning message may also appear Windshield Replacement On FOW LDW LKAS Equipped Vehicles ELECTRICAL GROUND WIRE PROTECTION Windshield damage within the FOW LDW LKAS camera s field of vision can cause any these systems to operate abnormally Only a genuine Acura replacement windshield should be installed Installing an aftermarket replacement windshield may also cause abnormal operation Painting over electrical ground locations may cause electrical systems such as Vehicle Stability Assist VSA to malfunction and set DTCs that may be j difficult to diagnose GROUND BO Protect the ground wire and the ground wire mounting hole threads with a bolt or plug when priming or painting Adaptive Cruise Control Problem Lane Keeping Assist Problem _ GROUND WFE aoe MOUNTING HOLI RLX Sport Hybrid SH AWD Information RLX SPORT HYBRID SH AWD MODEL IDENTIFICATION e Available nationwide Hub il e Unique grille and LED turn indicators and fog lamps e HYBRID badges on the front fenders n DS SH AWD badge on the trunk lid SS ST RY AT e Orange high voltage cables under the hood Sport Hybrid SH
4. system parts e When making airbag system repairs only use new genuine replacement parts which are manufactured to the same standards and quality as the original parts e To ensure the correct replacement airbag system parts are installed provide the vehicle s VIN when ordering parts Compare the part numbers on the new and removed parts to make sure they match AIRBAG SYSTEM ELECTRICAL REPAIRS Except when doing electrical inspections that require battery power always place the vehicle in the OFF LOCK mode disconnect the negative battery cable then wait at least 3 minutes before starting work e For easier identification electrical connectors that contain only airbag system wiring are yellow in color e Many harnesses that contain primarily airbag wiring are also wrapped in yellow tape e Airbag system wiring that runs through a common harness such as a floor harness is generally not marked e NEVER attempt to modify splice or repair airbag system wiring If airbag system wiring is damaged replace the wiring harness es NOTE Refer to the service manual for complete restraint system operation diagnostic and repair information 10 of 15 Electrical Repair Information TIRE PRESSURE MONITORING SYSTEM TPMS This vehicle is equipped with an initiator tyoe TPMS e The low tire pressure TPMS indicator comes on if the air pressure is too low in one or more tires TPMS messages will also appear on the multi information display
5. AWD Identification Badges RLX SPORT HYBRID SH AWD MODEL DIFFERENCES The following systems are unique or significantly different from regular RLX models Refer to the service manual for complete information on these systems If needed contact an Acura dealer for repair assistance Power System Indicator The gauge module includes a new Power System indicator e This Indicator illuminates when faults occur in the high voltage components of the vehicle e Comes on when the High Voltage battery temperature becomes high while the battery is being charged e Checking DTCs requires an HDS or equivalent scan tool Contact an Acura dealer for assistance if necessary Power System Indicator Electric Servo Brake System An electric servo brake system is used to provide traditional brake system feel during electric operation It also coordinates electric motor regeneration and the vehicle s brakes for seamless deceleration and stopping e Brake system components appear significantly different than traditional brake systems e The amber BRAKE SYSTEM indicator comes in the event of an electric servo brake system malfunction e Special brake fluid replacement and bleeding procedures are required Contact an Acura dealer for Brake Operating Simulator assistance if necessary Electric Servo Brake System Brake System Indicator Cooling and HVAC Systems Cooling system differences include e Separate engine and elec
6. MODEL YEAR DATE OF ISSUE BULLETIN NUMBER MODELE ANNEE DATE EN VIGUEUR NUMERO DU BULLETIN AACURA secs 2014 MAY 14 2014 BRN 14 6 Body Repair News RLX HYBRID 2014 RLX amp SPORT HYBRID SH AWD New Model Body Repair Information DISCLAIMER This publication contains a summary of new body and vehicle technology that may affect collision and other body repairs Always refer to the appropriate service and body repair manuals for complete repair information A subscription may be purchased at techinfo acura com TABLE OF CONTENTS New Model Body Technology Body Repair Information Welding Precautions and Information Airbag System Components and Repairs Electrical Repair Information RLX Sport Hybrid SH AWD Information OVERVIEW OF BODY FEATURES Next Generation Advanced Compatibility Engineering ACE body structure Body construction using 55 high tensile strength steel including 20 in grades 780 980 and 1 500 MPa Extensive aluminum components for weight reduction and improved fuel efficiency not shown in this view Aluminum hybrid front and rear door construction not shown in this view Hem style rear wheel arch panel joint oe ae o 2014 Honda Canada Inc All Rights Reserved 1 of 15 New Model Body Technology BODY CONSTRUCTION AND HIGH STRENGTH STEEL CONTENT e Steel parts are color coded based on their tensile strength in megapascals MPa e High strength steel is defined as any steel with a
7. S Indicator When you turn the vehicle to the ON mode this indicator should come on and then turn off after about 6 seconds e Ifthe SRS indicator does not go off or does not come on at all there is a problem with the system e DTCs must be read and cleared using the HDS or equivalent scan tool Contact an Acura dealer for assistance if necessary e Ifa vehicle is sent to the dealer for airbag system repair or troubleshooting include a copy of the repair estimate with part numbers and the source for any replaced airbag system parts SRS Indicator Passenger Airbag OFF Indicator The indicator comes on to alert you that the passengers front airbag has been turned off e This occurs when the front passenger s weight sensors detect 65 lb 29 kg or less the weight of an infant or small child on the seat e lf the indicator comes on with no front passenger and no objects on the seat or with an adult occupying the seat something may be interfering with the seat weight sensors or there may be a problem with the system Contact an Acura dealer for assistance if necessary Passenger Airbag OFF Indicator AIRBAG SYSTEM REPAIRS REQUIRED AFTER DEPLOYMENT To restore proper function and allow DTCs to be cleared the airbag system MUST be repaired as specified in the service manual Refer to Component Replacement Inspection After Deployment for complete information e DO NOT install used refurbished or modified airbag
8. TC has been cleared using the HDS or equivalent scan tool Contact an Acura dealer for assistance if necessary CDS Signal Output SRS Unit Collision Power Shutdown System Diagram 14 of 15 ADDITIONAL BRACING AND HIGH STRENGTH STEEL LOCATIONS e The body includes additional bolt in braces to accommodate the high voltage battery and drive components e The front pillar center pillar and front floor assemblies contain additional 590 and 980 MPa stiffeners e Always refer to the correct parts catalog when ordering replacement structural parts sport Hybrid SH AWD Model Examples of Additional Bracing amp High Strength Steel locations E Additional Bracing amp High Strength Steel ELECTRIC POWERTRAIN SYSTEM The electric powertrain system uses a lithium ion battery in and intelligent power unit IPU located behind the rear seat High voltage circuits route power to the engine compartment The high voltage system operates at up to approximately 260 volts High Voltage Cables e High voltage is identified using bright AIG Compressor x orange colored cables and coverings pa e A damaged high voltage lithium ion battery j i can emit toxic fumes and the organic solvent i AN 1 used as electrolyte is flammable and Cle High Voltage Battery Fuel Tank corrosive Always wear protective equipment e High temperatures may damage the Wi high voltage battery module e For example when drying pain
9. ain airbags mounted above the side windows under the headliner SMARTVENT SIDE AIRBAGS This vehicle is equipped with SmartVent side airbag construction e This airbag design helps mitigate the risk of excessive airbag deployment force and risk of injury to smaller front passenger seat occupants e Eliminates the need for the Occupant Position Detection System OPDS sensor located in the front passenger s seatback As with all side airbags the following service precautions apply e Special seat covers and or breakaway thread are used to ensure proper deployment path e Damaged front seat covers should be replaced not repaired High Pressure Area e Do not install non factory seat covers because they may alter the airbag s intended deployment path Low Pressure Area Divider and Vent Holes smartVent Side Airbag DRIVER S KNEE AIRBAG The driver s knee SRS airbag helps keep the driver in the proper position and to help maximize the benefit provided by the vehicle s other safety features e The driver s knee SRS airbag is mounted to the steering hanger beam below the steering column e It is designed to inflate in a moderate to severe frontal collision e Normally it inflates with the driver s front airbag but may also inflate alone under certain conditions Driver s Knee Airbag 9 of 15 AIRBAG SYSTEM INDICATORS There are two indicators used for the airbag system Supplemental Restraint System SR
10. amage improper repairs or excessive foreign material on any of the following e Rear bumper e Outer side panels e Radar unit mounting locations Several checks and inspections must be done during repairs to the radar unit mounting area If the mounting area check is not done an Acura dealer may not be able to properly aim the radar units For more information refer to BSI Radar Unit Mounting Area Check in the service manual Heating Unacceptable a NY uy STIFFENERS Do Not Section Cut and joint BSI Alert Indicator LH BSI Unit Mounting Area Check 6 of 15 Welding Precautions and Information REPAIRING 1 500 MPa STEEL PARTS Observe these precautions when repairing 1 500 MPa steel parts e NEVER attempt to straighten damaged 1 500 MPa steel parts because they may crack e 1 500 MPa steel parts MUST be replaced at factory seams using squeeze type resistance spot welding STRSW e MIG brazed joints should be used ONLY in locations not accessible by a spot welder e To assure adequate weld tensile strength always set the spot welder to the specifications provided in the body repair manual Important Information Parts made of Ultra High Strength Steel UHSS 1 500MPa USIBOR must be installed as a complete part No sectioning allowed Ultra High Strength Steel requires special welding equipment procedures and settings See the welding section of the appropriate body repair manual Fai
11. ced Cancellation in the service manual Electric Parking Brake Caliper SYSTEMS THAT MAY REQUIRE DEALER ASSISTANCE WITH AIMING Some models may be equipped with one or more of the following systems that require aiming after collision repairs Special tools are required to complete the aiming procedures Contact an Acura dealer for assistance Blind Spot Information BSI System The BSI radar unit must be aimed in these instances e After replacing or removal and installation of one or both BSI radar units e After replacing repairing the body rear outer side panel s e Stored DTCs B18B8 or B1E68 left or right side BSI radar unit azimuth off alignment If a problem occurs in the BSI system the amber BSI indicator BSI Indicator will illuminate and this warning message may also appear Blind Spot Info System Problem Forward Collision Warning and Lane Departure Warning FCW LDW The FOW LDW camera must be re aimed if e The FOW LDW camera unit is removed or replaced e The windshield is removed or replaced If the aiming is incomplete the FCW and LDW indicators come on and blink Adaptive Cruise Control ACC and Collision Mitigating Braking System CMBS The millimeter wave radar for the ACC and CMBS must be re aimed if The radar unit is removed or replaced The radar unit s mounting area was damaged The amber ACC indicator comes on if the aiming process is not completed or the service manual procedure is
12. d rear wheel arch joint is used e The outer and inner rear panels are joined using adhesive in the wheel opening area e The outer panel is then rolled and crimped over the inner panel similar to a door panel crimp e Other vehicle manufacturers have previously used this technology so rolling and flanging tools are commercially available e fthe above tools are not available instructions are provided in the body repair manual to make the set of hemming pliers necessary to complete this joint e Refer to the body repair manual section titled Rear Side Outer Panel Removal and Installation for complete information Rear Wheel Arch Hem Joint Area mm Inner Panel gees Outer Panel m Adhesive Dust Sealer Before Hemming After Hemming Rear WheelArch Section A A 4 of 15 STEERING HANGER BEAM The steering hanger beam provides mounting for the steering column and dashboard components e The beam is constructed from aluminum for weight savings e Do not repair the steering hanger beam if it is damaged e Special threaded collar bolts are used on the passenger side of the beam to compensate for any variation in body dimensions e A specific installation and bolt tightening procedure is required e Refer to Dashboard Steering Hanger Beam Removal and Installation in the service manual for complete information Aluminum Steering Hanger Beam ACOUSTIC SIDE DOOR GLASS Acoustic front side door glass is used for sou
13. lure to use the proper equipment or follow the proper procedures can result in an unsafe repair e NEVER perform MAG welding on 1 500 MPa steel The heat generated during welding will significantly reduce the strength and structural integrity of 1 500 MPa steel parts e This photo shows tensile strength test results of welded 1 500 MPa steel The 1 500 MPa steel fractured first because the welding heat reduced its strength to far below 590 MPa e For more information refer to Hot Stamp 1 500 MPa Parts Welding Specifications in the body repair manual Tensile Test Results of Welded 1 500 MPa Steel MIG BRAZING GUIDELINES FOR 1 500 MPa STEEL PARTS Refer to the body repair manual for complete information MIG brazed joint locations are specified in the ee li body repair manual a Asingle or double hole MIG braze may be on specified in the body repair manual depending on the tensile strength of the parts being joined e The size and number of holes are critical to O achieving adequate joint strength Pulsed MIG OK e A pulsed MIG welder MUST be used Refer to the equipment manufacturer s instructions for welder voltage and current setup e Photos at right show the difference in results between pulsed and non pulsed MIG brazing a 7 of 15 MAG WELDING SPECIFICATIONS FOR 590 980 MPa HIGH STRENGTH STEEL PARTS NOTE In this publication and the body repair manuals gas metal arc welding GMAW is
14. nd isolation on some trim levels e The glass has a sound insulation layer of PVB polyvinyl butyral sandwiched between two layers of semi tempered glass e Acoustic side glass is thinner than conventional side glass e This type of glass is similar to laminated windshield glass It does not shatter like conventional side window glass e To ensure the correct replacement glass is installed provide the vehicle s VIN when ordering parts Semi tempered Glass Sound Insulation Interlayer t5 mm t4 mm Semi tempered Glass section A A Comparison Of Conventional amp Acoustic Side Door Glass CAPLESS FUEL FILLER This vehicle uses a capless fuel filler design It does not have a conventional gas cap e If you need to refuel the vehicle from a portable fuel container a funnel is provided in the trunk tool case e For more information refer to Refueling From a Portable Fuel Container in the owner s manual TOWING AND LIFTING PRECAUTIONS e All models must be towed using flat bed towing equipment only or the vehicle s drive system will be damaged e Do not lift or tow this vehicle by its bumpers or serious damage will result e For more information refer to Lift and Support Points in the appropriate service or body repair manual 5 of 15 Body Repair Information NOTE The following content is intended only to highlight new special concerns No body repairs should be attempted without first referenci
15. ng the appropriate body repair manual for complete information USE OF HEAT DURING BODY STRAIGHTENING AND REPAIR C When you are doing body straightening and repair procedures UN DO NOT apply heat to any body part during straightening This may compromise the internal structure and strength of high strength steel parts Any part that has heat applied to it during straightening MUST be replaced with new parts Ignoring these instructions may significantly reduce occupant protection in any subsequent collision SECTIONING CUT AND JOINT GUIDELINES Because of body structure improvements for collision safety and rigidity the materials steel thickness and internal reinforcements have become very specific Follow these guidelines to avoid an unsafe repair Avoid sectioning cut and joint except for outer panels and floor panels unless a specific procedure is provided in the body repair manual Replace body structural components as assemblies that match the replacement parts configuration Refer to Front Side Frame and Rear Frame Cutting and Splicing in the body repair manual for sectioning opportunities BLIND SPOT INFORMATION BSI SYSTEM Models equipped with this system can be identified by this BSI Alert Indicator located on both front doors near the outside rearview mirror The system uses two radar units mounted on each side of the vehicle under the rear bumper The system may malfunction and set DTCs because of d
16. o move it there is a car wash mode To enter car wash mode e Push and hold the neutral button for more than 5 seconds e While continuing to hold the neutral button push the Engine Start Stop button e The vehicle will now remain in neutral with the ignition in the accessory position Electronic Gear Selector Acoustic Vehicle Alerting System AVAS The vehicle makes a low volume sound to alert pedestrians when the vehicle is Acoustic Vehicle propelled solely by electricity and approaching at a speed of about 12 mph 20 km h or less Alerting System e The system consists of a AVAS control unit and speaker Problem e The system cannot be turned off on US models e The warning message shown here will display if an AVAS problem is detected Collision Power Shutdown System The electric powertrain system is equipped with a system to shut off the high voltage circuits in the event of a collision e When the SRS unit detects a collision it sends collision Battery Condition information to the battery condition monitor module via Monitor Module a hardwired crash detection signal CDS output e Ifthe battery condition monitor module judges that the CDS signal meets a programmed threshold the high voltage contactors are shut off for safety anda DTC P1D65 Is set e Check the high voltage battery and cables for damage and replace any damaged components e After repairs are completed the vehicle will not restart until the D
17. referred to by its subtypes depending on the welding brazing requirements e MIG welding brazing Metal inert gas welding or brazing where 100 argon Ar shielding gas is used Argon is inert and does not react with the molten weld pool or brazing operation e MAG welding Metal active gas welding where the shielding gas being used contains a mixture of 80 argon Ar and 20 carbon dioxide CO It is considered active because the CO undergoes a limited reaction with the molten weld pool Important Information Parts made of High Strength Steel 590 980 MPa must be installed as a complete part No sectioning is allowed unless a procedure is provided in the body repair manual This high strength steel requires special welding equipment procedures and settings See the welding section of the appropriate body repair manual Failure to use the proper equipment or follow the proper procedures can result in an unsafe repair The body repair manual specifies the weld types and Steel Tensile MPa Wire Tensile ksi locations for each body panel e The welding wire used must have a tensile strength equal 990 286 to or greater than the lowest tensile strength of the parts 780 being welded This conversion chart shows the relationship of steel tensile strength MPa to the minimum welding wire 980 tensile strength ksi 7 e Typical ER70S 6 MIG wire has a minimum tensile strength OM pel RSI of 70 ksi 483 MPa It can be used
18. t in a heated paint booth the temperature must 12V Battery Fuse Box Ni E not exceed 150 F 65 C Electric Motor Fuel Lines EER es and Generator Power Drive Unit Motor Drive Unit Improper high voltage handling or service may High Voltage Component amp Cable Layout Cause serious injury such as electrocution e Service or repair of the electric powertrain system should be done only by properly trained technicians Contact an Acura dealer for assistance if necessary e Follow high voltage safety precautions when working on or around the electric powertrain system Isolate the high voltage before doing any welding or electrical repairs e Refer to Electric Powertrain System in the body repair manual or Electric Powertrain Service Precautions in the service manual for complete information e Additional high voltage safety information may be found in the Emergency Response Guide for each model These are available free of charge on the Acura ServiceExpress website ADDITIONAL SPORT HYBRID SH AWD TOWING AND LIFTING PRECAUTIONS e When rolling a damaged Sport Hybrid SH AWD model with any of the wheels on the ground the electric motor can produce electricity and remains a potential source of electric shock even when the high voltage system is turned off e Sport Hybrid SH AWD models do not have a manual switch to disable the system Whenever service work requires spinning the front or rear wheels with the engine alwa
19. tensile strength of 340 MPa or higher e Steel repair and welding procedures vary depending on the tensile strength of the parts involved 270 MPa 590 MPa Important Information These illustrations are for general reference only Some body parts are constructed from multiple layers of different tensile strength steels Always refer to the body repair manual body construction section for Steel Tensile Strength Legend specific steel tensile strength information 1 500 MPa HOT STAMP STEEL LOCATIONS 1 500 MPa steel is stronger than ordinary steel so it can help protect vehicle occupants while reducing overall vehicle weight to improve fuel efficiency The numbered parts in the diagrams below are constructed of 1 500 MPa steel All Models Front Inner Upper Pillar as Front Pillar Upper Stiffener Roof Side Stiffener Center Pillar Upper Stiffener Side Sill Stiffener a A WwW N 2 of 15 ALUMINUM PARTS amp REPAIRABILITY All of the parts shown below are constructed of aluminum alloy Repairability Issues e Do not repair the front subframe or bumper beams if damaged e Aluminum body panels may be repaired by body shops that have a dedicated aluminum repair facilities and tools e To prevent galvanic corrosion some fasteners for aluminum parts are considered one time use and must be replaced if removed Front Subframe ss gt Tunnel Floor BarA Steering Hanger Beam in ge gt
20. tric power plant EPP cooling systems e Several electric coolant pumps are used to circulate coolant when the gasoline engine is not running e Special coolant fill procedures are required during component replacement HVAC system differences include e High voltage electric A C compressor Electric Power Plant EPP Cooling System 13 of 15 Special Head Up Display Windshield A head up display system provides the driver an expanded view of vehicle operating parameters projected onto the windshield e The windshield is specially laminated to project the HUD image and must be replaced with a HUD windshield e fan incorrect windshield is installed a double image will be projected e The windshield part number is marked on the upper left edge of the glass e To ensure the correct replacement glass is installed provide the vehicle s VIN when ordering parts Head Up Display Windshield Marking Location Electronic Gear Selection System An electronic gear selection system uses shift selector buttons to replace the transmission shifter and cable e The Electronic Gear Selection control unit has a programmed door open park logic When park is not selected and the vehicle is stopped if the driver s seat belt is unbuckled and the driver s door is opened the vehicle will shift into park automatically to prevent a roll away e lf the vehicle needs to be placed into neutral with the engine off such when pushing t
21. when welding up to 440 MPa steel parts Refer to the diagrams shown below MAG Plug Welds MAG Butt Welds 980 MPa Steel 590 MPa Steel 590 MPa Steel 590 MPa Steel Welding Wire Tensile Strength Must Be Welding Wire Tensile Strength Must Be 2590 MPa 286 ksi 2590 MPa 286 ksi MAG PLUG WELDING GUIDELINES e MAG plug welding may be done when joining body components to 590 980 MPa steel parts e Follow the recommendations described in the body repair manual section MAG welding specifications for high strength steel parts 590 MPa and higher MAG Plug Welding MAG BUTT WELDING GUIDELINES e MAG butt welding may be done only on steel parts with a tensile strength of 590 MPa and lower e Welding speed is critical to achieve the correct weld strength and minimize the heat affected zone HAZ e Follow the recommendations described in the body repair manual section MAG welding specifications for high strength steel parts 590 MPa and higher MAG Butt Welding 8 of 15 Airbag System Components and Repairs AIRBAG SYSTEM COMPONENTS The airbag system in this vehicle includes the following components that may deploy ina collision 1 Driver and front passenger seat belt tensioners may deploy independently from any airbags 2 Driver and front passenger SRS airbags 3 Driver s knee SRS airbag 4 Side airbags mounted in the outer driver and front passenger seat backs 5 Left and right side curt
22. ys lift and support the vehicle so all four wheels are off the ground e For more information refer to Emergency Towing in the owner s manual 15 of 15
Download Pdf Manuals
Related Search
Related Contents
EFI Proof Paper ZP 80 (Premium Newspaper) Samsung GT-S5830I Εγχειρίδιο χρήσης Copyright © All rights reserved.
Failed to retrieve file