Screamin` Eagle Extreme Billet Air Cleaner - Harley
Contents
1. that the ignition key switch is in the OFF position before installing the main fuse 1 Install the main fuse See the service manual NOTES Install the rain sock over the air filter element in wet or rainy conditions to prevent water intrusion Install the pre charger 13 over the air filter element under these circumstances Recalibrate ECM NOTICE You must recalibrate the ECM when installing this kit Failure to properly recalibrate the ECM can result in severe engine damage 00399b Have a Harley Davidson dealer install the new ECM calibration using Digital Technician Air Filter Element Maintenance 1 Inspect the air filter element every 5000 miles 8000 km or more often under dusty conditions NOTES e The use of cleaning drying or oiling methods or products other than those shown damages the filter and void the manufacturer s warranty e K amp N Air filter Cleaner is available from a Harley Davidson dealer either alone 1 qt 0 95 L sprayer bottle Part No J06102 99883 88T Or a 12 fl 0z 0 35 L sprayer bottle as part of the Filter Care Service Kit Part No 99850 92T K amp N Air Filter Oil is also available from a Harley Davidson dealer either alone 12 25 02 347 gram aerosol can Part No 99882 88T Or a 6 5 02 184 gram aerosol can as part of the Filter Care Service Kit DO NOT OVER OIL THE AIR FILTER Over oiling can interfere with the proper performance of the engine and or certain engi2. cMOTOR HARLEY DAVIDSON WY J06102 INSTRUCTIONS REV 2014 07 30 SCREAMIN EAGLE PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 29400220 29400221 Models For model fitment information see the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only Installation Requirements Proper installation of this kit requires the use of Digital Techni cian by a factory trained technician at a Harley Davidson dealer This kit requires the use of Loctite 243 Threadlocker and Sealant Blue Part No 99642 97 and is available from a Harley Davidson dealer AWARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation One is available from a Harley Davidson dealer Kit Contents See Figure 1 and Table 1 NOTE The kit is intended for High Performance applications only Engine related performance parts are intended FOR THE EXPERIENCED RIDER ONLY This engine related performance part is legal for sale or use in California on pollutio
3. e the adhesive side onto the backplate Align to the equally spaced screw holes and position the gasket carefully before firmly pressing the gasket into place 3 Apply Loctite 243 blue to breather screw threads and mating tapped holes in cylinder head 4 Insert new breather screws 5 through the backplate 5 Install screws into the cylinder head but do not tighten 6 Install air cleaner mounting screws 4 through the mounting bracket 6 and into the backplate 2 until the screw threads are captured in induction module Leave fasteners loose 7 Alternately tighten two breather screws 5 to 120 144 in Ibs 13 6 16 3 Nm 8 Tighten three air cleaner screws 4 to 55 60 in Ibs 6 2 6 8 Nm 9 FL Touring models Install fuel tank per service manual instructions 1 of 3 Please dispose of materials responsibly Install air cleaner filter and cover NOTE Whenever the air cleaner cover is installed apply Loctite 243 blue to the air cleaner cover screw 8 1 See Figure 1 Install the air cleaner element 7 air filter screen 11 and cover 9 Before tightening the center screw align the cover using the medallion for best appearance Tighten center screw to 36 60 in Ibs 4 1 6 8 Nm NOTE Apply a small amount of dish soap to medallion O ring to aid in installation of medallion 2 Install the medallion into the center hole by pressing in place Do not damage the O ring Completion NOTE Verify
4. filter media Allow to absorb 2of3 SERVICE PARTS is07256a Figure 1 Service Parts Screamin Eagle Performance Air Cleaner Kit Table 1 Service Parts Item Description Quantity Part Number 1 O ring 2 113 4 11292 2 Backplate chrome Kit 29400123 29000080 Backplate black Kit 29400124 29000079 3 Gasket throttle body 29241 08 4 Screw socket head cap 1 4 20 x 1 75 in 44 5 mm long 3 Not sold separately 5 Bolt breather 2 29400081 6 Bracket mounting 29400072 7 Air filter element 29400065 8 Screw hex socket flat head 5 16 18 x 2 0 in 51 mm long Not sold separately 9 Cover air cleaner Not sold separately 10 Medallion Screamin Eagle 14100367 11 Screen air filter chrome Kit 29400221 29400082 Screen air filter black Kit 29400220 29400100 12 O ring medallion 11170 13 Pre charger 29400121 Items mentioned in text but not included in kit A Induction module bracket J06102 3of3
5. n controlled motor vehicles The Product Information Label contained in this kit is a requirement of the California Air Resource Board CARB emission regulation Place the label on the right side of the frame directly beneath the VIN sticker This label is not required outside the state of California Installation of this kit by an authorized Harley Davidson dealer will not impact your limited vehicle warranty J06102 Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled REMOVAL IWAN IN To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b 1 Remove main fuse Refer to the service manual 2 FLTouring models Remove the fuel tank per the service manual 3 Remove and recycle or properly dispose of the currently installed air cleaner Refer to the service manual or the instructions 4 See Figure 1 and Table 1 Remove and recycle or properly dispose of the induction module support bracket A INSTALLATION Install Air Cleaner NOTE When servicing the air cleaner apply Loctite 243 blue to all fasteners 1 See Figure 1 Install two O rings 1 from kit in grooves around breather screw holes on induction module side of backplate assembly 2 Install two O rings 1 from kit in grooves in underside of head of breather screws 5 2 Peel the protective strip off the gasket 3 and plac
6. ne components If oil is still draining or dripping from the filter media 20 minutes after oiling clean and oil the filter element again To clean the element a Remove the center medallion by inserting a small flat blade screwdriver in the slot at the bottom of the medallion Carefully work around the center portion without scratching the finish of the air cleaner cover Rotating the medallion aids in removal b Remove the air cleaner cover center screw c Tap the element to dislodge any loose dirt Gently brush with a soft bristle brush d Spray air filter cleaner liberally onto the cotton filter media and let soak for ten minutes Or roll and soak the cotton filter media in a shallow pan of air filter cleaner Remove immediately and let soak for ten minutes e Rinse off the filter media flowing from the clean side to the dirty side with low pressure tap water f After rinsing shake off all excess water and let the filter media air dry DO NOT use compressed air or a heat gun to speed drying g After the filter media is dry EITHER spray air filter oil along each pleat once only holding the spray nozzle approximately 3 in 76 mm away from the media Or carefully use a squeeze bottle to deposit oil along each pleat once only Let the oil absorb into the filter media for 20 minutes before proceeding After 20 minutes inspect the filter media Carefully apply oil to any remaining visible white spots on the
Download Pdf Manuals
Related Search