Home
Service Manual
Contents
1. Figure 2 30 Working principle of wheel side reducer 1 Internal gear ring 2 Planetary carrier 3 Half axle 4 Planetary gears 5 Wheel hub 6 Solar gear Solar gear is connected with half axle by spline Internal gear ring is fixed on the wheel side supporting axis which on two ends of driving axle shell Planetary gears mesh with solar gear and internal gear ring The planetary gears are installed on the planetary gear carrier by steel balls and planetary gear axis Planetary gear carriers are fixed with hub as one part by bolts So planetary gear carriers and hub rotate together For improving the meshing condition between solar gear and planetary gears and distributing the meshing load equally half axle is not fixed to keep in condition of floating state 4 Driving axle principle of driving axle From the main internal structure of driving axle shown in the Figure 2 1 it is known that The left and right shells of the differential mechanism are connected by bolts The driven spiral bevel gear of the main driving axle is fixed on the flange edge of the differential right shell by bolts Axle journals of the cross axis embed in the holes which are formed by the relevant groove which on the joint face between left and right shells One planetary gear is floating installed on the journal of cross axis Both of the gear and cross axis mesh with the two straight tooth conical half axle gears The journals of the two half axle gears install on th
2. Half axle gt Solar gear Planetary gears Planetary carrier Hub assembly gt Driving wheels Service Manual Driving Axle CHAPTER HUI DISASSEMBLY OF DRIVING AXLE 3 1 Network Figure of General Disassembly corresponding to disassembly of driving axle Brake pliers assembly Make bracket assembly to up Fix driving axle assembly on i ie PERE E 7 oa Tnternal l 3 naeg T i unnn 1 4 4 M T i Rolling 14 K bearing Neha yA fmb ld Y assembly ON i Sleeve 16 y gasket i Main transmission assembly li 13 Service Manual Driving Axle Disassembly Tools and Equipments Application position Name of general corresponding to the No of tools epecricalon Aumper Network Figure or assembly name oe MI16 MI17 MI18 oe Choose different specification 58 MI2000P Sroup by size of screws ET 13 16 17 18 21 24 TN Choose different specification 30 34 41 50 a by size of screws During hanging flick the firm l parts by it Flick bearings when disassembly them Name of special tools Application position corresponding to the No of Network Figure or assembly name Aceecablyeannicror Prepare to provide your AA eeeie own assembly platform i when without it Shield ring pliers for When Disassembling the one for each axis hole shield ring Round nuts special 12 tools Replace it by common Screw pusher bolts according to size
3. I After disassembly the standard criterion of the parts scraped Whether completely lose their function service performance and could not be repaired II There has two ways to judge the disassembled parts 1 watch amp touch by hand 2 measure the dimension I Judge the disassembled parts by watching and touching primarily make sure replace the parts when under the following condition 1 Never further use those parts with seriously knocked fracture crack or looseness function 2 Because of low reliability and short service life resulted in repeated reuse Never further use oil seals dust ring o ring and gasket after disassembling by reason of leakage 3 Never further use bolts nuts washers plug screws pipe joints if there is serious corrosion and the screw could not wring well in tightening operation or the screw is damaged worn out or slipping 4 Never further use the looseness proof wire for bolts connection after disassembling 5 Never further use those bearings if they could not be turned smoothly by hand or the crack exists the ball race 1s seriously worn or the balls are broken 6 Never further use those gears and splines if there have cracks sheet exfoliation collision or over wearing appears on the teeth 7 Never further use those shells with crack those mounting holes on the bearing shell with crack serious wear or sheet exfoliation and those shell screws damaged result in operating weakly in ti
4. adjustment of contact area Make sure be carried out seriously Notice After adjustment clean up the red lead powder 53 Service Manual Driving Axle 3 3 6 Install the locking tablet Tighten the fixing bolt of the bearing seat the tightening torque is 5 00 600 Nm Place the locking tablet rightly then fix the locking tablet on the bearing seat with bolts and the washer and tighten the fixing bolt of the locking tablet kgm Tightening torque 40 50 Nm 500 600 Nm Notice Coat suitable 1262 screw lock fixing sealant within the 5 10 mm length from the screw end of the fixing bolt of the locking tablet a 1262 screw lock fixing sealant 3 3 7 Install the stop push bolt Turnover the bracket press the copper sleeve in the end of the stop push bolt then screw them in the bracket let the copper sleeve contact with the back of the driven spiral bevel gear in the differential mechanism Then turn 1 6 1 4 circle and tighten with the nut and locking tablet Fold bending one tooth of the locking tablet to avoid the nut loosing Then tighten the fixed bolts of the seal cover korn Tightening torque of the nut M14 55 125 165Nm M12 55 78 104Nm Notice Tighten the fixed bolts of the seal cover should be according to the symmetric cross method in order 54 Service Manual Driving Axle Chapter V Standard Criterions of Maintenance and Parts Replacement for the Axle
5. thickness reference 1 2 1 4 generally 2 0 for spiral bevel gear 1 2 tooth of circle 2 0 028 50 028 65 Recommend 0 3T less lower limit Recommend 0 3T more than upper limit than
6. G a i SISS Sss a bevel gear solar wheel frame ATI HAN VI PN 7 Seale uN o x ae i GY a oil N B Gl Fe o a EEE T x i F ai lee z Aila j Z PS Ji ae AASA Au R Z 9 half shaft Z r Pl Ai wo OROI ah yyw INNS ae iE tH ts A im s in SSS zal half shaft gear Hp aN s Gd POPPY l y i ee VIE LICL PLEO WK amp Sas IT solar gear gt E EA II at A OU Is 7 gt S A C O AS zim a N aa K i A Kd O steel ball tee sy Qh J Z HIH p A ER Iy L gh solar gear shaft CZAD QA cross solar halfshaft driven helix adjust ventilated brake oil sear inner gear shaft bevel gear bevel gear bevel wheel nut _ pipe disc seals cover Figure 2 1 2 4 Working Principle of the Driving Axle Driving axle assembly function of increasing torque reducing speed and differencing speed are carried out by differential mechanism and wheel side reducer Its working principle is introduced as follow 1 Working principle of differential mechanism Maotion Characteristic The symmetrical bevel gear differential mechanism used in driving axle assembly is a kind of planetary gear mechanism The planetary is composed with differential gear shell and cross shaft both of which are connected together At the same time the differential gear shell is driving part because it connects with following spiral bevel gear it is assumed that the angle speeds of the differential gear shell and two
7. MOBIL Auto gear oil Thuban EP HD85W 140 10 50 C HD80W 90 Domestic oil The similar foreign oil brands brands MOBIL CALTEX CASTROL ESSO SHELL 2 or 3 lithium MOBIL Marfak Ronex MP Energrease Retinax A based grease grease multi LM grease Beacon EP L Alvania GB7324 1994 XHP222 Purpose 2 It s suitable to be used to seal the pipe thread of Hydraulic system and pneumatic system or be used on the surface with little oil l It s used to fix and seal the M 10 M 20 screws and the 1262 pipe thread fixed sealant l A i ones are endured intense vibration and impact oroa lithium based wrease It s suitable to be used to lubricate the fiction position grease rolling bearing and sliding bearing of any kinds of GB 7324 1994 engineering machinery between 20 120 C It s used to clean the surface of metals and enhance the 1755 cleaning agent adhesion strength between repair agent pope thread fixed sealant and substrate 1545 oxygen weary type pipe thread sealant Sealant Cleaning agent Service Manual Driving Axle 1 3 Marker For communication and memory those following marks are used in important safety and quality Marker Item Remark Specially take care of the safety during the operation Notice Pay attention to the technical requirements and make sure the operations reach the requirements in operation Parts and their heavy and disassembling methods Make sure choose the appropriat
8. in the holes Pay attention to whether the hands would be extruded at holding position when assemble parts by hand directly 11 The disassembled parts need to be checked The parts which have poor properties should be changed and the standard of criterion can be found in chapter V Standard of criterion for repairing and replacing the parts of the axle 12 There should be no interference after assembling each part 13 Protection measures must be taken when the oil seal and seal ring across key seats screw holes and steps when assembling oil seal and seal ring to avoid damaging the oil seal and seal ring 14 To avoid damaging the screw fasteners all the tools must be suitable to the screw fasteners when assembling the parts 15 Never use the gas trigger when tighten the screws Make sure tighten them by hand to special degree and then tighten them with some specification wrest wrenches to reach the torque demanded 16 When removing oil in the axle Make sure loosen the releasing screw off slowly to avoid the oil blowout Service Manual Driving Axle 1 2 Oil and Coating Materials Kinematic The similar foreign oil brands Be classified by the U A API GL 5 Viscosity Domestic oil brands 100 C mm s MOBIL CALTEX ESSO SHELL Mobilube 1 SHC synthetic oil Heavyduty MOBIL Auto gear oil Multi Spirax EP u motor Auto oil HD80W 90 Gear oil GX Heavyduty 85w 90 GL 5 133724 0 20 40 C Purpose Dii GB13895 1992
9. side half axle gears are wo revolution per minute is no and revolutions per minute are n and n2 then the following equations will be right 2M0 01 Oo 2no n n2 These equations are the motion characteristic equations of symmetrical bevel gear differential Service Manual Driving Axle mechanism with two same diameter half axle gears They show that the sum speed of left and right half axle gears is same as two times of the speed of differential gear shell but is not relation with the speed of planetary gears So when the loader turns or drives on other conditions the planetary gears can rotate themselves on their corresponding speed to make the wheels on two sides rotate in different speed but not slide The up equations show that When the speed of one side half axle is zero the speed of the other side is two times of the differential gear shell In the condition that the speed of differential gear shell is zero when one side half axle is rotated by external power the other side will reverse rotate in the same speed 2 Working principle of differential mechanism Torque Distribution Assumption The torque from main reducer to symmetrical bevel gear differential mechanism is Mo inside and outside of half axle torques which are distributed by the differential gear are M and M3 internal friction torque of differential gear is M M gt M1 Mo M gt M M The following conclusions will be drawn from the previous
10. the reading is within 45 75N Finally coat the Coat 1262 screw lock fix sealant on the thread hole of the inner gear installed the screw from the second tooth to the fifth or sixth pitches form a liquid level on the 1 3 circle of the screw then tighten the screw and fix the round nut 2 Before measuring the pressure make sure rotate the hub for more than five times forward and backward 35 Service Manual Driving Axle fo N1262 screw lock fix sealant kg Tightening torque of the screw 40 50 Nm 7 Install the O shape sealing ring Install the O shape sealing ring on the planet gear frame assembly 8 Assemble the planet gear frame assembly dE ae a BI a DETEN Install the planet gear frame assembly and O shape sealing ring on the hub with the rim bolts gaskets and nuts Tightening torque 500 560Nm C o The planet gear frame assembly 9 Install plugs Wring plugs with glues in the oil holes at the both wheel side co 1545 oxygen weary type pipe threads sealant korn Tightening torque 70 100 Nm 10 Refueling Refuel SL SAE85W 90 GL 5 gear oil GB13895 1992 in each two wheel side reducer Refuel 3L for each in this process finally load 2L for each again 36 Service Manual Driving Axle AL GS AE85W 90 GL 5 Gear oil 11 Install the brake Place the end surface of the axle shell upward horizontally Install the disk brake at the opposite sid
11. 680 850 825 1100 1120 1400 1160 1546 s aso amos 991095 BS T 10452259 15595207 952 1293 1759 oss 640 1269 1723 2345 2259 3012 2923 3898 1400 1700 2473 109 900 1650 2000 3298 2800 3350 4111 S481 1606 2181 5068 129 1080 ee ne eee 3812 5082 4933 6577 Remark The tightening torque of joint bolts can be executed referred this previous table during the assembling operation When the tightening torque given in the chapter IV is not accord with the table it should be executed according with the tightening torque given in the chapter IV Service Manual Driving Axle CHAPTER II CONSTRUCTION AND WORKING PRINCIPLE OF THE DRIVING AXLE 2 1 Outside View 1 Wheel side reducer assembly 2 Brake clip assembly 3 Main driving axle 4 Input flange 5 Deflations tap screw hole 6 Refueling plug 7 Axle shell 8 Wheel hub assembly 9 End cover 10 Oil discharging plug Service Manual Driving Axle 2 2 General View A b Le i I P wa LA f J alt i 366 5 zal Ch th Base parameters of driving axle Spiral Bevel Gear First order Main Driving Deceleration axle Reduction Ratio 5 286 Type First order Planetary Deceleration Wheel side Reducer Reduction Ratio SAE85W 90 GL 5 2 3 The Internal Construction of Driving Axle Driving axle assembly is one of the most important parts in driving axle system The main functions of driving axle are lowering the rota
12. Coat the lubricating oil when install the bevel gear and the bevel gear gasket a Lubricating oil 3 2 4 Install the differential mechanism shell Install the cross assembly in the right shell of the differential mechanism and let bevel gear mesh with the half axis gear Turnover the differential mechanism left shell assembly and install it with the differential mechanism right shell assembly then joint the left and right shell of the differential mechanism with bolts and tighten with washers and nuts Tightening torque of the nut 305 25 Nm Notice 1 Make sure the assembly mark on the right 47 Service Manual Driving Axle shell of the differential mechanism aligns to the left shell of the differential mechanism 2 Coat the suitable 1262 screw lock fixing sealant within the 10mm length from the screw bottom of the bolt af 1262 screw lock fixing sealant 3 The half axis gear and the bevel gear can rotate flexibly by hand and have no jam after assembling 3 2 5 Install the driven spiral bevel gear Align the assembly mark fasten the driven spiral bevel gear front axle is left lateral and back axle is right lateral on the right shell of the differential mechanism with the bolt washer and nut then tighten the nut korn Tightening torque of the nut 305425 Nm 1 Coat the suitable 1262 screw lock fixing sealant within the 10 mm length from the screw bottom of the bolt 1262 s
13. G nunai R 9 CHAPTER HI DISASSEMBLY OF DRIVING AXLE eeeeeesssssssssssssssssssrereeeeessssssssssssssosorrrreeessess 13 3 1 Network Figure of Total Disassembling corresponding to disassembly of driving axle 13 32 Disassembly OE drivin axl Earner a EOT T 15 zo Disassomb inr OL ASSCIMDIICS a oc tanec eel caus E E ain E T E 19 3 3 1 Disassemble planetary wheel carrier assembly cc cccccccccsssssssseessseeeeeeeceeeeeeees 19 3 3 2 Disassemble the hub assembly 0000nnnnonnnnnnnnnnnnnnssssssssssssserrreeeesssssssssssssssssseeereeeeses 20 3 3 3 Disassemble main driving axle assembly ccccccccccccccceceeeeeeceeeeseesesseeeeeeeeeeeeeees 22 3 3 4 Disassemble the differential mechanism assembly ccccccccssssssssseseseeeeeeeeeeeeees 25 3 3 9 Disassemble the active spiral bevel assembly sc 2 4oc tigers Dede et aeons 2T Chapter IV the Assemb yor DIVOS AX Een a E A een baat aaa 29 4 1 The Network Figure of the General Assembly 00 0 cceececccseeeeeeceeeeeeeeeeeessessseeeeeeeeeeeeeees 29 4 2 Specification of Assembly of Axle and Notices ccccccssceeeeececeeeeeeeeeeeeeeesssssseeeeeeeeeeees 31 4 2 1 Classifications and tightening methods of screw fasteners of the axle 0 31 ADD NOUCES 1 ASSEN INO AKC icc ssis cherries E ds anaeean gee wiensaeauneeaenenetooes 32 ADAY AKG AN SGCMIDILY er O EN 34 4 4 Partial Assembling of the Assembly lt sssssssessiexsvcsacdsacastseas adusedavessvnests
14. Service Manual _ _ _ ST Wheel Loader Driving Axle Applicable Range Driving Axle of LG956 LG953 LG952 Series Wheel Loaders SHANDONG LINGONG CONSTRUCTION MACHINERY CO LTD Service Manual Driving Axle ST Wheel Loader Driving Axle Service Manual 880x1230 mm 16 4 pieces Ist Edition and 1st Print in Sep 2008 SHANDONG LINGONG CONSTRUCTION MACHINERY CO LTD Address Linyi Economic Development Zone 276023 Tel 86 539 8785597 Fax 86 539 8785618 Website www sdlg cn Service Manual Driving Axle Service Manual Concise Guide All reasonable steps have been taken to ensure that this publication is correct and complete but should any user be in doubt about any detail clarification may be sought from Shandong Lingong construction machinery Co Ltd or their accredited representative The information in this document is subject to change without notice and should not be construed as commitment by Shandong Lingong construction machinery Co Ltd Shandong Lingong construction machinery Co Ltd accepts no responsibility for any errors that may appear in this document Shandong Lingong construction machinery Co Ltd P R China All rights reserved The contents of this publication may not be reproduced in any form or communicated to a third part without prior written permission of Shandong Lingong construction machinery Co Ltd Shandong Lingong construction machinery Co Ltd Linyi Economi
15. c Development Zone Linyi 276023 Shandong Province P R China Tel 86 539 8785597 Fax 86 539 8785618 Email service sdlg cn Website http www sdlg cn Service Manual Driving Axle PREFACE This service manual which shows the structure principle and the maintenance technology of the driving axle will help the maintenance persons understand the disassemble and assemble method of the driving axle more deeply and bring the maintenance workers solid technology basis of locating faults and maintaining correctly Please read the manual carefully to make full use of it completely Main contents of the Service Manual include 1 Structure and working principle of the driving axle This chapter shows the structures and functions of each kind of part it is not only the basis of assembling and disassembling axles but also can be used as the reference of locating faults 2 Disassembly of the driving axle The steps how to disassemble the parts correctly and the points for attention in disassembling driving axle are shown in this chapter 3 Assembly of the driving axle The steps how to assemble the parts correctly and the points for attention in driving axle are shown in this chapter 4 Standard criterion of the driving axle for repairing and replacement The identification methods and standard criterions of consumable parts after worn are prescribed in this chapter Special notes This service manual is described as examp
16. crew lock fixing sealant 2 The judgment methods of the left and right lateral Face to the front of the gear the helical teeth extends from smaller end to bigger end according to clockwise named right lateral On the contrary extend from smaller end to bigger end according to anticlockwise named left lateral 3 2 6 Install the bearing Install rolling bearing on the external end bearing of right shell of the differential mechanism 48 Service Manual Driving Axle Install rolling bearing on the external end bearing of left shell of the differential mechanism 3 3 1 Install the active spiral bevel gear Measure the dimension size of L shown in the Figure The original selection thickness of recommended adjusting gasket is equal to the measured value subtracts 55 5 Fix the bracket on the assembly frame with the smaller end upward Coat the sealant on the smaller end surface and install the adjusting gasket Install the active spiral bevel gear assembly after assembling in the bracket 49 Service Manual Driving Axle 3 3 2 Assemble the seal cover Press the oil seal in the seal cover i Notice Coat suitable lubricating oil on the external p diameter when assemble the oil seal S aid Lubricating oil 3 3 3 Install the input flange Put the gasket on the end surface of the bracket then assemble the seal cover assembly Coat lubricating grease according to the general requirement
17. e extinguishing equipments are necessary and smoking is forbidden in the region except the smoking room 3 When welding operation is needed it should be done by expert workers who were trained by professional welding training Welding gloves baffles goggles hats and other work clothes suitable for welding are essential during welding operation 4 Before the driving axle assembly is disassembled the appearance of which must be cleared up to avoid the parts been polluted in the disassembling operation 5 Make sure wear safety boots helmets and working clothes coincided with requirements when operating Goggles should be worn when workers knock the parts with copper rod 6 The disassembled parts could be cleaned by petrol gasoline and water base oil cleaner l Service Manual Driving Axle 7 Check the spreaders whether were broken before operate the cranes and other hoisting equipments Make sure use the sufficient hanging up capacity of the spreader For avoiding collisions between parts spreaders should been operated slowly and located in the correct region Make sure no one work under the part lifted 8 When two or more persons operating together the operation procedures abided by all persons should be made before operating for avoiding the accidence caused by out of steps 9 All tools should be kept carefully and be familiar with their usages 10 When align two holes the workers make sure their hands and figures are not
18. e left and right base holes on the differential Service Manual Driving Axle shell and connect with half axle by splines The half axle is a solid shaft between differential mechanism and wheel side reducer Its inside end connects with half axle gear by splines and its outside end connects with shield ring and solar gear of wheel side reducer by splines The left and right half axles of loader are full floating structure Two ends of half axle bear torque mainly because of the kind of structure For avoiding half axle motions along axis the end which connects with wheel side reducer solar gear is positive stop by steel balls The torque and speed are transmitted to half axle by differential mechanism And then they will be transmitted to wheel side reducer by half axle Solar gear connects with half axle by spline Internal gear ring is fixed on the two ends wheel side bearing shafts of driving axle shell by splines They are fixed and can not be moved The planetary gear which meshes with solar gear and internal gear ring is installed on the planetary carrier by steel balls and planetary gear axis Planetary carrier and hub are connected by hub bolts So planetary carrier and hub will rotate together Driving axle way will be drawn from the above structure Driving axle power Driving axle shaft Input flange Driving spiral bevel gear Driven spiral bevel gear Left and right shells of differential mechanism gt Half axle gear
19. e of the axle belly on the braking clamp rack and then fix with the bolt and washer Tightening torque 376 502Nm C ro Brake 12 Refueling Refuel 17L SAE85W 90 GL 5 gear oil GB13895 1992 in the axle packet of the axle shell A GB SAE85W 90 GL S gear oil 13 Assemble the main drive assembly 13 1 Coat 1596 silicone rubber plane sealant on the joint surface between the axle shell and the bracket Coat the sealant which diameter is 3 6 circled closed ring on the bigger end surface of the axle shell and the internal side of the thread hole Coat this sealant on the thread holes at the both sides of R40 Arc Never place the sealant in the air for more than 10 minutes N 1596 silicone rubber plane sealant a7 Service Manual Driving Axle 13 2 Install the main driving Hoist the main drive assembly with the joist barrow Install the final driver in the final driver shell of the axle and then install the locating pin C ro The main drive assembly 13 3 Install bolts Coat proper 1262 screw lock fixing sealant on the bolts and the coating position is the 15mm length from the end of the screw And then fasten the main drive assembly and the axle shell assembly with bolts and washers l Tightening torque 193 257Nm Z lt 1262 screw lock fixing sealant Notice Fasten each bolt according to the symmetric cross method 14 Install the sun gear Install the sun gear o
20. e spreader and the operating posture Tightening Pay more attention to the parts Tightening Torque in assembly Torque operation The location where need to be coated with adhesives and greases a il and n pane Inject required volume of lubricating oil water or fuel oil The place of oil expulsion and water draining or the emission Outpour volume 1 4 Hoisting Explanation 1 When it is not easy to assemble the parts from drive axle assembly check the following Check that whether all of fixing bolts are removed on the disassembled parts Check whether some other parts interfered disassembling are laid on the removed parts 2 Wire Ropes 1 Wire rope should be in the middle of the hook If it is in one end of the hook the wire rope may drop from hook and that may cause serious accidence The biggest strength is in the middle of the hook shown in Figure 1 1 2 Never use one single wire rope Make sure use two or more ropes winding bind on the hoisting heavy Service Manual Driving Axle I 100 88 T9 T1 41 Figure 1 1 AN Hoisting with one wire rope may cause the heavy rotates and then the wire rope looses or the heavy slides from the fixed location which will cause serious accidence 3 The hoisting angle between wire rope and hook should not be oversize when hoist the extremely heavy loading When the hook hoists heavy loading with two or more ropes the bigger of angle between wire
21. ease use other Cleaning Please use other Machine methods without it press Please use other methods without it Pe eens 0 02 0 200 Caliper Inter hexagonal wrench ne Select different specification according Wrest wrench 0 350Nm 1 group 0 800Nm to the size of the assembly bolts Run out measuring instrument Pull tensile 0 300 0 100N irop 6 partial assemble the active spiral dynamometer bevel gear assembly Using Position corresponding to the Specification Number serial number of network chart or assembly parts name Daviea Prepare assembly asenbins ie support yourself l without it pe g i i iaar Assemble the circlip Special tool for round nut a es co Gils __ a group when sling te oil ea l l l l l Install the input flange Special Tools Name o 30 Service Manual Driving Axle 4 2 Specification of Assembly of Axle and Notices 4 2 1 Classifications and tightening methods of screw fasteners of the axle According to the analysis of the request of assembly performances processes operations and quality as well as factors such as prevention for oil leakage and importance of quality characteristic in assembling for the axle s serial production the screw fasteners of the axle are classified into three grades A B and C Table for screw fasteners in grade A of the driving axle Bolts for the wheel side end cover Connecting bolts and nuts for shells on both side of t
22. embly to avoid hurting internal parts during the hanging operation 3 3 Disassembly of assemblies 3 3 1 Disassemble planetary wheel carrier assembly 1 Put planetary carrier on working table horizontally 2 Knock the planetary wheel carrier out lightly by the copper bar 3 Take down the steel balls Service Manual Driving Axle 4 Take down the planetary gears and gasket 5 Disassemble the shield ring firstly And then take down the noodle roller on the internal wall of planetary gears 3 3 2 Disassemble the hub assembly 1 Put hub assembly on working table horizontally 2 Loose off the bolts connecting brake plate and hub with corresponding specification tools 20 Service Manual Driving Axle 3 Take down the brake plate 4 Loose off the screws connecting oil seal end cover and hub with corresponding specification Take down oil seal end cover 5 Take down gasket 6 Take down frame oil seal 21 Service Manual Driving Axle 7 Take bearing out 3 3 3 Disassemble main driving axle assembly l Pace and fixed the main driving axle on the carrier input flange upward horizontally 2 Loose locking nuts off with corresponding specification Take down the input flange and gasket 3 Loose off the bolts connecting seal cover and bearing sleeve by corresponding specifications tool and take the seal cover down 22 Service Manual D
23. ent on the component must be cleaned out There must be no corrosion scratch or damage on the mating surface and friction surface The oil holes and groove should be clean and unobstructed 2 During assembling never damage the screw parts on bolts 3 The head of bolts and end face of nuts should be uniform contacted with the fastened parts Make sure neither inclination nor hammering makes the faces to contact and ensure no bending deformation of the screws 4 The fastener should be under uniform compression make sure closely joint and connect firmly 5 It is forbidden to use inappropriate wrench and sleeve when tightening the screws and nuts 6 Assemble using fastener parts strictly according to the right grade as mentioned Never use low 32 Service Manual Driving Axle performance fastener instead of high performance ones or Never use high performance fastener instead of low performance ones 7 Coat little sealant for locking screws on the external thread cycle by cycle Never coat onto the first two pitches of the screw Make sure the width of sealant coated with 3 to 5 pitches then wring the internal screw till to the specification torque When the internal hole is a blind hole coat some sealant onto bottom of the hole and then tighten 8 When assembling the screws and bolts make sure wring them by more than 2 3 pitches and then preload with tools and finally tighten to specification torque with corresponding spec
24. equations When the torques from left and right half axle are different the difference value of them works on the planetary gears and overcome the internal friction torque of differential gear to drive the planetary gears This makes the differential action 2 When the speeds of left and right half axle are different torques on them are different too Torque on the slower axle is bigger and that on the faster axle 1s smaller 3 The sum torque on two half axles is the same as the one on differential gear Because the friction torque of the popular symmetrical bevel gear differential mechanism is very small it can be considered as that the torque is distributed equally whether the speeds of left and right wheel are same This is the driving axle characteristic the same torque but the different speed of common differential mechanism This characteristic is suitable for loader when operates and drives on the common condition But under the wicked condition the passing capacity will be affected seriously 3 Working principle of the wheel side reducer Wheel side reducer is the last increasing torque and reducing speed mechanism It is a kind of planetary driving axle mechanism It is made up of solar gear fixed gear ring driven planetary carrier and planetary gears Working principle is shown as Figure 2 30 This Figure is not complete the same as the actual structure and is just the principle introduction 10 Service Manual Driving Axle
25. er E y ra H l Folling bearing Y a er A _ Skeleton oil seal o T 4 i H End cover of eal the oil seal lt lt T EH p Ky l i Brake disk k gt Gasket j Bolt washer 1 1 Install the external ring of the bearing 32221 with the bigger end of the hub upward Then turn over install the external ring of the bearing 32024 with the smaller end of the hub upward and install the internal ring of the bearing 32024 1 2 Coat the lubricating oil on the end cover of the oil seal and check the integrality of the oil seal Coat uniformly the lubricating oil in the groove of the skeleton oil seal and then install the skeleton oil seal in the end cover of the oil seal 41 Service Manual Driving Axle 1 3 Install the gasket on the smaller end surface of the hub then install the end cover of the oil seal on the smaller end of hub and tighten with the bolt M8 45 and washer k on i Tightening torque 22 25 Nm Notice Fasten each bolt according to the symmetric cross method 1 4 Install the brake disc on the hub then tighten with the bolts M20 1 5 50 and the washer Tightening torque 280 380Nm C r9 Brake disc Notice Fasten every bolt according to the symmetric cross method 42 Service Manual Driving Axle Planet gear i cult INS 2 Install the pl t f bl a NSS are iL i Insta e planet gear frame assembly savas ool ee cia eis Steel ball SSIS Shield t
26. f spiral bevel gear is no less than 50 along with the tooth depth and tooth length directions the imprint of the driven spiral bevel gear is near to the centre and be found on the middle of tooth depth along with the depth direction partial to the smaller end along with the tooth length The methods of improving the preload for the differential after adjusting the meshing clearance of the spiral bevel gear make sure the clearance 52 Service Manual Driving Axle between the tapered roller bearing on both sides of differential to zero The method for adjusting is shown in the following table Adjustment of contacting area and clearance in assembly of spiral bevel gear Tooth flanks contacting area of Adjustment method The moving driven spiral bevel gear direction of gear Move the driven gear to the driving gear if the clearance is too small move the driving gear to the outside Move the driven gear away from the driving gear if the clearance is too large move the driving gear to the inside Move the driving gear to the driven gear if the clearance is too small move the driven gear to the outside Move the driving gear away from the driven gear if the clearance is too large move the driven gear to the inside The method of adjusting the meshing area is used by adding or removing the adjusting shim and turning the adjusting nuts generally The service performance and life is greatly influenced by the
27. ghtening 8 Never further use those bearing seats and oil seal seats with crack serious wear collision or sheet exfoliation on the touching surface or spigot 9 Never further use those gaskets of the planetary gear and bevel gear with serious wear crack collision or sheet exfoliation 10 Never further use those pins with serious wear collision or crack 55 Service Manual Driving Axle 11 Never further use those supporting shafts half shafts and flanges with collision serious wear and cracks on the spline or teeth or with cracks on working surface at oil seals and bearings 12 Never further use those parts such as axle shell supporting shafts and half shafts with cracks or micro cracks in transition areas or nearby those areas on their arcs chamfers splines IV If it is hard to judge by watching and touching check it by measurement The common standard criterions of easily wear parts are listed in the following table Standard Criterions Parts Checking Items Dimension Tolerance Internal diameter 0 0 02 l tolerance Bearings Gears External diameter 0 0 02 tolerance Wear volume of isis hee Bevel gasket gear External diameter Internal diameter The tolerance Common parts O28 7 External diameter is denoted as of common fits T l The tolerance Internal diameter denoted as of common fits 56 Oversize Measures Allowable Limits 0 02 0 04 12 of
28. haccsdeesnaddaUueeseverseweaeess 4 Chapter V Standard Criterion of Maintance and Parts Replacement for the Axle ee 55 Service Manual Driving Axle CHAPTER I INTRODUCTION 1 1 Safety Notices A IMPORTANT SAFETY WARNING It s very important for the loader s safety to keep maintenance and repairing The related technologies about how to assemble and disassemble the driving axle are described in this manual The safety considerations marked with Aas the security label should be paid more attention when operate it for avoiding hurting relation persons It should keep themselves safe first and take some necessary measures when the potential dangers coming A Security Attentions During assembling and disassembling parts worn out and lives shortened properties deterioration and unsafe factors would be caused by the incorrect operation method Please read the contents carefully in this manual when assembling or disassembling 1 The parameters graphs and contents in this manual are suitable to the standard configuration products Please consult our company and search data about the information for deformed products 2 In repair shop the region for assembling or disassembling and placing disassembled parts should be marked obviously Make sure the tools and parts for special using or are placed in the special region The clean of operation region must be kept and make sure no oil or pollution in the operation region Fir
29. he Assembly of Driving Axle 4 1 The Network Figure of the General Assembly 2 Sleeve gasket 3 Hub 4 Bearing 5 Inner gear 6 Round nut i Planet 1 O ring gear Fix the driving grame axle shell on the Plug LG953 driving assembling jig axle assembly after cleaning 10 Refueling 11 Brake 12 Refueling 13 Main drive assemly 14 15 Sun gear Shield ring 16 Semi axis 17 18 Locating block Steel ball 19 End cover 29 Service Manual Driving Axle Assembly Tools and Equipments Using Position corresponding to the Specification Number serial number of network chart or assembly parts name Select different specification according to the size of the assembly bolts Select different specification according to the size of the assembly bolts Partial assemble the active driving axle assembly and install the input flange Lightly beat the parts with assembly magnitude of interference Clean every parts Partial assemble the active spiral bevel gear assembly Install the fixture pin of the half axis gear gasket and the active spiral bevel General tool name Gas tri MI16 MI17 MI18 RERE MI2000P Ki Sieve 13 16 17 18 21 24 30 34 41 50 SrOuP Dial Indicator 0 01 0 10 1 Pl
30. he differential mechanism Table for screw fasteners in grade B of the driving axle Bolts for hub and brake disc Bolts of brake clip Bolts and nuts connecting planet carrier and hub Bolts for fastening flanges Bolts connecting bracket and bearing chock 31 Service Manual Driving Axle Table for screw fasteners in grade C of the driving axle No position Bolts for racket locking tablets 2 Plug for the center of axle Wheel side plug Assembling methods of A grade screw fasteners 1 1 1 Firstly screw the bolts by more than 2 3 pitches manually 1 1 2 Then pre tighten by gas trigger with low velocity and little torque on the principle of symmetry and cross 1 1 3 In the end using a corresponding specification torque wrench turn 30 at least to reach the median of specification torque 1 1 4 Step 1 1 3 could be substituted by using an intelligent tightening machine But make sure reach the median of specification torque and ensure its accuracy of the machine Principle for tightening B C grade screw fasteners 1 2 1 Firstly screw the bolts by more than 2 3 pitches manually 1 2 2 Secondly pre tighten with the same specification or a one smaller size gas trigger according with cross principle 1 2 3 At last tighten the screw to reach the specification median torque with appropriate gas trigger 4 2 2 Notices in assembling axle 1 Before assembling the scrap iron burrs oil contaminant sedim
31. he length of 15 25 mm from the end face of the bolts a 1262 screw lock fixing sealant 3 3 5 Adjust the spiral bevel gear Meshing status adjustment of the spiral bevel gear is that adjusting the meshing area and meshing clearance When adjusting meshing clearance of the spiral bevel gear pair press the tooth surface of the larger end edge of the driven bevel gear with the percent meter contact And then turn the driven spiral bevel gear to measure its clearance directly The clearance should be within the range of 0 20 0 40 mm The adjusting way of meshing clearance is turn the adjusting nuts to change the position of driven spiral bevel gear move the assembly of driving spiral bevel gear for adjustment if necessarily If the clearance is greater than the specified value move the driven spiral bevel gear nearer to the driving spiral bevel gear on the contrary it should be got away To keep the pre tightening without changing on adjusted tapered roller bearing of the differential The number of the screwing in adjusting nuts at one side should be equal to that out adjusting nuts on the other side When adjusting the contacting area of meshing pair of spiral bevel gears firstly coat red pigment red lead powder etc on the teeth of driven spiral bevel gear generally 3 teeth should be coated then turn the driven spiral bevel gear with reciprocating by hand and check its touching imprint Adjust the proper position of the imprint o
32. ifications torque wrench 9 When assembling the screws bolts and nuts pay more attention to protect such as paint film coating etc on the connected components and also protect such as the head of nuts and bolts and the grooving of the screws etc never damage them 10 Use suitable tap when screw holes need re screw and keep the axle of the screw holes vertically with the surface of connectors 11 After tightening the nuts the bolts and screws should be protruded out 2 3 pitches to the end face of the nuts 12 When a group of nuts or bolts being preloaded make sure preload by many times in a certain order taking account into the distribution condition of connecting components and the bolts 12 1 When tightening a group of nuts or bolts in a rectangle distribution make sure tighten them from the middle to the both sides symmetrically The order is showed in Figure 1 12 2 When tightening a group of nuts and bolts in a square distribution or cycle distribution make sure tighten symmetrically The order is showed in Figure 2 12 3 If having a locating pin tighten from the bolts near the pin The order is showed in Figure 3 I 7 10 eo 9 a Figure 1 Figure 2 Figure 3 13 When fixing heated bearings make sure wear heat insulating gloves in order not to be scalded 14 When using copper rods knock slightly to avoid debris splashing into the cavity of the 33 Service Manual Driving Axle comp
33. ing X _ Planet gear frame 2 1 Paste the needle roller 31 for each in wall of the inner hole on the planet gear with lubricating grease Install the shield ring on the both ends of the needle roller and install gaskets at the both end of the hole on the planet gear And finally install the whole into the seat hole of the planet gear frame Notice Select the needle rollers when assembling to a e _ eS ensure the deviations of max diameter and min diameter are less than 0 005 in the same group The qualified fitting bought from Lingong of Shandong can satisfy the requirement to assemble directly 2 2 Install the steel ball which is aligned to the semicircular cavity of the planet gear frame into the hole of the planet gear axis Then install them and planet gear axis on the planet gear frame passing through the inner hole of the planet gear and gasket After assembling completely the planet gear should rotate flexibly and has no jamming 43 Service Manual Driving Axle 3 Install the main driving assembly Input flange Bolt washer_ Bracket Active spiral bevel gear assembly Adjusting nut Bearing seat Bolt yrasher 3 1 1 Press the external ring of the rolling bearing 3 in the seat hole of the bearing sleeve 3 1 2 Install the rolling bearing 1 on the end journal of the active spiral bevel gear divided into left and right lateral front a
34. le of LG953 axle It is similar with other serial productions in our Corp on axle principle only some small differences in connection types and local structures Those differences will not describe in here and could be executed referred to the relation chapter in this manual ATTENTION Forgiving without further notice about the specification s changing of the parts in this manual which are caused by the driving axle development The latest information could be got or consulted from Shandong Lingong Construction Machinery CD LTD MI Service Manual Driving Axle Table of Contents PRE TEA CB ssc cesdeteaitcts ce citeae Geheaniret date ded de aa E en dateae leacra enum sueaieiass Error Bookmark not defined CHAPTER OITIN PRODUC TION sier aa cant vaelGeun iain rte eet l lak Sale by COn deri ON Saia E E a E O O l L2 OAT Coane Materials ecserin einen E E TE E E E 3 EOM IRE ine E a ate er E A E A E iy sonaaweisoeeny 4 L4 Hoistme ExXplana NOM eene E adel Lisa dls ha Byatt dha 4 1 5 Table of Tightening Torque for Common Bolts cc csssssssssssseeececeeceeeeeeeeeeeaaeaseeeeseeeees 6 CHAPTER IT CONSTRUCTION AND WORKING PRINCIPLE OF THE DRIVING AXLE 7 DN QUIUSIOGS VIEW eiaeia a e E a AA a E E S A a e E RE ARRE 7 22 TCM Al VIEW nesnice nana e a e any dimen eae ease yieasaaaee ed 8 2 5 The Internal Construction Of Drivin Axle scsecesncodsionlccmeie TS sone ae adwdeeee 8 24 Working Principle of the Drvne AK
35. n the end with shield ring groove of the half axis 15 Install the shield ring Install the shield ring with axial circlip plier A Make sure the circlip plier is clamped firmly during operating to avoid bouncing off the box body and forming hidden danger 38 Service Manual Driving Axle 16 Install the half axis Install the half axis with the sun gear in the hub pay attention to the assembly of the half axis spline and gear 17 Install locating block Rivet the steel ball on the locating block to make sure flexibly rotate the steel ball 18 Install the steel ball Install the locating block riveted steel ball on the end cover If the locating block unreached to the desired position lightly beat it with corresponding tool until the steel ball can rotate flexibly 39 Service Manual Driving Axle 19 Install the end cover Coat the glue line with diameter 4mm according to the route shown in the right Figure Coat appropriate 1262 screw lock fixing sealant in the thread hole at the joint bottom between hole and bolt Finally tighten the cover with the bolt and washer Tightening torque 45 5Nm i Notice Fasten each bolt according to the symmetric cross method 7 51262 screw lock fixing sealant 40 Service Manual Driving Axle 4 4 Partial Assembling of the Assembly 1 Assemble the hub assembly Hub Rolling bearin Bolt wash
36. of 3 10 17 8 screw holes Explanation about Disassembling Parts Specification Number 1 Never reuse the disassembled parts and make sure replace them with the new ones 2 Magnitude of references for partial bearings are relatively bigger because they were assembled by heated and pressed assembling in their corporations which will bring injury to bearings when disassembling Those bearings whose surfaces are damaged in disassembling could be reused when repaired and satisfied the using standard otherwise are dealt as scrap bearings 3 When the copper bar is used knock the parts as lightly as possible to avoid the debris splashing into the assembly parts also you can choose rubber hammer plastic hammer or other press assembly methods Preparative work 1 Clean the soil and fouling on the duplex driving axle assembly completely 2 Prepare firmly driving axle assembling carrier Service Manual Driving Axle 3 2 Disassembly of driving axle 1 Place the driving axle assembly on carrier horizontally Make the main driving axle assembly up Driving Axle Assembly 2 Disassemble the brake clip assembly Use corresponding specification tools Such as sleeve and open end wrench etc the following conditions are similar and without explainning again Loose off the bolts connect the brake clip assembly and carrier Disassemble the brake clip assembly 3 Disassemble end cover Loose off bolts connect the plane
37. of the driving axle and joint to the bracket with the bolt and washer preload the bolt M14 55 and M12 55 Install the input flange 50 Service Manual Driving Axle Coat the sealant on the end surface of the gasket and the keep the coating surface downward and then r The line of install the gasket smearing sealant on the washer 609 sealant Install the nut M33 1 5 and tighten it Tightening torque of the nut 320 400 Nm Notice 1 Before installing the flange install the flange on the spline of the active spiral bevel and measure the radial pulsation of the flange to assure not more than 0 08 and make matching and assembly marks If more than 0 08 rotate and install the flange to a certain angle then measure again until satisfy the requirement Otherwise change the flange 2 Coat a glue line whose coarseness is D2 03 according to the line showed in the Figure on the washer as close as possible to the external circular 3 3 4 Assemble the differential mechanism assembly Turnover the bracket install the differential mechanism assembly in the bracket C o Differential mechanism assembly 51 Service Manual Driving Axle Install the bearing seat with the washer and bolts the bolt is lightly tight then install the adjusting nut Attention 1 Never change the two bearing seats 2 Coat proper amount of the 1262 screw lock fixing sealant on t
38. of the rolling bearing 31313 then hook the hole 14 5 on the bearing sleeve with pull tensile dynamometer which is pulled along the tangential direction The reading of the pull tensile dynamometer is 5 35 N If the reading is not within 5 35 N increase and reduce the thickness of the gasket Repeat the above processes until the reading scope is within 5 35N 3 2 1 Install the half axis gear Install two fixed pins and the half axis gear gaskets in the left shell of the differential mechanism in order Notice Beat lightly when install the fixed pin to prevent the range of dimension tolerance out Of Semiaris gear gasket ane measure with the caliper while beating Install the half axis gear It is necessary that coat the lubricating oil when install the half axis gear gasket and the half axis gear The surface with oil groove of the half axis gear gasket combines with back of the half axis gear 46 Service Manual Driving Axle Lubricating oil 3 2 2 Install the half axis gear Install two fixed pins the half axis gear gasket and half axis gear in the right shell of the differential mechanism in order Notice Beat lightly when install the fixed pin to prevent the range of dimension tolerance out of 2 95 measure with the caliper while beating 3 2 3 Assemble the cross assembly Install bevel gears smaller end inward and bevel gear gaskets on the four axis ends of the cross X Notice
39. onents otherwise use rubber hammer plastic hammer or the way of press mounting instead 4 3 Driving Axle Assembly 1 The assembly of the driving axle shell Make sure hang the cleaned axle shell on the special support Wring the plug with glue spread on the oil letting and fuel deliverer of the axle belly Driving axle shell kgm Tightening torque of the plug 70 100Nm 2 Sleeve gasket Install the gear sleeve gasket on the wheel side supporting axle of the axle shell assembly 3 Hub assembly De ty ti TOR ii Coat the lubricating oil on the wheel side supporting axle of the axle shell assembly and then install the hub j NN assembly on the both ends of the support axis of the axle shell assembly Z lt Lubrication oil 4 Bearing Heat the inner ring of rolling bearing 32221 to 50 80C and then install it on the wheel side supporting axle 34 Service Manual Driving Axle 5 Internal gear Install internal gear of the driving axle on the spline at the end of supporting axle PAPE N R 6 Round nut r A y ia Install and fasten round nut Notices 1 Hook the 22 5 hole with the pull tensile dynamometer and pull along with the tangential direction The reading of the pull tensile dynamometer is 45 75N If the reading is not within the scope between the 45 75N adjust the degree of tightness of the round nut according to the reading Repeat the above operations until
40. operator must keep away to safe region to work During this operation the carrier must be pushed carefully for avoiding too fast to fall it down resulting in potential safety hazard 11 O shape ring Take off the O shape ring from planetary wheel carrier by hand 12 Disassemble round screws Loose the round screws off with corresponding specification tools first And then disassemble them by hand Service Manual Driving Axle 13 Disassemble internal gear ring Take off the internal gear ring by hand 14 Disassemble rolling bearing Take down the internal ring of 32221 bearing by hand 15 Disassemble hub assembly Take down the hub assembly from wheel side support axis _s Hub assembly During hanging disassembling keep the axis of hub assembly approximately coincide with the axis of wheel side support axis to avoid hurting the oil sealing cover and its internal parts 16 Disassemble the sleeve gasket Take down the sleeve gasket Remark Disassemble all the parts on the other side of driving axle with the same method Service Manual Driving Axle 17 Disassemble main driving axle assembly Loose off the screws connecting the main driving axle and axle shell assembly with relevant size tool and hang driving axle assembly off Main driving axle assembly When hanging main driving axle assembly make sure keep the hanging tool upright above the driving axle ass
41. riving Axle 4 Take down frame oil seal from seal cover with specific tool 5 Take down gasket by hand 6 Turn over the main driving 180 7 Disassemble locking iron wire The structure of some machines may be not the same as this Figure Adjust disassembling contents in actual operations 23 Service Manual Driving Axle 8 Loose off the bolts fix locking plate and take down locking plate 9 Mark the part for reinstalling it to the initial position 10 Loose off the bolts connecting the bearing seat with corresponding specification tool and dismount the bearing seat 11 Dismount the adjusting nuts by hand 24 Service Manual Driving Axle 12 Knock down the locking plate of stop pushing bolt and dismount the nuts Take down locking plate and dismount stop pushing bolt 13 Hang out the differential mechanism assembly oe l Differential mechanism assembly A keep balance during the hanging operation to avoid bringing potential safety hazard 14 Break away the driving spiral bevel gear assembly and bracket with copper bar A Never knock the spiral bevel gear assembly too abruptly to avoid it falling down to scratch parts or bring potential safety hazard 3 3 4 Disassemble the differential mechanism assembly 1 Put differential mechanism assembly on the working table vertically and firmly 25 Service Manual Driving Axle 2 Loose off the nu
42. rope and hook is the heavier of each rope loads The Figure 1 2 shows the changes of allowed loading kg in different angles when hoisting with two ropes The limited vertical hoist loading of each rope is 1000 kg It can hoist 2000 kg when two ropes in the vertical location But when the angle reaches to 120 the ropes can only hoist 1000 kg Another hand the force of the ropes would be 4000 kg when the angle reaches 150 although the loading is only 2000 kg Load qauntity Kg Hanging angle e d Figure 1 2 Service Manual Driving Axle 1 5 Table of Tightening Torque for Common Bolts Nominal Diameter of Bolts mm a e 46 240 4 5 10512 20 25 36 45 55 70 28 a T ee ee 9 es j eo onr 930 ss a a aes 109 900 13 16 30 36 65s 78 1mo 130 f 180 210_ 129 1080 teer asesi 75 100 131 175__ 209 278 _ jeld Nominal Diameter of Bolts mm _ te wg OH Tightening Torque Nm _ _ _ 46 240 90 110 120 150 170 210 230 290 300 377 5 6 300 110 140 150 190 210 270 299 350 370 450 68 480 145 193 199 264 282 376 384 512 488 650 88 640 193 257 264 354 376 502 521 683 651 868 10 9 900 280 330 380 450 540 650 740 880 940 1120 129 1080 326 434 448 597 635 847 864 1152 1098 1464 ne ae Tightening Torque N m 450 530 540 680 670 880 900 1100 928 1237 56 300 550 700
43. tary carrier and cover by corresponding specification tools Push end cover away from wheel side assembly with M10 pusher screw Disassemble end cover 4 Disassemble the locating block Take off the locating block and steel balls together by hand Corresponding specifications could be used when the parts are a little tight Service Manual Driving Axle 5 Disassemble the steel balls Remove the locating point of steel balls with tools and S make them out 6 Disassemble shield ring Take out the shield ring from half axle ring groove by axis shield ting clip Before disassemble shield ring partially pull out the half axle and its parts from axle shell A Make sure that the pliers be clamped firmly to avoid bouncing off to resulting in potential safety hazard 7 Disassemble the solar gear Take off the solar gear from half axle slightly by hand 8 Disassemble half axle Take off the half axle from axle shell slightly by hand Service Manual Driving Axle 9 Plug screw Loose plug screw with corresponding speciation tools and then unscrew it by hand carefully ye Prepare a clean vessel under it to get oil 10 Wheel side reducer Loose off the hub screws with corresponding speciation tools first And then Push planetary carrier away from hub with M16 pusher screw Disassemble planetary wheel carrier assembly A when push planetary carrier with pusher screw the
44. tion speed and increasing torque from driving axle and have the differential speed function to the two side wheels and bearing load and transmitting power as well Driving axle of the loader is made up of axle shell main driving axle driver including differential mechanism half axis wheel side reducer and brake clip assemblies The parts with the function of reducing or differencing speed are the main driving axle driver and wheel side reducer Main driving axle driver is made up of input flange oil seal cover bearing sleeve driving spiral bevel gear following spiral bevel gear bracket differential mechanism planetary wheels cross shaft half axis gear left shell of differential mechanism right shell of differential mechanism gasket bearings adjusting shim stop pushing bolts and framework oil Service Manual Driving Axle seal Wheel side reducer is made up of internal gear ring planetary wheel carrier planetary wheel solar wheel and shims The main internal structures are shown in Figure 2 1 The power driving axle between main driving axle driver and wheel side reducer is transferred by half axle The splines on the two end of half axle mesh with the half axle gears in differential mechanism and the solar gears in wheel side reducer and it connects the power between main driving axle driver and wheel side reducer frame wheel side bearing seating __ frame seal shell support shaft Na initiative helix a
45. ts connecting driven spiral bevel gear and right shell of differential mechanism Dismount the driven spiral bevel gear position 3 Dismount the bearings of left and right shell of differential mechanism 4 Loose off the nuts connecting left and right shells and separate the left and right shells of differential mechanism x Before separating left and right shells check or mark the assembly label first to reinstall the part to initial position 5 Take down half axle gear gasket and half axle gear 26 Service Manual Driving Axle 6 Take down the cross shaft and differential gears together Dismount differential gear gasket and differential gears from cross shaft 7 Take down the half axis gear gasket and the half axis gear 3 3 5 Disassemble the active spiral bevel assembly 1 Put the active spiral bevel assembly on the corresponding worktable and put up the flange of the bearing sleeve then pull pressure on the thread end of the active spiral bevel with hold down When pulling the pressure should not be so high to prevent harming the cam to let the bearing sleeve pull off the active spiral bevel 2 Take down the bearing 2l Service Manual Driving Axle 3 Take down the bearing sleeve 4 Take down the bearing outer ring 5 Take down the adjusting gasket 6 Take down the sleeve gasket 28 Service Manual Driving Axle Chapter IV t
46. xle is left lateral and back axle 1s right lateral with mechanical press and then install the shield ring in order 3 1 3 Turnover press the rolling bearing 2 on the other end of the active spiral bevel gear with mechanical press Hut Washer Cl seal l T meal cover ES _ Grasket na Adjusting grasket wt GT w A Locking tablet i B WH Bolt nut Copper sleeve Locking tablet Bolt washer Roling bearing 3 Crasket Rearing sleeve Axa a Sr kia gleewe Rolling bearing 2 Active spiral bevel gear Rolling bearing 1 shield ring 44 Service Manual Driving Axle Install the axis sleeve in order Install the gasket Then install the bearing sleeve include the external ring of the bearing 31313 Finally press into the inner ring of the rolling bearing 31313 45 Service Manual Driving Axle X Notice When assemble the main reducer the tapered roller bearing should be preloaded as certain assembly degree that is to say after eliminating clearance between the bearings tighten with a certain pre tightening force in order to reduce axial displacement caused by the axial force produced during the driving axle in order to increase the brace stiffness of the axis to assure the normal mesh of the bevel gear pair But too tight will lowered the wear resistance of the tapered roller bearings Load and keep the pressure P 5420kg on the up end of the inner ring
Download Pdf Manuals
Related Search
Related Contents
EVS Technical Reference 国立大学法人筑波大学において,下記のとおり物品の購入について一般 Frigidaire FFRS0833Q1 Owner's Manual Canon PowerShot A700 User's Manual notice infinicire 086383 Emerson ACE95 Data Sheet User Manual 平成 年 月 日 - 岡山県環境保全事業団 添付文書:90960349-01A - Boston Scientific 251 COMPTES RENDUS ODILE MARCEL (dir.), Paysage modes d Copyright © All rights reserved.
Failed to retrieve file