Strut Spring Compressor
Contents
1. washer D31 x D16 2 x 4T L Bracket washer D30 x D13 x 5T bolt M16 x P2 x 90L nut M16 x P2 leg assy for option only support leg swivel wheel assy swivel wheel assy bolt nut nylon washer label s not shown manual OIPM 90000 01 Quantity OBRANNNMHAHROH HHA BRNYNDYD Figure 7 Replacement Parts Illustration for Model Atd 7553 Atd Tools Inc Bec 114 1 70 Trade Center Drive St Peters MO 63376 PREMIUM PRODUCTS Tel 636 272 9050 Fax 636 272 90442. and tighten using Bolt 17 OWNER USER RESPONSIBILITY The owner and or user must have an understand ing of the manufacturer s operating instructions and warnings before using this equipment Personnel involved in the use and operation of this device shall be careful competent trained and qualified in the safe operation of the equipment and its in tended use Warning information must be empha sized and understood If the operator is not fluent in English the manufacturer s instructions and warnings shall be read to and discussed with the operator in the operator s native language by the owner purchaser making certain that the opera tor comprehends its contents It is recommended that an annual inspection of the product be made by a factory authorized repair facility It is owner s user s responsibility to ensure that product label and instructional material is legible and accessi ble Replacement labels and manuals are avail able from the manufacturer Note Before using apply a light coating of bearing grease to mid section of upright OPERATING INSTRUCTIONS 1 Secure base of strut in compressor fixture by adjustable strut shaft clasp Secure spring with claw assembly Pump to compress spring Install safety bar in upright directly above strut spring channel please refer fig 6 Remove nut and retainer cup assembly Decompress spring and remove Replace damaged components Install spring and c
3. not extend to full extension Fluid level low Ensure proper fluid level ONE YEAR LIMITED WARRANTY For a period of one 1 year from date of purchase Atd Tools Inc will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship or which fails to conform to any implied warranty not excluded hereby Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to Atd Tools Inc Warranty Service Department 114 I 70 Trade Center Drive St Peters MO 63376 Except where such limitations and exclusions are specifically prohibited by applicable law 1 the CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE and 2 Atd Tools Inc SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDEN TAL DAMAGE OR LOSS WHATSOEVER and 3 THE DURATION OF ANY AND ALL EXPRESSED AND IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO A PERIOD OF ONE 1 YEAR FROM DATE OF PURCHASE Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rig
4. RDWARE KEEP FEET AND HANDS FROM LOADING AREA NEVER LEAVE LOADED SPRING COMPRESSOR UNAT TENDED ENSURE THE USER IS THOR OUGHLY FAMILIAR WITH THE CONTROLS AND OPERATIONAL CHARACTERISTICS OF THIS PRODUCT AND IS AWARE OF THE PO TENTIAL HAZARDS ASSOCIATED WITH ITS USE ALWAYS WEAR SAFETY GLASSES WHEN USING USE ONLY ON HARD LEVEL SURFACES DO NOT USE THIS DEVICE FOR ANY PURPOSE OTHER THAN THAT FOR WHICH IT IS INTENDED FAILURE TO HEED THESE WARNINGS MAY RESULT IN FATAL INJURY AND OR PROPERTY DAMAGE NOTE WALL MOUNT IS NOT FOR USE ON WOODEN STUDS SHEET ROCK OR SIMILAR MATERIALS ASSEMBLY please refer fig 7 on page 7 A For beam mount 1 Attach Lower Wall Brackets 14 8 16 to Up right 13 using 4 Bolts 15 8 Washers 20 and 4 Nuts 26 Please refer fig 2 connect to base connect to 1st amp 3rd hole wall a left lower wall bracket Fig 2 2 Slide Strut Support 7 onto Upright Secure in lowest possible position using 2 Bolts 31 and 2 Nuts 32 Attach L Bracket 29 Adjust able Strut Shaft Clasp 10 and Washer 28 to Strut Support using Knob 27 3 Slide Strut Spring Channel 18 onto Upright Attach Spring Clasp Bracket 22 to Strut Spring Channel and secure in horizontal posi tion with Bolt 8 Attach Spring Clasp Holder 23 to Bracket using Wing Nuts 19 Wash ers 30 and Springs 21 Attach Spring Clasps 24 to Holders using Bolts 25 Wa
5. Strut Spring Compressor Operating Instruction amp Parts Manual Model Number Atd 7553 Model Atd 7553 Atd Tools Inc 114 1 70 Trade Center Drive St Peters MO 63376 Printed in Taiwan Save these instructions For your safety read and understand the information contained within The owner and operator shall have an understanding of this product and safe operating procedures before attempting to use this product Instructions and Safety information shall be conveyed in the operators native language before use of this product is authorized Make certain that the operator thoroughly understands the inherent dangers associated with the use and misuse of the product If any doubt exits as to the safe and proper use of this product as outlined in this factory authorized manual remove from service until which time itis clear Inspect before each use Do not use if broken bent cracked or otherwise damaged parts are noted If the product has been or suspected to have been subjected to a shock load discontinue use until checked out by an authorized factory service center Owners and operators of this equipment shall be aware that the use and subsequent repair of this equipment may require special training and knowledge lt is recommended that an annual inspection be done by qualified personnel and that any missing or damaged parts decals warning safety labels or signs be replaced with factory authorized replacement parts only I
6. f this product appears to be damaged in any way is worn or operated abnormally should be removed from service immediately until such time as repairs can be made PRODUCT DESCRIPTION Atd Tools Heavy Duty Strut Spring Compressor Model Atd 7553 is designed as an aid in safely replacing strut springs SPECIFICATIONS Recommended Max Working Model Product Size LXWXH Strut Spring Dia Space Hydraulic Stroke Atd 7553 12 1 4 X 11 7 8 X 52 5 8 4 10 15 1 2 10 14 1 4 Max 4 Ya Min BEFORE USE Note Never service strut spring compres sor while in use 1 Familiarize yourself with this tool and the haz ards associated with its improper use 2 Always refer to and have available a credible service manual covering the year make and model of the vehicle being serviced Follow manufacturer s guidelines for strut removal service and installation procedures 3 Inspect before each use DO NOT USE if bent broken cracked or leaking parts are noted Repair or replace with factory authorized com ponents only 4 No alteration of this device is permitted A WARNING d READ AND UNDERSTAND ALL PRINTED MA TERIALS PROVIDED WITH AND ON THIS DE VICE ENSURE WORKPIECE IS COMPATIBLE A APESI Ala AnS WITH AND IS SECURELY FASTENDED IN COM PRESSOR FIXTURE ONLY COMPRESS upright Ha ram release valve knob hydraulic pump handle SPRING SUFFICIENTLY TO REMOVE RETAIN ING NUT AND HA
7. hts and you may also have other rights which vary from state to state REPLACEMENT PARTS When ordering replacement parts please refer to the model number serial number found on the product then give the part number and description Available Parts Please refer to the Parts drawing when ordering parts Not all components of the jack are replace ment items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts give Model number serial number and description below Call or write for current pricing Atd Tools Inc 1141 70 Trade Center Drive St Peters MO 63376 Tel 636 272 9050 Fax 636 272 9044 Model Atd 7553 Parts No OONODOOABRWND Description ram plunger hydraulic pump ram bracket spring clip bracket pin D15 8 x 96 ram position pin D10 x 76 strut support bolt M10 x 1 5 x 10L washer D20 x D10 4 x 1 2 adjustable strut shaft clasp wall bracket upper bolt M10 x 1 5 x 16L upright wall bracket lower left bolt 1 2 12UNC x 1 1 4 wall bracket lower right bolt M8 x 1 25P x 15L strut spring channel wing nut 1 2 12 UNC washer D24 x D13 x 2 5T spring D18 x D2 x D15 Quantity 4 4 4 2 1 1 1 1 1 1 1 2 1 1 4 1 1 1 4 8 2 Je o o o ooo o ooo o o 9 00 a Parts No Description spring clasp bracket spring clasp holder sping clasp claw screw 1 2 12 UNC x 1 2 nut W1 2 x 12 UNC knob
8. ompress Install retainer cup assembly and nut WP OOND Ol 10 Tighten retainer nut 11 Remove safety bar from operation step 4 position Reposition to near top of upright channel 12 Decompress spring and remove strut assembly from fixture MAINTENANCE Lubrication of upright is required in normal serv ice If service environment has a history of pro ducing rust it may be necessary to coat all ex posed surfaces with a light machine oil DO NOT allow lubricant to contact claw assemblies nor strut springs IF SO clean and dry thoroughly before use in the spring compressor insert to upright g S g 8 8 S e ee ee e e TROUBLESHOOTING Symptom Possible Causes Corrective Action Ram will not extend Release valve not tightly closed Overload condition Ensure release valve tightly closed Remedy overload condition Ram bleeds off Release valve not tightly closed Overload condition Hydraulic unit malfunction Ensure release valve tightly closed Remedy overload condition Contact Atd Tools Tech Service Ram will not retract after unloading Reservoir overfilled Linkages binding Drain fluid to proper level Clean and lubricate moving parts Poor performance Fluid level low Air trapped in system Ensure proper fluid level With ram fully retracted remove oil filler plug to let pressurized air escape reinstall oil filler plug Will
9. s using Bolts 25 Washers 30 and Wing Nuts 19 4 Attach Ram Bracket 3 to Upright using 2 Bolts 31 and 2 Nuts 32 5 Attach Ram Plunger 1 to Bracket using Ram Position Pin 6 Washer 9 and Spring Clip 4 Insert Ram Piston into Strut Spring Chan nel 18 and tighten using Bolt 17 Note Hardware needed to secure product to beam is not included C Support leg option 1 Attach each Support Leg 37 to Upright 13 using 4 Bolts 40 4 Nuts 41 and 8 Wash ers 42 please refer fig 5 amp 7 Fig 5 Note Do not attach lower wall brackets with support leg option Slide Strut Support 7 onto Upright Secure in lowest possible position using 2 Bolts 31 and 2 Nuts 32 Attach L Bracket 29 Adjust able Strut Shaft Clasp 10 and Washer 28 to Strut Support using Knob 27 Slide Strut Spring Channel 18 onto Upright Attach Spring Clasp Bracket 22 to Strut Spring Channel and secure in horizontal posi tion with Bolt 8 Attach Spring Clasp Holder 23 to Bracket using Wing Nuts 19 Wash ers 30 and Springs 21 Attach Spring Clasps 24 to Holders using Bolts 25 Washers 30 and Wing Nuts 19 4 Attach Ram Bracket 8 to Upright using 2 Bolts 31 and 2 Nuts 32 Attach Ram Plunger 1 to Bracket using Ram Position Pin 6 Washer 9 and Spring Clip 4 Insert Ram Piston into Strut Spring Chan nel 18
10. shers 30 and Wing Nuts 19 4 Attach Ram Bracket 8 to Upright using 2 Bolts 31 and 2 Nuts 32 5 Attach Upper Wall Bracket 11 to top of Up right using 2 Bolts 12 6 Attach Ram Plunger 1 to Bracket using Ram Position Pin 6 Washer 9 and Spring Clip 4 Insert Ram Piston into Strut Spring Chan nel 18 and tighten using Bolt 17 Note Hardware needed to secure product to wall is not included B For bench or floor mount 1 Attach Lower Wall Brackets 14 amp 16 to Up right 13 using 4 Bolts 15 8 Washers 20 and 4 Nuts 26 please refer fig 3 for bench or fig 4 for floor Note Bench table must be minimum 3 4 thickness if hardwood or pressboard is used connect to base 1st amp 3rd hole ee ee left lower wall bracket connect to bench Fig 3 connect to base 2nd 8 3rd hole left lower wall bracket 2 Slide Strut Support 7 onto Upright Secure in lowest possible position using 2 Bolts 31 and 2 Nuts 32 Attach L Bracket 29 Adjust able Strut Shaft Clasp 10 and Washer 28 to Strut Support using Knob 27 3 Slide Strut Spring Channel 18 onto Upright Attach Spring Clasp Bracket 22 to Strut Spring Channel and secure in horizontal posi tion with Bolt 8 Attach Spring Clasp Holder 23 to Bracket using Wing Nuts 19 Wash ers 30 and Springs 21 Attach Spring Clasps 24 to Holder
Download Pdf Manuals
Related Search