Corbin Russwin IN120 Mortise Lock Installation Instructions
Contents
1. Fig 17a Fig 17b Detail Copyright an oroin se me an ASSA ABLOY peop company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 17 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock RGP 7A ASSA ABLOY 5 Installation Instructions Continued 12 Installing Batteries Before installing batteries for the first time Remove pull tab from its position beneath the coin cell by pulling on tab in direction of arrows printed on tab Fig 18 1 Place 6 AA alkaline batteries in the compartment being careful to align polarity properly 2 After batteries are installed there is a slight delay then an audible beep will sound and the lock motor will cycle Twenty 20 seconds after lock initialization single beep with lock motor actuation 13 Inside Cover Installation 1 Assemble cover by hooking top edge on inside mounting plate 2 Carefully press bottom of cover toward door without pinching any wires 3 Fully secure cover by tightening the security screw at bottom of cover Fig 19 utilizing the security allen wrench provided Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or2. IN120 Mortise Lock RgerbinyA ASSA ABLOY 5 Installation Instructions i Verify Hand and Bevel of door Illustrations shown are as viewed from the outside or secure side of opening UUE Left Hand Left Hand Right Hand Right Hand Hinges Left Reverse Bevel Hinges Right Reverse Bevel Open Inward Hinges Left Open Inward Hinges Right LH Open Outward RH Open Outward LHRB RHRB 2 Door Preparation Prep door according to supplied door marker FM355 For door manufacturer templates visit www corbinrusswin com and reference template T31202 Outside Face of Door Inside Face of Door Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 6 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock Rgerbiny ASSA ABLOY 5 Installation Instructions Continued 3 Install Door Position Switch DPS a Push wires through raceway toward lock prep b Push DPS firmly into place by hand Note DO NOT TAP SWITCH WITH ANY TOOL c Install magnet into door frame Push firmly into place by hand See instruction A7983B Only required on the ML201xx lock body ML202xx has an integrated DPS Inside of Door Collar is used only with metal doors CAUTION if DPS is not installed or is installed
3. responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equip ment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced technician for help The term IC before the ra
4. Outside Face of Door Inside Face of Door Outside Adapter late Inside Face of Door Outside Face of Door Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 10 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock corbin ASSA ABLOY 5 Installation Instructions Continued Step 4 k a Use Correct Spindle Orientation b Inside Face of Door r Fig 9a y S 2 b bE N A W Fig 10c Er Fig 10b Adjustment bolt needs Adjustment bolt needs Adjustment bolt fully aligned o be threaded in farther to be unthreaded Step6 Install I S lever with set screw T Inside Lever N Notes e Unthread adjustment bolt approximately four turns for a good starting point after being fully tightened e Make sure O S lever is fully inserted into adapter plate before aligning adjustment bolt Fig 11 Copyright an oroin se me an ASSA ABLOY peop company g All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 11 ASSA ABLO
5. e nd user n eeds for secu rity Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company safety a nd convenience All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited
6. IN120 WiFi Corbin 7 Mortise Lockset Russwin Installation Instructions ASSA ABLOY FM353 03 15 617419050 Attention Installer Please read these instructions carefully to prevent missing important steps Please Note Improper installations may result in damage to the lock and void the factory warranty Important The accuracy of the door preparation is critical for proper functioning and security of this lock Misalignment can cause premature wear and a lessening of security For Technical Assistance call Corbin Russwin at 1 800 810 WIRE 9473 Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock corbin ASSA ABLOY Table of Contents DY WANING soian aani aa 2 General DESCHIOTION siissiinsnesanscesnsinnssinevsnenyvassnnseceaeinennaninanis 3 Specifications Features sssssssssnsnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnn 2 3 3 4 Product Illustration ssssssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 5 Installation Instructions ssssssssssnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 9 6 Operational Check ssssssnssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 1 Warning Changes or modifications to this unit not expressly approved by the party
7. ferrite bead and excess cable into wire hole on inside of door e Secure the mounting assembly while ensuring proper alignment of outside reader and tighten the 2 through bolts on the inside of the door to secure the reader Fig 16c IE ie J e Fig 16c Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 16 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock 11 5 Installation Instructions Continued RUSWANA ASSA ABLOY Installing the Controller a Insert bottom tab of controller into slot on mounting plate Fig 17a b b Looking down from top of controller ensure proper alignment of board to board connectors Fig 17b while pivoting controller toward door until two tabs on top snap securely into place on mounting plate Fig 17a CAUTION To avoid possible damage to board to board connectors care should be taken when securing controller to mounting plate If there is resistance when securing detach controller to determine cause before re attaching controller Inside Face of Door Controller gt in Board to Board Connectors AF TE Fai T 3 j J Bj Fig 17b
8. global leader in door opening solutions express written permission of Corbin Russwin Inc is prohibited IN120 Mortise Lock 5 Installation Instructions Continued RUSWANA ASSA ABLOY 8 Install Turn Piece Step 1 Step 2 a Step 3 t Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 14 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock Corbin 7a Russwin ASSA ABLOY 5 Installation Instructions Continued 9 Install Outside Reader and Inside Mounting Plate a Orient the reader so the LED lens is at the top b Feed the cable connector through the door from outside to inside c Install the reader to the outside of door by aligning the mounting posts with the door preparation holes Hold the reader flush against door while ensuring proper alignment d Next feed the cables connectors through the inside mounting assembly and gasket if required NOTE Cable lengths exaggerated for illustrative purposes Inside Face of Door Outside Face of Door Reader Cable Reader Cable Q A wD Fig 15a Xe Gasket is required for outdoor installations Do not use gasket for fire rated
9. openings If installing with gasket separate gasket from mounting plate to feed cables connectors through holes as indicated Fig 15b Once cables connectors are fed through reattach gasket to mounting plate Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 15 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock 10 Installation of Connectors CAUTION Do not touch or allow debris to enter connector contacts Secure the following connectors to their respective terminals Fig 16a b a Secure the 24 pin card reader connector b Secure the 4 pin DPS connector c Secure the 10 pin lock body assembly connector NOTE Optional 2 pin external 12 24VDC power connector Ground Anchor Reader 24 pin RUSWANA ASSA ABLOY 5 Installation Instructions Continued DPS 9 24VDC 4 pin Power Q T Board to Board ee Q Connector Fig 16a PA i Lock Lx JOI Body H ZO N 10 pin Ground Lug o E Wire Positioning Inside of Door Please follow these steps prior to installing inside escutcheon to prevent any damage caused by pinching wires d When all connections have been made tuck
10. Install Lock Body in Door a Feed wires through 1 5 16 diameter hole on INSIDE of door while installing lock body Fig 6a b Pull wires through hole while inserting lock body DO NOT push wires back into cylinder hole Fig 6b Important Door must remain open during installation Use door stop c Install but do not tighten two 12 x 1 combination screws through lock body Fig 6a Inside Face of Door From Lock Body 2 12 x 1 Do not tighten Fig 6b 6 Install Cylinder a Slide cylinder through collar Thread cylinder into lock body Fig 7a Note Make sure cylinder is oriented correctly Fig 7a1 1 b Tighten cylinder clamp using 7 64 allen wrench provided Fig 7b c Turn the key to make sure that lock functions correctly 9 9 9 B S latch deadbolt and key Position cylinder so that the logo is right PS Correct Incorrect 7 64 Allen Wrench Fig 7a1 Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 9 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock ncorbin7 ASSA ABLOY 5 Installation Instructions Continued 7a Install Standard Lever Trim Refer to 7b on following pages for Museo Trim Step 1a Step 1b
11. SS SE 1O enabled HID iCLASS Seos HID MIFARE White 1 SE HID DESfire EV1 SE HID Prox NFC enabled mobile phones IN 120 EM01 IP MB finish HID iCLASS HID iCLASS SE SI0 enabled HID iCLASS Seos HID MIFARE Black with metal trim 4 SE HID DESfire EV1 SE HID Prox NFC enabled mobile phones IN 120 EM01 IP MW finish HID iCLASS HID iCLASS SE I0 enabled HID iCLASS Seos HID MIFARE White with metal trim 1 SE HID DESfire EV1 SE HID Prox NFC enabled mobile phones IN 120 EM01 IPS B All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 IN 120 EMO1 IPS W All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 IN 120 EM01 IPS MB finish All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 Black with metal trim IN 120 EM01 IPS MW finish All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 White with metal trim IN 120 EMO1 CP B FeliCa HID Prox NFC enabled mobile phones FeliCa HID Prox NFC enabled mobile phones Pz Terie nsawo kt mountings Barware OO Oooo CY af e wo S AEE E E E E T Inside Escutcheon ae Be FIN Inside Escutcheon paren with metal trim 783F735FINX FIN Inside Escutcheon White with metal trim with metal trim 6 FM355 Field prep template not shown Pt 731202 Door manufacturers template not shown a aa 3 FM353 I
12. Y the global leader in door opening solutions IN120 Mortise Lock 5 Installation Instructions Continued RUSWIn AL ASSA ABLOY 7b Install Museo Trim Step 1 Thread adapter plate hub into lever and fully tighten NOTE Spindle can be used to help thread hub into lever Outside Face of Door Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited Step 2 Align adapter plate hub with square hole in lever keeping as possible hub as tight O JO LAN Fig 13 C Use Correct Spindle Orientation N ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock corbin ASSA ABLOY 5 Installation Instructions Continued Step 4 Install Spindle and Rose a Align studs on rose with bushings in adapter plate Fig 14a Step 5 Install I S lever with set screw Fig 14b Step6 Install Armored Front a Tighten 2 screws through lock body b Attach armored front with two 8 x 1 4 screws Fig 14c a Outside Face of Door gt E SS S cd Q Fig 14c Sii ke a Copyright an oroin se me an ASSA ABLOY croup company Pe lath A Ar an tle a al 13 ASSA ABLOY the
13. ads or solder connections on the circuit boards Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the 2 ASSA ABLOY the global leader in door opening solutions express written permission of Corbin Russwin Inc is prohibited IN120 Mortise Lock rEg ASSA ABLOY 2 General Description The Corbin Russwin IN120 pairs a sleek attractive design with the latest in access control technology to address the evolving needs of today s facilities Featuring HID multiCLASS SE technology this innovative WiFi lock makes it easy and affordable to expand your access control system This product is operated by six 6 AA alkaline batteries or can be hard powered using an optional 12 24VDC power supply connected by a harness through the door Corbin Russwin mortise locks are designed with quality components to provide high security performance and durability 3 Specifications Features e Latch Stainless Steel Easily field reversible without disassembling lock body e Deadbolt Stainless Steel e Auxiliary Latch Stainless steel non handed e Door Thickness 1 3 4 Standard can be furnished for other door thicknesses upon request Consult factory e Case 12 gauge heavy duty wrought steel e Outside lever controlled by reader or key retracts latch e Inside Lever produces REX request to exit signal and retracts latch and dea
14. dbolt e ML20200 offers monitoring of deadbolt REX and provides integrated monitoring of Door Position e UL fire listed Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening and Corbin Russwin Inc makes no representations or warranties concerning what such impact may be in any specific situation When retrofitting any portion of an existing fire rated opening or specifying and installing a new fire rated opening please consult with a code specialist or local code official Authority Having Jurisdiction to ensure compliance with all applicable codes and ratings 802 11 b g n Wireless Access Point Ethernet LAN IN120 EAC Server Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 3 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock Roarbiny ASSA ABLOY 4 Product Illustration Reader Module lt gt aA ITEM PART NUMBER ORDER STRING DESCRIPTION COLOR TRIM 1 IN 120 EM01 IP B HID iCLASS HID iCLASS SE SI0 enabled HID iCLASS Seos HID MIFARE Black 1 SE HID DESfire EV1 SE HID Prox NFC enabled mobile phones IN 120 EM01 IP W HID iCLASS HID iCLA
15. dio certification number only signifies that Industry Canada technical specifications were met This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Cet appareillage num rique de la classe B r pond a toutes les exigences de I interf rence canadienne causant des r glements d quipement Lop ration est sujette aux deux conditions suivantes 1 ce dispositif peut ne pas causer l interf rence nocive et 2 ce dis positif doit accepter n importe quelle interf rence re ue y compris l interf rence qui peut causer l op ration peu d sir e O To comply with Fire Listed doors the batteries must be replaced with alkaline batteries only To avoid possible damage from electrostatic discharge ESD some basic precautions should be used when handling electronic components e Minimize build up of static by touching and or maintaining contact with unpainted metal surfaces such as door hinges latches and mounting plates especially when mounting electronic components such as readers and controllers onto the door e Leave components reader and controller protected in their respective anti static bags until ready for installation e Do not touch pins le
16. improperly door status monitoring features will not function Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 7 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock RGorbin za ASSA ABLOY 5 Installation Instructions Continued 4 Lock Handing Instructions a Move the Red locking screw to side of lock body being locked Fig 1 Catch Plate b Push in latch then depress catch plate with screw driver Fig 1 c Pull latch out of lock body and turn latch over Fig 2 RED Locking Screw Figure 1 MAKE SURE CATCH PLATE IS Figure 2 EVEN W TOP SURFACE d Push in latch while holding screw driver behind latch tail Fig 3 Note Push in latch until catch plate is no longer depressed Fig 4 e Rotate lock front to match bevel of door as shown Fig 5 WARNING LOCK IN CAN OCCUR IF LATCH IS NOT PROPERLY Figure 3 INSTALLED Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 8 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock Rgorbinyy ASSA ABLOY 5 Installation Instructions Continued 5
17. in part without the express written permission of Corbin Russwin Inc is prohibited 18 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock RgerbinyA ASSA ABLOY 6 Operational Check When lock is fully installed perform the following steps a Insert key into cylinder and rotate Fig 20a b There should be no friction against lock case wire harness or any other obstructions c Check that the key retracts the latch d The key should rotate freely e Try the inside lever ensure it retracts latch f Use a valid credential set up with the Lock Configuration Tool to unlock outside lever and retract latch Refer to Network and Lock Configuration Tool user manual WFMN1 for information on how to configure and program locks Twenty 20 seconds after lock initialization single beep with lock motor actuation Note The credential should approach the inscription on the reader as indicated Fig 20b to ensure that the credential is read properly Do not wave credential Fig 20b Copyright an oroin se me an ASSA ABLOY peop company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 19 ASSA ABLOY the global leader in door opening solutions R SWIN ZA ASSA ABLOY ASSA ABLOY is the global leader in door opening solutions dedicated to satisfying
18. nstructions this manual Pt Specify finish Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 4 ASSA ABLOY the global leader in door opening solutions IN120 Mortise Lock For parts not listed refer to ML2000 Parts and Service Manual 816F048 handing 26D ML20233 ML20234 Lock Case No Deadbolt not shown 816F058 handing 26D ML20235 ML20236 Lock Case With Deadbolt not shown 1 783F938 handing 26D ML20133 ML20134 Lock Case No Deadbolt il 783F948 handing 26D ML20135 ML20136 Lock Case With Deadbolt 783F619 DPS Door Position Switch Kit P Replace with handing L LR R RR Required for Escape Return functionality a residential requirement in Canada Copyright 2015 Corbin Russwin Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Corbin Russwin Inc is prohibited 5 ASSA ABLOY the global leader in door opening solutions RUSWANA ASSA ABLOY 4 Product Illustration Continued Tools Required e Phillips Screw Driver 2 3 e Flat Blade Screw Driver Standard size e 1 8 Security Allen Wrench supplied e 7 64 Allen Wrench supplied e Pin Hex Wrench supplied Wae
Download Pdf Manuals
Related Search