Coffee Maker Senseo HD7811/62
Contents
1. When the volume has to increase with 10 cc for example push the 2 cup button 3 times The new value will be stored when you switch the appliance off by pushing the main switch LED will turn off 11 Turn appliance on again and brew one cup measure the volume In case the volume is not within specification repeat steps 6 11 12 End 3 6 REPAIR INSTRUCTION Automatic filling procedure The Senseo PCB contains a automatic filling procedure software routine This fill routine is only meant for back up Normally the consumer has to follow the guidelines stated in the DFU The filling procedure functions as follows The consumer has to fill the water container and has to plug the appliance on the mains When the Senseo main switch has been pushed the main switch LED will light continuously This is only the case when the Senseo has not finished the filling procedure completely First use When the consumer pushes the one or two cup button the Senseo will start automatically the pump to fill the boiler When the boiler is filled the pump stops pumping Pump time approximately 22 seconds HD7811 62 Restoring the Boiler_empty_flag to production default Some times it is needed that the boiler of the Senseo have to be emptied This for instance in wintertime were the possibility exists that the boiler becomes frozen during transport e g For those occasions it is handy to restore the Boiler_empty_ flag aga2. 1 Be sure the boiler is filled properly other wise perform fill procedure see DFU for instructions 2 Switch appliance on and wait until the unit is ready to brew 3 Be sure a pod holder is placed but without a Coffee POD Only adjusting with plain water 4 Place a cup on the drip tray cover and push the one cup button 5 When the appliance has finished it is stabilized to perform the volume adjustment 6 Empty the cup podholder and push again for one cup setting measure the volume output with a graduated beaker In the table you can find the requirements for the minimum maximum volume output cc mL values depending from the country version One cup setting Including Pod holder water spec Without Coffee pod PT int acer 04 5 7 Unplug the appliance from the mains 8 Press the 1 and 2 cup button simultaneously and plug the mains on 9 When above step succeeded the led will turn on continuously 10 Depending if the volume has to de or increase you have to push the one or two cup button Every time you push the 1 or 2 cup button the LED will turn off for 0 5 second feedback to user and the pump time will be shortened or lengthened for 0 5 seconds depending which button was pushed Pushing 1 cup button pump time will be shorten with 0 5 sec is approximately 3 5 cc mL less coffee Pushing 2 cup button pump time will be lengthen with 0 5 sec is approximately 3 5 cc mL more coffee
3. see base and the housing can now be removed To remove the rest of the housing unlock the last 4 snap locks at the base and gently pull of the front cover To reassemble follow above steps backwards 2 6 REPAIR INSTRUCTION Descaling Descaling is an important element in Senseo maintenance It should be done at least once every 3 months up to 6 times a Year This will prolong the life of your appliance and will guarantee optimal brewing results for a long time Use the correct descaling agent Only citric acid based descalers are suitable for descaling the SENSEO machine This type of descaler descales the appliance without damaging it For the correct amount see under Descaling procedure below Each descaling mixture can be used only once After use the descaling mixture is no longer active We advise you to use the special SENSEO Descaler HD7006 Read the instructions on the package of the descaling agent Never use a descaling agent based on mineral acids such as sulphuric acid hydrochloric acid sulphamic acid and acetic acid e g vinegar These descaling agents may damage your SENSEO coffee machine e Follow the steps in the section headed Descale the appliance see DFU Direction for Use manual HD7811 62 Volume adjustment The PCB circuit board makes it possible to adjust the volume output by means of pushing the one cup and two cup user controls How to adjust the volume output
4. 270 Boiler assy TCO V7 0 230 V 14 4222 247 06511 Pressure hose Is 4222 259 34887 Base PCB assy basic 230 V 16 4222 247 05130 O ring NTC 17 4222 259 35500 NTC assy 18 4222259 44450 Water tank assy Spain Soft grey 4222 259 20100 XL 10 Cups Water tank assy Silent blue 19 4222 247 37200 Valve outlet Raven black 204222 255 36953 Back cover assy Raven black 21 4222 259 37240 Pump ULKA HF 230 V 50 Hz 22 4213 247 05250 Foot 23 4222 259 06105 Front Cover Raven Black 24 4222 247 39902 Button Frame Silver 25 4222 247 39913 On Off button 26 4222 247 39941 Button Cover Silver u changed 4 6 EXPLODED VIEW HD7811 62 EXPLODED VIEW HD7811 62
5. Coffee Maker Senseo Service HD781 1 62 Service Service Philips Consumer Lifestyle PRODUCT INFORMATION Water level Temp Sensor This product meets the requirements regarding interference suppression on radio and TV After the product has been repaired it should function properly and has to meet the safety requirements as officially laid down at this moment TECHNICAL INFORMATION a CONTROL Voltage 220 240 V m Frequency 50 60 Hz Power consumption 1450 W T Standby power consumption lt 1W Contents reservoir 750 cc Colour setting Raven black SAP coding HD7811 62 Push buttons OPTIONAL accessories XL watertank 10 Cups Commercial type number HD7982 Service code 4222 259 20100 Published by Philips Consumer Lifestyle Printed in the Netherlands Copyright reserved Subject to modification a PHILIPS DISASSEMBLY AND RE ASSEMBLY ADVISE Disassembly information To remove the brew chamber lid cover handle as follows Place the screwdriver on the positions see picture 1 and lift the cover over the snap locks on both positions The cover lid can now be lifted up a little and to remove the complete cover including lever and push rod squeeze strongly with two fingers both legs of the push rod see picture 2 to each other so that the two pins will get out of the hinge picture 2 position on the brew chamber To remove lever from lid cover take a sc
6. in to production default Bringing the Senseo back into production status has the benefit the flush routine will be activated automatically when installed by the consumer see topic Automatic filling procedure To SET the Boiler_empty_flag can be done by Keep the 1 cup button pressed while plugging in the power cord of the appliance The main switch LED will blink very rapidly for approximately 1 second To check if the Boiler_empty_flag is really set you should reconnect the power cord a second time to the net and push When the filling procedure has been successful the software will clear a Boiler_empty_flag in the Eeprom the main switch The main switch LED should light continuously By means of this Boiler_empty_flag the system knows the boiler is filled or not When the Senseo is switched off or disconnected from the mains the value of the Boiler_empty_flag is stored in the Eeprom chip PARTS LIST Pos Service code Description l 4222 259 44413 Brew chamber assy Spain Raven black 2 4222 259 44320 Padholder 1 cup low volume Black 3 4222 259 44330 Padholder 2 cup low volume Black 4 4222 247 39540 Foam chamber 5 4222 247 37140 Foam chamber cover Black 6 4222 240 06670 Drip tray cover 7 4222 247 35790 Drip tray 8 4222 247 35820 Push rod 9 4222 240 06400 Slider spring 10 4222 247 06810 Brew chamber radial seal 11 4222 259 06890 Distrubutor assy 12 4222 259 34970 3 Way valve assy 13 4222 259 44
7. rewdriver and bend carefully the two lips ribs in the lid cover outwards and push the lever with force out of the hinge Reassemble follow steps backwards without using a screwdriver To remove the back cover handle as follows Remove valve outlet Start at the upper side of the back cover and stick a screwdriver into the 2 snap locks positions and gently pull the back cover from the appliance so that a little chink between back cover and brew chamber becomes visible Put the screwdriver in to the 4 rectangular holes snap locks at the back and gently pull the screwdriver such away that the lips of the snap locks are bent outwards If all clicks positions are loose it is possible to remove the back cover Reassemble follow steps backwards HD7811 62 Removing Brew chamber head handle as follows Disassemble back cover Place the appliance such a way that you are looking at the boiler First remove the boiler from the snap lock position of the brew chamber To remove the brew chamber use your both thumbs see picture 3 and push strongly with a little distortion rotation until the brew chamber comes loose picture 3 Reassemble follow above steps backwards To reach the components placed on the base handle as follows First remove back cover brew chamber and 3 way valve Remove both Torx T15 screws see exploded view in the near of position A Bend the 2 click snap locks with a screwdriver
Download Pdf Manuals
Related Search