LO2B Versa Accent Lighting NEW MASTER
Contents
1. NOTE Apply masking tape as needed to surfaces to avoid scratches Riegner and Associates Inc Page 7 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 11 INTERIOR PREPARATION 13 Remove two 2 Phillips screws at the bottom of the instrument cluster 14 Remove the cluster by pulling it straight out to disconnect the clips at the top of the assembly 15 Rotate the instrument cluster upward and disconnect the white electrical connector from the back Set the instrument cluster aside Riegner and Associates Inc Page 8 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 11 INTERIOR PREPARATION 16 Carefully pull back the door seal welt from the footwell finisher to just past the A Pillar trim panel 17 Carefully remove the A Pillar trim panel NOTE There are two 2 retaining clips that hold the trim panel to the A Pillar along with a number of press clips Retaining clips Use a pair of needle nose pliers to remove the retaining clips and free the A Pillar trim panel Do not reuse these clips after removal Use the new clips provided in the kit Ss NOTE IF ANY CLIPS ARE DAMAGED OR LOST CONTACT DEALER FOR PART NUMBER 76988 J MOOA TO REPLACE Riegner and Associates Inc Page 9 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 12 POSI TAP INSTRUCTIONS 1 Ta2. 80 Peel the cover off the tape on the controller and place the controller on the carpet under the center stack Bundle and dress the excess cables from the cup holder and encoder switch only and secure with cable ties as shown NOTE Hold carpeting down when placing the adhesive tape to secure placement of the controller Riegner and Associates Inc Page 30 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 15 INSTALLATION Fig 81 81 Stow excess wire bundle behind center stack finishing panel Prepare To Install Driver s Side Light Stick 82 Using a metric scale or ruler measure and mark 50mm from the bottom edge Measure and mark 20mm from right edge of the DDL opening On the right side measure and mark 25mm from the bottom edge first then 10mm from the right edge Use a 3 16 inch drill and drill both locations DDL Opening Riegner and Associates Inc Page 31 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 15 INSTALLATION 83 Attach two 2 U Nuts to the small 80mm and 50mm L brackets at the long end L Bracket Exaggerated view of installing U Nut on L bracket 84 Attach the two 2 L brackets with U nuts to the inside of the steering finisher with two 2 phillips screws The 80mm bracket will be next to the DDL opening Fig 84 L Bracket 3 16 5 Remove ta
3. Accent Lighting Kit 15 INSTALLATION Encoder switch ig 59 Install the encoder so that the shaft is outside the front of the finisher panel Use 11mm nut to secure the encoder Install control knob over shaft of encoder Secure excess wiring with foam tape as shown NOTE Be careful NOT to over tighten the encoder nut Foam Tape 60 Reinstall the center stack bottom finisher panel Once aligned install two 2 plastic clip fasteners on either side 61 Carefully place the modified center console into the car Position the console over the parking brake and shifter by gently moving the console forward as it is lowered Route the wires from the cup holder LEDS and the encoder switch up through the center stack finisher panel and out towards the driver side footwell NOTE Be sure to feed the cup holder LED wires UNDER the duct tube assembly Riegner and Associates Inc Page 24 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 15 INSTALLATION 62 Once the console has cleared the parking brake and shifter pull back and set the console over the two rear retaining screw locations Reconnect one 1 electrical connector and the Accessory Power Outlet connector by reaching under from the back NOTE Be careful not to damage the headliner during reinstallation Slide both seats all the way forward at this time 63 If vehicle is equipped with
4. covers from the two 2 pieces of foam tape attached to the passenger light stick Place the light stick behind the lower glovebox cross bar with the LEDs pointing down Secure each the light bar with with three 3 4 inch cable ties at the drilled holes locations NOTE Be sure not to block the LEDs crossbar Reinstall the glovebox compartment Install four 4 phillips screws in the bottom of the glovebox compartment Install six 6 screws in the upper half of the glovebox compartment Reinstall the glovebox door by carefully snapping the door onto the lower hinge and the side support arms back into both slots Riegner and Associates Inc Page 29 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 15 INSTALLATION NOTE Attach 1 58mm x 82mm foam tape to the underside of the accessory control module covering the screw in the center 77 Place one 1 piece of foam tape over the top of the accessory controller It should be on the opposite side of the sticky foam tape covering the screw NOTE Do NOT pull cover off tape on Fig 78 controller at this time DY lt AN Secure the harness under the dash Cable tie with cable ties as shown lt gt Wi Route accessory harnesses under the center stack Plug the accessory harnesses into the control module and allow to sit under center stack Driver Side Footwell
5. steering finisher down away from the instrument panel Pry the left side away first then the right side NOTE Apply masking tape as needed to surfaces to avoid scratches 5 Disconnect two 2 electrical connectors from back of panel 6 Remove the steering finisher and set aside Riegner and Associates Inc Page 5 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 11 INTERIOR PREPARATION 7 Carefully pry off center stack upper trim panel Follow the pry off sequence 1 2 and 3 as shown NOTE Apply masking tape as needed to surfaces to avoid scratches 8 Disconnect two 2 electrical connectors behind trim panel and set panel aside NOTE Turn the car ignition On and rotate steering wheel 90 degrees to the right 9 Remove one 1 phillips screw from behind steering wheel on the right Riegner and Associates Inc Page 6 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 11 INTERIOR PREPARATION NOTE Rotate steering wheel 180 in the opposite direction 10 Remove one 1 phillips screw from behind steering wheel on the left 11 Turn the car ignition to Off position Carefully pry off the trim panel from the top half of the steering column and set it aside NOTE Apply masking tape as needed to surfaces to avoid scratches 12 Carefully pry off the instrument cluster trim panel and set it aside
6. the instrument cluster trim panel Riegner and Associates Inc Page 17 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 13 INSTALLATION 42 Reinstall the trim panel on the top half of the steering column Reinstall two 2 phillips screws on both sides of the steering wheel NOTE Rotate steering wheel 180 in the both directions to access the screw mounting holes 43 Reconnect two 2 electrical connectors behind the center stack upper trim panel 44 Reinstall the center stack upper trim panel Riegner and Associates Inc Page 18 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 14 INTERIOR PREPARATION 45 Open the glovebox door Remove four 6 screws from the upper half of the glovebox compartment as shown Press down firmly on the glovebox door side supports to release them and then unsnap the door from the lower hinge Set the glovebox door aside 47 Remove two 2 plastic clip fasteners on either side of the center console NOTE Slide both seats fully forward and pull emergency brake handle all the way up at this time Riegner and Associates Inc Page 19 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 14 INTERIOR PREPARATION 48 Remove two 2 T 20 Torx fasteners at the back of the center console on both sides Note the location of the two 2 harn
7. GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION Accent light Kit 2 APPLICATION Versa 2012 3 PART NUMBER 999F3 008 Universal Accent Lighting Kit 4 KIT CONTENTS Description module ncoder and harness assembly oot well lights and harness assembly up holder lights and harness assembly Harness Vehicle interface Control Knob Kit contents in back of Installation Instructions ee te ae Tether Clips N Rll Rye lt TOOLS REQUIRED Trim stick e Ratchet and 6 extension e 8mm 10mm and 11mm sockets 5 16 3 16 and 9 32 drill bits drill drill stops e 2 Phillips screwdriver e T 20 Torx bit e Protective cloth e Scissors e Needle nose pliers e Electrical tape masking tape PRE I NSTALLATI ON CAUTI ON NOTES e Dealer installation recommended Instructions may refer to Service Manual e Installation may require special tools e This part is to be installed at a surface temperature no warmer than 65 100 F e Remove and prepare templates located at the end of Installation Instructions e All electrical connectors are to be viewed from wiring side as shown CAUTION e This accessory must only be installed as specified in these instructions e Ensure at all times that parts are securely fitted and will not compromise the safe function of vehicle systems Riegner and Associates Inc Page 1 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTION
8. INSTRUCTIONS Accent Lighting Kit 13 INSTALLATION 18 Push the ends of 2 wires green and blue through the end of a 15 inch cable tie and use the tie to direct the wires up through the dash to the BCM opening Be sure to route the wires all the way up to the BCM opening Riegner and Associates Inc Page 11 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 13 INSTALLATION CAUTION e Color s given in illustration s are for reference only Use location s where color deviates e Ifa vehicle wire is being used by another accessory and posi Tap is present tap the accessory wire NOT the vehicle wire NOTE Two different types of meters are available on this vehicle Verify which one you will be working with to accurately tap the harness wiring NOTE Visually identify the Grey and Red S Grade wires in the harness before proceeding Meter Pinouts MAIN H METER TH4OFW NH TYPE AB R a ee O won 0 TH4OFW NH NOTE Disconnect negative battery terminal before proceeding 20 Carefully strip back some of the insulation from the white instrument cluster connector Identify the Grey and Red wires Use a Posi tap and instructions to connect the Blue wire from the accessory harness to the Grey wire at the connector Blue Wire Use a Posi tap and instructions to connect the Green wire from the accessory harness to th
9. S Accent lighting Kit 7 INSTALLATION OVERVIEW Power Cable Junction Box CRITICAL STEPS The following steps are critical and must be performed EXACTLY as specified to ensure proper installation Location of the lights must be followed exactly as described in this instruction Posi Tap instructions must be specifically followed as described Riegner and Associates Inc Page 2 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 9 VEHICLE PREPARATION Apply parking brake Confirm the vehicle is no longer in the default shipping state Extended Storage Switch Pulled Up and BCM in Transit Mode Failure to confirm the vehicle has been removed from this state will result in the loss of normal vehicle operation The confirmation requires two checks 2a Locate the Extended Storage Switch 2b Turn the ignition switch from OFF to ON position If in the cabin fuse block Once located turn indicators illuminate for approx 1 minute the check that it is in the Customer vehicle is in shipping mode To exit shipping mode position See below for reference return the ignition switch to OFF position Simultaneously push the wiper and turn signal stalks downward and hold for 2 seconds Inventory Customer PULL UP PUSH DOWN INCORRECT NOTE Typical vehicle condition shown here Switch is easily identifiable by the permanent push pull fuse holder Actual p
10. ack 2 Cable tie 11 Black 2 141 Cable tie 4 Black 4 Grey foam rectangle 80mm x 30mm 5mm Adhesiveoneside 61 5 Small bracket 28mm long 6 Medium bracketS4mmiong fa 14 7 targe bracket 80mmiong 8 Posi tap connector Red Grey dT 991 TOO 9 Control knob Black white printing if 999 3 2 20 Alcohol preparation wipe fa 51 12 Module adhesive fixing 53mm 74mm fa 13 Lens Retaining Ring 9mm OD Black e 14 Clear plasticlens 7 5mmdiameter 15 Pozi drive self tap screw 1 2 long Black 216 Encoder lockout a 94 18 Double sided adhesive fixing 12mm 20mm one backing paper fa 19 Double sided adhesive fixing 12mm x 102mm Allon backing paper a Not In Installation Kit bag 1 Riegner and Associates Inc BOM 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit Versa Mechanization S GRADE Footwell Light Sticks oat 4 H NIVW Accessory O Controller gt AH gt 7 qn gt gt Cup Holder Light Stick d fom om nero THO amp SMW NH MALE SIDE Riegner and Associates Inc S Mechanization 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Ac
11. cent Lighting Kit Versa Mechanization SV amp SL GRADE Footwell Light Sticks fejen pts ae O Controller METER i pec gt z x z gt gt x TH4OFW NH Cup Holder Light Stick ddj dj y THO8MW NH MALE SIDE Riegner and Associates Inc SV SL Mechanization 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit Templates must be printed to scale 2 0 65 LO2B CUP HOLDER TEMPLATE POSITION TOWARDS REAR Riegner and Associates Inc Template A 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit Templates must be printed to scale LO2B ENCODER TEMPLATE Riegner Associates Inc Template B 999F3 008 II Rev 6 10 2011
12. e Red wire at the connector S Grade Riegner and Associates Inc Page 12 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 13 INSTALLATION NOTE Visually identify the Grey and Red wires in the harness before proceeding SV amp SL Grade Meter Pinouts METER TH4 NH TYPE C AIN OFW METER NOTE Disconnect negative battery terminal before proceeding 22 Carefully strip back some of the insulation from the white instrument cluster connector Identify the Grey and Red wires Use a Posi tap and instructions to connect the Blue wire from the accessory harness to the Grey wire at the connector SV amp SL Grade 23 Use a Posi tap and instructions to connect the Green wire from the accessory harness to the Red wire at the connector SV amp SL Grade Riegner and Associates Inc Page 13 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 13 INSTALLATION aS Fig 24 24 Use a long cable tie to feed the 2 Brown wire Brown accessory wire through the xs A opening and out the dash opening under N Bo the vent as shown bps RAD Ve mail Feed a 15 inch cable tie down through the dash from the A Pillar Push the ends of the Brown wire through the end and use the tie to direct the wires up through the dash to the A Pillar 26 Disconnect the electrical connector at the bottom of the A p
13. ess clips under the center console NOTE Turn ignition to ON position Press on brake and pull shifter back to position Turn ignition off 49 Loosen the center console by lifting the front slightly then lift the back Release two 2 harness clips at metal studs Disconnect one 1 electrical connector and the Accessory Power Outlet connector by reaching under from the back Riegner and Associates Inc Page 20 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 14 INTERIOR PREPARATION MANUAL SHIFTER ig 50 If vehicle is equipped with manual shifter remove the shifter boot by carefully stretching the elastic collar up over the shift knob 51 Carefully remove the center console and set it aside NOTE Be careful not to damage the headliner during removal Slide both seats all the way to the rear at this time 52 Remove two 2 plastic clip fasteners on either side of the center stack bottom finisher panel Riegner and Associates Inc Page 21 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 14 INTERIOR PREPARATION 53 Remove the center stack bottom finisher panel and set aside 15 INSTALLATION 54 Place center console assembly upside down on work surface Be careful not to scratch the surface NOTE Print all templates at actual size 55 Trim out template A and tape into place over the bottom of the fo
14. illar Carefully strip back some of the insulation from the upper half of the connector and identify the Red wire NOTE Trim excess wire down to appropriate length before attaching Posi taps Riegner and Associates Inc Page 14 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 13 INSTALLATION Using a Posi Tap connect the Brown wire from the accessory harness to the Red wire at the connector Reconnect the two A pillar connector halves THOSMW NH To Accent Lighting Controller Brown wire Module LGO2 LG11 MALE SIDE MAIN_H THO8MW_NH RM_LAMP_H MAIN H 29 Remove one 1 10mm bolt on the left side of the knee bolster bracket under the steering column Place the bolt through the eyelet on the Black accessory wire for ground Reinstall the bolt NOTE Wrap wire with foam tape as shown to protect from sharp metal edges Work the tilt wheel adjustment up AO Bolt and down to be sure there is no binding at the harness Riegner and Associates Inc Page 15 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 13 INSTALLATION BEFORE REASSEMBLING VEHICLE S TRIM PANELS 30 Plug all components together temporarily for functionality test NOTE Refer to Mechanization diagrams on last page if necessary 31 Reconnect the white electrical connector at the back of the instrument cluster 32 Turn the vehicle ignitio
15. manual shifter reinstall the shifter boot by carefully stretching the elastic collar down over the shift knob 64 Reinstall two 2 harness clips at metal studs Reinstall two 2 T 20 Torx fasteners at the back of the center console on both sides Harness B clip Slide both seats all the way to the rear at this time Riegner and Associates Inc Page 25 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 13 INSTALLATION 65 Reinstall two 2 plastic clip fasteners on either side of the center console 66 Remove four 4 Phillips crews from the bottom of the glovebox compartment NOTE Two of the screws are behind cover panels 67 Grip the door latch loop and pull down and outward to remove the glovebox compartment Set the compartment aside NOTE Apply masking tape as needed to surfaces to avoid scratches Riegner and Associates Inc Page 26 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 15 INSTALLATION GLOVEBOX CAVITY Left Hole Right Hole Location Location crossbar Passenger Footwell 68 Prepare to mark drill locations at the glovebox opening Measure and mark in from the back edge 7mm Mark the left and right mounting holes centered in alignment with the two existing holes on the lower cross bar as shown Carefully drill a 3 16 inch hole at both locations NOTE Do NOT drill past the bott
16. n switch to the ON position push the lighting control knob and confirm the Accent Lighting illuminates 33 Turn the lighting control knob and confirm that the color changes through 20 variations 34 Press and hold the control knob for 3 seconds and confirm that the Accent Lighting enters the Demo Mode and cycles through colors Press knob again to exit demo mode Leaving the accessory ON turn the Interior Room Lamp to DOOR and ignition switch OFF Open the door and confirm the Accent Lighting illuminates Leaving the accessory ON and the ignition switch OFF close and lock the door using CDL or Key Fob if equipped Confirm that the Accent Lighting turns off Disconnect all components and proceed with installation 38 Reinstall the A pillar trim panel NOTE There are two 2 retaining clips that hold the trim panel to the A Pillar along with a number of press clips DO NOT REUSE THE CLIPS THAT WERE REMOVED EARLIER INSTALL THE NEW CLIPS PROVIDED IN THE KIT IF THE CLIPS ARE DAMAGED OR LOST CONTACT DEALER FOR PART NUMBER 76988 MOOA TO REPLACE Riegner and Associates Inc Page 16 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 13 INSTALLATION 39 Reinstall the door seal welt Do not pinch the welt by the Instrument panel 40 Reinstall the instrument cluster and the two 2 Phillips screws at the bottom of the instrument cluster 41 Reinstall
17. om rib Use a drill stop set to 4mm DRIVER SIDE 70 Prepare the driver side light stick Clean the LED areas with alcohol wipe Fix the short 12 5mm X 19mm X 7mm piece of double sided foam tape at location 1 75 to 2 5 AND at location 11 5 to END NOTE Be sure not to block the LEDs Riegner and Associates Inc Page 27 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 15 INSTALLATION PASSENGER SIDE Fig 71 8 22 1 71 Prepare the passenger side light stick Clean the Non LED areas with alcohol wipe Fix the long 12 5mm X 100mm X 7mm piece of double sided foam tape at location 0 5 to 4 5 AND at location 8 to the END 72 Push the passenger light stick through the center stack to the passenger footwell This is the light stick with the loop NOTE The driver s side light stick should be left in the driver s footwell for later installation Brake Pedal On the passenger side Insert a cable tie in each mounting hole as shown Cable ties Hold the passenger side light stick up to the cross bar to get a visual aligment before final mounting The holes should align with the 4 and 8 5 marks Riegner and Associates Inc Page 28 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 15 INSTALLATION Cross section ig 74 Pull the tape
18. osition on the fuse block may vary vehicle to vehicle 3 Record customer radio presets NOTE USE CAUTION WHEN REMOVING RE I NSTALLI NG TRIM COMPONENTS TO AVOID DAMAGE SCRATCHES BREAKING OF CLIPS AND OR INTERIOR TRIM PANELS MOVE ALL TRIM COMPONENTS TO A PROTECTED AREA The battery is left connected as various parts of the car need to be moved to enable components to be removed and replaced Use caution when activating parts of the car ORDER OF INSTALLATION Interior preparation remove panels Reinstall Glove Box and Footwell trim Install Cup Holder installation Install Vehicle interface Install Encoder Install Driver Footwell light Reinstall Center Console System check Install Passenger Footwell light 0 Reinstall Remaining Panels Riegner and Associates Inc Page 3 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 11 INTERIOR PREPARATION 1 Carefully remove the LH Instrument side mask by the driver s door 2 Remove two 2 10mm bolts under the hood release lever Remove the hood release lever assembly 3 Remove one 1 phillips screw holding the diagnostic port to the panel Note Place your hand behind the panel to hold it as it is unscrewed Riegner and Associates Inc Page 4 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 11 INTERIOR PREPARATION 4 Carefully pull the
19. p vehicle wire a Remove cap slot side from tap body b Slide cap around vehicle wire c Tighten the tap TIGHT with finger pressure NOTE Do not re use the tap for subsequent re installation Figures are not to scale 2 Inspect the tap to ensure correct installation NOTE Avoid putting pressure on the vehicle wire and tap for the remainder the as installation i Straight and evenly spaced all the way around ii Tight and minimize gap wire jacket should be crushed 3 Inspect the tap to ensure correct installation a Remove tap non pierce side from tap b Remove the protective stub from the wire c Insert wire through the non pierce side opening d Spread the individual strands into fan shape e Insert wire into the tap body and ensure that it is all the way in f Tighten the tap TIGHT with finger pressure Confirm the tapped accessory wire a Inspect the tap to ensure correct installation Straight and evenly spaced all around b Test the signal to ensure that it is ii Tight and gap and test the signal working properly Secure the tap a Secure the tapped wire on the non pierce side to the body of the tap with electrical tape 2 2 revolutions b Secure the body to harness where vehicle wire is being tapped with electrical tape 2 2 revolutions Accessory harness Riegner and Associates Inc Page 10 of 34 999F3 008 II Rev 6 10 2011 INSTALLATION
20. pe liner Steering finisher Riegner and Associates Inc Page 32 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 15 INSTALLATION 85 Work on the steering finisher in the driver s floor area Clean mounting area with alcohol wipe Peel tabs away from the adhesive tape Place the light stick so that the foam tape lines up with the metal brackets as shown Note Be sure not to block DDL opening Cable Ties 50mm Bracket 80mm Bracket 86 Pull the tape covers from the two 2 pieces of foam tape attached to the driver side light stick Place the light stick over the L brackets with the LEDs pointing down such that the tape rests on the L bracket Secure each location with two 2 4 inch cable ties Note Trim the cable ties and turn them inwards so the clipped end is on the inside of the panel Reinstall the diagnostic port to the steering finisher panel with one 1 phillips screw Reconnect two 2 electrical connectors at back of panel Reinstall the steering finisher panel Reinstall the hood release lever assembly using two 2 10mm bolts Reinstall the driver side instrument side mask Note Trim all cable ties Check installation Riegner and Associates Inc Page 33 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 16 CHECK OUT 1 Open the rear storage area of the center console 2 Turn the vehicle igni
21. rward cup holders as shown The template should be positioned with the two hanging tabs toward the back Mark and drill two 2 9 32 inch holes at the locations indicated on the template Remove the template Clean any flashing from holes Install two 2 LED lenses through the holes with the black retaining collar on the inside of the cup holders Riegner and Associates Inc Page 22 of 34 999F3 008 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 15 INSTALLATION Clean the light stick mounting area with alcohol Remove the pull tabs over the tape on the end cup holder light stick Place the light stick over the black lens retainer as shown Remove the pull tabs over the tape of the second cup holder light stick the one with wires at each end and place the light stick over the black lens retainer as shown 57 Secure excess wiring with foam tape as shown Foam Tape Place center stack bottom finisher panel face down on work surface Be careful not to scratch the surface Trim out template B and tape into place inside center of panel as shown The template should be positioned with the letter in the upper right hand corner Mark and drill one 1 5 16 inch hole at the location indicated on the template Remove the template Clean any flashing from the hole Riegner and Associates Inc Page 23 of 34 999F3 AWO08 Rev 6 10 2011 INSTALLATION INSTRUCTIONS
22. tion switch to the ACC position push the lighting control knob and confirm the Accent Lighting illuminates 3 Turn the lighting control knob and confirm that the color changes through 20 variations 4 Press and hold the control knob for 3 seconds and confirm that the Accent Lighting enters the Demo Mode and cycles through colors Press knob again to exit demo mode 5 Leaving the accessory ON turn the Interior Room Lamp to DOOR and ignition switch OFF Open the door and confirm the Accent Lighting illuminates 6 Leaving the accessory ON and the ignition switch OFF close and lock the door using CDL or Key Fob if equipped Confirm that the Accent Lighting turns off 7 Reset the radio presets to the recorded settings 8 Place the Accent Lighting Quick Reference card in the glovebox 9 Check the trim for a proper flush fit after re installing the interior components 10 Clean the interior of the vehicle 11 Inspect the vehicle interior and exterior for damage 12 Verify the functionality of all electrical vehicle components where harnesses were accessed 13 Check and clear trouble codes DTC Riegner and Associates Inc Page 34 of 34 999F3 AWO08 Rev 6 10 2011 INSTALLATION INSTRUCTIONS Accent Lighting Kit 17 BILL OF MATERIALS Nissan Universal Accent Lighting Kit 999F3 008 _ Parts Contained Bag Labeled Installation Part Number Cable tie 15 Bl
Download Pdf Manuals
Related Search