Haier WASHING MACHINE
Contents
1. A Wash programming knob By turning the knob clockwise counterclockwise the required program can be selected There are 11 programs available After a program is selected the cor responding light will go on Refer to Guide to Operational Program Selection B Power Switch Press this button to switch on the washing machine Press it again to switch it off C Start Pause Button When the washing machine is connected to the power socket and a program is selected washing operation will start Lightly touch this button during a wash cycle operation will stop and the digits on the screen start blinking Touch it again to resume operation To cancel a wash program during a wash cycle touch this button when the digits on the screen start blinking press the Power switch the program will be cancelled D Spinning Speed Setting Button Touch this button lightly to select the desired speed When a speed is set it will be displayed on the screen Note Different water temperatures and spinning speeds can be set for different laundries Refer to the operation instructions on pages 11 and 14 Wash using the default settings if there is no special requirement E Washing temperature button Touch this button lightly the washing temperature will be displayed on the screen Select a temperature according to the type of laundry Page 13 Haier Front Load Washing Machine Model HMS1OOOTVE Functions F Delay Button Touch this butt2. properly Please reconnect it or replace it Front Load Washing Machine Model HMS1000TVE Error message Motor overheat protection or damaged Troubleshooting Cut off power and check if motor wires Reconnect well are connected well Put the motor in normal temperature about Measure if resistance of motor winding by Te See Ti ten minutes and then test again If the multimeter is it as followed 1 2 5 resistance is natural it is caused by 3 5 5 7 8 5 overheated protection Then check and deal with overload abnormal voltage If not please replace motor Pull out the wire connection of motor Then check if circuit 1s open by multimeter Repair wires Page 19 i Front Load Washing Machine Model HMS1000TVE Error message Water level exceeds protective value Troubleshooting Clean water switch hose and air Check if water switch hose and air collector collector are jammed N Pull out water switch inserts and turn on power then set wash mode While water is entering at the position of 1 4 glass window check the resistance between and is it 0 Check the resistance between and isit infinite Replace water pressure switch N Without power connect inlet pipe to inlet Replace inlet valve vavle then open the tap and observe if water is entering in dispenser Replace Without starting but electrifying measure the zn import voltage of inle
3. phenomenon resulting from water test in the factory Fig 1 Dismantle the packing bolts as shown in Fig 2 The packing bolts are designed for clamping anti vibration Components inside of the washing machine during the transportation process Beforeuse 1 Remove the back plate 2 Remove the three packing bolts on the back plate and take out the rubber hose 3 Replace the back plate 4 Fill the holes left by the packing bolts with plastic plugs Attention The packing bolts and rubber hose should be kept ina safe place for later use Adjusting the washing machine There are adjustable feet under the bottom of the washing machine Before use the washing machine should be adjusted as shown in Fig 3 so that it is level Page 9 Haier Front Load Washing Model HMS1000TVE Installation Joining the Inlet Hose to the Washing Machine L inlet Es out 1 Connect the nut on the inlet hose to the connector on the water valve 2 Tighten the nut to secure the hose S Connect of water inlet valve The height of the drainage outlet must be 80 100cm To prevent the drainage hose from dropping off fix it to the drainage hose clip at the back of the washing machine e Use the drainage holder to keep the end of the drainage hose retained and to prevent the outflow of water It is recommended that drainage hose extensions not be used if a
4. Front Load Washing Machine Model HMS1000TVE Haier FRONT LOAD WASHING MACHINE Service Manual er mag Suited model HMS1000TVE Features 300mm diameter porthole door may be open at a 180 degrees Class A energy saving Homocentric tubs with higher energy efficiency Multi gear speed controller Unique gasket design featuring no residual water hidden inside Delay time adjustive Large wash load capacity 5kg Europe standard ABC Serial Number SM HMS1000TV01 Version 1 00 Edition 2007 2 Haler Front Load Washing ModeHMSTOOOTVE 1 Contents 1 2 Product code illumination and series introduction 2 3 Features 3 4 Specification 4 5 Safety 6 6 Installation 9 7 Net dimension 11 8 Names of the parts 12 9 Operational functions 13 10 Prog
5. d When the main wash valve allows water to let in for 3 seconds 77 77 will be dis played When the pre wash valve allows water to let in for 3 seconds 77 77 will be dis played When the hot water valve allows water to let in for 3 seconds 77 77 will be displayed When the main wash valve the pre wash valve and and also the hot water valve allow water to let in for 3 seconds at the same time 77 77 will be dis played When the motor runs for ten seconds with the spin speed 93rpm 66 66 will be dis played When the motor runs for 50 seconds with the spin speed 800rpm 66 66 will be displayed When the main wash and pre wash allow the water to go in meanwhile until the maxim water level 55 55 will be dis played When the water fills the tub fully it will stop for ten seconds and at this time 55 55 will be displayed When the motor runs clockwise for 15 seconds with 50 rpm the washing machine will stop for 5 seconds and at this time 44 44 will be displayed When the washing machine heats water for 10 seconds 33 33 will be dis played When the washing machine drains for 30 seconds 22 22 will be displayed When a program cycle is finished END will be displayed Haier FrontLoaa washing Machine ModetHIMSTOOOTVE Sincere Forever Haier Group Haier Industrial Park No 1 Haier Road 266101 Qingdao China http www haier com Page 30
6. d Y big eye Q R square Diameter cm 30 Outer door frame S stainless steel M p metal P plastic Inner door G glass P G plastic Detergent compartments n 3 Removable compartment for liquid detergent Page 4 u 7 Ha lef Front Load Washing Model HMS1000TVE Delay timer from to h 0 5 24 Self cleaning suds pump 2 Water inlet hose Water drain hose Adjustable feet n 4 Auto door lock Motor overheating protection No heating without water Auto water cool down before drain 80 C boiled water Water return protection Acqua Stop kit Child protection 1 Strong action cotton cycles 2 Normal action synthetics 3 Delicate action wooll cycles Pre wash wash Quick wash super quick wash Rinse soften Delicate hand wash Wool cashmere Soak spin Drain Easy ironing ON OFF button Half load Fussy Spin exclusion Spin speed selection High water level No Soak Rinse stop Delicate Cold wash Delay Timer Extra Rinse Load Select Easy Ironning Temperature selection okg wash Prewash REMAK Signify the washing machine has this function e Signify the washing machine doesn have this function Page Halef From Load Washing Machine Model HMS1000TVE Matters Needing Attention A separate earthed socket is required for the 2 Hold the plug and not the electric cable power supply The washing machine must be when unplugging the washing mac
7. d board Page 3 Ha ier Front Load Washing Machine Model HMS1000TVE SPECIFICATION Proposal 2006 HMS1000TVE Description of appliance Type of appliance FS standing BI built in Supplier own brand Supplier bar code Mares computer code Commercial Brand Model Commercial bar code Energy efficiency class en Washing performance class Spin efficiency class Programs Capacity Max 5 Spin speed max optional 1000 0 Noise level 71 Energy consumption per wash circle 0 95 Water consumption lt 49 Residual dampness spin result Spin speed selector switch steps 1000 800 600 400 0 Spin speed variator stepless Adjustable thermostat water temp adjust from Washing machine FS Haier to 80 amp Drum capacity dry laundry water 5 49 Auto water level adjust depending on volume of filled in laundry Washing time max 124 TBC Washing temperatures program controlled 30 40 60 80 Certification s CE 1SO 9001 ISO 9002 CE ISO 9001 Approvals VDE GS TUV GS IMQ TUV GS Rhl EN 60456 60 C cycle full load without pre wasn COLD Unit dimensions Net weight Kg 64 Voltage frequency V Hz 220 240V 50Hz Input power main fuse intensity WIA 1850 10 Work top removable Control M electromechanical E electronic E F fuzzy Drum S stainless steel Z zinc coated S Tub P Polyprop S stainless steel P Door aesthetic R roun
8. ecommended Temperature 9 Laundry 1 2 3 a Cold 30 Cold 30 Cotton Cotton fabrics ie 60 80 O eeu Fast color synthetic PEF or O Wool Woolen fabrics Cold 30 40 O hmer Silk Silk fabrics Cold 30 40 O Medium soil Medium soil Cold 30 Wash laundry 40 60 xX laundry Drain X X X Note O indicates that softener can be added if needed x indicates that detergent must be added X indicates that detergent must not be added 1 The wash temperature refers to the maxinum temperature 2 The wash cycle times are intended as a guide only The actually used time may vary due to different water pressure initial water temperature etc Page 15 Haier Front Load Washing Machine Model HMS1000TVE HMS1000TVE Error Display and Troubleshooting Error message Door is not properly shut 20s after program is started Troubleshooting Pushing the door to Check Whether Door is properly shut or not Shut the door properly Cut off the power and then turn on again 220 240v Check the voltage between brown wire and Door lock is broken and need blue wire of door lock is it between AC 220 240V replacing then make sure wire is connected properly Check if the wire connecting door lock Connect the wire properly and PCB is loose 220 240v Replace Check the voltage between brown wire and blue wire of PCB is it between AC 220 240V Error message Drainage error water not emptied within 4 mi
9. hine positioned so that the plug is accessible 3 Fuses in the power circuit should be rated for 15A 4 Do not touch or use the washing machine bare footed or when the hands or feet are wet If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard N o 5 Do not use flammable detergent or dry clean 6 The door of the washing machine will become hot ing agent do not use flammable spray in during the heating process Avoid contact with the close vicinity to the washing machine do not door during the heating process For safety keep remove or insert the plug in the presence of children away from the washing machine flammable gas Page 6 Haier Front Load Washing Model HMS1000TVE Matters Needing Attention The washing machine should not be install 9 The carpet must not obstruct the ventilation ed outdoors or in a damp place In the openings in the base of the washing machine event of water leakage or splashes allow the machine to dry naturally 10 Keep away from heat sources and direct sun 11 During installation ensure that the electric light to prevent plastic and rubber components cable is not trapped by the washing machine from aging and avoid damage to the electric cable Before use check the joints of the filling hose the Keep the door slightly open when the washing machine is not in use to prevent for
10. infinite Replace PCB Error message The heater may be broken Troubleshooting Check if overload of laundry Reduce the laundry Cut off power check the resistance of two pins of heater element by multimeter is it between 32 35 Heater element must be broken please replace it The control wire may be broken otherwise PCB must be broken Please replace the broken one Page 17 i Front Load Washing Machine Model HAS1000TVE Error message The required water level is not reached within 8 min Troubleshooting Check if water is leaking from washer bottom inlet pipe drain pipe or other pipe connection Check if tap is closed or water pressure is too low usual between0 3 1 MPa Check if inlet valve is jammed Draw out the dispenser and check if water is entering Turn on power and set pre wash mode then start Check the import voltage of electromagnetic valve by multimeter is it between AC 220 240V Check f export voltage from PCB to electromagnetic valve is it between AC 220 240V Replace PCB Page 18 Readjust or replace the broken parts Open the tap or wait for normal water pressure to use Clean inlet valve Observe if the height of drain pipe not reach 80 cm If water level pressures switch and the hose is leaking gas Electromagnetic valve must be broken please replace it The wire connected PCB and inlet valve is not
11. l ti pin of electromagnetic valve Page 21 Front Load Washing Machine Haier Failure no draining Troubleshooting Is the height of drain pipe too high Turn filter anticlockwise open and check if filter is jammed Check if hose connecting cylinder to pump is bent or jammed Turn on power and choose spin program to start Measure if import voltage of drain pump is 220 230V Cut off and check if the connection between drain pump and PCB is open Replace Turn on and choose spin program to PCB start Measure if export voltage of PCB to drain pump is 220 Failure abnormal noise and vibration Troubleshooting Is the pack screws dismantled Is there foreign material in the washer Is washer in balance Is belt loose or worn Are the screws of counterweight and motor loose Remove belt and turn belt pulley by hand and then check if there is different Turn on power and set spin program then start check if there is different noise from motor Page 22 Model HMS1000TVE Adjust the height of drain pipe to 80 100 cm Clean and tighten filter clockwise Arrange hose and clean Replace drain pump Replace the wire Dismantle the screws i Adjust adjustable feet Dismantle triangle and check the bearing If it is broken replace it Replace motor li Front Load Washing Machine Model HMS1000TVE Failure water leaking Troubleshooting Check if wa
12. mation of tap and the drainage hose for possible problems odors do not cover the washing machine with from water pressure fluctuations If joints are loose is ne so that inside dampness cannot or there is leakage turn off the tap and repair Do not use the washing machine until the hoses are properly fixed Page 7 Matters Needing Attention 3 Do not place heavy heating source or wet 4 Do not hot wash foam rubber or sponge like materials articles on the top of the washing machine 9 Before washing do up zippers buttons and 6 Do not open the detergent distribution drawer during the wash cycle clothes straps and put small articles such as socks laces or bras into a washing bag or a pillow Steel wires in bras will pop out during washing never wash bras containing steel wires 7 The door is fitted with a sel ock device and will notopen untl 8 After each wash program turn off di ap to l prevent leakage and unplug the washin 2 3 minutes after the washing machine stops Do not force machine and wipe clean the lower part o the door open Do not open the door if water level can reach the porthole the porthole Page 8 Haier Front Load Washing Machine Model HMS1000TVE Installation Remove all the packing materials including the foam base to prevent vibration during use as shown in Fig 1 Upon opening of the package water drops may be seen on the plastic bag and the porthole This is normal
13. n Troubleshooting Cut off power and water level pressure switch wire connection measure the resistance of 1 and 3 pin is it infinite If not it is water level pressure switch failure and replace it If it is then repair and check PCB and wire as followed Check if water is emptied Check if drain pump or drain pipe is jammed and open the filter and clean Check if drain pump acts by touching pump position Cut off the power and choose spin program to start then check the import voltage of drain pump is it between AC 220 240 V Replace drain pump The wire between PCB and drain pump is not connected properly Replace the wire Cut off power and pull out water level pressure switch wire connection Set spin program to start Check the export voltage to drain pump is it between AC 220 240V Replace PCB Page 16 Front Load Washing Machine Model HMS1000TVE Error message Temperature sensor is not properly connected or damaged display at the end of a program Troubleshooting Cut off power and measure the resistance l SR p NTC exist open circuit Replace it of temperature sensor by multimeter is it between 5 14k Y Check if NTC is connected properly Connect NTC well Check the wries of NTC are they connected well Connect all wires well Disconnect the white wire and black wire from PCB and measure if the resistance Replace wire between white wire and black wire of PCB is it
14. n extension is needed please consult a serviceman The additional hose should be no more than 250cm overextended hoses could lead to siphonage Note The drainage hose should not be submerged in water and should be securely fixed and leak free The appliance is to be connected to the waster mains using new hose sets and that old hose sets should not be reused Connecting to the Power Supply Before connecting to the power supply check The socket is adequate for the maximum power of the washing machine For safety fuses in the power circuit should be rated for no less than 15A The voltage should meet the requirement The power outlet should be capable of accepting the washing machine plug The washing machine must be earthed before use Supplementary earth cable should not be necessary if the socket is connected to the earth Supplementary earth cable shoulde be installed on the upper back of the washing machine andconnected to an earth if the power supply socket has no earth connection Page 10 Pr Front Load Washing Model HMS1000TVE Net Dimension 850 height 850mm width 595mm depth 520mm Page 11 Bu Front Load Washing Model HMS1000TVE Name of the parts Detergent dispenser Top Cover Button Program selector Door handle Porthole Bottom plaque Page 12 j ler Front Load Washing Model HMS1000TVE Opertional Functions eo eo N N ee NN N
15. on lightly the washing machine will start operation after a period of time and the corresponding indicator will go on The range is 0 5 24 hours each touch of this button increases a half hour After the button is set press the Start Pause button to start countdown of the set time the time is displayed on the screen until the program ends E F Key Combination After you press the Start Pause button the EF Key Combination is available Press these two keys simultaneously the sign LOCK and the remaining washing time are displayed on the LED alternately Now all the function keys except the Power switch can be locked Press the key combination again to cancel this function G Detergent distribution drawer Open the drawer three compartments can be seen Compartment 1 Pre wash detergent Compartment 2 Normal Quick wash detergent Compartment 3 Softener conditioning agent perfume etc H Display Such information as remaining wash time temperature and speed setting and error messages will be shown Note After power is switched on the display will go on and the remaining wash time decreases As the water pressure and temperature may differ the remaining time may be adjusted accordingly When the laundry is not balanced during spinning the time may be automatically prolonged These are normal phenomena Page 14 i f Front Load Washing Machine Model HMS1000TVE Program description table Detergent Pieta R
16. ram description table 15 11 Error display and troubleshooting 16 12 Wiring circuit 24 13 Self test program 25 Page Haief Front Load Washing Machine Model HMSTOOOTVE PRODUCT CODE ILLUMINATION AND SERIES INTRODUCTION Model code rule description Model identification HMS 1000 IVE A B C DE Serial code Max spin speed Temprature adjustive Spin speed adjustive Computer control moou gt Examples HMS1000TVE It represents HMS series appearance with big window 180 opening window 1000rpm spin speed Spin speed is adjustive from 400 to 1000 rpm and alse exclude spin indicate 0 temprature is also adjustive you can alse choose cold water It s controlledby computer Page 2 Haier Front Load Washing Machine __ModelHMS100DTVE FEATURES 300mm diameter porthole door may be open at a 180 degrees Facilitate view of wash process facilitate unloading and easy to use with large porthole Multi gear speed controller According to different costuming you can slect corresponding spin speed from 400 to 1000 rpm Unique gasket design featuring no residual water hidden inside By the unique gasket washing machine can left no residual water hidden between outer drum an
17. t valve is it between N ar l PCB AC 220 240 V Page 20 Front Load Washing Machine Model HMS1000TVE HMS1000TVE Examination amp Troubleshooting Failure Display nothing Troubleshooting Repair power supply Measure the power supply is it exists 220V 240V AC voltage Press the power switch Is power switch on Press power switch and check the voltage Make sure power supply cable assembly is between two pins of power switch Is there 220 240V AC voltage connected well and then replace power switch Cut off power and check if plugs are connected Insert the plug well and test well by pulling the plug of PCB Check if power plug exists 220V 240V AC Replace PCB voltage at the import pin Failure no water inletting Troubleshooting Is the tap shut off or the water pressure Open tap or wait for normal water pressure too low Check if water is leaking from washer Reconnect inlet pipe Clean filter Replace electromagnetic valve connection especially between inlet pipe and tap to make sure of no bends Check if filter of electromagnetic valve is jammed Choose pre wash program and start Check if there is 220 240V at import pin of electromagnetic valve IDEE NAL Reconnect the wire Is there open circuit between electromagnetic valve 220 240V Choose pre wash program and start Replace PCB then check if there is 220 240V at export B
18. ter is leaking from the inlet pipe Readjust it or the tap Is drain pipe broken Replace drain pipe Remove clothes Check if there is foreign material nipped between cushion of sight window and sight window Check if all tubes and tie in is leaking ne water including the connecting of tube a Reassemble or repair and valve dispenser tube and dispenser outer cylinder cushion of sight window hose and outer cylinder drain pump and gas valve Replace cushion of sight Is cushion of sight window broken i Den f window Replace outer cylinder Is water leaking from outer cylinder Page 23 i Front Load Washing Machine Model HMS1000TVE Wiring Circuit PCB Printed Circuit Board NTC Temperature Sensor FA Interference Suppresser MR Door Lock Switch Power Switch EVP EVF Water Inlet Magnetic Valve P Pressure Switch PS Drainage Pump Heat Heating element M Motor Page 24 Haief Front Load Washing Mode HMS1000TVE Note 1 11 12 13 If you want to stop the program setting At first you should press the button of start pause only one time Then turn off power If you want to start the program setting again you should turn on the power again so it is ok Switch on the power turn the program botton at drian position press the temperature and start buotton at the same time Machine will start a self test program When the door switch is closed for ten seconds 88 88 will be displaye
Download Pdf Manuals
Related Search