2016 Instructions
Contents
1. QD40305BJ e Slide the drivers A pillar trim upward and remove the driver s A pillar trim 10 Install the new clip Supplied to the driver s A pillar trim e Remove the shop towel and any clips Go to step 12 UPPER i a a CLIP A PILLAR TRIM CLIP supplied DRIVER S A PILLAR TRIM QC72508AJ QD40304BJ 6 of 14 All01797 23 1504 2015 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com Without side curtain airbags 11 Pull away the door opening seal and remove the drivers A pillar trim three clips 3 CLIPS DOOR OPENING SEAL Pull away DRIVER S QD40366BU A PILLAR TRIM 12 Pull away the door opening seal and remove the driver s dashboard side lid six retaining tabs DOOR OPENING SEAL Pull away 6 RETAINING TABS DRIVER S DASHBOAR D SIDE LID PLASTIC TRIM TOOL QD40315AJ 2015 American Honda Motor Co Inc All Rights Reserved All01797 23 1504 13 Attach the tape to the lower column cover sy LoweRCoLumMN TAPE QD40316AJ COVER 14 Pull away the door opening seal and remove the drivers dashboard lower cover 12 clips and unplug the vehicle connectors DOOR OPENING SEAL Pull away VEHICLE CONNECTORS CLIP DRIVER S DASHBOARD 11 CLIPS LOWER COVER QD40317AJ 7 of 14 www collegehillshonda com 15 Pull away the door opening seal and remove the driver s front door sill t2. www collegehillshonda com Remove the driver s sunvisor holder If the vehicle is equipped with the side curtain airbags e Wrap tape around the tip of flat tip screwdriver continue with step 8 If not go to step 11 e Release three retaining tabs on the driver s With side curtain airbags sunvisor holder 8 Remove the drivers A pillar trim 3 RETAINING e Pull away the door opening seal from the driver s FLAT TIP ee A pillar trim SCREWDRIVER Push p e Pull out on the drivers A pillar trim to release three clips DRIVER S A PILLAR Pull the clip SECTION VIEW DRIVER S A PILLAR TRIM DRIVER S SUNVISOR HOLDER QC22003BJ e While holding down the driver s sunvisor holder as shown use a flat tip screwdriver wrapped with a tape to remove the driver s sunvisor holder three retaining tabs 3 RETAINING Xe TABS Push DRIVER S A PILLAR TRIM QD40302BJ Hold down FLAT TIP SCREWDRIVER DRIVER S SUNVISOR HOLDER QC22004AJ 2015 American Honda Motor Co Inc All Rights Reserved All01797 23 1504 5 of 14 www collegehillshonda com e To prevent clips from falling into the body panel 9 Remove the remaining upper clip from the driver s A area carefully insert a shop towel between the pillar drivers A pillar and the drivers A pillar trim UPPER CLIP A PILLAR TRIM DRIVER S A PILLAR Push two tabs DRIVER S A PILLAR SHOP TOWEL QD40303BJ
3. Route the automatic day night mirror harness down the A pillar as shown Align the green tape on the automatic day night mirror harness with the vehicle clip and secure the automatic day night mirror harness to the vehicle harness with two wire ties Do not cover the installation holes of the driver s A pillar trim AUTOMATIC DAY NIGHT MIRROR HARNESS A VEHICLE PANEL AUTOMATI C DAY NIGHT MIRROR VEHICLE HARNESS WIRE TIE SECTION VIEW GREEN TAPE VEHICLE CLIP 2 WIRE TIES VEHICLE HARNESS QD42311AJ 2015 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com 27 Align the green tape on the automatic day night mirror harness with the vehicle clip and secure the automatic day night mirror harness to the vehicle harness with one wire tie VEHICLE HARNESS SECTION VIEW VEHICLE PANEL AUTOMATI C DAY NIGHT MIRROR 4 VEHICLE WIRETIE HARNESS GREEN TAPE VEHICLE CLIP T gt AUTOMATI ih C DAY I NIGHT fe Nea MIRROR WIRE TIE QD42312AJ 28 Using isopropyl alcohol on a shop towel clean the drivers A pillar where the aluminum tape will attach DRIVER S A PILLAR Clean with isopropyl alcohol AUTOMATI C DAY DN NIGHT Rap MIRROR GREENTAPE ALUMINUM QD42313AJ TAPE 29 Attach the green tape on the automatic day night mirror harness to the driver s A pillar with one aluminum
4. passenger s sunvisor holder e Wrap tape around the tip of flat tip screwdriver e Release three retaining tabs on the passenger s sunvisor holder 3 RETAINING FLAT TIP TABS SCREWDRIVER Push PASSENGER S SUNVISOR HOLDER QC22003BJ 3 of 14 www collegehillshonda com e While holding down the passenger s sunvisor 6 holder as shown use a flat tip screwdriver wrapped with a tape to remove the passenger s sunvisor holder three retaining tabs 3 RETAINING TABS Hold down FLAT TIP SCREWDRIVER PASSENGER S SUNVISOR HOLDER QC22004AJ 4 of 14 All01797 23 1504 Remove the driver s sunvisor unplug the vehicle connector e Pivot the driver s sunvisor downward e Wrap tape around the tip of flat tip screwdriver e Locate the slot in the base cover and insert the flat tip screwdriver into the slot Push in and hold the retaining tab e While holding the retaining tab push up on the sunvisor and rotate it toward the door NOTE If the retaining tab does not stay pushed in return the sunvisor to its original position and repeat this step BASE FLAT TIP COVER SCREWDRIVER RETAINING TAB VEHICLE CONNECTOR if equipped Make sure the tab slides into DRIVER S the base cover SUNVISOR Push the retaining tab While pushing in D40301AJ on the tab rotate the sunvisor toward the door 2015 American Honda Motor Co Inc All Rights Reserved
5. tape 2015 American Honda Motor Co Inc All Rights Reserved All01797 23 1504 30 Pull away the door opening seal Route the automatic day night mirror harness down next to the dashboard and tuck the automatic day night mirror harness between the drivers A pillar and the dashboard DOOR OPENING SEAL Pull away DASHBOARD KO RAS I di A AN ah EEEak bi aN NN oo AUTOMATIC DAY NIGHT MIRROR HARNESS DRIVER S A PILLAR QD42314AJ Without Other Accessory Harness 8 pin Connector 31 Plug the automatic day night mirror harness 8 pin connector into the fuse box Go to step 33 FRONT VIEW FUSE BOX Plug in here AUTOMATIC DAY NIGHT MIRROR HARNESS 8 PIN CONNECTOR QD42315AJ 11 of 14 www collegehillshonda com With Other Accessory Harness 8 pin Connector 33 Secure the 8 pin connectors and automatic day 32 night mirror harness to the vehicle harness with If other accessory harness 8 pin connector is wer three wire ties plugged into the fuse box unplug the 8 pin connector from the fuse box then plug the automatic day night mirror harness 8 pin connector into the ONNIE GORS A SWIRE TIES fuse box Remove and discard the dummy connector from the automatic day night mirror harness 8 pin connector and plug other accessory harness 8 pin connector into the automatic day night mirror harness 8 pin connector OTHER AUTOMATIC DAY NIGHT ACCESSORY FUSE Plugin MIRROR HA
6. the CHECK THE OPERATION OF THE AUTOMATIC DAY NIGHT MIRROR 44 Adjust the zone and calibrate as required 2015 American Honda Motor Co Inc All Rights Reserved All01797 23 1504 CHECK THE OPERATION OF THE AUTOMATIC DAY NIGHT MIRROR 1 Turn the engine switch to ON but do not start the engine AUTOMATIC DAY NIGHT MIRROR SWITCH Turn on LED AUTOMATIC DAY NIGHT MIRROR 030406AB 2 Turn on the switch Check that the LED lights 13 of 14 www collegehillshonda com Cover the front sensor on the automatic day night mirror with your hand and use a flashlight to light the rear sensor on the automatic day night mirror Make sure the mirror surface dims AUTOMATIC DAY NIGHT MIRROR MIRROR SURFACE FRONT SENSOR FLASHLIGHT Cover REAR SENSOR 030407AB 4 Step on the brake pedal and move the shift lever to the R position Repeat step 3 and make sure the mirror surface does not dim e Make sure that the parking brake is set securely e If the automatic day night mirror does not function properly check the fuse and all connectors including the ground cable 14 of 14 All01797 23 1504 2015 American Honda Motor Co Inc All Rights Reserved
7. RNESS HARNESS BOX here 8 PIN CONNECTORS 8 PIN CONNECTOR nawe venre coe am gem sssnmm Ni lt SS Wc fa oe ira We rae vai i ha t pir aie i DA i cae gt im allie i AUTOMATIC DAY NIGHT QD42317AJ MIRROR HARNESS 5S Discard OR 34 Route the automatic day night mirror harness along FON gy the vehicle harness Remove the bolt and install the P automatic day night mirror harness ground terminal with one ground bolt QD42316AJ VEHICLE HARNESS BOLT AUTOMATIC DAY QD42318AJ HOOD Discard NIGHT MIRROR OPENER HARNESS GROUND 12 of 14 All01797 23 1504 2015 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com 35 Secure the automatic day night mirror harness to the vehicle harness with two wire ties AUTOMATIC DAY NIGHT MIRROR HARNESS 2 WIRE TIES VEHICLE QD42319AJ HARNESS 36 Check that all wire harnesses are routed properly and all connectors are plugged in 37 Check the overlap between the headliner and the driver s A pillar trim Refer to the Service Manual If necessary adjust the overlap 38 Reinstall all removed parts 39 Reconnect the negative cable to the battery 40 Press and hold the radio power button for two seconds to restore the radio and navi if equipped system functions 41 Reset the clock 42 Restore the systems back to normal operation as described in the Service Manual if necessary 43 Perform
8. allation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do it yourselfers 1 Disconnect the negative cable from the battery 2 Loosen the TORX screw and remove the rearview mirror from the mirror mount TORX SCREW Loosen QD42302BJ REARVIEW MIRROR Discard MIRROR MOUNT 2015 American Honda Motor Co Inc All Rights Reserved 2015 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com Remove the left and right lenses from the map light console four retaining tabs for each lens Remove the two bolts With Moonroof Remove the map light console Then unplug the vehicle connectors and remove the switch four retaining tabs VEHICLE MAP LIGHT CONNECTORS CONSOLE RIGHT MAP LIGHT LENS i o a 2 BOLTS 4 RETAINING TABS SWITCH LEFT MAP 4 RETAINING LIGHT LENS TABS QD42303AJ Without Moonroof Remove the map light console unplug the vehicle connector VEHICLE MAP LIGHT CONNECTOR CONSOLE 4 RETAINING TABS 2 BOLTS RIGHT MAP LIGHT LENS LEFT MAP 4 RETAINING LIGHT LENS TABS QD42304AJ All01797 23 1504 Release the passenger s sunvisor from the passenger s sunvisor holder PASSENGER S PASSENGER S SUNVISOR HOLDER SUNVISOR QD42305AJ Remove the
9. opropyl alcohol FUSE LABEL 2A OPTION AUTOMATIC DAY NIGHT MIRROR HARNESS QD42308AJ 21 Attach the fuse label to the automatic day night mirror harness fuse case 2015 American Honda Motor Co Inc All Rights Reserved All01797 23 1504 22 Using a white marker mark the automatic day night mirror harness at the measurement shown WHITE MARKER AUTOMATIC DAY NIGHT MIRROR HARNESS QDDOS506A4J 9 of 14 23 Plug the automatic day night mirror harness 7 pin connector into the automatic day night mirror MARK Align with the AUTOMATI edge of the headliner C DAY NIGHT VEHICLE MIRROR PANEL AUTOMATIC DAY NIGHT MIRROR HARNESS SECTION SECTION VIEW p AUTOMATI AUTOMATIC C DAY DAY NIGHT NIGHT MIRROR MIRROR HARNESS AUTOMATI op423008u 7 PIN C DAY CONNECTOR NIGHT 24 Gentry pull back the headliner and tuck the automatic day night mirror harness behind the headliner Align the mark on the automatic day night mirror harness with the edge of the headliner Be careful not to crease the headliner 10 of 14 www collegehillshonda com 25 26 All01797 23 1504 Route the automatic day night mirror harness through the groove in the harness cover Secure the harness cover to the mirror stay Slide the harness cover behind the headliner HARNESS COVER AUTOMATIC DAY NIGHT MIRROR AUTOMATI C DAY NIGHT MIRROR AUTOMATIC DAY NIGHT HARNESS QD42310AJ MIRROR COVER
10. rim one clip and six retaining tabs DRIVER S FRONT 3 RETAINING IP DOOR SILL TRIM TABS TABS DOOR OPENING SEAL Pull away QD40319AJ 16 Pull away the door opening seal and remove the drivers kick panel two clips DOOR OPENING SEAL DRIVER S Pull away KICK PANEL QD40320AJ 8 of 14 3 RETAINING 2 CLIPS All01797 23 1504 17 Using isopropyl alcohol on a shop towel clean the vehicle panel where the urethane tape will attach VEHICLE PANEL SECTION VIEW HEADLINER wc FRONT Align the center Ss of urethane tape a J with the center of the mirror mount HALF OF URETHANE TAPE VEHICLE PANEL Clean with Isopropyl alcohol a i MIRROR OV ig MOUNT HALF OF URETHANE TAPE URETHANE TAPE QD42306AJ Cut in half 18 Using scissors cut one urethane tape in half Attach one half of urethane tape to the vehicle panel as shown Be careful not to crease the headliner 2015 American Honda Motor Co Inc All Rights Reserved www collegehillshonda com 19 Install the automatic day night mirror on the mirror mount as shown and tighten the TORX screw TORX SCREW Torque 1 55 2 05 N m 0 16 0 21 kgf m 1 14 1 51 Ibf ft MIRROR MOUNT AUTOMATIC DAY NIGHT QD42307Ad MIRROR 20 Using isopropyl alcohol on a shop towel clean the fuse case where the fuse label will attach FUSE CASE Clean with is
11. www collegehillshonda com HONDA Accessory Application Publications No VERSION 1 N STA L LATI O N AUTOMATIC DAY NIGHT 2016 HR V TEE PARTS LIST Ground bolt Attachment Kit P N 08V03 T7S 100 gt i Automatic day night mirror harness Aluminum tape Harness cover lt gt A Automatic Day Night Mirror Kit EA P N 08V03 TR0 100A Automatic day night mirror 8 Wire ties PS gt ail Accessory User s Information Manual Clip May not used i ia Urethane tape Fuse label 2015 American Honda Motor Co Inc All Rights Reserved All01797 23 1504 08V03 T7S 1000 90 1 of 14 www collegehillshonda com TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat tip screwdriver Ratchet 10 mm Socket Isopropyl alcohol Shop towel Diagonal cutters Torque wrench T20 TORX bit Flashlight Tape 10 mm Open end wrench Scissors White marker Ruler The following tools are available through the Honda Tool and Equipment Program On the iN click on Service gt Service Bay gt Tool and Equipment Program then enter the number under Search Or call 888 424 6857 e Trim Tool Set T N SOJATP2014 e Plastic Trim Tool T N SILTRIMTL10 Illustration of the Automatic Day Night Mirror in the Vehicle AUTOMATIC DAY NIGHT MIRROR AUTOMATI C DAY NIGHT MIRROR 2A FUSE QD42301 AJ 2 of 14 All01797 23 1504 INSTALLATION Customer Information The information in this inst
Download Pdf Manuals
Related Search