Add-A-Leaf - Fat Bob`s Garage
Contents
1. Install front springs assemblies into vehicle using OEM fasteners removed in step 5 If new hardware is needed it is available from BDS 121004 for 1973 87 trucks or 121005 for 1988 91 trucks Leave spring eye bolts hand tight to be tightened with truck on the ground Fully seat spring center pins into axle spring seat and secure springs to axle using the longer u bolts nuts and washers supplied Fig 4 Do not Torque hardware at this time 6 and up lift kits Install sway bar drop kit 121451 per instructions at this time iA Steering Arm Installation if applicable BDS 081401 10 11 12 Clean and oil studs before removing nuts Remove nuts and tapered sleeves Retain for reinstalla tion Remove Arm Clean axle pad and studs inspect for damage or penetrat ing rust Consult the OEM service manual for stud replace ment Install new arm and torque fasteners to 175 ft lbs Fig 5 Page 3 13 14 15 16 Re secure drag link to new steering arm and lock with cot ter pins Install recommended replacement BDS shocks and rein stall front wheels and tires Remove jack stands and lower the front to the ground With the vehicle on the ground go back and torque spring eye bolts to 9 16 130 ft Ibs and 7 16 60 ft lbs Do not over tighten Over tightening the shackle bolts will restrict movement Torque u bolts to 130 150 ft lbs 6 lifts and up Install transfercase lowering ki2. 11 12 13 14 15 16 17 18 19 Raise rear of vehicle and support with jack stands under frame in front of the front spring hanger With axle supported with a floor jack remove the brake line clip attaching the line to frame bracket Pull the line through bracket approximately 4 Caution Careful atten tion must be exercised when re routing brake line Do not kink pinch or stretch brake lines Using hack saw cut a slot through to the hole bend bracket open to remove brake line Bend bracket back into position Secure rear brake line extension Z bracket to frame bracket using 5 16 bolt washers and lock nut Reroute line through extension bracket and secure with clip Remove rear shocks retain all hardware for reinstall Remove rear u bolts and lower axle away from spring as semblies Remove spring to front hanger bolts and shackle bolts Save all hardware for reinstall Remove rear springs Lubricate spring bushings and install into rear lift springs Install rear springs assemblies into vehicle using OEM fasteners removed in step 7 If new hardware is needed it is available from BDS 121009 for 1973 91 trucks Fully seat spring center pins into axle spring seat and secure springs to axle using the longer u bolts nut and washers supplied Do not torque hardware at this time Install recommended replacement BDS shocks and rein stall rear wheels and tires Remove jack stands and lo
3. SHOLE UPPER MHNT i WERT SLIDE SLEEVE TY 1 SAE BUSHING HALVES ONTO GLEEWE G Ser EAE ae T INTO BHOC EVES AMD INSERAT INTO Oo euen s BUSI i _ ih mA Va ah a E O Helgis Qe TI lf y j F PA r j iig re S f W SL TEs iig E yi SLEEVE SLEEVE FRONT SHOCK LOWER MOUNT ASS EMG ED B4GCe8 SHLD LODA LIRE THIS TOARN F a 7 if 7 fil 1 i y i 1 rie A i Li Ti M M WASHERS f T WASHERS r EHOCK MOUNTS Srl MOLUNTH ISTALL 2 710 FLAT WASHERS AT THE AFAA GF THE LOWER WOMUNT OF THE FAONT Se sett iF ARTICA A CV OL ARANGE S HEEDEO KSTALL 1 700 FLFAT WASHER Af EACH SDE OF THE LOWER MQUAT OF THE FRCAT SHOCK CHEV S SERIES W LIFT PART OF VEHICLE INSTALLING BUSHINGS SLEEVE AND BARPINS Some shock absorbers require multiple barpins sleeves and bushings to be included in the kit due to vehicle years and model changes After choosing the correct bushing sleeve and or barpin for your application install it in the shock eye For best results begin by installing the bushing in the shock eye Lubricant will ease this process Next lubricate the inside of the bushing and instalt the steeve or barpin using a bench vise Use care not to scratch or dent the shock body GM Leaf Spring 2 4 6 8 Suspension Systems SUSPENSION P READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE SAFETY WARNING BDS Suspension Co recommend
4. tie strap Install any required bushings and sleeves in to the shock eyes at this time Install the shock ab sorber on the vehicle Use the appropriate illus tration as a frame of reference Due to the differ ent shock mounts within a vehicle model range the shock eyes must be built to match the shocks that you removed by using the universal hard ware kit included Choose the sleeve with an I D closest to the O D of the mounting stud or bolt without binding Some applications will require some extra effort to install Check all fasteners for tightness before driving and inspect periodically SPACER Pressed on Pin rg Part of Vehicle Lockwasher Lockwasher __ Bushing 102 S Michigan Avenue Coldwater MI 49036 517 279 2135 www bds suspension com rev 12 22 2005 L je Nut aE Retaining Washer i Bushings ar Note Caution Qae Retaining Washer When installing bushing on stem type shocks Tighten only enough so that bushing are expanded to the diameter of the outer retaining washer Stud on Shock PART OF VEHICLE 78 x 5 Sleeve 5 8 x 2 1 4 5 8 SAE Washer Sleeve AA ee re anne Long Sleeve r ae ASSEMBLED SHOCK SHOULD LOOK LIKE THIS At a FIG 1 Bie i i REAR f t WASHERS FRONT SHOCK MOUNTS INSTALL 2 7 16 FLAT WASHERS AT THE REAR OF THE LOWER MOUNT OF THE FRONT SHOCK AS IN FIGURE FIG 2 FULL SIZE CHEV W LIFT 88 UP MODELS FRONT
5. Add A Leaf Installation Instructions READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE PRODUCT SAFETY WARNING Certain BDS Suspension products are intended to improve off road performance Modifying your vehicle for off road use may result in the vehicle handling differently than a factory equipped vehicle Extreme care must be used to prevent loss of control or vehicle rollover Failure to drive your modified vehicle safely may result in serious injury or death You should never operate your modified vehicle under the influence of alcohol or drugs Always drive your modified vehicle at reduced speeds to ensure your ability to control your vehicle under all driving conditions Always wear your seat belt Pre Installation Notes 1 Special literature required OE Service Manual for model year of vehicle Refer to manual for proper disassembly reassembly procedures of OE and related components 2 Adhere to recommendations when replacement fasteners retainers and keepers are called out in the OE manual 3 Secure and properly block vehicle prior to installation of BDS Suspension components Always wear safety glasses when using power tools 4 Toproperly perform installation you must use two 2 large C clamps or a large vise to contain the elastic potential energy stored in a leaf spring when the center bolt is removed INSTALLATION INSTRUCTIONS 1 Raise rear of vehi
6. ck and adjustment 4 Re torque all fasteners after 500 miles Always inspect fasteners and components during routine servicing 102 S Michigan Avenue Coldwater MI 49036 517 279 2135 www bds suspension com rev 2 12 2008 Page 1 Front Box Kit Bill of Materials Part Discription 011001 011002 011003 12 1 5 8 x 083 x 3 50 Sleeve 13 1 3 4 x 083 x 3 50 Sleeve BSCVFB GM Front Bushing BSCVRB GM Front Bushing BSCV2 GM Rear Bushing B381G2 3 8 x 1 Bolt LW38 3 8 Lock Washer N38SS 3 8 Nut B56 75G2 5 16 x 3 4 Bolt LW56 5 16 Lock Washer N56SS 5 16 Nut 90BA 90 Degree Brake Bracket SBLA Z Brake Bracket 582340800R 5 8 x 2 3 4 x 8 Round U bolt 583000800R 5 8 x 3 x 8 Round U bolt 983581000R 5 8 x 3 5 8 x 10 Round U bolt N58FH 5 8 Fine High Nuts W58S 5 8 SAE Flat Washer Rear Box Kit Bill of Materials Part Discription 011009 011208 011209 011307 011308 011309 011407 011408 011409 2KB W96 2 Lift Blocks 3KB W96 3 Lift Blocks 4KB W96 4 Lift Blocks 5 8 x 2 9 16 x 12 eee oie Square U bolts 5 8 x 3 x 8 583000800R Round U bolts 5 8 x 3 x 10 SesUO TOUR Round U bolts 5 8 x 3 x 12 SOSDOTZOUR Rourid U bolts 5 8 x 3 5 8 x 10 583581000R Round U bolt 5 8 x 3 5 8 x 12 583581200R Round U bolt W58S 5 8 SAE Washer NS8FH 5 8 Fine High Nuts 3 4 x 083 x 2 950 oa Slee
7. cle and support with jack stands under frame 2 Removetires and wheels 3 Raise the rear axle with a floor jack and support axle with jack stands Remove shocks 4 With axle firmly supported by jack stands remove the axle vent hose from the axle housing Remove the axle u bolts and spring plates 5 Lower axle to allow for spring removal Caution Be careful not to over extend brake lines etc Remove spring eye bolt and shackles bolts Remove springs from the vehicle 6 Using c clamps or large bench vise clamp the spring assembly securely together 7 Ifapplicable remove any leaf spring alignment clips Using vise grips to hold the head of the center bolt loosen and remove tt If the center bolt is rusted a hammer and drift punch may be necessary for removal Carefully remove c clamps or loosen bench vise With a small amount of grease applied to both ends of the add a leaf reassemble leaf pack with new add a leaf in place The leaf pack should be assembled as a pyramid with the longest leaf on top to the shortest leaf on the bottom 10 Use the c clamp to compress the pack back together making sure to align the center pin holes in each leaf Secure with the supplied center pin nut Do not use the center pin to tighten the pack Use the c clamps to compress the pack and then tighten the center pin Cut off any extra pin above the nut Install the supplied leaf alignment clamps 11 Install the springs back in to th
8. de such things as dented cylinders or bent rods caused by obvious side impact rust worn or deformed bushings A shock absorber is a wear item and over time will experience diminished damping resistance due to normal component wear This is not a defect in material or workmanship and is therefore not warrantable BDS Suspension s obligation under all warranties is limited to the repair or replacement at BDS s option of the defective material Any cost of removal installation or reinstallation freight charges incidental or consequential damages are expressly excluded from these warranties INSTALLATION INSTRUCTIONS 1 Note Please read instructions thoroughly before installing shock absorber 2 Remove old shock absorber from vehicle Note any spacers washers sleeves or other hardware and note their location Compare the existing hardware with the supplied hardware Always use new hardware wherever possible Due to the variety of applications you may not use any or all of the hardware supplied You may need to use some of the original hardware If any of the original hardware is damaged corroded bent or broken it must be replaced If installing dust boot do so at this time Note The use of a lubricant like dish soap on the inside of the boot will ease installation Make sure the washer at the top of the shock is fully seated in the boot all the way around Secure the bottom of the boot to the cylinder with a plastic
9. e vehicle Reinstall the spring eye bolts and or shackles according to OE instructions but do not tighten at this time Use the hydraulic jack to raise or lower the axle to the springs depending on the vehicle making sure to align the center pin head in the axle seat Install the new u bolts and OE spring plates according to OE instructions and torque u bolt nuts to factory specs 12 Reconnect the axle vent hose and install replacement BDS shock absorbers Note Original shocks will probably be too short 13 Lower vehicle to the ground Bounce on the vehicle several times to allow the shackles to swing out to the proper position then tighten the spring frame mounting bolts and the shackle bolts to OE specification Inspect for proper clearance Test drive You must tighten the u bolts again after 100 miles Check all fasteners after 500 miles 102 S Michigan Avenue Coldwater MI 49036 517 279 2135 www bds suspension com Shock Absorber Installation Instructions A READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO INSTALLATION OF SYSTEM AND OPERATION OF VEHICLE LIMITED LIFETIME WARRANTY BDS Suspension Co warrants to the original retail purchaser that its shock and stabilizer cylinders are free from defects in material and workmanship for so long as they own the vehicle Excluded from this warranty are the finish of the product and mounting bushings Defects in material and workmanship do not inclu
10. nd related components 4 Post suspension system vehicles may experience drive line vibrations Angles may require tuning slider on shaft may require replacement shafts may need to be lengthened or trued and U joints may need to be replaced 5 Secure and properly block vehicle prior to installation of BDS Suspension components Always wear safety glasses when using power tools 6 If installation is to be performed without a hoist BDS Suspension Co recommends rear alterations first 7 Due to payload options and initial ride height variances the amount of lift is a base figure Final ride height dimensions may vary in accordance to original vehicle attitude Always measure the attitude prior to beginning installation POST INSTALLATION WARNINGS 1 Check all fasteners for proper torque Check to ensure for adequate clearance between all rotating mobile fixed and heated members Verify clearance between exhaust and brake lines fuel lines fuel tank floor boards and wiring harness Check steering gear for clearance Test and inspect brake system 2 Perform steering sweep to ensure front brake hoses have adequate slack and do not contact any rotating mobile or heated members Inspect rear brake hoses at full extension for adequate slack Failure to perform hose check replacement may result in component failure Longer replacement hoses if needed can be purchased from a local parts supplier 3 Perform head light che
11. s this system be installed by a professional technician In addition to these instructions professional knowledge of disassembly reassembly procedures and post installation checks must be known PRODUCT SAFETY WARNING Certain BDS Suspension products are intended to improve off road performance Modifying your vehicle for off road use may result in the vehicle handling differently than a factory equipped vehicle Extreme care must be used to prevent loss of control or vehicle rollover Failure to drive your modified vehicle safely may result in serious injury or death BDS Suspension Co does not recommend the combined use of suspension lifts body lifts or other lifting devices You should never operate your modified vehicle under the influence of alcohol or drugs Always drive your modified vehicle at reduced speeds to ensure your ability to control your vehicle under all driving conditions Always wear your seat belt PRE INSTALLATION NOTES 1 Special literature required OE Service Manual for model year of vehicle Refer to manual for proper disassembly reassembly procedures of OE and related components 2 Adhere to recommendations when replacement fasteners retainers and keepers are called out in the OE manual 3 Larger rim and tire combinations may increase leverage on suspension steering and related components When selecting combinations larger than OE consider the additional stress you could be inducing on the OE a
12. t 121000 per there instructions at this time Rear Block Kits Note Steps 2 4 apply to 4 amp 6 lifts only 1 10 11 12 13 14 Raise rear of vehicle and support with jack stands under frame in front of the front spring hanger With axle supported with a floor jack remove the brake line clip attaching the line to frame bracket Pull the line through bracket approximately 4 Caution Careful atten tion must be exercised when re routing brake line Do not kink pinch or stretch brake lines Using hack saw cut a slot through to the hole bend bracket open to remove brake line Bend bracket back into position Secure rear brake line extension Z bracket to frame bracket using 5 16 bolt washers and lock nut Reroute line through extension bracket and secure with clip Remove rear shocks retain all hardware for reinstall Remove rear u bolts and lower axle away from spring as semblies If installing an add a leaf 119157 or 119158 do so now per their instructions Place lift blocks on top of axle spring seat tapered end forward and secure with supplied u bolts Torque u bolts to 130 150 ft lbs Fig 6 Install recommended BDS shocks with reused hardware Reinstall wheels and tires Double check all hardware torque Adjust headlights Check all moving parts for clearance A front end alignment should be performed Recheck all fasteners after 500 miles Page 4 Rear Spring Kits 1 10
13. ve 3624RB Spring Eye Bushings Page 2 Installation Instructions Front 1 Raise vehicle and place jack stands under frame ap proximately 3 behind front spring shackles Remove front wheels and shocks Remove one rivet from the outside of the frame at the en gine crossmember closest to the OE hose to steel line con nection Attach the 90 degree brake line extension brackets using the 3 8 x 1 bolts nuts and lock washers Disconnect front brake line at frame and reroute through extension brackets and secure CAUTION Careful atten tion must be exercised in rerouting Do not kink pinch or stretch lines When both sides have been completed bleed the brakes Refill the master cylinder with Dot ap proved fluid Place hydraulic floor jack under front differential and rise to support differential Remove cotter pin and nut securing the drag link to stock steering arm Use pickle fork to de seat tapered stud from arm Fig 1 Remove front spring to axle u bolts Fig 2 Remove spring to front hanger bolts and shackle bolts Fig 3 Save all hardware for reinstall Remove front springs 6 and up lift kits remove sway bar to frame bushing bolts save all hardware for reinstall Support sway bar with strap to frame or with jack stand Lubricate spring bushings and install into front lift springs Large bushing and steel sleeve into front eyes Small bushing and 7 steel sleeve into rear eyes
14. wer the rear to the ground Torque u bolts to 130 150 ft lbs torque spring eye bolts to 9 16 130 ft lbs and 7 16 60 ft lbs Do not over tighten Over tightening the shackle bolts will restrict movement Double check all hardware torque Adjust headlights Check all moving parts for clearance A front end alignment should be preformed Recheck all fasteners after 500 miles
Download Pdf Manuals
Related Search