A9900403 - Arrows sliencer.fm
Contents
1. as described in the service manual 44 Reconnect the battery positive red lead first EFI models only Note e The correct engine calibration must be downloaded to the motorcycle ECU prior to starting the engine This information can be found on the Triumphonline net dealer web site 45 Connect the Triumph Diagnostic Tool and download the correct engine calibration to the ECU following the procedure listed on the Triumphonline net dealer web site All models 46 Refit the seat as described in the service manual 47 Switch on the ignition and check that the horn operates correctly 48 Remove the paddock stand 7 of 8 49 Check the engine oil level Top up if necessary as described in the appropriate service manual 50 Start the engine and check for oil leaks 51 Stop the engine and adjust the engine oil level as described in the appropriate service manual After this Arrow exhaust accessory kit has been fitted by an authorised Triumph dealer the performance of the motorcycle will be altered if you have any doubt about the performance of any aspect of the motorcycle contact an authorised Triumph dealer and do not ride the motorcycle until the authorised dealer has declared it fit for use Riding a motorcycle when there is any doubt as to any aspect of the performance of the motorcycle may result in loss of control of the motorcycle leading to an accident After fitting the accessory2. kit the motorcycle will exhibit new handling characteristics Operate the motorcycle in a safe area free from traffic to gain familiarity with any new characteristics Operation of the motorcycle when not familiar with any new handling characteristics may result in loss of motorcycle control and an accident The motorcycle must not be operated above the legal road speed limit except in closed course conditions Only operate this Triumph motorcycle at high speed in closed course on road competition or on closed course racetracks High speed operation should only be attempted by riders who have been instructed in the techniques necessary for high speed riding and are familiar with the motorcycle s characteristics in all conditions High speed operation in any other circumstances is dangerous and will lead to loss of motorcycle control and an accident 8 of 8
3. sidestand is held in exactly the same position as the original condition When correctly positioned tighten the sidestand bracket fixings to 45 Nm 5 Remove the fuel tank and seat as described in the appropriate service manual 6 Disconnect the battery negative black lead first Remove the original exhaust system as described in the service manual Retain the footrests and all exhaust fixings for reuse Retain the original exhaust system if the motorcycle is to be returned to its original condition Remove and discard the exhaust gaskets from the cylinder head EFI models only Unscrew the oxygen sensors from the original exhaust header pipes 10 The oxygen sensors will remain attached to the motorcycle by the sensor cables which are secured to the motorcycle frame with cable clips Note The oxygen sensor electrical connections must not be swapped between cylinders If the connections are swapped over engine malfunctions will occur The right hand cylinder 2 oxygen sensor connector on the main harness is marked with red tape The oxygen sensors are NOT marked always ensure the right hand oxygen sensor harness is connected to the main harness connector identified with red tape 11 Remove the horn mounting bracket fixing and move the horn and bracket to one side Retain the fixing for reuse N n 2 AH MON 1 Horn 2 Mounting bracket 3 Fixing 12 Support the horn to ensure it does no
4. IUMP English Fitting Instructions Bonneville Bonneville T100 and Thruxton A9600467 and A9600053 Thank you for choosing this Triumph genuine accessory kit This accessory kit is the product of Triumph s use of proven engineering exhaustive testing and continuous striving for superior reliability safety and performance Completely read all of these instructions before commencing the installation of the accessory kit in order to become thoroughly familiar with the kit s features and the installation process These instructions should be considered a permanent part of your accessory kit and should remain with it even if your accessory equipped motorcycle is subsequently sold Parts Supplied 1 Left hand header pipe 1 off 9 Sidestand stop long 1 off 2 Right hand header pipe 1 off 10 Screw M10 x 30 1 off 3 Intermediate pipe 1 off 11 Nut M10 1 off 4 Silencer 1 off 12 Cable tie 2 off 5 Spring 2 off 13 Sealing washer M18 2 off 6 Gasket 2 off 14 Spacer plate 2 off 7 Stand stop bracket 1 off 15 Main jet 112 2 off 8 Sidestand stop short 1 off 16 Exhaust blanking plug 2 off Publication part number A9900403 issue 5 ADC 12197 1of 8 Triumph Designs Ltd 2012 This Arrow exhaust accessory kit is for racing only It is for use solely during closed course racing This Arrow exhaust kit must not be used on public roads It is illegal to use this exhaust accessory kit on t
5. acket Secure with the original fixing Tighten the fixing to 18 Nm NS NO Z i 1 ee N h eA D N 4 QBS 3 AA wA L N LORT o S Z A AKIA Ik 1 Horn 2 Mounting bracket 3 Fixing 6of8 All models 35 Tighten the left hand and right hand header pipe flange fixings progressively and evenly to 19 Nm 1 Header pipe flange right hand shown 1 Fixings 36 Tighten the silencer front fixings to 22 Nm 37 Tighten the right hand rear footrest fixings to 27 Nm 38 Reposition the oil cooler pipe centrally between the right hand header pipe and frame 39 Position a new sealing washer on each side of the oil cooler pipe and secure the pipe to the oil cooler with the original banjo bolt 1 Oil cooler pipe 2 Banjo bolt 3 Oil cooler union 4 Sealing washer Use an open ended spanner to counter hold the oil cooler union as the banjo bolt is tightened 40 Tighten the banjo bolt to 45 Nm 41 Fit the two springs from the kit to secure the intermediate pipe to the header pipes A length of unused electrical cable or string may assist fitment of the springs as shown below 1 Intermediate pipe 2 Header pipes 3 Springs Bonneville and Bonneville T100 Only 42 Refit the outrigger and sprocket cover removed during original exhaust removal on the right hand side of the motorcycle as described in the service manual All models 43 Refit the fuel tank
6. e wrench of known accurate calibration must be used when fitting this accessory kit Failure to tighten any of the fasteners to the correct torque specification may result in loss of motorcycle control and an accident Note Centre stand accessory kits must not be fitted when this Arrow exhaust system is fitted to the motorcycle If the motorcycle has a centre stand accessory kit fitted it must be removed before fitting this Arrow exhaust system If this accessory kit is fitted to Bonneville models with a 790cc carburettor engine the standard main jets must be replaced with the new 112 main jets provided in the kit as described in the appropriate Triumph Service Manual No modification is required if the kit is fitted to Bonneville models with an 865cc carburettor engine If the engine has recently been running the exhaust system will be hot Before working on or near the exhaust system allow sufficient time for the system to cool as touching any part of a hot exhaust could cause burn injuries Note e Before fitting this accessory kit ensure the owner of the motorcycle has been informed of the Warnings contained in these instructions Ensure that the appropriate Triumph Service Manual is available for reference during the fitting of this accessory kit 1 Do not remove the original exhaust system at this stage 2 Bonneville and Bonneville T100 Fit the short sidestand stop into the stand stop brack
7. et Ensure the sidestand stop locates securely in the stand stop bracket Thruxton Fit the long sidestand stop into the stand stop bracket Ensure the sidestand stop locates securely in the stand stop bracket 1 Stand stop bracket 2 Sidestand stop short shown 2 of 8 3 Fit the new side stand stop bracket to the underside of the frame as shown below Retain with the M10 x 30 screw and nut provided Do not fully tighten the fixings at this stage 1 Stand stop bracket 2 Sidestand 3 Screw M10 x 30 4 Nut M10 It is essential that the sidestand is held in the same position as that achieved by the original sidestand stop If the sidestand is positioned incorrectly it will reduce the maximum bank angle Reducing the maximum bank angle will allow the sidestand to contact the road surface during riding leading to loss of motorcycle control and an accident Note e If necessary fit the spacer plates provided between the motorcycle frame and sidestand bracket to ensure the sidestand stop contacts the sidestand when the sidestand is held in exactly the same position as the original condition e Thruxton only If necessary replace the long sidestand stop with the short sidestand stop to ensure the sidestand stop contacts the sidestand when the sidestand is held in exactly the same position as the original condition 4 Adjust the sidestand bracket to ensure the sidestand stop contacts the sidestand when the
8. he public roads This exhaust accessory kit does not comply with local laws and regulations If you use this exhaust accessory kit on public roads you may be prosecuted This accessory kit is designed for use on Triumph Bonneville Bonneville T100 and Thruxton motorcycles only and should not be fitted to any other Triumph model or to any other manufacturer s motorcycle Fitting this accessory kit to any other Triumph model or to any other manufacturers motorcycle will affect the performance stability and handling of the motorcycle This may affect the riders ability to control the motorcycle and could cause an accident Always have Triumph approved parts accessories and conversions fitted by a trained technician of an authorised Triumph dealer The fitment of parts accessories and conversions by a technician who is not of an authorised Triumph dealer may affect the handling stability or other aspects of the motorcycles operation which may result in loss of motorcycle control and an accident This racing exhaust system is covered by a twelve month manufacturers warranty Triumph warranty standard terms and conditions are not affected by the fitment of the Bonneville Bonneville T100 and Thruxton Arrow exhaust system Throughout this operation ensure that the motorcycle is stabilised and adequately supported on a paddock stand to prevent risk of injury from the motorcycle falling A torqu
9. int on the motorcycle frame Refit the right hand rear footrest and secure with the original fixings Do not fully tighten the fixings at this stage 1 Silencer 2 Silencer rear fixing bracket 3 Footrest right hand 4 Motorcycle frame 5 Fixings 30 Refit the left hand footrest Tighten the fixings to 27 Nm 5 of 8 EFI models only 31 Recover the original oxygen sensors and screw into the ports provided in the header pipes Ensure the left hand and right hand oxygen sensor configuration is correct as shown below Tighten the oxygen sensors to 25 Nm 1 Header pipe right hand 2 Oxygen sensor right hand 3 Header pipe left hand 4 Oxygen sensor left hand Note e The oxygen sensor electrical connections must not be swapped between cylinders If the connections are swapped over engine malfunctions will occur The right hand cylinder 2 oxygen sensor connector on the main harness is marked with red tape e The oxygen sensors are NOT marked always ensure the right hand oxygen sensor harness is connected to the main harness connector identified with red tape 32 Pull the oxygen sensor connectors through the frame past the top oil cooler fixing point as shown below I vy 2 K lt A iA a QO 1 Oxygen sensor connectors 2 Top oil cooler fixing JJ ZZ 33 Connect the oxygen sensors to the motorcycle wiring harness 34 A Refit the horn and mounting br
10. n ended spanner to counter hold the oil condition 7 cooler union as the banjo bolt is slackened 16 Pull the left hand oxygen sensor cable through the frame past the oil cooler 23 Slacken and remove the banjo bolt from the lower 17 Refit the oil cooler fixings and tighten to 9 Nm oil cooler pipe Retain the banjo bolt for reuse 18 Re route the left hand oxygen sensor cable around ac the sealing washers from each side of the oil cooler pipe the motorcycle frame to follow the routing of the right hand oxygen sensor cable 4of8 Carburettor models only 24 Tighten the oxygen sensor boss blanking plugs located on the new left hand and right hand header pipes to 25 Nm EFI models only 25 Remove the oxygen sensor blanking plugs located on the new left hand and right hand header pipes and discard All models 26 Fit the new exhaust gaskets provided into the cylinder head 1 Exhaust gasket 27 Fit the new left hand exhaust header pipe first then the new right hand header pipe Retain both header pipes with the original fixings Do not fully tighten the fixings at this stage SJ A 1 Header pipe right hand 2 Header pipe left hand 28 Fit the new intermediate pipe onto the new header pipes 1 Intermediate pipe 2 Header pipes 29 Fit the new silencer assembly onto the intermediate pipe Align the silencer rear fixing bracket with the original right hand mounting po
11. t hang from the wiring 3 of 8 13 Remove the top oil cooler fixing Remove the cable guide Retain the cable guide if the motorcycle is to be returned to its original condition Retain the fixing for reuse When securing electrical cables with cable ties ensure the cable ties are fully tight Ensure there is slack in the cables 19 Retain the left hand oxygen sensor cable to the motorcycle frame with cable ties close to the right hand oxygen sensor cable retaining clips 20 Cable tie the oxygen sensor cables to the frame lug as shown below Ensure there is a minimum of 10 mm clearance from the oxygen sensor cables to the engine sump ae 1 Oil cooler 2 Cable guide 3 Fixing 14 Remove the bottom oil cooler fixings to allow clearance for the left hand oxygen sensor cable to be re routed Retain the fixings for reuse 21 Trim off the excess cable tie material from all cable ties All models Note e The lower oil cooler pipe must be disconnected from the oil cooler The oil cooler pipe will need to be _ re positioned after the new exhaust system has been fitted to ensure correct clearance from the right hand header pipe 1 Oil cooler 22 Position a suitable clean container beneath the oil 2 Fixings cooler to catch any oil 15 Remove the cable clips retaining the left hand oxygen sensor cable to the frame Retain the clips if the motorcycle is to be returned to its original Use an ope
Download Pdf Manuals
Related Search