ReadyLift® (Part# 69-2517CP & 69-2518CP) Installation Instructions
Contents
1. BEANE 5 8 ReadyLift Part 69 251 7CP amp 69 2518CP Installation Instructions 2005 UP Ford F 250 Super Duty 4WD w Camper Package SAFETY WARNING ReadyLift Suspension Inc recommends this system be installed by a professional techni cian In addition to these instructions professional knowledge of disassembly reassembly procedures and post installation checks must be known PRODUCT SAFETY WARNING Modifying your vehicle ride height may result in the vehicle handling differ ently than a factory equipped vehicle Extreme care must be used to prevent loss of control or vehicle rollover Failure to drive your modified vehicle safely may result in serious injury or death ReadyLift Suspension Inc does not recommend the combined use of suspension lifts body lifts or other lifting devices You should never operate your modified vehicle under the influence of alcohol or drugs Always drive your modified vehicle at reduced speeds to ensure your ability to control your vehicle under all driving conditions Always wear your seat belt Pre Installation Notes 1 Special literature required OE Service Manual for model year of vehicle Refer to manual for proper disas sembly reassembly procedures of OE and related components 2 Adhere to recommendations when replacement fasteners retainers and keepers are called out in the OE manual 3 Larger rim and tire combinations may increase leverage on suspension steering and related components When2. Installation Instructions 2005 UP Ford F 250 Super Duty 4WD w Camper Package Please read instructions thoroughly and completely before beginning installation Installation by a trained mechanic is highly recommended Remove the two 19mm bolts on the factory Track Bar track bar bracket one on each side of the track bar mount Remove the three 21mm nuts located on the cross member Remove track bar bracket Install ReadyLift track bar bracket using the factory hardware Torque to factory specs Reference torque specs on front page Using factory hardware re install track bar onto the new ReadyLift track bar bracket Re install sway bar end links Torque to factory specs Reference torque specs on front page Remove OEM front bump stops Remove the 10mm bolts that attach the bump stop brackets to the frame Install ReadyLift bump stop extension bracket Using a Phillips screw driver in sert it into the holes in the extension and use the handle as a leverage point to tighten Install OEM bump stop bracket using nut provided Install OEM bump stop Me aa 2005 2007 Models Reinstall brake line A Passida support brackets i a 2008 models drill 3 8 hole approximately Y 2 below the factory hole use the factory self tapping screw to re attach the brake line support bracket OEM Hott ReadyLift 2060 Placentia Ave Suite B 1 Costa Me
3. ace and your vehicle you are using jack DRIVE SAFELY and stands or a lift rated WEAR YOUR SEAT for the weight of the BELT vehicle Tire and Wheel Fitment For 35 tires 835x12 50 Mounted on a wheel no wider than 9 5 with O offset or 5 25 backspacing For 37 tires 37x12 5 Mounted on the factory wheel or on a wheel no wider than 8 with a 35 offset or 6 backspacing Please note that with this fitment the tire will rub a little at full turn on the radius arm You will also need to pull the inner fender liner back with both of these fitments The best way to accomplish this is to install the ReadyLift inner fender liner support kit Drill an 1 8 hole on the inner lip of the fender liner and an 1 8 hole on the underside of the body Using the self tapping screw and speed clip provided attach the bracket to the fender liner then attach the other end to the body See photos below Alignment Specs Toe Left 1 32 Toe Right 1 32 ReadyLift 2060 Placentia Ave Suite B 1 Costa Mesa CA 92627 Toll Free 800 549 4620 Local 949 515 0795 Fax 949 515 0655
4. eplacement hoses if needed can be pur chased from a local parts supplier 3 Headlight adjustment is highly recommended 4 Re torque all fasteners after 500 miles Always inspect fasteners and components during routine servicing ReadyLift 2060 Placentia Ave Suite B 1 Costa Mesa CA 92627 Toll Free 800 549 4620 Local 949 515 0795 Fax 949 515 0655 RIENDA ae LEVELING SUSPENSION ReadyLift Part 69 251 7CP amp 69 2518CP Installation Instructions 2005 UP Ford F 250 Super Duty 4WD w Camper Package Bill of Materials 9 Description Metal coil spacer Polyurethane sound insulator Shock extension bracket M14 x 90mm bolt M14 Washer M14 Nylon lock nut 16mm carrier bearing spacer 7 16 x 2 1 4 bolt not pictured Bump stop extension bracket M8 x1 25 Nylon lock nut 05 07 F350 Pan hard bracket 69 2517 only 08 09 F350 Pan hard bracket 69 2518 only Inner Fender Liner brackets w hardware ReadyLift Aluminum 6 Decal ReadyLift OEM Style 4 block Driver side ReadyLift OEM Style 4 block Passenger side U bolts with hardware A NNa HH NYNNH YNANND PO ReadyLift 2060 Placentia Ave Suite B 1 Costa Mesa CA 92627 Toll Free 800 549 4620 Local 949 515 0795 Fax 949 515 0655 RIENDA A T ReadyLift Part 69 2517CP amp 69 2518CP Installation Instructions 2005 UP Ford F 250 Super Duty 4WD w Camper Package Please read instructions thoroughly and completely before beginning ins
5. sa CA 92627 Toll Free 800 549 4620 Local 949 515 0795 Fax 949 515 0655 BEANE 8 ReadyLift Part 69 251 7CP amp 69 2518CP Installation Instructions 2005 UP Ford F 250 Super Duty 4WD w Camper Package Please read instructions thoroughly and completely before beginning installation Installation by a trained mechanic is highly recommended Carrier Bearing Spacer Installation Remove the two 15mm bolts use a jack stand to support the drive shaft Install the ReadyLift carrier bearing spacer using the hardware provided Torque to factory spec Reference torque specs on front page Rear Block Installation Remove the four 24mm nuts on one side Remove the U bolts Using a jack carefully raise the truck by the leaf spring until OEM block is loose and there is enough room the for new block Install ReadyLift 4 rear block Please note that the arrow on the bot tom of the block points to the front of the truck Install ReadyLift U bolts using the hardware provided Torque to factory specs Repeat on opposite side Pp Be sure to double check that all hardware has been tightened and torqued to factory specs Remount wheels and
6. selecting combinations larger than OE consider the additional stress you could be inducing on the OE and related components 4 Post suspension system vehicles may experience drive line vibrations Angles may require tuning slider on shaft may require replacement shafts may need to be lengthened or trued and U joints may need to be re placed 5 Secure and properly block vehicle prior to installation of ReadyLift Suspension Inc components Always wear Safety glasses when using power tools 6 If installation is to be performed without a hoist ReadyLift aSuspension Inc recommends rear alterations first 7 Due to payload options and initial ride height variances the amount of lift is a base figure Final ride height dimensions may vary in accordance to original vehicle attitude Always measure the attitude prior to beginning installation POST INSTALATION WARNINGS 1 Check all fasteners for proper torque Check to ensure for adequate clearance between all rotating mobile fixed and heated members Verify clearance between exhaust and brake lines fuel lines fuel tank floor boards and wiring harness Check steering gear for clearance Test and inspect brake system 2 Perform steering sweep to ensure front brake hoses have adequate slack and do not contact any rotating mobile or heated members Inspect rear brake hoses at full extension for adequate slack Failure to perform hose check replacement may result in component failure Longer r
7. tallation Installation by a trained mechanic is highly recommended Position truck on a flat surface and lift vehicle by the frame until the front wheels are off the ground Use a floor jack and support the frame with jack stands or a 2 two post lift if available Two jacks may be needed to lift and lower the front differential during installation Remove front wheels Remove the lower shock bolt Use a floor jack to raise the dif ferential to release any pressure on the lower shock bolt making the removal easier With the jack still supporting the axle unbolt the 13mm brake line support bracket from the frame on both sides 2005 2007 2008 Remove upper track bar 30mm nut and r Noe hol ls bolt Remove sway bar end link bolt on both sides 19mm 21mm Lower differential and remove spring Install Readylift coil spacer Order of assembly Coil A factory isola tor B coil spacer C polyurethane sound insulator D Reinstall coil and raise differ ential Install shock extension onto shock using the hardware provided Install shock extension bracket into factory shock mounting location on the axle using the factory hardware Torque to factory specs Reference torque specs on front Dage ReadyLift 2060 Placentia Ave Suite B 1 Costa Mesa CA 92627 Toll Free 800 549 4620 Local 949 515 0795 Fax 949 515 0655 RIEAN LiF T ReadyLift Part 69 251 7CP amp 69 2518CP
8. tires and torque to factory specs Re torque wheels after 25 miles See next page for Tire wheel fitment specifications Wheel Alignment a Certified Alignment Technician that is experienced with lifted vehicles is recommended to perform the alignment It is recommended that you have your vehicle s alignment checked whenever installing new tires It is also recommended that you adjust your headlights whenever your vehicle s ride height is altered This ReadyLift Leveling Kit is designed and engineered to level out a stock vehicle with no prior modifications The use of this kit along with items such as suspension lifts body lifts or any other type of lifting accessory shall be done at the vehicles owners risk and will void any and all warranties in effect or implied by ReadyLift This kit is not for off road abuse ReadyLift 2060 Placentia Ave Suite B 1 Costa Mesa CA 92627 Toll Free 800 549 4620 Local 949 515 0795 Fax 949 515 0655 RIEANDM ae LEVELING SUSPENSION ReadyLift Part 69 2517CP amp 69 2518CP Installation Instructions 2005 UP Ford F 250 Super Duty 4WD w Camper Package Vehicle Handling Installation Warning Warning Always wear proper Vehicles with larger safety equipment and wheels and tires will use the correct tools handle differently than when installing any stock vehicles Take suspension upgrade time to familiarize your Make sure vehicle is self with the handling of on a flat surf
Download Pdf Manuals
Related Search