4" lift spindles 05-13 tacoma 2wd, 06-13 fj cruiser 2wd 03
Contents
1. some ATAKEA rotors D 15 Remove the ABS line from the clip on the upper control arm then remove the ABS line from the 16 Remove bracket from upper control arm and discard then remove ABS bracket from brake line bracket and discard 17 Bend the tab on the brake line bracket then attach brake line bracket to the new spindle using the supplied hardware r se a Pi i 18 Remove stock brake line at the frame amp caliper then install new one We suggest installing on frame side first to let fluid bleed through the new line then attach on caliper side Cay p 19 Tighten the new brake lines per reversing the above steps 20 Add more bend to the brake line retainer clip to create more tension on the new brake line Hak i w n 21 Remove the ABS line from behind the shock tower Use supplied adell clamp to guide line across the Upper Control Arm do the same with the clamps on the spindle using supplied bolts x4 a i m Wh E 22 Tighten ABS sensor below the lower ball joint Reinstall cotter pin to the upper ball joint and tie rod See below for suggested brake line and ABS routing 23 Manipulate the extra tab on the brake line bracket either by bending it out of the way to prevent contact on the sway bar at full turn or cutting it off2. MAXTRAC SUSPENSION 4522 E EISENHOWER CIR ANAHEIM CA 92807 877 929 3016 WWW MAXTRACSUSPENSION COM SALES MAXTRACSUSPENSION COM PRODUCT 706840 4 LIFT SPINDLES 05 13 TACOMA 2WD 06 13 FJ CRUISER 2WD 03 08 4 RUNNER 2WD PARTS LIST QTY PLEASE DOUBLE CHECK THE PARTS LIST BEFORE BEGINNING INSTALLATION TO 5 8 11 X 3 1 4 HEXBOLT GRD8 4 ENSURE ALL PARTS ARE PRESENT IF 5 8 11 STOVER LOCKNUT GRD8 4 THERE IS SOMETHING MISSING PLEASE 5 8 FLAT WASHER SAE GRD8 8 CONTACT MAXTRAC IMMEDIATELY 1 4 ADEL LOOP CLAMP O4 877 929 3016 1 4 20 X 1 1 4 HEX BOLT GRD 5 ZINC 6 READ THE INSTRUCTIONS THOROUGHLY 1 4 20 NYLON LOCKNUT ZINC 6 ANDCOMPLETELY BEFORE BEGINNING THE INSTALLATION PRIOR TO INSTALLATION 1 2 3 4 J Factory service manual is recommended to have on hand Secure and properly block vehicle prior to beginning installation Always wear safety glasses when using power tools or working under the vehicle Modifications to any part will void the warranty associated with that product Jack up front of vehicle place jack stands under frame behind front suspension After removing parts from vehicle save hardware for reinstallation IT IS RECOMMENDED THAT YOU HAVE YOUR VEHICLE S ALIGNMENT CHECKED WHEN INSTALLING NEW SUSPENSION IT IS ALSO RECOMMENDED THAT YOU ADJUST YOUR HEADLIGHTS WHENEVER YOUR VEHICLE S RIDE HEIGHT IS ALTERED i 2 3 On level ground using a floor jack raise th
3. e front end of your Tacoma and place jack stands under frame behind the front suspension Remove the brake line bracket that is attached to the spindle and move out of the way Remove brake caliper then support it do not allow it to hang from the brake hose 4 Remove brake rotor si Remove the sway bar end link from the spindle 6 Remove the unit bearing then discard backing plate dust shield 7 Remove the cotter pins from the tie rod and upper ball joint 8 Remove the nut from the tie rod end and then break the tie rod loose by hitting the side of the cause damage 10 Remove bolts from lower ball joint steering stop plate then break upper ball joint loose by hitting the side of the spindle do not hit the thread remove stock spindle 11 Guide ABS line down between the new spindle and lower ball joint steering stop plate Slide lower ball joint into the double sheer mount amp attach upper ball joint to new spindle tightening nut on n ball joint align cotter pin hole amp install OEM cotter pin 13 Rotate outer tie rods 180 degrees this will now allow you to install the tie rod ends from the top of the steering arm 14 Reinstall Unit Bearing without the backing plate dust shield then install the rotor and caliper per earlier instructions Make sure that your rotor has enough clearance on the back side near the spindle we ve manufactured the spindle to allow tor all OEM and
Download Pdf Manuals
Related Search