screamin` eagle performance air cleaner kit - Harley
Contents
1. Item Description Quantity Part Number 1 O ring 2 113 2 11292 2 Backplate chrome Kit 29400128 29000020A Backplate black Kit 29400127 29000007A 3 Gasket throttle body 29059 88A 4 Screw socket head cap 1 4 20 x 2 0 in 51 mm long 3 Not sold separately 5 Plug breather 2 29557 05 6 Bracket mounting 29400119 7 Air filter element 29400118 8 Screw hex socket flat head 5 16 18 x 2 0 in 51 mm long Not sold separately 9 Cover air cleaner Not sold separately 10 Medallion Screamin Eagle 14100367 11 Screen air filter chrome Kit 29400128 29400082 Screen air filter black Kit 29400127 29400100 12 O ring medallion 11170 13 Pre charger 29400121 Items mentioned in text but not included in kit A Breather screw 2 J05679 3of32. cylinder head 4 Insert the breather screws through the backplate 5 Thread screws into the cylinder head but do not tighten 6 Thread air cleaner mounting screws 4 through the mounting bracket 6 and into the backplate 2 until the screw threads are captured in induction module Do not fully tighten at this time 7 Alternately tighten two breather screws 5 to 120 144 in Ibs 13 6 16 3 Nm 8 Tighten three air cleaner screws 4 to 55 60 in Ibs 6 2 6 8 Nm 9 Press breather plugs 5 into breather screw cavities aligning tubes with recesses in backplate 1 of 3 Please dispose of materials responsibly Install Air Cleaner Element and Cover NOTE Whenever the air cleaner cover is installed apply Loctite 243 blue to the air cleaner cover screw 8 1 See Figure 1 Install the air cleaner element 7 and cover 9 Before tightening the center screw align the cover using the medallion for best appearance then tighten center screw to 36 60 in lbs 4 1 6 8 Nm NOTE Apply a small amount of dish soap to medallion O ring to aid in installation of medallion 2 Install the medallion into the center hole by pressing in place Do not damage the O ring Completion NOTE Verify that the ignition key switch is in the OFF position before installing the main fuse 1 See the service manual and install the main fuse NOTES Riding a motorcycle equipped with an exposed oiled air filter under rainy condit
3. arts are intended for THE EXPERIENCED RIDER ONLY REMOVAL NOTE For vehicles equipped with security siren Verify that the Hands Free Fob is present Turn the ignition key switch to IGNITION J05679 Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled 1 For ALL vehicles Remove the seat Retain the seat and all mounting hardware NOTE Verify that the ignition key switch is in the OFF position before removing the main fuse WARNING To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b 2 See the service manual and remove the main fuse 3 Remove the currently installed air cleaner Refer to the service manual or the instructions for THAT air cleaner See Figure 1 Save the two breather screws A from the backplate The remaining parts can be recycled or properly disposed of INSTALLATION Install Air Cleaner NOTE When servicing the air cleaner apply Loctite 243 blue to threads of all fasteners 1 See Figure 1 Install two O rings 1 from kit in grooves around breather screw holes on induction module side of backplate assembly 2 2 Align the holes in the gasket 3 with holes in the back plate and install on the induction module side of the backplate 3 Apply Loctite 243 blue to the threads of the breather screws A saved earlier and the mating tapped holes in the
4. at blade screwdriver in the slot at the bottom of the medallion Carefully work around the center portion without scratching the finish of the air cleaner cover Rotating the medallion will aid in removal b Remove the air cleaner cover center screw c Tap the element to dislodge any loose dirt then gently brush with a soft bristle brush d Spray air filter cleaner liberally onto the cotton filter media and let soak for ten minutes OR roll and soak the cotton filter media in a shallow pan of air filter cleaner Remove immediately and let soak for ten minutes e Rinse off the filter media flowing from the clean side to the dirty side with low pressure tap water f After rinsing shake off all excess water and let the filter media air dry DO NOT use compressed air or a heat gun to speed drying g After the filter media is completely dry EITHER spray air filter oil along each pleat once only holding the spray nozzle approximately 3 inches 76 mm away from the media OR carefully use a squeeze bottle to deposit oil along each pleat once only Let the oil absorb into the filter media for twenty minutes before proceeding After twenty minutes inspect the filter media and carefully apply oil to any remaining visible white spots on the filter media and allow to absorb 20f3 SERVICE PARTS is07397a Figure 1 Service Parts Screamin Eagle Performance Air Cleaner Kit Table 1 Service Parts
5. cMOTOR HARLEY DAVIDSON WY J05679 INSTRUCTIONS REV 2012 11 06 SCREAMIN EAGLE PERFORMANCE AIR CLEANER KIT GENERAL Kit Numbers 29400127 29400128 Models Fits certain XL Sportster models For specific model fitment information see e the P amp A retail catalog e the Screamin Eagle Pro Racing Parts catalog e the Parts and Accessories section of www harley dav idson com English only or e visit www h d com racecatalog Installation Requirements Loctite 243 Medium Strength Threadlocker and Sealant Blue Part No 99642 97 is required for proper installation of this kit AWARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation and is available from a Harley Davidson dealer Proper installation of this kit requires the use of Digital Techni cian by a factory trained technician at a Harley Davidson dealer Kit Contents See Figure 1 and Table 1 NOTE This kit is intended for High Performance applications only Engine related performance p
6. ions IS NOT RECOMMENDED Install the pre charger 13 over the air filter element under these circumstances Recalibrate ECM NOTICE You must recalibrate the ECM when installing this kit Failure to properly recalibrate the ECM can result in severe engine damage 00399b Download the new ECM calibration using the Digital Techni cian at a Harley Davidson dealer Air Filter Element Maintenance 1 Inspect the air filter element every 5000 miles 8000 km or more often under dusty conditions NOTES e The use of cleaning drying or oiling methods or products other than those shown will damage the filter and void the manufacturer s warranty e K amp N Air filter Cleaner is available from a Harley Davidson dealer either alone 1 qt 0 95 L sprayer bottle Part No J05679 99883 88T or a 12 fl 02z 0 35 L sprayer bottle as part of the Filter Care Service Kit Part No 99850 92T K amp N Air Filter Oil is also available from a Harley Davidson dealer either alone 12 25 02 347 gram aerosol can Part No 99882 88T or a 6 5 02 184 gram aerosol can as part of the Filter Care Service Kit DO NOT OVER OIL THE AIR FILTER Over oiling may interfere with the proper performance of the engine and or certain engine components If oil is still draining or dripping from the filter media twenty minutes after oiling clean and oil the filter element again To clean the element a Remove the center medallion by inserting a small fl
Download Pdf Manuals
Related Search