INSTALLATION INSTRUCTION
Contents
1. and front drive shaft pinion relationships as original Be sure to mark left right front rear and indexing of mating parts before disassembly A paint marker or light colored nail polish is handy for this K Suspension components that use rubber or urethane bushings should be tightened with the vehicle at normal ride height This will prevent premature failure of the bushing and maintain ride comfort L Welding on a car creates an electrical charge throughout the body and frame Disconnect the vehicle s battery prior to any welding Place welding ground clamps as near as possible to the weld Never use a vehicle suspension component as a welding ground point M Check off the box M at the beginning of each step when you finish it Then when you stop during the installation it will be easier to find where you need to continue from N The recommended tire size for this suspension system is 315 75 17 The maximum wheel backspacing is 6 inches on 17 wheels Before installing any other combination consult your local tire and wheel specialist Backspacing Negative Offset Mounting Face Diameter WHEEL TERMINOLOGY ne Width O Important information for the end user is contained in the consumer installer information pack If you are installing this system for someone else place the information pack on the drivers seat Please include the installation instructions when you finish P Thank you for purch2. INSTALLATION INSTRUCTION 89450 Rev B Rancho Suspension System RS66450R7 Fits 2003 2013 4WD Dodge Ram 2500 3500 DIESEL MODELS ONLY READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES WARNING This suspension system will enhance the off road performance of your vehicle It will handle differently both on and off road from a factory equipped passenger car or truck Extreme care must be used to prevent loss of control or vehicle rollover during abrupt maneuvers Failure to drive this vehicle safely may result in serious injury or death to the driver and passengers ALWAYS WEAR your seat belts REDUCE your speed and AVOID sharp turns and other abrupt maneuvers A Before installing this system have the vehicle s alignment and frame checked by a certified technician The alignment must be within factory specifications and the frame of the vehicle must be sound no cracks damage or corrosion B Do not install a body lift kit with this suspension system or interchange Rancho components with parts from another manufacturer Included new front Rancho shock absorbers RS7044 are required Matching rear Rancho Shock absorbers RS7269 may be purchased separately C Do not powdercoat or plate any of the components in this system To change the appearance of components automotive paint can be applied over the original coating D Each hardware kit in this system contains fa
3. ack QTY PD FRONT SUSPENSION VEHICLE PREPARATION 1 L Park the vehicle on a level surface Set the parking brake and chock rear wheels Measure and record the distance from the center of each wheel to the top of the fender opening See illustration 1 Illus 1 2 L If equipped remove the front skid plate 3 L Disconnect the track bar from the frame bracket See illustration 2 Illus 2 4 LJ Raise the front of the vehicle and support the frame with jack stands Remove the front wheels and set them aside SHOCK ABSORBER REMOVAL 1 J Support the front axle with a floor jack Secure the axle to the jack to keep it from rotating 2 L Remove the sway bar upper nut retainer and cushion as shown in illustration 3 Illus 3 3 LJ Mark the front differential yoke and drive shaft for installation reference Separate the drive shaft from the differential 4 LJ Remove the mounting bolts holding the front brake hoses to the axle brackets Disconnect the front differential vent hose 5 LJ Remove the nut retainer and bushing from the shock absorber stud in the engine compartment Remove the three nuts from the shock bracket See illustration 4 Remove shock bracket Shock Bracket Illus 4 6 LJ Remove the lower bolt from the axle bracket See illustration 5 Remove the shock absorber from the engine compartment Illus 5 NOTE If a quality heavy duty spring compressor is availa
4. asing the best suspension system available For the best installed system follow these instructions If you do not have the tools or are unsure of your abilities have this system installed by a certified technician RANCHO SUSPENSION IS NOT RESPONSIBLE FOR DAMAGE OR FAILURE RESULTING FROM AN IMPROPER OR MODIFIED INSTALLATION STANDARD BOLT TORQUE SPECIFICATIONS INCH SYSTEM Bolt Size Bolt Size Class 9 8 Class 10 9 5 16 15 FT LB 20 FT LB 30FT LB 35 FT LB 30 FT LB 1 2 13x1 75 HHCS i p DT L X Grade 5 Grade 8 G Grade Marking bolt strength L Length inches D Nominal Diameter inches T Thread Pitch threads per inch T L OO Hz X Description hex head cap scre 5 FT LB 9 FT LB 7116 45 FT LB 60 FT LB 32 FT LB 45 FT LB METRIC SYSTEM Class 12 9 12 FT LB 27 FT LB 50 FT LB 90 FT LB 145 FT LB 210 FT LB 290 FT LB Bam L Length millimeters X Description hex head cap screw 18 FT LB 23 FT LB M12 1 25x50 HHCS a L X P Property Class bolt strength D Nominal Diameter millimeters T Thread Pitch thread width mm P N DESCRIPTION RS176692 Sway Bar Spacer RS860699 Sway Bar Spacer Plate Hardware Kit RS770080 HHCS M10 1 50 X 30mm RS7657 Nut M10 1 50 Nylock RS770064 Washer M10 PARTS LIST P N RS7044 RS824B RS89450 RS94180 ar AN 2 DESGRIPTION RS7000MT Shock Absorber Coil Spring Front Progressive Instruction Information P
5. ble it may be used to remove OE and install Rancho springs Otherwise the suspension arms must be removed to lower axle enough to complete installation COIL SPRING REMOVAL AND INSTALLATION 1 LJ Mark the lower suspension arm cam adjusters and axle brackets for installation reference 2 LI Loosen the upper suspension arm bolts 3 LI Loosen lower suspension arm to frame mounting bolts 4 L Confirm axle is securely supported by floor jack 5 LI Remove the upper suspension arm to axle mounting bolts See illustration 6 Confirm axle is secure and will not flip or rotate 6 LJ Carefully remove lower suspension arm to frame mounting bolts taking care that axle stays level and secure See illustration 6 If axle wants to rotate use another jack under the differential yoke or lower suspension arm Lower Suspension Arm Illus 6 7 LI Mark the coil spring and axle pad for installation reference 8 LI Carefully lower the axle until the coil springs are free from the upper mounts Remove the coil springs CAUTION Do not allow the front axle assembly to hang from the brake hoses 9 L Insert left coil spring between the driver side axle pad and upper mount Carefully lower axle if required Align spring with reference marks 10 LJ Insert right coil spring between the passenger side axle pad and upper mount Align spring with reference marks See illustration 7 Illus 7 11 LJ Carefully raise front axle Do
6. not lift vehicle off frame supports 12 L Reattach upper and lower suspension arms Do not tighten until vehicle is on ground at ride height h 1 1 2 3 SHOCK ABSORBER INSTALLATION Fully extend new Rancho front shock absorber RS7044 Insert shock into coil spring from engine compartment Attach shock to axle bracket with the original hardware Tighten bolt to 100 ft Ibs Install lower retainer and bushing on shock Install shock bracket and the three original nuts Refer back to illustrations 4 and 5 Tighten nuts to 55 ft Ibs Install upper bushing and retainer Install shock absorber nut and tighten to 40 ft Ibs Align reference marks and reattach the front drive shaft with the original hardware Apply thread lock and tighten bolts to 21 ft lbs Reattach the end links to the sway bar with the Original retainers bushings and nut Tighten to 20 ft Ibs Reattach brake hose to the axle bracket with the original bolt SWAY BAR DROP BRACKET INSTALLATION Remove sway bar to frame mounting bolts Install Rancho sway bar drop brackets RS176692 using OE hardware with logo facing out Attach sway bar to Rancho sway bar drop brackets RS176692 using supplied hardware from kit RS860699 See illustration 8 Illustration 8 4 gt L Install front wheels and lower vehicle to ground Tighten the lug nuts to 145 ft Ibs Apply thread lock and tighten the up
7. per link bolts to 120 ft Ibs Install thread lock and tighten the lower link bolts to 160 ft Ibs Apply thread lock and attach track bar to frame bracket If holes to not align have assistant slowly turn wheel to left or right to align Tighten the track bar bolt to 165 ft Ibs FINAL CHECKS amp ADJUSTMENTS 1 Camber not adjustable Sum Toe In degrees LI Turn the front wheels completely left then right Verify adequate tire wheel and brake hose clearance Inspect Steering and suspension for tightness and proper operation Readjust headlamps certified alignment facility Have vehicle aligned at a Recommended Alignment Specifications Preferred Range Caster degrees 025 gt Please retain this publication for future reference See Important Note P
8. steners of high strength and specific size Do not mix hardware kits or substitute a fastener of lesser strength See bolt identification table on page 2 E Compare the contents of this system with the parts list in these instructions If any parts are missing contact the Rancho Technical Department at 1 734 384 7804 F Install all nuts and bolts with a flat washer When both SAE small OD and USS large OD washers are used in a fastener assembly place the USS washer against the slotted hole and the SAE washer against the round hole G Apply a drop of thread locking compound to all bolts during installation CAUTION Thread locking compound may irritate sensitive skin Read warning label on container before use H Unless otherwise specified tighten all nuts and bolts to the standard torque specifications shown in the table on page two USE A TORQUE WRENCH for accurate measurements Some of the service procedures require the use of special tools designed for specific procedures The following tools and supplies are recommended for proper installation of this system M Dodge Service Manual Bench Vise Torque Wrench 250 FT LB capacity 1 2 Drive Ratchet and Sockets Assorted Combination Wrenches Heavy Duty Jack Stands Wheel Chocks wooden blocks Hydraulic Floor Jack Hammer Tape Measure Safety Glasses wear safety glasses at all times I DD DEE J It is extremely important to replace torsion bars CV flanges
Download Pdf Manuals
Related Search