Home
2045 LX Centrifugal Pump - QUINCIE Oilfield Products
Contents
1. have been assembled stand this assembly upright and install pump housing 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP 15 GARDNER DENVER Bolt rear bearing cover to pump housing but do not tighten bolts qty 4 P N 17519 at this time 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP Install slinger but do not tighten lock screw at this time Gp GARDNER DENVER P N 17522 5 8 11 x 5 8 P N 29810 Soc Set Cup Pt Slinger 2 Piece 28 2045 LX Centrifugal Pump GARDNER DENVER 625 OLD DIMENSION ANY PUMP THAT IS PACKED WITH THREE SEALS AND HAS THE PACKING GLAND follower WITH THE 625 DIMENSIONS INDICATED BY DOTTED LINES LEFT SHOULD BE MODIFIED TO THE 125 DIMENSION AND 4 SEAL ADDED AS SHOWN ON PAGE 30 125 NEW J DIMENSION P N d Bracket for 2 piece fo P N 27981 P N 29811 Packing Follower Solid Packing Follower 2 Piece 20 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP Gp Modify as DSG ee Turn this seal around to position shown Install seals 4 lantern gland and modified f packing gland into stuffing box in backhead as indicated above Note Lubricate O D of seals before instal lation and observe placement of number 3 seal as the lip on this seal must face rear of pump GARDNER DENVER 2045 LX Centrifugal Pump TYPICAL INSTALLATION OF CENTRIFUGAL PUMP PACKING
2. GARDNER DENVER IMPELLER LUBRICATION PORT PLIT SEAL RINGS GLAND FOLLOWER 2 PC AM N pk SS Ter SEAL RINGS S N I R I SPLIT COMPRESSION Ai o PES PACKING RING NN ASAK GN LAN 2045LX REPLACEMENT PACKING SET PART NO SET OR COMPONENTS TUL 29909 I gt COMPLETE SET 2 PRIMARY MOLDED SPLIT SEAL RINGS LANTERN RING SPLIT SEAL RINGS SHAFT NN fDANTERN RING 29796 I SPLIT COMPRESSION NOW PLASTIC PACKING RING _ STUFFING BOX HE FOLLOWING ITEMS ARE NOT A PART OF THIS REPLACEMENT 2 SSG GN ON AREA SET AND THEREFORE MUST BE PURCHASED SEPARATELY SHAFT BACKHEAD GLAND FOLLOWER 2 N KEEPER BOLT IMPELLER LUBRICATION PORT i BOLT BACKHEAD REMOVE ALL WORN PACKING RINGS FROM THE STUFFING BOX AND CLEAN SAME THROUGHLY 2 CHECK ALL BEARINGS PER THE MANUFACTURERS SPECIFICATIONS AND REPLACE SAME IF NECESSARY CHECK THE SHAFT AND REPLACE IF NECESSARY 3 LUBRICATE THE 2 PRIMARY SEAL RINGS INSTALL AND SEAT EACH SEAL RING SEPARATELY WITH ALL SEAL LIPS FACING TOWARD THE IMPELLER STAGGERING THE SPLITS AT THE 12 O CLOCK AND THE 3 O CLOCK POSITIONS SO THAT THERE IS NO DIRECT LEAKAGE PATH ESTABLISHED 4 LUBRICATE AND INSTALL THE 2 PIECE PLASTIC LANTERN RING 5 LUBRICATE THE 2 SECONDARY SEAL RINGS INSTALL AND SEAT EACH SEAL RING SEPARATELY AND AGAIN STAGGERING THE SPLITS AS FOLLOWS a THE 19 SECONDARY SEAL RING OF THIS SERIES MUST BE
3. GARDNER DENVER Remove back head 2045 LX Centrifugal Pump GARDNER DENVER DISASSEMBLY OF LX PUMP Gr Remove two bolts from Packing Gland 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP GD GARDNER DENVER Remove packing gland follower This will give access to seals and lantern gland which may be removed from stuffing box at this time Check all parts for wear Caution Take care when removing seals to prevent damage to seals and lantern gland 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP GARDNER DENVER Before proceeding further with disassembly remove this grease fitting 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP G gt GARDNER DENVER Remove Slinger locking screw 12 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP Remove slinger 13 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP GARDNER DENVER Remove these bolts 4 Pick pump up and bump Impeller end of shaft against a heavy block of wood This will remove shaft bearings and rear bearing retainer as an assembly 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP GD GARDNER DENVER Rear bearing retainer shaft and both bearings should slip out of the pump housing as an assembly If the front bearing becomes disengaged from shaft and remains in the housing it may be removed with the proper tooling 2045 LX Cen
4. any product or part thereof which in the Company s judgment is proved not to be as warranted Labor shall be limited to the amount specified in the Company s labor rate schedule Labor costs in excess 48 2045 LX Centrifugal Pump of the Company rate schedules caused by but not limited to location or inaccessibility of the equipment or labor provided by unauthorized service personnel is not provided for by this warranty All costs of transportation of product or parts claimed not to be as warranted and of repaired or replacement parts to or from such service facility shall be borne by the Purchaser The Company may require the return of any part claimed not to be as warranted to one of its facilities as designated by the Company transportation prepaid by the Purchaser to establish a claim under this warranty Replacement parts provided under the terms of this warranty are warranted for the remainder of the Warranty Period of the product upon which installed to the same extent as if such parts were original components The Company may request a root cause analysis be performed in order to identify if a request for warranty claim meets the requirements of this warranty DISCLAIMER Except as to title the foregoing warranty is the sole and exclusive warranty of the Company The Company hereby extends other manufactures warranty or guaranties if any given to Company by such manufacturer but only to the extent the Com
5. limited to valves valve parts packing liners and pistons are not covered by this warranty due to variable abrasive nature of material pumped PRESERVATION ASSEMBLIES DESTINED FOR STORAGE In order for warranty acceptance any pump assembly not immediately installed or destined to be in storage or in transit for extended periods of time must be prepared for storage as defined in the Company s Long Term Storage Procedure This includes but is not limited to Drain and thoroughly clean inside power end crankcase Spray rust inhibiting oil on all bearing machined and inside surfaces of the power end Induce clean gear oil into any circulating pump filter heat exchanger and piping Remove valves seats and plungers from the fluid end Thoroughly clean and dry these parts and all internal surfaces Coat all cylinder bores valve covers and reusable expendable parts with rust preventative Flush all water and contaminants from pump tanks hoses and spray nozzles Spray all components with a rust inhibiting oil Rotate pump every 30 days to insure bearings are oiled At the expense of the Purchaser any product properly preserved must be inspected by an authorized agent of the Company prior to the Company granting any extended warranty beyond that stated in this warranty LABOR TRANSPORTATION AND INSPECTION The Company will provide labor by Company representative or authorized service personnel for repair or replacement of
6. services INSTRUCTIONS FOR ORDERING REPAIR PARTS e When ordering parts specify Pump MODEL and SERIAL NUMBER see name plate on unit e All orders for Parts should be placed with the Tulsa or Ft Worth facility e Specify exactly the number of parts required 51 K ame s Drilling amp Production Pumps Gardner Denver Pump Division 1800 Gardner Expressway Quincy IL 62301 Phone 217 222 5400 Fax 217 223 1581 Drilling amp Production After Market Gardner Denver Pump Division 2200 South Prospect Oklahoma City OK 73129 Phone 405 677 5736 Fax 405 677 5807 Well Service Pumps Gardner Denver Pump Division 4747 South 83rd East Avenue Tulsa OK 74145 Phone 918 664 1151 Fax 918 447 6487 Le m ay 1 j GEOQUIP SERVICE CENTER After Market amp Repair Facility Gardner Denver Pump Division 7533 Kathy lane Fort Worth TX 76126 Phone 817 249 6400 Fax 817 249 6383 B Bi FE d e I i m C A US a 1 F Ux CHAPARRAL SERVICE CENTER After Market amp Repair Facility Gardner Denver Pump Division 2121 West 44th Street Odessa TX 79764 Phone 432 366 5433 Fax 432 363 9940
7. shortened flow path development of full pressure at 1 3 revolution of impeller distribution of wear at three points prevention of air entrapment and vapor lock reduction of shear and improvement of viscosity handling characteristics e The GD 2045 LX drive system has a mounting adapter bracket predrilled to accept a direct drive SAE C two or four bolt hydraulic motor and in conjunction with our internal splined shaft eliminates down time due to misalignment e Simplistic construction requires less assembly time and less spare parts inventory e The impeller design is fully open and ideally suited for handling fluids containing suspended solids Impeller is available in an 8 vane pattern with a clockwise rotation e The frame is available in two versions economical cast iron and steel fabricated e The GD 2045 LX offers two packing choices Solid lip seals provide efficient service with a minimum amount of attention Split compression type packing is available for more severe service conditions and can easily be replaced without dismantling the pump e Bearings provide maximum radial and thrust load capacity and are protected by a water slinger HYDRAULIC MOTOR MOUNTING SPECIFICATIONS PERFORMANCE CURVES FRAME AND SPLINE DATA FOR SAE C TWO 2 OR FOUR 4 BOLT HYDRAULIC MOTOR MALE SPLINE INFORMATION 1 250 O D H Cae 14 TOOTH FLAT ROOT SIDE FIT do D 30 PRESSURE ANGLE 1 1667 PITCH DIA 9 12 24 DIA PITCH 400 200 300
8. 02 Lock Impeller Bolt Impeller 39 2045 LX Centrifugal Pump Gaz GARDNER DENVER ASSEMBLY OF LX PUMP Entire rotating assembly may now be inserted into volute Use mounting pedestals for proper alignment Install housing nuts and torque to 150 20 Ib ft I200 25 Nm Volute P N 5620LR 40 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP G GARDNER DENVER Screw Lube pipe with cap into backhead P N 14724 Lube Pipe w Cap 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP G GARDNER DENVER Install grease zerk P N 17516 2045 LX Centrifugal Pump IMPORTANT THIS PROCEDURE MUST AJ DONE FOR PUMP TO OPERATE GARDNER DENVER TO DESIGN For proper pump performance and long life it is extremely important that these adjustments be made with care as this will assure the proper 030 clearance between the Impeller and Volute Measure this distance Turn all adjusting screws counter clockwise until they are flush with front face of rear bearing retainer housing Drive bearing retainer forward until Impeller contacts Volute Turn adjusting screws clockwise until they contact pump housing Turn each adjusting screw 1 4 turn Continue in this manner until the initial distance plus 030 is reached Torque retainer bolts to 75 10 Ib ft 100 15 Nm He measure distance between pump housing and rear bearing ret
9. 2045 LX Centrifugal Pump 2045 LX Centrifugal Pump GARDNER DENVER LX PUMP ASSEMBLY 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP Less GARDNER DENVER To disassemble pump first remove nuts 12 where indicated around entire perimeter of pump housing 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP Less GARDNER DENVER After 12 nuts are removed entire rotating assembly may be pulled out of volute as shown above using the push bolt holes as necessary Note Due to cement build up between Volute and pump housing it is sometimes difficult to remove rotating assembly 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP Less GARDNER DENVER 1 indies i T 4 Hemove Impeller retaining bolt 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP GU GARDNER DENVER Use puller to remove impeller from shaft 2045 LX Centrifugal Pump GU GARDNER DENVER DISASSEMBLY OF LX PUMP e fe a Remove pipe nipple from stuffing box After Impeller and pipe nipple are removed remove Impeller key from shaft with proper tool being careful not to damage shaft Note his key is specific finish tolerances Check for burrs wear nonconformance to shaft keyway Replace if needed DISASSEMBLY OF LX PUMP a i Ze i 1 P ENS DEN INT au NE A SS DET A s
10. 400 500 600 700 800 900 1000 1100 1200 GALLONS PER MINUTE WT 340 LBS SASA 150 FLANGE ON 6 ASA 150 FLANGE 7197 Bs 2 DRAIN PLUGS 8 BOLTS 3 4 ON Bo DETAIL A 3 12 B C 2 HOLES 1116 2 HOLES ee 1 ONT7 12 B C 11 16 4 HOLES 9 16 ON 6 38 2045 LX Centrifugal Pump Ref No B QD ch DA 8A 10 11 12 13 14 15 16 17 2045 LX Parts List Name of Part GASKET DISCHARGE SET SCREW IMPELLER BOLT Hex Design IMPELLER LOCK WITH ROLL PIN SPLIT LIP SEAL PACKING RING OIL SEAL SOLID PACKING LANTERN GLAND 2 PIECE LANTERN GLAND SOLID SQUARE COMPRESSION PKG RING PACKING FOLLOWER 2 PIECE PACKING FOLLOWER SOLID KEEPER HEX BOLT Pkg Follower Backhead BEARING INBOARD SINGLE ROW RETAINING RING INBOARD IMPELLER KEY SHAFT INTERNAL SPLINED DRIVE GREASE ZERK RETAINING RING OUTBOARD BEARING OUTBOARD Double row Qty Part No 1 35193 1 28775 1 56102 1 56103 4 29795 3 or 4 5826 1 29797 1 29782 1 29796 1 TUL29811 1 29781 2 29812 2 103284 1 TUL52480 1 52481 1 26083 1 61088 1 17516 1 26035 1 61116 47 Ref No 18 19 20 21 21A 22 23 24 25 26 27 28 29 30 31 32 33 34 GARDNER DENVER Name of Part BEARING LOCK NUT OIL SEAL OUTBOARD GASKET SUCTION VOLUTE MODIFIED VOLUTE NO PED ESTALS WITH EX DRAIN 1 PIPE PLUG 1 2 PIPE PLUG GASKET BACKHEAD IMPELLER 8 VANE O R
11. ING BACKHEAD BACKHEAD LUBE PIPE WITH CAP RETAINING SCREW SLINGER SHAFT SLINGER 2 PIECE FRAME CAST HEX BOLT FRAME VOLUTE HEX BOLT BEARING COVER FRAME THRUST AJUSTMENT SCREW BEARING COVER amp MOTOR BRACKET Part No 61117 62961 35264 5620LR 5620LR SP 17520 16125 24766 74814 17449 26081 14724 17522 29810 TUL62960 17515 17519 26029 26084 These items not shown on this assembly drawing 2045 LX Centrifugal Pump GENERAL PROVISIONS AND LIMITATIONS Gardner Denver the Company warrants to each original retail purchaser Purchaser of its new products assemblies or parts from the Company or its authorized distributors that such products are at the time of delivery to the Purchaser made with good material and workmanship No warranty is made with respect to 1 Any product which has been repaired or altered in such a way in the Company s judgment as to affect the product adversely 2 Any product which has in the Company s judgment been subject to negligence accident or improper storage improper installation operation or application Examples over pressure sand outs cavitation corrosion erosion or degradation 3 Any product which has not been operated or maintained in accordance with the recommendations of the Company 4 Components or accessories manufactured warranted and serviced by others Any reconditioned or prior owned product Claims for i
12. INSTALLED WITH THE LIPS FACING AWAY FROM THE IMPELLER WITH SPLITS AT THE 6 O CLOCK POSITION THE REVERSE POSITION OF THIS SEAL WILL PREVENT AIR FROM BEING DRAWN THRU THE GLAND AND THUS CAUSING THE LOSS OF PRIME b THE 2 SECONDARY SEAL RING OF THIS SERIES MUST BE INSTALLED WITH THE SEAL LIPS FACING THE IMPELLER AND WITH THE SPLIT AT THE 9 O CLOCK POSITION 7 LUBRICATE INSTALL AND SEAT THE SPLIT COMPRESSION PACKING RING WITH THE SPLIT AT THE 12 O CLOCK POSITION 8 PROPERLY PRELOAD THIS COMBINATION SET BOTTOM OUT THE FLAT SIDE OF THE GLAND AGAINST THE FACE OF THE STUFFING BOX 3l 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP KE GARDNER DENVER P N TUL29909 Packing Kit OCOOC va we P N 29797 6 Split Seal Packing Lantern 2 Piece items 1 2 4 5 item 3 P N 29796 Sq Pkg Ring 6 Solid Packing 00000 P N 5826 P N 29782 Solid Packing Lantern Solid items 1 2 4 5 item 3 P N 29796 Sq Pkg Ring item 6 P N 29812 Bracket for 2 piece fo P N 27981 P N 29811 Packing Follower Solid Packing Follower 2 Piece 32 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP Gr GARDNER DENVER Packing Kit P N 26081 Backhead Install Packing in stuffing box area of backhead as directed on page 31 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP Less GARDNER DENVER Install Packing Gland Follower Install Packing gland bolts and tighten to 60 Nm 10 A light c
13. PARTS AND SUPPORT SERVICES GARDNER DENVER For the location of your local authorized Gardner Denver distributor refer to the yellow pages of your phone directory or contact Factory Tulsa Gardner Denver Well Servicing Pumps 4747 South 83 East Ave Tulsa Oklahoma 74145 Phone 918 664 1151 800 637 8099 Fax 918 664 6225 Service Center Odessa Chaparral 2121 West 44 Street Odessa TX 79768 Phone 432 366 5433 800 368 1134 Fax 432 363 9940 Service Center Ft Worth Geoquip 7533 Kathy Lane Ft Worth Texas 76126 Phone 817 249 6400 800 824 0271 Fax 817 249 6383 Gardner Denver genuine pump parts are manufactured to design tolerances and are developed for optimum dependability Design and material innovations are the result of years of experience with hundreds of different pump applications Reliability in materials and quality assurance is incorporated in our genuine replacement parts Gardner Denver supports your needs with these services e Large inventory of genuine parts in stock and ready to ship e Trained parts specialists to assist you in selecting the correct replacement parts e Repair and maintenance kits designed with the necessary parts to simplify servic ing your pump e Authorized service technicians are factory trained and skilled in pump mainte nance and repair They are ready to respond and assist you by providing fast ex pert maintenance and repair
14. ainer as it sometimes will change when retainer bolts are torqued oome early pumps will have two 2 adjusting screws and two 2 retainer bolts while later models may have four 4 adjusting screws and four 4 retainer bolts This does not affect adjusting procedure 43 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP G gt GARDNER DENVER After pump has been installed and adjusted adjust slinger toward rear of pump until it contacts front bearing and tighten lock screw 44 2045 LX Centrifugal Pump AR Gaz GARDNER DENVER ASSEMBLY OF LX PUMP Remove this plug install vent here Bottom pipe plug Install grease fitting here Grease level pipe plug Side Plug After pump has been overhauled remove pipe plug in bottom of pump housing and install grease fitting Remove pipe plug on side of housing Pump NGL 1 or NGL 2 chassis lube into housing until it starts to come out of hole in side of housing where pipe plug was removed While grease is being pumped into housing pump should be turning as this will distribute lube to bearing and prevent over filling 45 2045 LX Centrifugal Pump GARDNER DENVER DESIGN FEATURES GIVE Em LONG LIFE amp EASY MAINTENANCE e The 2045 LX features two flow dividers resulting in AJ three throats positioned 120 degrees apart which GARDNER DENVER allows for a balance of thrust and forces and low radial loads
15. eads or pressure headers mudpumps centrifugal and slurry pumps and 5 to 8 stage centrifugal pumps heat exchanger tube bundle welding amp refacing etc Our specialty Turn around work MISCELLANEOUS MACHINING MILLING amp BORING TURNING TO 42 DIA FABRICATION WELDING COMPLETE FIXTURE amp TOOLING DEPARTMENT HYDROSTATIC amp DESTRUCTIVE TEST FACILITY SHOT PEENING amp STRESS RELIEVING 75 000 P S l AUTOFRETTAGE FACILITY 50 GARDNER DENVER CENTRIFUGAL PUMP APPLICATIONS GARDNER DENVER OTHER GARDNER DENVER PRODUCTS HIGH PRESSURE TRIPLEX PUMPS FOR ACIDIZING amp FRACTURING FEATURES STEEL FABRICATED POWER FRAME SOLID ONE PIECE CONNECTING ROD PRECISION GROUND CROSSHEADS FORGED ALLOW STEEL CRANKSHAFT HIGH GRADE ALLOY STEEL GEARS FOUR MAIN ROLLER BEARINGS ORIFICED LUBRICATION SYSTEM LIGHTWEIGHT ALUMINUM COVERS INTERCHANGEABLE PARTS STOCK HIGH PRESSURE FLUID ENDS FROM SOLID STEEL FORGINGS FEATURES UNIFORMITY OF ALL INTERNAL SURFACES ALL CORNERS CENEROUSLY REDIUSED ALL BORES HAND POLISHED SHOT PEENED AUTORETTAGE CAPABILITY CUSTOM DESIGNS MADE ON CONTRACT BASED UPON RECEIPT OF SPECIFICATIONS AND DRAWINGS STANDARD REPLACEMENT CAN BE PROVIDED FOR MOST PUMPS ON THE MARKET SPECIAL MATERIALS AND OR SPECIFIC MODIFICATIONS MAY BE INCORPORATED INTO MOST STANDARD DESIGNS 2045 LX Centrifugal Pump MAINTAIN PUMP RELIABILITY AND PERFORMANCE WITH GENUINE GARDNER DENVER
16. lution is to cut motor shaft or splined end of pump shaft off with a torch 20 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP G GARDNER DENVER Reassembly of pump should begin with the replacement of seal in rear bearing cover Seal lip should face to the rear of housing away from rear bearing This prevents any foreign material from entering rear bearing assembly P N 26084 P N 62961 Bearing Cover Oil Seal Outboard 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP Less GARDNER DENVER Rear Bearing Lock Nut Outboard Bearing Install rear bearing and lock nut P N 61116 P N 61117 Outboard Bearing Locknut Bearing P N 61088 Shaft Internal Spline 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP 708 1 i i 4 Insert the shaft and rear bearing into bearing cover GU GARDNER DENVER 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP 5225 GARDNER DENVER Install front inboard bearing snap ring Install rear Outboard bearing retaining ring P N 26035 P N 52481 Retaining Ring Outboard Retaining Ring Inboard 24 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP GARDNER DENVER Install front inboard bearing P N TUL52480 Inboard bearing 25 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP GD AT GARDNER DENVER When shaft bearings P N TUL 62960 and rear bearing cover
17. oating of chassis lube should be applied to the of seal assembly at this time 34 2045 LX Centrifugal Pump GU GARDNER DENVER ASSEMBLY OF LX PUMP p N17449 Cover the seal area of f O Ring Backhead the shaft with a light coating of chassis lube and install backhead gasket and O ring P N 24766 Gasket Backhead P N 26081 Backhead 35 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP Pj GARDNER DENVER B Install backhead assembly as shown above using guide pin for proper alignment Caution Be extremely careful when the 3 seal contacts shaft as the lip on this seal points in the opposite direction of the other three 3 seals and serious damage can result to seal lip or compression spring may become disengaged Install Impeller Key at this time Caution This Key is special and a standard Woodruff Key will not fit P N 26083 Impeller Key 37 2045 LX Centrifugal Pump Gaz GARDNER DENVER ASSEMBLY OF LX PUMP Install Impeller over shaft and key being very careful that key does not become disengaged from shaft P N 74814 Impeller 8 Vane 2045 LX Centrifugal Pump ASSEMBLY OF LX PUMP GARDNER DENVER a r ER a Install impeller lock and bolt as shown above and torque bolt to 200 15 Ib ft 280 20 Nm Install set screw as shown above P N 28775 Set Screw Impeller Bolt is P N 56103 P N 561
18. pany is able to enforce such warranty or guaranties The Company has not authorized any party to make any representation or warranty other than as expressly set forth herein SELLER HEREBY DISCLAIMS AND EXCLUDES ANY OTHER EXPRESS IMPLIED OR STATUTORY WARRANTIES ARISING BY OPERATION OF LAW OR OTHERWISE INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE COMPANY MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER EXPRESS IMPLIED OR STATUTORY OF LAW OR OTHERWISE ON ANY EQUIPMENT COMPONENT PARTS OR ACCESSORIES SOLD HEREUNDER WHICH ARE NOT MANUFACTURED BY COMPANY NOTWITHSTANDING ANYTHING HEREIN TO THE CONTRARY THE FOREGOING WARRANTY SHALL BE THE SOLE AND EXCLUSIVE REMEDY AVAILABLE TO THE PURCHASER UNDER NO CIRCUMSTANCES WHETHER IN CONTRACT TORT OR OTHERWISE SHALL THE COMPANY S TOTAL LIABILITY ARISING IN GARDNER DENVER PRODUCT WARRANTY GARDNER DENVER CONNECTION WITH ANY PURCHASE ORDER EXCEED THE AMOUNT OF ANY SALES OR OTHER PROCEEDS RECEIVED PURSUANT THERETO IN ADDITION UNDER NO CIRCUMSTANCES WHETHER IN CONTRACT TORT OR OTHERWISE SHALL THE COMPANY BE LIABLE FOR LIQUIDATED SPECIAL INDIRECT INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES EXPENSES OR COSTS INCLUDING WITHOUT LIMITATION LOST PROFITS OR FACILITY DOWNTIME HOWEVER CAUSED AND EVEN IF THE POTENTIAL OF SUCH DAMAGES WAS DISCLOSED AND OR KNOWN No statement representation agreement or unde
19. rstanding oral or written made by any agent distributor representative or employee of the Company which is not contained in this Warranty will be binding upon the Company unless made in writing and executed by an officer of the Company This warranty shall not be effective as to any claim which is not presented within 30 days after the date upon which the product is claimed not to have been as warranted Any action for breach of this warranty must be commenced within one year after the date upon which the cause of action occurred Any adjustment made pursuant to this warranty shall not be construed as an admission by the Company that any product was not as warranted WARRANTY REQUESTS Products to be returned for warranty analysis shall be approved for return in writing by the Company prior to shipment All requests for product return shall be submitted by email Facsimile or letter to Warranty Department c o Gardner Denver Petroleum Pumps 4747 South 83 East Avenue Tulsa Oklahoma 74145 Email CCR QAR gardnerdenver com Facsimile 918 664 6225 49 2045 LX Centrifugal Pump OILFIELD BLENDERS MIXERS CIRCULATION SUPERCHARGING DESANDING TRANSFER WATER FLOOD DISPOSAL WELLS WASHDOWN INDUSTRIAL SLURRY DESANDING MIXING TRANSFER FOOD PROCESSING CHEMICAL PROCESSING IRRIGATION MINING OTHER GARDNER DENVER SERVICES OVERHAUL AND OR REWORK OF Damaged or worn out frac power frames fluid ends crossh
20. tems described in 4 above should be submitted directly to the manufacturer WARRANTY PERIOD The Company s obligation under this warranty is limited to repairing or at its option replacing during normal business hours at an authorized service facility of the Company any part or assembly which in the Company s judgment proved to have unsatisfactory material or workmanship within the applicable Warranty Period as follows Except for the products or components listed below and subject to the limitations and restrictions set forth in the Disclaimer section set forth below the Warranty Period for all products is 1 250 hours of operation or three 3 months after start up not to exceed 120 days after delivery to Purchaser whichever occurs first The exceptions are as follows 1 Power end is warranted for twelve 12 months from date of start up or eighteen 18 months from date of delivery to the Purchaser whichever occurs first 2 Forged steel fluid cylinders are warranted for materials and workmanship for 6 months from GARDNER DENVER PRODUCT WARRANTY GARDNER DENVER the date of installation or 18 months from the date of delivery to the purchaser which ever occurs first 3 Repairs are warranted for 90 days from the date of delivery for the workmanship and materials of the new parts installed 4 Weld repaired fluid ends and weld repaired components are not warranted 5 Expendable fluid end parts including but not
21. trifugal Pump DISASSEMBLY OF LX PUMP G GARDNER DENVER Remove internal snap ring from rear bearing retainer 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP 525 GARDNER DENVER Remove shaft and bearing s from rear bearing retainer 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP GARDNER DENVER Check this area thorougly Shaft should be replaced if worn more than 010 where seals have contacted shaft or if any nicks or roughness are found Remove nut and lock from rear of shaft Bearing may be pressed off at this time 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP 5225 GARDNER DENVER Remove rear seal 2045 LX Centrifugal Pump DISASSEMBLY OF LX PUMP KE Check this area inside shaft for wear SUN GARDNER DENVER Hydraulic 2 Motor Shaft 7 JE Severe wear may occur to pump shaft at point where splines of hydraulic motor contact shaft splines Since It may not be possible to see this wear from the outside of shaft the internal splines in shaft should be cleaned thoroughly with solvent and then inspected under a strong light If the wear in this area exceeds 030 shaft should be discarded and no attempt to reuse or repair should be made When splines become worn beyond the 030 limit it becomes difficult and sometimes impossible to disengage hydraulic motor from pump shaft If this occurs the only so
Download Pdf Manuals
Related Search
Related Contents
Vantage microRNA Detection Kit Guide d`expression - Nantes Just Imagine manuale utente S200 - MEI`s Technical Support Sony Radio ICF-SW7600 User's Manual Raidsonic IB-AC515 Monitor de polvo MANUAL DE USUARIO EC type-approval certificate UK/0126/0131 Revision 2 Canon A800 Camcorder User Manual リーフレット(pdf:620KB) Copyright © All rights reserved.
Failed to retrieve file