Heart Breaker 280 Conversion
Contents
1. Heart Breaker 280 Conversion Fits Breakout Model Softails Instruction We recommend that you mock up bike before you paint parts We also recommend that you lower the bike to achieve the desired look PARTS LIST Heartbreaker 280 Conversion Includes Solo Seat Struts Fender Steel Rock Guard Light Brackets Hardware 20mm Belt Solo Seat Fender o M E EE ec OOOO rrr Left Rock Guard Right Rock Guard 20mm Belt Light Brackets Rock Guard Bolts Strut and Fender Bolts 17171 S Western Ave Gardena CA 90247 Ph 310 822 2697 Fax 310 822 3687 www heartlandbiker com We recommend reading through the entire install process before beginning 2 Disconnect the rear light wiring harness Once the plug is disconnected you can unbolt the struts and remove the strut fender assembly as one unit 5 Grind down caliper perch Use the template on last page as a guide Before Grind down caliper perch along this line using the template on last page as a guide 6 Remove Outer and Inner Primary Covers to install supplied 20mm belt Refer to Harley Davidson Factory Service Manual 7a Now you will begin to install your Heart Breaker Conversion starting with the Steel Rock Guard Slide the left half of the rock guard into the proper position The Welded tabs should align 8b Install brake caliper bracket with supplied wheel spacers over the holes of the swingarn Spacers come2. with wheel 7b With the hardware provided screw each bolt in You may want to check the exact position before tightening Use Blue Loctite Repeat step 5 amp 6 to install right half of the rock guard PT ga Tape wheel to protect from scratching Install eme wheel at a slight angle to clear caliper perch 8c Install rear wheel axle I d 9a The easiest way to assemble the fender and struts is off the bike on a table Using a soft cloth underneath set the fender upside down and lay out the struts next to it Bolt each strut to the fender If you are planning to run rear turn brake indicators now is the time to install them The wires for the turn signals are meant to rest inside the struts in the wire groove and held in place by the fender 2 9c Feed the wires through the small hole from the inside out 9d Push the wires into the channel on the inside of the strut You may want to use tape to hold wires in place while bolting the strut to the fender Make sure there is no slack in the wire and that it is not pinched Template for Step 5 10 Now that the struts are mounted to the fender you will bolt them to the frame Using the hardware provided REMOVE 2 i screw each bolt in to the frame loosely When tightening the THIS AREA bolts start by snugging them down and then torque the rear bolts first followed by the front bolts N i i i i i l D i 4 st a H N Tri gt lt
3. ui I 11 Install new supplied seat by starting at the nose and l making sure the tongue is fitting in the frame Then slowly l bring the seat down while checking clearance The seat J should not interfere with anything in the battery box Push 4 back of seat to activate the suction cup Make sure the suction 4 i cup release tab is pointing upwards for easy removal 4 i Se I Ve 1 1 l CUT OUT i t l f We recommend that you lower the rear of the bike to d achieve the desired look S i ia a CS E BREAKOUT BILLET TEAR WIRING 3 FUNCTION RUN TURN BRAKE NEED Contact Pins 20 01 gauge Harley Part 74191 98 6 pcs TURN SIGNALS Left Side Right Side Side e Black Black e Black Black e Red Blue Purple Red Blue Black e Orange Blue e Orange Blue PLATE HOLDER W BRAKE WIRING 2 FUNCTION RUN BRAKE NEED Deutsch 6 way socket Housing Harley Part 72116 94BK pc Locking cap Harley Part 72156 94 pc Contact pins 16 18 gauge Harley Part 72191 94 3pcs e Black Black e Red Blue Red e Orange Red Yellow
Download Pdf Manuals
Related Search