Home
SXS500M2: Back Up Alarm
Contents
1. 2 HONDA INSTALLATION INSTRUCTIONS Accessory PARTS LIST a 3 Back up alarm harness sold separately ACCESSORY SUB HARNESS Sold separately P N 08Z08 HL5 A00 The Accessory Sub Harness is required for the installation of this accessory Accessory sub harness 2014 Honda Motor Co Ltd All Rights Reserved BACK UP ALARM P N 08V70 HL5 A00 BACK UP ALARM HARNESS P N 08V71 HL5 A00 Application Publication No Issue Date TOOLS AND SUPPLIES REQUIRED Scissors SXS500M2 TORQUE CHART Tighten all screws bolts and nuts to their specified torque values Refer to the Service Manual for the torque values of the removed parts USE AND CARE INFORMATION Check accessory mounts frequently and retighten if necessary Trim all excess material on wire ties no shorter than 5 mm INSTALLATION 1 Refer to the Service Manual for the vehicle and remove the following components in the following order e Rear fender carrier center cover as an assembly e Battery cover e Air cleaner housing e Seat cushion and backrest e Seat bottom cover right and left e Seat rear cover e Rear floor cover e Front floor plate e Front hood 2 Refer to the Service Manual for the vehicle and disconnect negative battery cable 08V70 HL5 A00 amp 08V71 HL5 A00 3 Install and connect the back up alarm harness between the two halves of the gear position switch connector as show
2. n BACK UP ALARM HARNESS TO ALARM BUZZER GEAR POSITION SWITCH 8P Gray BACK UP ALARM HARNESS CONNECTOR Harness side NNECTOR T EAR oe CONNECTOR Engine Side Release from its mounting clip and then disconnect Secure connector body to panel with the clip GEAR POSITION SWITCH CONNECTOR HARNESS SIDE oe ALARM BACK UP ALARM ACCESSORY HARNESS SUB HARNESS Sold separately i GEAR POSITION ta SWITCH CONNECTOR ENGINE SIDE 2 of 6 4 Follow the main harness down Secure the back up alarm harness to the main harness with wire ties near the back of the engine under the passenger seat as shown NOTE Secure the alarm harness only to the main harness Do not wire tie any control cables 5 Follow the main harness going up Secure the back up alarm harness to the main harness with wire ties along the front right side of the vehicle as shown RIGHT HEADLIGHT MAIN HARNESS BACK UP ALARM HARNESS a WZ WIRE TIE FRONT SHOCK ABSORBER 6 Locate the DLC 4P Red connector and remove the dummy cap Be sure to leave the black tape around the connector body harness side lt VIEW UNDER FRONT HOOD gt DLC 4P Red CONNECTOR 4of6 Connect the accessory sub harness to the DLC 4P Red connector Connect the back up alarm harness to the red tape wire of the accessory sub harness as shown e Note that only one connector of the accessory sub harness is used for the back up alarm the remaini
3. ng connectors are for other accessories Secure any excess harness to the frame with wire ties lt VIEW UNDER FRONT HOOD gt G ACCESSORY SUB HARNESS BACK UP ALARM HARNESS MAIN HARNESS H y WIRE TIE _ DLC Main harness RED TAPE c B E BACK UP ALARM WORK LIGHT LED LIGHT ACCESSORY SUB HARNESS 5 of 6 8 Install the back up alarm buzzer to the location shown Back up alarm buzzer installation 8 mm FLANGE BOLT Reinstall ALARM BUZZER 8 mm FLANGE BOLT Remove 9 Connect the back up alarm buzzer connector to the back up alarm harness 10 Reconnect the negative battery cable 11 Start the engine and then select reverse to confirm the performance of the back up alarm e Troubleshoot any problems if necessary 12 Refer to the Service Manual reinstall the removed vehicle parts in the reverse order of removal 6 of 6
Download Pdf Manuals
Related Search
Related Contents
Original Bedienungsanleitung FUXTEC FX PDF を表示 T'nB PRCA35 User Manual - Nisuta.com Báscula Electrónica SX series - refrigeracion guevara.com.mx Samsung ML-2950ND User Manual Rosewill RNX-N180UB Chef'sChoice 688 Use and Care Manual GUIDE DE DEPANNAGE D`ACCORDEONS General Ledger User Manual Copyright © All rights reserved.
Failed to retrieve file