2014 touring led electra-glo saddlebag light kit - Harley
Contents
1. a X 2 r a a K 7 i A ag YY AL fe E lt a ET g 8 Na 5 g S ri DV EEE INO a TY dl D JEN DA L T I O To left E Glo To right E Glo Harness 69200713 WORM rai ON Harness 69200722 separate purchase Figure 3 Install Electrical Connection Harness 4 Get harness 69200713 from the kit Plug the harness into the connector on 69200722 If the connector on 69200722 is consumed by other accessories purchase adapter har ness 70264 94 5 Route one leg of the harness toward the right saddlebag and route the other leg toward the left saddlebag 6 Open the right saddlebag and release the saddlebag from the vehicle by removing the 1 4 turn fasteners Rock the saddlebag outward to gain access to the E Glo Light Rail connector on the bag 7 Plug the harness connector into the connector on the saddlebag 8 Return the saddlebag to its normal position using the 1 4 turn fasteners removed above 9 Repeat for the opposite side 10 Secure the harness to existing wiring or frame members using the cable ties provided in the kit 2of3 COMPLETION 1 See the service manual Replace the main fuse one Aree W l l After installing seat pull upward on seat to be sure it is e With the ignition in the OFF position Light Rail LEDs are locked in position While riding a loose seat can shift OFF causing loss of contro2. a Position the tape strips at a right angle to the long leg of the E Glo rails with the 3 inch 76 mm tack free zone stretched across the face of the light rail b Pull the tape tight while adhering the ends to the saddlebag 13 See Figure 2 Route the E Glo Light Rail wiring as shown Retain the wiring with the clips provided in the kit is07933 1 E Glo Light Rail wiring 2 Clips 2 Figure 2 Wire Routing 14 Repeat 1 13 for the left saddlebag 15 Allow the assemblies to dwell for 24 hours 16 Remove the reference marks 17 See the service manual Install the saddlebag lids 18 See the service manual Install the saddlebag to the vehicle PREPARATION AWARNING To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b J05709 NOTE e For vehicles equipped with security siren With security fob present turn ignition switch ON After system is dis armed turn ignition switch OFF IMMEDIATELY remove the main fuse per the service manual e For vehicles WITHOUT security siren See the service manual to remove the main fuse HARNESS ROUTING 1 See the service manual Remove the main fuse 2 See the service manual Remove the seat 3 See Figure 3 Install the Electrical Connection Harness Part No 69200722 purchased separately per the instructions in that kit if not already present is07932
3. equal parts of isopropyl alcohol and distilled water Allow to dry completely 7 Prepare the following pieces of masking tape See Figure 1 Cut 2 12 inch 30 5cm and 2 3 inch 76mm strips of masking tape Apply the 3 inch 76mm strips to the center of the 12 inch 30 5cm strips adhesive to adhesive creating a tack free zone is07930a 1 3 inch 76mm tape adhesive side down 2 12 inch 30 5cm tape adhesive side up amp Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled Figure 1 Create tack free zone 1of3 Please dispose of materials responsibly 8 Remove the adhesive tape backing from the short leg and from the semicircular shape of the rail Do not remove the backing from long leg at this time 9 Position the light rail as in the test fit above Flex the short leg away from the saddlebag while lowering the assembly down into position 10 Once seated and with the help of an assistant hold the front of the E Glo rail firmly in position while flexing the long leg away from the saddlebag at the rear Remove the adhesive backing from the rail Verify alignment with the reference marks and allow the long leg to fully contact the saddlebag 11 Apply firm sliding pressure in all tape areas Do not use extreme pressure over the lens 12 Temporarily clamp the rail in place using the masking tape as follows
4. cMOTOR HARLEY DAVIDSON WY J05709 INSTRUCTIONS REV 2014 02 06 2014 TOURING LED ELECTRA GLO SADDLEBAG LIGHT KIT GENERAL Kit Numbers 68000082 68000083 Models For model fitment information see the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only Installation Requirements This kit requires the installation of an Electrical Connection Harness Part No 69200722 unless one has already been installed Service Manual Required WARNING The rider s safety depends upon the correct installation of this kit If the procedure is not within your capabilities or you do not have the correct tools have a Harley Dav idson dealer perform the installation Improper installation of this kit could result in death or serious injury 00308a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is available from a Harley Davidson dealer Electrical Overload NOTICE It is possible to overload your vehicle s charging system by adding too many electrical accessories If the combined electrical accessories operating at any one time consume more electrical current than the vehicle s charging system can produce the electrical consumption can discharge the battery and cause damage to the vehicle s electrical system See an authorized Harley Davidson dealer for advice about the amount of current consumed by ad
5. di tional electrical accessories or for necessary wiring changes 00211c AWARNING When installing any electrical accessory be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modi fied Exceeding the maximum amperage can lead to elec trical failures which could result in death or serious injury 00310a J05709 This 2014 Touring LED Electra Glo Saddlebag Light Kit requires up to 720 mA additional current from the electrical system Kit Contents See Figure 4 and Table 1 INSTALLATION 1 See the service manual Remove the right saddlebag from the vehicle 2 See the service manual Remove the saddlebag lid 3 Position the saddlebag upside down on a protected surface with the latch loops overhanging the edge 4 With the adhesive backing still in place test fit the right E Glo light rail a Align the semicircular shape of the rail with the corres ponding shape at the front of the saddlebag b Verify that the rail flange makes contact all along the saddlebag base and consistently follows the saddlebag along the entire length of the long leg c With the help of an assistant hold the rail in place and trace reference marks on the saddlebag with a contrasting colored grease pencil 5 Lift the light rail from its test fit location 6 Clean the saddlebag in the areas corresponding to the tape installed on the E Glo Rails with a mixture of
6. l which could result in death or With the ignition in the ON position Light Rail LEDs are Serious injury 00070b ON 2 See the service manual Install the seat ee the ignition in the ACC position Light Rail LEDs are SERVICE PARTS is07934 Figure 4 Service Parts Electra Glo Saddlebag Light Kit Table 1 Service Parts Table Item Description Quantity Part Number Cable strap 4 10006 2 Clip 4 10102 3 Wiring harness saddlebag E Glo light Not Sold Separately 4 Electra Glo light rail right Not Sold Separately 5 Electra Glo light rail left Not Sold Separately J05709 3of3
Download Pdf Manuals
Related Search