tci® 861710 burnout kit
Contents
1. Figure 2 888 776 9824 10 2010SM2. tape can cause contamination of brake system You must obtain a pair of brake line fittings to join the brake line to the solenoid The brake line fittings will seal the system and keep from leaking fluid pressure Step 3 Mount solenoid securely Step 4 Next connect brake lines The opening that is marked Master must be connected to the proportional valve and the opening that is marked Brake must be connected to the front wheel cylinder Use only DOT grade or better brake lines Step 5 Bleed brake system After the brake lines are installed the system must be air bled to release any air trapped in the system Consult service manual for your vehicle for special procedures Refill master cylinder to proper level using approved DOT brake fluid Step 6 Wiring the solenoid LED s and LED Module The solenoid has two 2 wires one 1 ground wire and one 1 hot wire Proper installation is required Make sure that the ground wire black is connected to a good clean contact area When connecting wires use barrel connectors or other electrical connectors If additional wire is required use only the same gauge or larger Step 7 Refer to Figure 1 for correct wiring of the Switch LED s LED Module and fuse Step 8 Mounting micro switch The bracket provided can be easily mounted in a variety of locations The switch must be mounting for easy operation We suggest mounting close to the steering wheel or on the shifter Aft
3. 151 INDUSTRIAL DRIVE ASHLAND MISSISSIPPI 38603 httpz www tciauto com TELEPHONE 662 224 8972 FAX LINE 662 224 8255 E MAIL tech tciauto com TCI 861710 BURNOUT KIT This TCI Kit Contains Qty Description Qty Description 1 Burnout Solenoid 1 Burnout Module 2 Mounting Screws 2 LED Lights 1 Micro Switch 6 ft Red Wire 1 Wire Connector Kit ft Black Wire 2 Mounting Brackets 25 ft Black Wire 1 Fuse Holder 2 LED mount screws amp washers ATTENTION Disconnect Battery before beginning Step 1 Select a mounting location that will position the solenoid between the proportional valve and the front wheel cylinder Can be installed for rear system if required Just connect to rear brake system Kit contains two 2 1 4 x1 3 4 self tapping screws Use 3 8 socket to mount solenoid in place Step 2 Before mounting solenoid note that the solenoid has two 2 openings The brake lines are connected to these openings There are two 2 common size brake lines available TCI s solenoid will work with either size But you will need to purchase the proper bushing adapter The thread size in the TCI solenoid is 1 8 straight pipe thread Purchase either an adapter that goes from 1 8 to 1 4 inverted flair or 1 8 to 3 16 inverted flair When using the bushing adapters you may use TEFLON tape on the adapter threads but do not cover the first two 2 threads Use of an excessive amount of TEFLON sealing
4. er you have selected where the switch will be mounted measure length of wire needed to make the connection Make sure that the terminals of the micro switch are connected to the wires properly Mount the Burnout module under the dash then using the included mounting brackets and the 10X24 screws and washers mount the LED to the bracket as shown in Figure 2 Mount brackets to wheel wells or in an inconspicuous place out of the way but where it points toward the back of the rear tires and or vehicle Secure all loose wires to avoid contact with any moving object Step 9 Test system Reconnect battery Jack vehicle up until the wheels are off the floor Using proper weight jack stands secure the vehicle on the stands Turn ignition on Next have someone turn the electrical system on push on the brake pedal press the micro switch button down and hold then release the brake pedal If wired properly this will engage the front wheel cylinder and keep the front wheels from turning and cause the LED s to function Next try to turn the front tires When the micro switch is depressed you should not be able to turn the tires Only when the micro switch button is release will you be able to turn the tires over Figure 1 Switched 12V FUSE sh ao SW PUSHBUTTON BURNOUT 7 SOLENOID y o m L iHa il aroun BURNOUT LED MODULE
Download Pdf Manuals
Related Search