"service manual"
Contents
1. 12 N ALUL JL Mig Al 2 To remove the lid cover start with unlocking the 4 snap locks B see picture 4 To remove the side panels unlock the 2 snap locks at each side and gently pull of the panels 5 Once the front and side panels are removed the inner components can be reached 2 9 DISASSEMBLY AND RE ASSEMBLY ADVISE 3 The lid cover is still fixed with two snap locks C which can be reached with a screwdriver from the backside of the appliance see pictures 4 Once the lid cover has been removed the inner parts can be reached 5 To reassembly please follow steps backward HD7860 10 REPAIR INSTRUCTION Descaling Descaling is an important element in Senseo maintenance It should be done at least once every 3 months up to 6 times a Year This will prolong the life of your appliance and will guarantee optimal brewing results for a long time Use the correct descaling agent Only citric acid based descalers are suitable for descaling the SENSEO machine This type of descaler descales the appliance without damaging it2. For the correct amount see under Descaling procedure below Each descaling mixture can be used only once After use the descaling mixture is no longer active We advise you to use the special SENSEO Descaler HD7006 Read the instructions on the package of the descaling agent Never use a descaling agent based on mineral acids such as sulphuric acid hydrochloric acid sulphamic acid and acetic acid e g vinegar These descaling agents may damage your SENSEO coffee machine e Follow the steps in the section headed Descale the appliance see DFU Direction for Use manual 3 9 REPAIR INSTRUCTION Volume adjustment The PCB circuit board makes it possible to adjust the volume output by means of pushing the one cup and two cup user controls How to adjust the volume output 1 Be sure the boiler is filled properly other wise perform fill procedure see DFU for instructions 2 Switch appliance on and wait until the unit is ready to brew 3 Be sure a pod holder is placed but without a Coffee POD Only adjusting with plain water 4 Place a cup on the drip tray cover and push the one cup button 5 When the appliance has finished it is stabilized to perform the volume adjustment 6 Empty the cup podholder and push again for one cup setting measure the volume output with a graduated beaker In the table you can find the requirements for the minimum maximum volume output cc mL values depending fr
3. and has to plug the appliance on the mains When the Senseo main switch has been pushed the main switch LED will light continuously This is only the case when the Senseo has not finished the filling procedure completely First use When the consumer pushes the one or two cup button the Senseo will start automatically the pump to fill the boiler When the boiler is filled the pump stops pumping Pump time approximately 22 seconds When the filling procedure has been successful the software will clear a Boiler_empty_flag in the Eeprom By means of this Boiler_empty_flag the system knows the boiler is filled or not When the Senseo is switched off or disconnected from the mains the value of the Boiler_empty_flag is stored in the Eeprom chip Restoring the Boiler_empty_flag to production default Some times it is needed that the boiler of the Senseo have to be emptied This for instance in wintertime were the possibility exists that the boiler becomes frozen during transport e g For those occasions it is handy to restore the Boiler_empty_ flag again to production default Bringing the Senseo back into production status has the benefit the flush routine will be activated automatically when installed by the consumer see topic Automatic filling procedure To SET the Boiler_empty_flag can be done by Keep the 1 cup button pressed while plugging in the power cord of the appliance The main switch LED will blink very rapidly for a
4. 0047409 Epcos 470 nF X2 capacitor 31 4222 247 61601 Housing brew chamber detection sensor 32 422225951201 Water container housing panel assy Vapor Grey 5 9 HD7860 10 EXPLODED VIEW 6 9 HD7860 10 EXPLODED VIEW A Always exchange the whole lid button assy 6 g the Never unscrew the screws D which are holdin button case assy When you do so the button case will not be air tight anymore which can result in steam water leakage This will cause that the button assy PCB will malfunction after some use 7 9 HD7860 10 FE 4 EL LM EXPLODED VIEW HD7860 10 EXPLODED VIEW
5. Coffee Maker Senseo Service Service z ME i lb gt D Philips Consumer Lifestyle ervice Manual PRODUCT INFORMATION Brewhead detection sensor Water level Temp After the product has been repaired it should function sensor S1 properly and has to meet the safety requirements as officially laid down at this moment This product meets the requirements regarding interference suppression on radio and TV TECHNICAL INFORMATION Voltage 220 240 V Frequency 50 60 Hz AE s Power consumption 1450W Standby power lt IW Contents reservoir 1200 cc R Colour setting Bright style Sap coding HD7860 10 OPTIONAL accessories Push buttons No specific issues Published by Philips Consumer Lifestyle Printed in the Netherlands Copyright reserved Subject to modification m PHILIPS DISASSEMBLY AND RE ASSEMBLY ADVISE HD7860 10 To be able to open the appliance please follow bellows steps To be able to reach the inner parts of the lid assy follow 1 Make sure all accessories like tank podholders drip tray below steps spout and collector are removed 1 Remove the two screws A which are holding the lid Remove the two screws at the backside of the appliance see picture Place the appliance on it s back and remove the front panel by unlocking the two snap locks see picture X
6. om the country version One cup setting Including Pod holder water spec Without Coffee pod Unplug the appliance from the mains 8 Press the 1 and 2 cup button simultaneously and plug the mains on 9 When above step succeeded the led will turn on continuously 10 Depending if the volume has to de or increase you have to push the one or two cup button Every time you push the 1 or 2 cup button the LED will turn off for 0 5 second feedback to user and the pump time will be shortened or lengthened for 0 5 seconds depending which button was pushed Pushing 1 cup button pump time will be shorten with 0 5 sec is approximately 3 5 cc mL less coffee Pushing 2 cup button pump time will be lengthen with 0 5 sec is approximately 3 5 cc mL more coffee When the volume has to increase with 10 cc for example push the 2 cup button 3 times The new value will be stored when you switch the appliance off by pushing the main switch LED will turn off 11 Turn appliance on again and brew one cup measure the volume In case the volume is not within specification repeat steps 6 11 12 End HD 7860 10 Automatic filling procedure The Senseo PCB contains a automatic filling procedure software routine This fill routine is only meant for back up Normally the consumer has to follow the guidelines stated in the DFU The flling procedure functions as follows The consumer has to fill the water container
7. pproximately 1 second To check if the Boiler_empty_flag is really set you should reconnect the power cord a second time to the net and push the main switch The main switch LED should light continuously 4 9 PARTSLIST E changed HD7860 10 Pos Service code Description l 4222 259 41540 Padholder assy 1 cup Dark Grey 24222 259 4530 Padholder assy 2 cup Dark Grey 3 4222 240 00460 Driptray cover 4 4222 247 61550 Driptray Vapor Grey 5 4222 259 43280 Water container assy Translucent Dark Purple 6 4222 259 45320 Lid Button assy Vapor Grey 7 4222 240 01410 Slider spring 8 4222 240 05990 Ejector pin 9 4222 247 06810 Brew chamber seal 10 4222 247 41920 Distribution disk 11 4222 259 43430 PCB hall sensor lid close 12 4222 247 61270 Spout Deep Black 13 4222 247 61290 Spout cover Vapor Grey 14 4222 247 61590 Decorative spout cover 15 4222 247 61420 Left panel Vapor Grey 16 4222 247 61470 Front panel Vapor Grey 17 4222 247 61280 Collector Deep Black 18 4222 247 61430 Right panel Vapor Grey 19 4213 247 05250 Foot 20 422224761940 TCO cap 21 4222 247 43690 Boiler pin cover 22 4222 259 44270 Boiler assy TCO V7 0 230 V 23 4222 259 43310 Valve assy HD7860 24 4222 259 43420 PCB hall sensor water container 25 4222 247 05130 NTC O ring 26 4222 259 35500 NTC assy 27 4222 259 37240 Pump ULKA HF 230 V 50 Hz 28 4222 259 43330 PCB assy main 29 4222247 61310 Push rod 9965 1
Download Pdf Manuals
Related Search