GENUINE PARTS INSTALLATION INSTRUCTIONS CAUTION
Contents
1. 4 Turn ignition swtich to ON position 5 Record the customer radio presets and other presents as required 6 Put shift lever in P position for A T and CVT or ist for M T 7 Turn ignition switch to OFF position 8 Use seat and floor protection Page 2 of 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE A CAUTION e Allow 3 min after key off and doors closed for vehicle to time out if doors are opened again additional time may be required Allow an additional 3 min after negative terminal disconnect before seperating any electrical connectors 9 Using a 10mm socket and ratchet disconnect the negative battery terminal Fig 1 A CAUTION e Do not use excessive force when removing OE mirror from windshield The window button may seperate from windshield or the windshield could break 10 Remove the OE rearview mirror Fig 2 a Slide flat end of 3mm screwdriver into opening at bottom of mirror mount until resistance is felt b Apply additional upward force and twist 90 degrees to lift lock spring c Lift mirror upward off mirror mount while applying pressure with screwdriver Locking Tab NI lt Mirror Mount N Windshield Button Tool 11 Discard mirror 12 Using a panel removal tool loosen the driver side weather strip and remove from the top of the A pillar to the insturment panel Fig 4 Page 3 of 19 999L1 C3000II Rev 9 22 142. making sure to preserve staircase shape b After tapping second accessory form a strain relief loop for the tapped wire on the non pierce side as shown in Fig c and detailed in step 5b NOTE Do not secure before reading step 30 Repeat as necessary Page 9 of 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE 32 Securing multiple posi taps on the same circuit Fig 25 a Secure the pierced and tapped wires from the first posi tap along with the tapped wire from the non pierce side of the 2nd posi tap to the body of the 2nd tap with electrical tape 2 revolutions b Secure the tapped wires from the non pierced sides of each tap to each other with electrical tape 2 revolutions at a distance of 6 35mm 0 25in from the head of last posi tap shown in Fig b Note No single wire should be posi tapped more than 4 times to maintain integrity Repeat as necessary 33 Multiple accessory taps on the same circuit secured Fig 26 a The first accessory is tapped relieved and has the pierced wire on the heat shrink side and the tapped wire on the non pierce side secured to the first tap as shown in Fig a b The second accessory is tapped relieved and has the pierced wire the tapped wire on the non pierce Side and the tapped wire from the non pierce side of the first posi tap secured to the second tap as shown in Fig b c Finally the tapped wires on the non pierce side of the first and subsequent posi
3. Ref Quick Reference Card Page 17 of 19 999L1 C30001I Rev 9 22 14 DIAGNOSTIC FLOW CHART YES Orderservice part 999L1 VZ000 remove existing EC mirror and replace with new YES Press powerbutton HOMELINK TROUBLE SHOOTING GUIDE Part Number 999L1 V3000 Before attempting to trouble shoot EC mirror HomeLink function ensure the following 1 Mirror is manufactured by Gentex Corporation the letters GNTX will be etched onto the back of the mirror and the compass display window will be in the mirror glass 2 EC mirror harness must be fully plugged into EC mirror 3 Vehicle ianition must be in the ON position Press each ny button Is green LED illuminated Customermustnow attempt to program HomeLink This usually cannot be completed atthe Dealership because many remote controlled devices utilize rolling code Each HomeLink button illuminates red LED when pressed Red LED illuminates on EC mirror Is green LED illuminated Did customer successfully program HomeLink Order service part 999L1 VZ000 remove existing q EC mirror and replace with new Mirror receiving 12V 12V being delivered to EC mirror Did customer 1 Attempt to follow programming instructions User Guide in vehicle glovebox 2 Visitwww HomeLink com 3 Contact HomeLink Customer Service hotline
4. 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE i Straight and evenly spaced all the way around ii Tighten and minimize gap wire jacket should be crushed OT Insert wire to here f Tighten i Straight and evenly spaced all around ii Tight and no gap and test the signal Page 8 of 19 25 Tap accessory service wire Fig 18 a Identify and confirm correct wire in the Accessory Service Connector to be tapped b Remove cap slot side from tap body c Slide cap around single accessory wire d Position cap 6 35mm 0 25in away from the heat shrink end of the Accessory Service Connector measurement for first posi tap installed on the circuit e Tighten the tap TIGHT with finger pressure f Tighten by another quarter turn NOTE Figures are not to scale 26 Inspect the tap to ensure correct installation Fig 19 a Pull on wire lightly to ensure connection b Inspect the tap to ensure correct installation c Test signal to ensure that it is working Avoid putting pressure on the vehicle wire and tap for the remainder of the installation 27 Tap accessory wire Fig 20 a Remove tap non pierce side from tap b Remove the protective stub from the wire c Insert wire through the non pierce side d Spread the individual strands into fan shape e Insert wire into the tap body and ensure that it is all the way in f Tighten the tap TIGHT with finger pressure g Tighten by another quar
5. MIRROR Legend Posi tap I Page 19 of 19 999L1 C3000II Rev 9 22 14
6. exist ing vehicle harness with 6 wire ties At the base of the A pillar tuck the mirror harness behind the vehicle harness and route through the top side of the square Shaped opening located below the vehicle conncetors Fig 14 22 Wrap 3 pieces of foam tape around the mirror harness and using fish tape feed the harness from the upper dash behind the fuse box and through to the lower driver side kick panel area Secure the EC mirror har ness to the body harness in the driver side kick panel Wire Tie area with 1 wire tie Fig 15 Foam Tape ee eu e Accessory Service Connector 23 Routing the harness a Locate the driver side Accessory Service Connector up under the dash along the left side of the fuse block on the driver side of the vehicle Fig 16 Note A previously installed accessory connector may be present If so carefully remove the accessory connector harness from the plug before posi tapping It is recommended that all posi tapping be completed before reattaching the accessory connector to the plug Page 6 of 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE CAUTION This Accessory Service Connector is for use only with Genuine Nissan or Infiniti or Nissan or Infiniti ap proved accessories Use of this connector with non Genuine Nissan or Infiniti or Nissan or Infiniti approved accessories or failure to follow the installati
7. 1 800 355 3515 ENSURE 1 EC harness power wire is securely plugged into wire splice Posi tap connectoron vehicle 12V wire ENSURE 2 EC harness ground wire is securely attached 1 EC harness power wire to vehicle gounding point is securely plugged into blue wire of junction block connector 2 Check fuse corresponding to connection point of junction block to see if it needs to be replaced 3 EC harness ground wire is securely attached to vehicle grounding point Customer must at a minimum contact the HomeLink Customer Service hotline for help with programming before returning EC mirror as defective Mirror receiving 12V 12V being delivered to EC mirror NO Mirror is functioning Order service part 999L1 V3002 remove existing EC mirror wiring and replace with new HomeLink and the HomeLink house are registered trademarks of Gentex Corporation Page 18 of 19 999L1 C3000II Rev 9 22 14 DIAGNOSTIC FLOW CHART EC MIRROR KIT DRIVER SIDE ACCY_SER_CONN CONNECTOR JJ m 0 BAT TAIL_LAMP ROOM_LAMP BAT_SAVER FR_DOOR_SW_RH FR_DOOR_SW_LH THRU_SIGNAL_1 RR_DOOR_RH RR_DOOR_LH LT_GRN BLU LT_BLU Nj gt l jeje jaja js jojn zz G lt TH12FW NH BLK W BLU DOT Copper Cond BLK W WHT TRACE Copper Cond BLK Silver Cond SS if2 s 4 s 6 7 48 9 10 41 12 Note Pin location is referenced looking into wire side of connector l EC
8. GENUINE PARTS INSTALLATION INSTRUCTIONS aa a rarer nr APPLICATION Murano PART NUMBER 999L1 V3000 KIT CONTENTS Qty Part Description Service Part Number 1 EC Compass HomeLink Mirror 999L1 VZ000 Qty pt Harness Assembly Ignition Battery and Ground 9 EE Posi tap Wire Tie Foam Tape Tether Clip A Pillar 76988 5AA1A 1 4 Manual Installation Instruction Download 999V2 AWO000 User Guide TOOLS REQUIRED 3mm Flat Screwdriver Side Cutters Ratchet Nylon Trim Removal Tool 1 Phillips Screwdriver Fish Tape Clean Rag T20 Torx Bit Screwdriver Fish Wire 10mm Socket PRE INSTALLATION WARNINGS CAUTIONS CRITICAL STEPS and NOTES e Dealer Installation Recommended Instructions may refer to Service Manual e For HomeLink Troubleshooting refer to page 18 or call 1 800 355 3515 for assistance A CAUTION e This is a universal kit so all parts may not be used e Place removed vehicle trim components in a clean dry area to prevent damage HOMELINK AND THE HOMELINK HOUSE ARE REGISTERED TRADEMARKS OF GENTEX CORPORATION Page 1 of 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE A CAUTION e Always confirm the ignition is in OFF position before changing switch condition 1 Apply parking brake 2 Confirm vehicle is no longer in default shipping state or inventory position as shown below Failure to confirm vehicle has been removed f
9. INSTALLATION PROCEDURE A CAUTION e Exercise caution when removing and installing LH front pillar garnish due to side airbag placement Reference Figure 5 below for further detail e Do NOT re use LH front pillar garnish clip LH front pillar garnish clip P N 76988 5AA1A MUST be replaced dur ing re installation of garnish A Pillar Garnish A Pillar Garnish 13 Disengage driver side front pillar garnish fixing clip with a panel removal tool cut the clip with a cutter and then remove front pillar garnish Fig 6 a Remove and discard the clips from the vehicle b If equipped disconnect wire leading to tweeter 14 Remove the door sill plate and kick panel from the driver side of the vehicle a Pull up sill plate to disengage the pawls Fig 7 b Remove the sill plate from the body panel c Remove kick panel fixing clips with a panel removal tool and then remove the kick panel Fig 6 15 Install rearview mirror a Plug the harness connector into the back of the mirror pressing firmly until a click is heard Pull GENTLY on the harness to confirm the har ness is seated completely b Slide the rearview mirror base over the button on the windshield c Using a T 20 Torx head driver tighten the screw on the mirror mount 1 5 2 0 Nm 1 3 ft Ibs Page 4 of 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE 16 Rotate visor clip counterclockwise and remove a Wrap 1 piece of foam t
10. ON Ensure vehicle is in well lit area Check to see that the green LED is illuminated If it is not press the button to turn it on Cover the forward looking photocell located to the driver side of the wire harness connection on the back of the mirror with a dark cloth or towel After a few seconds the mirror should begin to darken Timing will vary with ambient light levels and a flashlight may be shined on the rearward photocell if needed to accelerate effect Fig 36 OOOO OLI HomeLink Buttons Compass Window Rearward Photocell Red LED _ Dark Cloth or Towel Remove the cover from the forward looking photocell and the mirror will begin to clear Push the N button to ensure compass display shows either a direction such as NE or a C and that it can be turned ON and OFF Testing is now complete Set Compass Zone With the display turned ON push the N button for 3 seconds until a number appears in dis play numbers correspond to regional compass zones Press and release N button to scroll through zone numbers Release N button when correct zone number is displayed Fig 38 Zone number will disappear and display will return to showing either a directional heading or a C after 5 seconds of no switch activity of OX hse Calibrate Compass Drive vehicle in circles 360 at 5 mph or less un
11. ape around the harness and using a panel removal tool tuck the harness between the headliner and roof above the EC mir ror Fig 9 Visor gd ie Foam Tape 17 Verify that a approximately 3 75mm of wire are between the bottom of the wire cover and connector on the back of the mirror Failure to allow the appropriate length will result in limited to no movement for the mir ror Fig 10 18 If a wire cover was removed from the OE mirror discard the OE wire cover and use the new wire cover from kit contents a Route harness into the groove of the wire cover and attach to the mirror mount b Slide the forks on top of the wire cover into the headliner cut out Fig 11 c Verify cover is properly seated and aligned to headliner cut out 19 Grasp the mirror and rotate downward Check to ensure wire cover sits flush against the windshield Fig 12 a If there is a gap between the wire cover and the windshield ensure there is enough harness slack from the mirror to the headliner Adjust if necessary 20 Wrap three additional pieces of foam tape around the mirror harness evenly spaced along the headliner as shown Fig 13 a Using a panel removal tool tuck the wire harness between the headliner and the roof Fig 13 Foam Tape Page 5 of 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE 21 Route the harness down the driver side A pillar and premeasure foam tape location Secure to the
12. o see if it needs to be replaced Orderservice part 999L1 VvZooo remove existing EC mirror and replace with new 3 EC harness ground wire is securely attached to vehicle gounding point YES 12V being delivered to EC mirror Order service part 999L1 V3002 remove existing EC mirror wiring and replace with new r 999L1 V3000 VITIVe a Jil SF e tne TOWHOWING 1 Mirror is manufactured by Gentex Corporation the letters GNTX will be etched onto the back of the mirror and the compass display window will be in the mirror glass 2 EC mirror harness must be fully plugged into EC mirror n Correct direction is displayed YES Mirror is functioning YES properly y PERFORM CALIBRATION PROCEDURE Compass display reads GN 1 Reference Quick Reference card in vehicle glove box or EC mirror installation manual Incorrect direction is displayed Correct direction is displayed YES YES NO Some headings not displayed Orderservice part 999L1 VZ000 remove existing EC mirror and replace with new Heading is locked inone direction Heading incorrecton long trips NOTE Compass re calibration may be neccessary due to 1 Changes in vehicle magnetics due to installation of luggage racks ski racks etc 2 Vehicle body vibration overtime 3 Driving vehicle in new compass zone
13. on instructions for the connector contained in this package may result in damage to the accessory and or your vehicle Nissan or Infiniti is not liable for loss or damage due to improper installation or the installation of non Genuine or non approved accessories Posi TapTM is protected by patent 5 228 875 5 695 369 5 868 589 6 692 313 Jap 2881414 Aus 708700 Tia 103534 Can 2204826 Mex 200626 Korea 477279 China Z197105562 9 amp others pending 999Q09 AY001 Label IGN W HITE BAT RED TL_LMP PURPLE RM LMP YELLOW BATSVR PINK RN LT GRN GREY BLUE LT BLUE ORANGE BLACK H THRU SIGNAL 1 RR_DR_RH RR_DR_LH j D gt O T1 T ZZ viS Pr O nj A T Pin 6 8 B 10 GND 24 Using a posi tap connect the BLACK WIRE W SILVER CONDUCTOR from the mirror harness to the BLACK wire on the accessory connector harness Using a posi tap connect the BLACK WIRE W WHITE TRACE amp COPPER CONDUCTOR from the mirror harness to the ORANGE wire on the accessory connector harness Using a posi tap connect the BLACK WIRE WITH THE BLUE DOT amp COPPER CONDUCTOR from the mirror harness to the RED wire on the accessory connector harness Fig 17 a Reference Page 19 for additional wiring details b See Step 23 37 for posi tap installation instructions Y Verify mirror has been wired properly Note Be sure NOT to posi tap through the shrink tubing HARNESS NOT INCLUDED IN KIT REFERENCE PART NUMBER 999Q9 AYOO1 Page 7 of
14. on switch to ON and confirm proper operation of Vehicle Systems If equipped verify all window and sunroof one touch operation and perform the reset procedure if necessary Refer to the vehicle service manual for more details Confirm proper audio function AM FM SAT CD and AUX Re program radio presets and other vehicle settings to the recorded settings Start engine and verify that there are no new Diagnostic Trouble Codes Turn ignition switch to OFF HOL Place the Owner Manual Quick Reference Guide and or other Manual in the glove box Page 15 of 19 999L1 C3000II Rev 9 22 14 DIAGNOSTIC FLOW CHART Before attempting to Ouble shoc mirror Auto Dimming function ensure the following 1 Mirror is manufactured by Gentex Corporation the letters GNTX will be etched onto the back of the mirror and the compass displav window will be in the mirror glass 2 EC mirror harness must be fully plugged into EC mirror 3 Vehicle ianition must be in the ON position VERIFY AUTO DIMMING IS green LED FUNCTION illuminated 1 Cover forward facing photo cell with dark cloth ortape Shine light from flashlight shoplight etc atrearward facing photocell Press power button on EC mirror Does mirror Mirror is functioning darken properly Is green LED illuminated Order service part 12V being 999L1 VZOOO delivered to remove existing EC mirror and replace EC mir
15. r posi tap bundle foam strips Fig 31 a Wrap the posi tap bundle with foam tape following a pattern similar to the electrical tape making the best use of foam strips provided Fig 32 o l 39 Finished foam wrap for bundle strips top view Fig 32 a Make sure the finished wrap looks similar to Fig 32 Page 12 of 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE EC Mirror 40 Route the Accessory Service Connector up under the dash to the accessory connector plug and plug the con Harness Ns DERN nectors together Fig 33 om A E g Note Be sure the new harness routing does NOT le Connector interfere with the emergency brake in any way 41 Wrap the connectors with 1 piece of foam tape and secure the harness to the corrugated tubing running through the opening to the door with 1 wire tie Fig 34 42 Route any extra wire along the existing harness and bundle the EC mirror harness to the main body harness with a wire tie Fig 35 Page 13 of 19 999L1 C3000II Rev 9 22 14 ACCESSORY CHECK Note If errors are encountered during testing and compass calibration see diagnostic flow charts pages 16 18 Testing Tighten negative battery terminal nut to 5 4 Nm 47 8 in Ib With ignition switch OFF push each HomeLink button one at a time and verify that the LED indica tor to the left of the center switch illuminates with a red LED Fig 37 Turn the ignition switch to
16. rom this state will result in loss of normal vehicle operation The confirmation requires two checks 3 Locate Extended Storage Switch in cabin fuse block Confirm it is in the Customer position See below for reference a To remove transit mode Fuse Block b To remove transit mode BCM 1 Remove fuse cover lid 1 Confirm ignition switch is in OFF position 2 Push down shorting pin 2 Simultaneously push signal and wiper switch 3 Ign On 2 times without switch fully down for two 2 seconds starting the vehicle Note While in BCM Transit Mode turn signal indicators will remain illuminated for one Customer Inventory SIGUE PUSH DOWN PULL UP INCORRECT CORREC c To return to transit mode for storage 1 Ign Off JA 2 Remove the fuse cover lid j 3 Pull up shorting pin wW A N gt 4 Assemble fuse cover lid F 5 Ign On 2 time without turning vehicle on 6 Confirm transit mode condition on meter CUSTOMER DOWN INVENTORY UP Note Typical vehicle condition shown above Idenfity switch by permanent push pull fuse holder Actual position on fuse block may vary vehicle to vehicle Vehilce delivered to customer Customer Delivery Note The Storage Switch is an aid to improve battery life during vehicle storage at the dealer If the Extended Storage Switch fuse ever needs service after vehicle delivery discard Extended Storage Switch and install correct fush in its place
17. ror with new YES NOTE Auto dimming mirror malfunctions may occurdue to 1 EC harness power wire is securely plugged into 1 Obstructions blocking either the forward facing orrearward facing photo cells blue wire of junction block oo connector 2 Non factory tinting of windows ENSURE Orderservice part 999L1 VZOOOO remove existing EC mirror and replace with new 2 Check fuse corresponding to connection point of junction block to see if it needs to be replaced 3 EC harness ground wire is securely attached to vehicle gounding point YES 12V being delivered to EC mirror NO Orderservice part 999L1 V3002 remove existing EC mirror wiring and replace with new Page 16 of 19 999L1 C3000II Rev 9 22 14 DIAGNOSTIC FLOW CHART COMPASS TROUBLE SHOOTING GUIDE Part Numbe 3 Vehicle ignition must be in the ON positio Any displ Is greenLED VES ae ae illuminated window NO NO Press power button on EC mirror Press compass displa button on EC mirror Is green LED NES illuminated Any display in compass window NO YES 12V being delivered to EC mirror Order service part 999L1 VZ000 remove existing EC mirror and replace NO with new ENSURE 1 EC harness power wire is securely plugged into blue wire of junction block connector 2 Check fuse corresponding to connection point of junction block t
18. taps are secured to each other as shown in Fig c 34 Multiple accessory taps on different circuits secured Service together Fig 27 Connector a The tapped accessories with wires already secured Harness to tap bodies are stacked slightly staggered on top 6 35mm of each other as shown in Fig a b The tapped wires on the non pierce side of all the posi taps are secured to each other with electrical tape 2 revolutions at a distance of gt 6 35mm 0 25in as shown in Fig b c The pierced wires of the first and subsequent posi taps are secured to each other with electrical tape 2 revolutions at a distance of 6 35mm 0 25in as shown in Fig c Page 10 of 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE 35 Prep for foam wrap Fig 28 a Make sure the accessory taps have been wrapped appropriately as detailed previously and as shown in Fig 28 Service Connector Harness 36 Pre foam protective wrap Fig 29 a Starting at the heat shrink firmly wrap the posi tap bundle with electircal tape or non adhesive wire harness tape making sure to overlap the previous revolution Note If using non adhesive tape secure at the of wrap with electrical tape 2 2 revolutions Tea Nand NX SO Page 11 of 19 999L1 C3000II Rev 9 22 14 INSTALLATION PROCEDURE 37 Finished protective wrap Fig 30 a Make sure the finished wrap looks similar to Fig 30 A ment 38 Foam wrap fo
19. ter turn 28 Confirm the tapped accessory wire Fig 21 a Pull on the wire lightly to ensure connection b Inspect the tap to ensure correct installation c Test the signal to ensure it is working 999L1 C3000II_ Rev 9 22 14 INSTALLATION PROCEDURE 29 Forming strain relief loop always required Fig 22 a Gently bend the end of the pierced wire where it exits the cap down toward the body of the posi tap b On the tapped wire of the non piecrce side Starting at point b1 measure 50 8mm 2in to point b3 Make the first bend of the loop b2 half the distance measured 25 4mm 1in and up toward the body of the posi tap make the second bend of the loop b3 c Secure the pierced wire on the heat shrink side b3 n and the tapped wire on the non pierce side to the body of the tap with electrical tape 22 Revolutions NOTE If securing multiple taps to single circuit continue to Step 28 if tapping different circuits repeat steps 23 27 as required then proceed to step 32 30 Multiple posi taps on the same wire first tap Fig 23 a The first accessory is tapped relieved and secured as shown in Fig 17 thru 21 these steps are always the same b Measure 25 4mm 1in from point b to point c on the pierced wire c At points b amp c bend the pierced wire gently to Accessory form the staircase shape Harness 31 Multiple posi taps second accessory Fig 24 a Tap second accessory at point b
20. til compass display window shows a direction Check all Critical Installation Steps Check all torque values Auto Dimming mirror pg 4 step 13 fig 8 Page 14 of 19 999L1 C3000II Rev 9 22 14 ACCESSORY CHECK Verify all wiring is secure and not exposed Trim all excess cable ties flush Check all vehicle electrical systems that the accessory interfaces with Power mirror switch Traction control switch Hood Release Fuel Door Release RE INSTALLATION OF REMOVED PARTS A CAUTION Use caution when re installing interior components to avoid damage scratches or breaking of mounting clips Refer to the vehicle service manual for more information LH front pillar garnish Insert 1 new clip P N 76988 1AFOA into garnish hole ensuring long hook faces down Fig 39a Fig 39b Long Hook Faces Down Insert base of finisher Insert panel removal tool between front pillar garnish bottom side and body side and press clips into body Push garnish toward vehicle body to attach FINAL INSPECTION Verify re installed trim parts for proper flush fit no gap no waviness etc Verify all clips are fully engaged and locked Verify re installed trim parts are free from cracks scratches or stress cracks Verify vehicle headliner seat steering wheel center console floor carpets etc are not soiled Verify interior and exterior is not damaged AIWUUIUU Turn igniti
Download Pdf Manuals
Related Search