INSTALLATION INSTRUCTIONS
Contents
1. long bolt that holds the turn signal and support from inside the fender to the strut You may need to jack up the rear of the bike to be able to clear the tire DENTINE Securely support the motorcycle so it cannot fall over 4 Install the new hollow stud though the 16 lock washer into the turn signal body Make sure that you are using the 9 16 24 fine threaded stud 5 Install provided chrome hole plug in second hole from the rear of the strut Install the provided rubber plug into the wire exit hole in the turn signal body 6 Install turn signal with new stud through rear hole in Saddlebag Support and the strut using a new lock nut provided and original flat washer 7 Install provided 21 4 button head screw through front Support hole strut and into the fender 8 Locate turn signal wire inside fender and gently pull this wire toward the rear to get some additional wire to reconnect inside the turn signal body 9 Feed the wire out through the hollow stud and reconnect to the wire inside the turn signal body using the provided wire connector Wrap the connector with electrical tape and tuck connector into the space beside the bulb and socket 10 Reinstall the bulb and lens Tighten all nuts and bolts to OEM specifications FOR 02 05 FXD FXDC FXDL MODELS 1 Remove first fender support bolt behind shock absorber 2 Remove turn signal lens and bulb Cut the wire inside the turn signal body about 3 4 away fro2. DRAG SPECIALTIES SADDLEBAG SUPPORTS FOR 91 12 DYNA MODELS P N 3501 0258 the wire inside the turn signal body using the provided wire connector Wrap the connector with electrical tape and tuck the connector into the space beside the bulb socket 16 Reinstall the bulb and lens Tighten all nuts and bolts to OEM specifications Torque shock absorber to 65 ft lb FOR 06 08 FXDWG MODELS NOTE On the 2006 08 FXDWG models the turn signals are not relocated Do not remove them These saddlebag supports will not work on 2010 2012 FXDWG models due to the side mounted license plate frame 1 Remove the forward fender support bolt behind shock absorber Remove rear fender support bolt ahead of the turn signal 2 Install one of the provided 13 4 button head bolts through the support and then into the forward fender support mounting hole Use of the incorrect length bolt may cause interference with the rear tire and could cause the tire to deflate when ridden possibly causing loss of control of the motorcycle 3 Install one of the provided 13 4 button head bolts along with the support through the rear hole of the strut into the fender 4 Tighten all nuts and bolts to OEM specifications FOR 08 12 FXDF MODELS NOTE On the 2008 12 FXDF models the turn signals are not relocated Do not remove them 1 Remove the forward fender support bolt behind shock absorber Remove rear fender support bolt ahead of the turn signal 2 Inst
3. inside the turn signal body about 3 4 away from where it enters the hollow stud Remove the complete turn signal from the strut and remove the original stud from the turn signal body Install the new hollow stud through the provided 16 lock washer into the turn signal body Make sure that you are using the 9 16 24 fine threaded stud Install turn signal with new stud through rear hole in Saddlebag Support and the strut using a new lock nut provided and the original flat washer Install provided 21 4 button head screw through front Support hole strut and into the fender Locate turn signal wire inside fender and gently pull this wire toward the rear to get some additional wire to reconnect inside the turn signal body Feed the wire out through the hollow stud and reconnect to the wire inside the turn signal body using the provided wire connector Wrap the connector with electrical tape and tuck connector into the space beside the bulb socket Reinstall the bulb and lens Tighten all nuts and bolts to OEM specifications FOR 93 01 FXD FXDL MODELS T 2 cialti Remove first fender support bolt behind shock absorber Remove turn signal lens and bulb Cut the wire inside the turn signal body about 3 4 away from where it exits the turn signal body 3501 Kennedy Rd PO Box 5222 Janesville WI 53547 5222 P N 3501 0258 Page 1 of 3 INSTALLATION INSTRUCTIONS 3 Remove the 31 2
4. the turn signal and support from inside the fender to the strut 5 Remove the shock and shock mounting stud following instructions in the appropriate OEM Service Manual 6 Remove the strut from the frame 7 Reroute turn signal wire to inside of fender CAUTION Check clearance from location of wiring inside fender to tire Reroute if any contact is possible 8 Loosely install strut to frame with the shock absorber stud Reinstall shock 9 Install the new hollow stud though the provided 3 16 lock washer into the turn signal body Make sure that you are using the 16 18 coarse threaded stud 10 Install provided chrome hole plug in the third hole from the rear of the strut 11 Install turn signal with new stud through rear hole in the Saddlebag Support and the second hole from the rear of the strut using a new lock nut provided and original washer Install provided 21 4 button head screw through front Support hole strut and into the fender Install one of the original bolts through the rear hole of the strut into the fender Locate turn signal wire inside fender and gently pull this wire toward the rear to get some additional wire to reconnect to the wire inside the turn signal body Feed the wire out through the hollow stud and reconnect to 12 13 14 15 3 3 FXDWG ONLY HOLLOW STUD Th 5 16 LOCK Ye WASHER TURN SIGNAL BODY A RUBBER PLUG f Specialties
5. REVISED 11 2011 INSTALLATION INSTRUCTIONS ATTENTION INSTALLER IF OTHER THAN OWNER Please forward this Instruction Sheet to the purchaser of this product These instructions contain valuable information necessary to the end user INTRODUCTION These instructions describe the procedure for properly installing the Drag Specialties Saddlebag supports for 1991 to 2012 Dyna models except for 2010 to 2012 FXDWG with side mounted license plate Review instructions carefully before beginning as they contain important information Please retain for future reference Particularly important information is distinguished in these instructions by the following notations NOTE A NOTE provides key information to make procedures easier or clearer CAUTION A CAUTION indicates special procedures that must be followed to avoid damage to the motorcycle and or accessories A WARNING indicates special procedures that must be followed to avoid injury to a motorcycle operator or person inspecting or repairing the motorcycle TOOLS REQUIRED 9 32 hex key 3 4 socket wrench 7 32 hex key 1 Phillips screwdriver 9 16 socket wrench Bike lift or equivalent 3 4 combination wrench PROCEDURE NOTE This saddlebag support bracket set includes eight 3 4 16 button head screws of varying lengths The correct length and number of screws to use is called out in the specific application for each model Please read the ins
6. all one of the provided 13 4 button head bolts through the support and then into the forward fender support mounting hole Use of the incorrect length bolt may cause interference with the rear tire and could cause the tire to deflate when ridden possibly causing loss of control of the motorcycle 3 Install one of the provided 13 4 button head bolts along with the support through the rear hole of the strut into the fender 4 Tighten all nuts and bolts to OEM specifications PROCEDURE FOR ALL MODELS CONTINUED 2 Reconnect battery cable 3 Test turn signals for proper operation 4 Reinstall seat and sissy bar if fitted Before operating motorcycle be sure all hardware is tight Check for proper clearance between all installed hardware and the rear tire throughout the travel of the suspension e FLAT WASHER o bs 3 3 LOCK NUT 91 92 FXD HOLE PLUG BUTTONHEAD i d BOLT ys F 91 01 FXD FXDWG SUPPORT 3501 Kennedy Rd PO Box 5222 Janesville WI 53547 5222 REVISED 11 2011 P N 3501 0258 Page 3 of 3
7. ed the wire out through the hollow stud and reconnect to the wire inside the turn signal body using provided wire connector Wrap the connector with electrical tape and tuck connector into the space beside the bulb socket 10 Reinstall the bulb and lens Tighten all nuts and bolts to OEM specifications FOR 93 01 FXDWG MODELS 1 Lift rear of motorcycle under the frame with a jack until the rear wheel is just off the ground Securely support the motorcycle so it cannot fall over 2 Remove first fender support bolt behind shock absorber Remove last fender support bolt behind turn signal 3 Remove turn signal lens and bulb Cut the wire inside the turn signal body about 3 4 away from where it exits the turn signal body 4 Remove the 31 2 long bolt that holds the turn signal and support from inside the fender to the strut 5 Remove the shock and shock mounting stud following instructions in the appropriate OEM Service Manual 6 Remove the strut from the frame 7 Reroute turn signal wire to inside of fender CAUTION Check clearance from location of wiring inside fender to tire Reroute if any contact is possible 8 Loosely install strut to frame with the shock absorber stud Reinstall shock 9 Install the new hollow stud through the provided 9 16 lock washer into the turn signal body Make sure that you are using the 16 24 fine threaded stud 10 Install provided chrome hole plug in the third hole from
8. lens and bulb Cut the wire inside the turn signal body about 3 4 away from where it exits the turn signal body f Specialties 3501 Kennedy Rd PO Box 5222 Janesville WI 53547 5222 P N 3501 0258 REVISED 11 2011 DRAG SPECIALTIES SADDLEBAG SUPPORTS FOR 91 12 DYNA MODELS P N 3501 0258 3 Remove the 31 2 long bolt that holds the turn signal and support from inside the fender to the strut You may need to jack up the rear of the bike to be able to clear the tire eNA Securely support the motorcycle so it cannot fall over 4 Install the new hollow stud through the provided 9 16 lockwasher into the turn signal body Make sure that you are using the 16 18 coarse threaded stud 5 Install provided chrome hole plug in second hole from the rear of the strut Install the provided rubber plug into the wire exit hole in the turn signal body 6 Install turn signal with new stud through rear hole in Saddlebag Support and the strut using a new lock nut provided and original flat washer 7 Install provided 2 button head screw through front Support hole strut and into the fender Use of incorrect length bolt may cause interference with the rear tire and could cause the tire to deflate when ridden possibly causing loss of control of the motorcycle 8 Locate turn signal wire inside fender and gently pull this wire toward the rear to get some additional wire to reconnect inside the turn signal body 9 Fe
9. m where it exits the turn signal body 3 Remove the 31 2 long bolt that holds the turn signal and support from inside the fender to the strut You may need to jack up the rear of the bike to be able to clear the tire DENTINE Securely support the motorcycle so it cannot fall over 4 Install the new hollow stud through the provided 16 lock washer into the turn signal body Make sure that you are using the 9 16 18 coarse threaded stud 5 Install provided chrome hole plug in second hole from the rear of the strut Install the provided rubber plug into the wire exit hole in the turn signal body 6 Install turn signal with new stud throughrear hole in Saddlebag Support and the strut using a new lock nut provided and original flat washer 7 Install provided 21 4 button head screw through front Support hole strut and into the fender 8 Locate the turn signal wire inside fender and gently pull this wire toward the rear to get some additional wire to reconnect inside the turn signal body 9 Feed the wire out through the hollow stud and reconnect to the wire inside the turn signal body using the provided wire connector Wrap the connector with electrical tape and tuck connector into the space beside the bulb socket 10 Reinstall the bulb and lens Tighten all nuts and bolts to OEM specifications FOR 06 12 FXD FXDC FXDB FXDL MODELS 1 Remove first fender support bolt behind shock absorber 2 Remove turn signal
10. the rear of the strut 11 Install turn signal with the new stud through rear hole in the Saddlebag Support and the second hole from the rear of the strut using a new lock nut provided and original washer 12 Install provided 21 4 button head screw through the front fender support hole strut and into the fender 13 Install one of the original bolts though the rear hole of the strut into the fender Page 2 of 3 INSTALLATION INSTRUCTIONS 14 Locate the turn signal wire inside fender and gently pull this wire toward the rear to get some additional wire to reconnect to the wire inside the turn signal body 15 Feed the wire out through the hollow stud and reconnect to the wire inside the turn signal body using the provided wire connector Wrap the connector with electrical tape and tuck connector into space behind the bulb socket 16 Reinstall the bulb and lens Tighten all nuts and bolts to OEM specifications Torque shock absorber stud to 65 ft Ib FOR 02 05 FXDWG MODELS 1 Lift rear of motorcycle under the frame with a jack until the rear wheel is just off the ground Securely support the motorcycle so it cannot fall over 2 Remove first fender support bolt behind shock absorber Remove last fender support bolt behind turn signal 3 Remove turn signal lens and bulb Cut the wire inside the turn signal body about 3 4 away from where it exits the turn signal body 4 Remove the 31 2 long bolt that holds
11. tructions closely This kit also contains four hollow turn signal mounting studs Depending on your model year you will use either the two 9 16 24 fine threaded or the two 16 18 coarse threaded hollow studs Compare the studs to the turn signals on your bike and use the studs that match the threads on your turn signal bodies NOTE 1999 and later Dyna models feature a wiring terminal block located within the taillight As another option to cutting the turn signal wiring on these models you may remove the taillight lens and unplug the turn signals from the terminal block The wires may then be pulled out from the under side of the fender and the terminal connectors removed Special tools may be required to remove the terminal connectors from the wiring ends If you do cut any wiring using solder and heat shrink tubing is preferred to the blue connectors included with the saddlebag support kit FOR ALL MODELS NOTE On all models install one side first and then repeat for the other side 1 Remove seat and sissy bar if fitted on all models D Spe DRAG SPECIALTIES SADDLEBAG SUPPORTS FOR 91 12 DYNA MODELS P N 3501 0258 Disconnect the negative battery cable to prevent short circuits before performing any of the following steps FOR 91 92 FXDB S FXDB D FXDC MODELS 1 4 5 7 9 Remove rear fender support bolt behind shock absorber 2 Remove turn signal lens and bulb Cut the wire
Download Pdf Manuals
Related Search