Home
Led Tail Lamp Instruction Sheet - Harley
Contents
1. 6 and crimp tails 7 facing up in the same direction as the button 3 on the top of the socket housing b Insert the terminal into the correct cavity 1 2 3 or 4 4 until it snaps into place with an audible click c Gently tug on wire ends to verify that all terminals are locked d Rotate the hinged secondary lock inward until tabs fully engage latches on both sides of connector NOTES If the terminal must be removed and reinstalled refer to the MULTILOCK ELECTRICAL CONNECTORS section of the appropriate Service Manual Fill pin cavities in the circuit board with dielectric grease from the packet in the kit before assembling connector halves 5 Connect the socket housing on the new tail stop lamp assembly to the four way pin housing in the circuit board NOTE Do not over tighten screws Over tightening the screws can crack the tail stop lamp lens or scratch the fender paint 6 Install the tail stop lamp to the vehicle Alternately tighten the screws to 20 24 in Ibs 2 3 2 7 Nm NOTE See Figure 1 Lamp assembly 1 attaches as shown on full fender models NOTICE Do not over tighten bolts on battery terminals Use recommended torque values Over tightening baitery ter minal bolts could result in damage to battery terminals 00216a 7 Verify that the ignition light key switch is in the OFF posi tion Models WITH main fuse Refer to the Owner s Manual and follow the instructions to install the main fus
2. MOTOR W J05758 INSTRUCTIONS REV 2015 04 14 LED TAIL LAMP GENERAL Kit Numbers 67800355 67800356 67800357 67800358 67800614 67800615 67800616 67800617 Models For model fitment information see the P amp A Retail Catalog or the Parts and Accessories section of www harley davidson com English only Additional Parts Required NOTE This instruction sheet references service manual information A service manual for your model motorcycle is required for this installation and is available from a Harley Davidson Dealer Kit Contents See Figure 3 and Table 1 INSTALLATION For models WITH main fuse WARNING To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b 1 Refer to the owner s manual and follow the instructions to remove the seat and main fuse Retain all seat mounting hardware For models WITHOUT main fuse IWIN NIN To prevent accidental vehicle start up which could cause death or serious injury disconnect negative battery cable before proceeding 00048a NOTE For 2004 and later XL Sportster models the negative battery cable is most easily disconnected at the engine crankcase 1 Refer to the owner s manual and follow instructions to remove seat and disconnect negative black battery cable from negative battery terminal Retain all seat mounting hardware NOTE Figure 1 shows the o
3. e Models WITHOUT main fuse Connect the negative battery cable per the instructions in the Owner s Manual J05758 Apply a light coat of petroleum jelly or corrosion retardant material to battery terminals Refer to the Owner s Manual and follow the instructions to install the seat WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b WARNING Be sure headlamp tail and stop lamp and turn signals are operating properly before riding Poor visibility of rider to other motorists can result in death or serious injury 00478b 8 Turn the ignition light key switch to ON but do not start motorcycle Check operation of all lamps SERVICE PARTS is08008 Figure 3 Service Parts Table 1 Service Parts Table Item Description Part Number 1 Lens Not sold separately 2 Tail lamp jumper harness 69200905 3 4 way socket housing 73154 96BK 4 5 gram package dielectric grease 76001 04 2 of 2
4. riginal equipment tail stop lamp mounted to a full fender See Figure 1 Loosen the two screws 2 retaining the tail stop lamp assembly 1 to the lamp base 8 Pull the lamp assembly away from the base Push the locking tab button and disconnect the tail stop lamp connector 93B 4 from the circuit board Remove the lamp from the vehicle is02969 l pew SS Tail stop lamp assembly Tail stop lamp retaining screw 2 Tail stop lamp base Tail stop lamp connector 93B 1 2 3 4 Figure 1 Removing the Tail Stop Lamp Assembly is02970a Socket housing Secondary lock Locking tab button Cavity Socket terminal Slot Crimp tails BO SNS Figure 2 Socket Terminal Installation On the new tail stop lamp assembly the wires and socket terminals are not installed in the four way socket housing J05758 Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled 1 of 2 Please dispose of materials responsibly Refer to the original lamp removed in Step 3 and observe which cavity contains which wires The cavities are numbered on the face of the secondary lock The blue red yellow and black wires and terminals must be installed into the same cavities in the socket housing of the new lamp as follows a See Figure 2 On the secondary lock 2 side of the socket housing 1 position the socket terminal 5 with the slot
Download Pdf Manuals
Related Search
Related Contents
Early Education Student System Frequently Asked Questions Manual de usuario para ECOFILM MHF Systemes de radiologie DigitalDiagnost- Philips TAR online timekeeping - Business and Financial Services Craftsman 917.27103 Lawn Mower User Manual Pelco C528M-E Marine Radio User Manual O753K - Northern Lights ColorQuality Dernières acquisitions musique décembre 2009 Contact Center Suite User Guide Copyright © All rights reserved.
Failed to retrieve file