Home

DDM-2000 FiberReach Multiplexer Software Release Description

Contents

1. The SYSCTL resets and the terminal is logged off the system 23 Was response correct If Then Yes Continue with Step 24 No Proceed to Step 30 24 Did the letter C appear in the FE ID display If Then Yes Continue with Step 25 No STOP END OF TASK 8 18 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 25 WARNING If the system is in service and is forced to run the current software that is displaying a C service interruption may result Important Indications are that there may be a problem with the version of software you are installing or you are trying to install a version of software that will not support the current shelf provisioning If you are downloading an older version of software or upgrading to a new version of software which has major changes or is incompatible with the version that you have this indication will occur See Table 8 1 You can force the system to run the current software or back out of this procedure by loading another version of software You must decide if you want the system to run this current version of software that has been loaded or if you want to download another version original version or new version of software Do you want to run the current version of software in the SYSCTL If Then No Continue with Step 26 Yes Proceed to Step 27 26 Exit TERM AIt F2 Find new version of software and repeat
2. double click on the My Computer icon on your desktop Then double click on the CD ROM drive icon Select the component option for running Cterm from the CD ROM and follow the step by step instructions provided by the InstallShield Wizard Refer to DLP 525 for new shelf software installation Lucent Technologies Proprietary 4 7 See Notice on first page Installing Software to an In Service DDM 2000 FiberReach Shelf From the CD ROM Description Perform the following if you want to install software from the CD ROM directly to a DDM 2000 FiberReach local or remote shelf that is currently running a compatible version of software 1 Connect the PC to the CIT port on the DDM 2000 FiberReach shelf User Panel 2 Insert the CD ROM into the disk drive After several seconds the InstallShield Wizard should appear on the PC display If the InstallShield Wizard does not appear double click on the My Computer icon on your desktop Then double click on the CD ROM drive icon 3 Select the component option for running Cterm from the CD ROM and follow the step by step instructions provided by the InstallShield Wizard 4 Referto DLP 536 for Local or DLP 567 for remote download 4 8 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Lucent Technologies Bell Labs Innovations 5 Software Installation Overview Purpose This chapter covers the Implement
3. install SYSCTL Letter E in FE ID Display Indicates SYSCTL must be replaced Get replacement SYSCTL and repeat procedures of DLP 539 Letter F in FE ID Display Indicates SYSCTL faceplate latch is not fully latched Unplug SYSCTL and repeat procedures of DLP 539 Ensure you properly latch the faceplate when installing SYSCTL Flashing Letter L in FEID Indicates a low voltage condition Display brownout on the shelf Clear trouble using Trouble Clearing TAP 119 3 Ensure the PC is connected to the front CIT CIT 1 connector of shelf receiving software If floppies are being used ensure the first number 1 diskette is installed in floppy drive If hard drive is being used ensure you are in the correct directory 109 584 805 Lucent Technologies Proprietary 8 3 Issue 1 June 2005 See Notice on first page Important After the terminal emulator term is started the software download automatically begins The download may take up to 45 minutes Enter term orterm COMn command where n 1 or 2 If term is entered without the COMn option then COMI will be selected by default Disregard message Can t find script lt init gt if you see it after starting the terminal emulator Result Two brief messages are printed and you are instructed to Press any key to continue after the second message After you press any key the terminal emulator is loaded and the terminal responds as follows within 2 minutes CTR
4. shelves in the same control system MJ and FE ACTY LEDs light on User Panel Download begins and the following message is displayed In progress The dots continue to print until program installation is complete After installation is completed the PC prints the following completion message ins prog TID COMPLD Generic a b c is installed The LEDs go off on the User Panel and SYSCTL 11 Was response correct If Then Yes Proceed with Step 29 No Continue with Step 12 12 Wait approximately 5 minutes for network to stabilize then repeat this procedure from Step 7 If the second attempt to download software fails then do Trouble Clearing TAP 116 You may have to go to the remote site 13 Stop END OF TASK 8 26 0 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 14 Important The FE ID display on the remote SYSCTL must show one of the following preceding software installation Other conditions represent failure conditions or conditions that will not allow a remote software download a The letter P displayed in the FE ID display indicates corrupted application software and you may be able to download software from another shelf or locally Try again to download software from same shelf If there is no period after the P the software can only be downloaded locally using the procedures of DLP 536 b Nothing displayed in the FE ID display indicates that compatible soft
5. 3 Ct 3 0 n OC 1 OC 3 U n OC 1 OC 3 U 4 0 n OC 1 OC 3 OC 12 U Note All DDM 2000 FiberReach shelves in a subnetwork should be using TARP Release 3 0 or 4 0 software C Requires local software download only to upgrade the system U Requires local or remote software download only to upgrade the system T Incompatible OSI stack requires special considerations See LTP 824 102 144 Lucent Technologies 2000 Product Family Operations Interworking Guide for TARP Releases for special considerations When doing an upgrade it is recommended that the latest point release of software be used if possible 4 Usertrv fecom set fecom command to verify enable far end communications fecom Important If you want to load new software to a remote shelf if allowed directly from a PC use the ins prog tid command where the tid entered is that of the remote shelf where you want to install the new software and the pgmtype is the type of software you want to install After using the ins prog tid command to 109 584 805 Lucent Technologies Proprietary 8 23 Issue 1 June 2005 See Notice on first page download software to one shelf you must exit term Alt F2 and re execute term before starting a second ins prog command If term is not exited it will stop running if a second ins prog is started within the same t erm session The PC will not respond or return any message and the ins prog will not progress Impo
6. 3 to complete the upgrade 5 8 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Upgrading DDM 2000 FiberReach Release 2 2 to Release 4 0 3 Description Important Software upgrades from DDM 2000 FiberReach Release 2 2 to DDM 2000 FiberReach Release 4 0 3 cannot be done remotely If a NE running DDM 2000 FiberReach Release 2 2 is upgraded to DDM 2000 FiberReach Release 4 0 3 through a Forced Software Download the following scenarios will take place Software of Release 4 0 3 is downloaded and installed as the EXECUTING generic If the ins prog command was initiated to install Release 2 2 to a NE running Release 4 0 3 the following scenarios will take place Software of Release 4 0 3 is downloaded and installed as the EXECUTING generic Refer to DLP 536 for Local download 109 584 805 Lucent Technologies Proprietary 5 9 Issue 1 June 2005 See Notice on first page Upgrading DDM 2000 FiberReach Release 3 0 to Release 4 0 3 Description Important Software upgrades from DDM 2000 FiberReach Release 3 0 to DDM 2000 FiberReach Release 4 0 3 should first be upgraded to an intermediate release of Release 3 1 If a NE running DDM 2000 FiberReach Release 3 0 is upgraded to DDM 2000 FiberReach Release 3 1 through a Forced Software Download the following scenarios will take place Software of Release 3 1 is downloaded and installed as the EXECUTING generic Proceed to
7. 584 805 See Notice on first page Issue 1 June 2005 e This font indicates lettering designations on the backplane shelf and circuit packs Example Release the ACO TEST push button on the SYSCTL when the 8 disappears in the IND display e This font indicates information output by the system or displayed on the computer Example The response will be rtrv eqpt all COMPLD e Underlined phrases indicate hyperlinks to other text in the document or another step in the task Example Cross Reference chapter page number e Important messages are displayed as follows Important This is important information Related information For a complete list of all DDM 2000 documentation contact the products Lucent Technologies Customer Information Center at 1 888 582 3688 or on the internet at http www lucentdocs com The following documents are referenced in this document e DDM 2000 FiberReach Multiplexer Wideband Narrowband Shelf TARP Release 3 0 and Later User Service Manual 363 206 305 The following documents are supplied at the end of this document e DLP 525 Install Software Generic Program New Shelf Installation Only BBG amp BBGSB SYSCTL and BBG9 OHCTL Installed e DLP 536 Install Software Generic Program In Service System Local Shelf Download e DLP 537 Install Software Generic Program In Service System Remote Shelf Download How to comment To comment on this information product go to the Online Co
8. Are you using ins prog orcpy prog command to download software to far end shelf If Then CPY PROG Continue with Step 7 INS PROG Proceed to Step 14 Registered trademark of Microsoft Corporation Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Important Only one cpy prog procedure at a time should be performed in the same maintenance subnetwork Simultaneous cpy prog procedures in the same network may fail Connect and establish session with local shelf being used as a source for the new remote program download Refer to DLP 521 8 Enterthe command cpy prog tid Where tid the target identifier shelf name for the remote DDM 2000 shelf receiving the new program Result Testing For Program Installation After several seconds the PC prints a Caut ion message followed by the prompt Execute y n 9 Was response correct If Then Yes Continue with Step 10 No Do Trouble Clearing TAP 116 109 584 805 Lucent Technologies Proprietary 8 25 Issue 1 June 2005 See Notice on first page 10 Entera y or yes and a carriage return to execute the program Software download may take up to 20 minutes Result ABN LED lights on User Panel A P is displayed in SYSCTL FE ID display in the far end shelf receiving the program At DDM 2000 shelves connected directly to the shelf receiving the program MJ and NE ACTY LEDs light on User Panel At other
9. June 2005 See Notice on first page Release 4 0 3 Feature Descriptions Support for OC 12 Optics 29G U OLIU Support for DS3 services when using 26 type OLIU Main pack Support for 1 1 DCC interworking Support for TL1 on CIT port Supports for OC 12 optics through the use of the 29G U OLIU circuit packs in the Main slots Use of the 29G U OLIU allows the following e STS I STS 3c VTI 5 Pass Through cross connections on the 29G U equipped FiberReach shelves e STS 1 cross connections between main slots equipped with the 29G U OLIU and Function Unit slots providing a fully flexible assignment of STS 1 timeslots The function unit slots must be equipped with the BBG4 BBG4B DS3 or the BBG19 DS3 circuit packs for STS 1 cross connections e VTI 5cross connections between Main slots equipped with 29G U OLIU circuit packs and Low Speed slots equipped with DS1 HDSL or TI EXT circuit packs providing fully flexible VT1 5 timeslot assignment e STS 3c 0X1 cross connections when the shelf is equipped with the 29G U OLIU circuit packs in Main slots and 22 type OLIU packs in the Function Unit slots e OC I12 Section and Line performance monitoring PM data will be collected and reported Threshold crossing alerts for the PM data will also be provided e OC 12 Line level alarms will be monitored and reported e In service upgrades from 28G U OC 3 OLIU circuit pack to the new 29G U OLIU circuit pack Supports the B
10. Release 4 0 3 Software CD ROM Create a set of Distribution Disks 4 3 Extracting Software and Software Release Description to a PC Hard Drive 4 4 Create Icon to Download Release 4 0 3 Software from Desktop 4 5 Create Icon to Download Release 4 0 3 Software from Desktop for PCs Arranged to use COM2 4 6 Installing Software to a New DDM 2000 FiberReach Shelf From the CD ROM 4 7 109 584 805 Lucent Technologies Proprietary CONTENTS Issue 1 June 2005 See notice on first page iii Installing Software to an In Service DDM 2000 FiberReach Shelf From the CD ROM 4 8 5 Software Installation In Service Upgrades 3 3 Implementation Procedure 5 4 Upgrading DDM 2000 FiberReach Release 1 0 to Release 4 0 3 5 6 Upgrading DDM 2000 FiberReach Release 2 0 to Release 4 0 3 35 7 Upgrading DDM 2000 FiberReach Release 2 1 to Release 4 0 3 35 8 Upgrading DDM 2000 FiberReach Release 2 2 to Release 4 0 3 5 9 Upgrading DDM 2000 FiberReach Release 3 0 to Release 4 0 3 5 10 Upgrading DDM 2000 FiberReach Release 3 1 to Release 4 0 3 3 11 Upgrading DDM 2000 FiberReach Release 4 0 to Release 4 0 3 3 12 6 DDM 2000 Interworking DDM 2000 Interworking 6 2 7 Miscellaneous Information on Technical Assistance 7 2 Software Ordering Information T 3 8 Reference Commands and Procedures DLP 525 Install Software Generic Program Network Element Software New Shelf Installation Only BBG8 BBG8B SYSCTL Installed 8 2 DLP 536 Install New Software Generic Progr
11. Table 6 2 DDM 2000 OC 12 and DDM 2000 FiberReach WBS Software Release Interconnecting Circuit Pack DDM 2000 DDM 2000 DDM 2000 FiberReach OC 12 FiberReach DOM NO 4 0 Ring 7 0 7 1 28G U OLIU in Main 21G U OLIU in Fn Ring 29G U OLIU in Main 23G U OLIU in Main 109 584 805 Issue 1 June 2005 Lucent Technologies Proprietary See Notice on first page 6 4 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Lucent Technologies Bell Labs Innovations 7 Miscellaneous Overview Purpose This chapter contains various miscellaneous information concerning the DDM 2000 FiberReach Release 4 0 3 software Contents This chapter contains the following Information on Technical Assistance 7 2 Software Ordering Information 1 3 109 584 805 Lucent Technologies Proprietary 7 1 Issue 1 June 2005 See Notice on first page Information on Technical Assistance Technical Assistance Many of our customers have established their own support procedures These procedures usually involve escalation within their own companies However some issues may require additional assistance from Lucent Technologies Lucent Technologies has been and continues to be committed to providing excellence in technical customer support for its products and services Therefore we provide a hierarchical support structure ready and available to solve any DDM 2000 FiberReach Multiplexer t
12. Upgrading DDM 2000 FiberReach Release 3 1 to Release 4 0 3 to complete the upgrade If the ins prog command was initiated to install Release 3 1 in a NE running Release 3 0 software the following scenarios will take place Software of Release 3 1 is downloaded and installed as the EXECUTING generic Proceed to Upgrading DDM 2000 FiberReach Release 3 1 to Release 4 0 3 to complete the upgrade If the cpy prog command was initiated to copy Release 3 1 into a remote NE running Release 3 0 software the following scenarios will take place Software of Release 3 1 is downloaded and installed as the EXECUTING generic of the NE receiving the software Proceed to Upgrading DDM 2000 FiberReach Release 3 1 to Release 4 0 3 to complete the upgrade Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Upgrading DDM 2000 FiberReach Release 3 1 to Release 4 0 3 Description If a NE running DDM 2000 FiberReach Release 3 1 is upgraded to DDM 2000 FiberReach Release 4 0 3 through a Forced Software Download the following scenarios will take place Software of Release 4 0 3 is downloaded and installed as the EXECUTING generic If the ins prog command was initiated to install Release 4 0 3 in a NE running Release 3 1 software the following scenarios will take place Software of Release 4 0 3 is downloaded and installed as the EXECUTING generic If the cpy prog command
13. appear on the PC display 2 Select the component option to install the software onto your hard drive and follow the step by step instructions provided by the InstallShield Wizard 3 The Software Release Description documentation will be installed in a folder in C Program Files Lucen DDM 2000 F R_R403 Documentation 4 Release 4 0 3 Software will be installed in the C Program Files Lucen DDM 2000 FR_R403 folder 4 4 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Create Icon to Download Release 4 0 3 Software from Desktop Description Perform the following if you want to Create Icon to Download Release 4 0 3 Software from Desktop 1 Right mouse click on the desktop click on New gt Shortcut and the Create Shortcut Window will open 2 Click on the Browse button then double click the appropriate drive and the Program Files Lucent DDM 2000 and FR_R403 Folders Click on the Term then click 0K then click Next In the Select a name for the shortcut window Type in FiberReach Release 4 0 3 in the window and click the Finsh Button 109 584 805 Lucent Technologies Proprietary 4 5 Issue 1 June 2005 See Notice on first page Create Icon to Download Release 4 0 3 Software from Desktop for PCs Arranged to use COM2 Description Perform the following if you want to Create Icon to Download Release 4 0 3 Software from Desktop using COM2 1 Right mouse
14. as an AGNE provision co existing OC 3 shelves as AGNES instead Security Enhancements Supports new Security enhancements to the NE which includes a user provisionable field of about 400 characters to display a proprietary notice after logging in a password aging feature on all user accounts that would make users change their password when or before it expires and may be provisioned to have up to 147 non privileged logins and three priveleged logins 109 584 805 Lucent Technologies Proprietary E 23 Issue 1 June 2005 See Notice on first page 1 4 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Lucent Technologies Bell Labs Innovations 2 Problems Fixed Overview Purpose This chapter provides descriptions of problems found in previous releases and fixed in Release 4 0 3 Contents This chapter contains the following Problems Fixed in Release 4 0 1 2 2 Problems Fixed in Release 4 0 3 2 3 109 584 805 Lucent Technologies Proprietary 2 1 Issue 1 June 2005 See Notice on first page Problems Fixed in Release 4 0 1 Transmission The following problems corresponding to Transmission functionality have been fixed Issue When the FiberReach 3 1 2 WBS is equipped with a BBG4 or BBG4B DS3 circuit pack in the FUNCTION UNIT the CIT command rtrv pm ststl with the AID m 1 is not accepted Similarly the TL1 command sched pmrept sts1 is denied for the AID m 1
15. click on the desktop click on New gt Shortcut and the Create Shortcut Window will open 2 Click on the Browse button then double click the appropriate drive and the Program Files Lucent Ddm 2000 and FR R403 Folders Click on the Term click 0K then click Next In the Select a name for the shortcut window Type in FiberReach Release 4 0 3 in the window and click the Finish Button 3 Right mouse click on the icon created above and select Properties from the drop down list 4 The OC3 Release 4 0 3 Properties window will open 5 On the Shortcut tab in the Target text box type in COM2 following the term bat Example C ProgramFiles Lucent Ddm 2000NFR R403Nterm bat com2 4 6 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Installing Software to a New DDM 2000 FiberReach Shelf From the CD ROM 109 584 805 Issue 1 June 2005 Important If your PC is configured to download DDM 2000 software using COM2 Release 4 0 3 software cannot be downloaded to a shelf directly from a CD ROM Perform the following if you want to install software from the CD ROM directly to a DDM 2000 FiberReach shelf that is not equipped with software Connect the PC to the CIT port on the DDM 2000 FiberReach shelf User Panel Insert the CD ROM into the disk drive After several seconds the InstallShield Wizard should appear on the PC display If the InstallShield Wizard does not appear
16. from the 28G U OC 3 type OLIU circuit pack to the 29G U OC 12 type OLIU circuit pack the FiberReach system might detect STS 1 LOP alarm conditions on STS 1 numbers four through twelve Workaround Reset the FiberReach system that initiates transmits these alarm conditions Operations Interworking The following problems corresponding to Operations Interworking functionality have been observed Issue In the event that the LATLIF parameter is found to be set to a value of 0 reprovisioning it to a valid value cannot be done via the TL 1 command ENT ULSDCC L4 Workaround Reprovision the LATLIF parameter to the correct default value of 100 via the CIT interface using the ENT ULSDCC L4 command 109 584 805 Lucent Technologies Proprietary 9 709 Issue 1 June 2005 See Notice on first page 3 4 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Lucent Technologies Bell Labs Innovations 4 Using the Release 4 0 3 Software CD ROM Overview Purpose 109 584 805 Issue 1 June 2005 DDM 2000 Release 4 0 3 software can be ordered on diskettes or CD ROM This section provides procedures to be used when utilizing a CD ROM as the media to access and distribute Release 4 0 3 software Important Software Download is not guaranteed on PCs running Windows XP Operating Systems because CTERM is a DOS application and Windows XP no longer guarantees support of DOS applications
17. was initiated to copy Release 4 0 3 into a remote NE running Release 3 1 software the following scenarios will take place e Software of Release 4 0 3 is downloaded and installed as the EXECUTING generic of the NE receiving the software Refer to DLP 536 for Local or DLP 567 for remote download 109 584 805 Lucent Technologies Proprietary 5 11 Issue 1 June 2005 See Notice on first page Upgrading DDM 2000 FiberReach Release 4 0 to Release 4 0 3 Description If a NE running DDM 2000 FiberReach Release 4 0 is upgraded to DDM 2000 FiberReach Release 4 0 3 through a Forced Software Download the following scenarios will take place Software of Release 4 0 3 is downloaded and installed as the EXECUTING generic If the ins prog command was initiated to install Release 4 0 3 in a NE running Release 4 0 software the following scenarios will take place Software of Release 4 0 3 is downloaded and installed as the EXECUTING generic If the cpy prog command was initiated to copy Release 4 0 3 into a remote NE running Release 4 0 software the following scenarios will take place Software of Release 4 0 3 is downloaded and installed as the EXECUTING generic of the NE receiving the software Refer to DLP 536 for Local or DLP 567 for remote download Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Lucent Technologies Bell Labs Innovations 6 DDM 2000 Inter
18. 2 2 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Problems Fixed in Release 4 0 3 Operations The following problems corresponding to System Operations functionality have been fixed Issue DCC can fail in such a way that network elements connected to the failed shelf may be affected resulting in DCC failures in the attached network elements The DCC failure may clear and then fail again later Issue Occasionally on 28 type and 29 type OLIUs the series number is overwritten by software with the result of changing the to some unspecified character Example from showing a S1 1 to SI 1 Hardware The following problems corresponding to System Operations functionality have been fixed Issue The BBG8B Ser 1 3 Controller fails due to excessive writing of the Controllers EEPROM by the software When the EEPROM s write limit is reached the software is no longer able to write to that location and the Controller is tagged as failed 109 584 805 Lucent Technologies Proprietary P DEM Issue 1 June 2005 See Notice on first page 2 4 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 3 Lucent Technologies Bell Labs Innovations Known Problems Overview Purpose This chapter provides descriptions of known problems and workarounds for problems that exist in the DDM 2000 FiberReach Multiplexer Important These Known Problems
19. BG4 BBG4B DS3 and the BBG19 DS3 circuit packs in the Function Unit slots of the FiberReach shelf while using the 26 type OC 1 OLIU circuit pack in the Main slots Supports the Main ring OC 3 OC 12 interfaces DCC provisioning to the values of distinct default or identical For normal ring connections the Main interfaces will use the distinct DCC mode The identical DCC mode will allow a FiberReach shelf to interconnect through its Main interface to an OC 3 OC 12 1 1 interface on another NE e g Function Unit of the host NE Supports the provisioning of asynchronous CIT port to run TL1 This feature allows the system to accept TL1 message size of up to 3022 characters A maximum of 50 remote TL1 associations may be initiated from the CIT port Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Support for Remote NE Supports remote NE status using Alarm Gateway NE AGNE When Status an NE is provisioned as an AGNE this feature provides remote office alarms and summary alarm information of remote Network Elements in the local alarm report The FiberReach NE may be provisioned as a GNE or an AGNE however it is recommended that it not be provisioned as both at the same time The recommended maximum number of Network Elements in an alarm group containing a FiberReach as an AGNE is 15 Important In networks where an Alarm Group size is greater than 15 NEs do not provision FiberReach
20. C 1 OC 3 U n OC 1 OC 3 U 4 0 n OC 1 OC 3 OC 12 U Note All DDM 2000 FiberReach shelves in a subnetwork should be using TARP Release 3 0 or 4 0 software C Requires local software download only to upgrade the system U Requires local or remote software download only to upgrade the system T Incompatible OSI stack requires special considerations See LTP 824 102 144 Lucent Technologies 2000 Product Family Operations Interworking Guide for TARP Releases for special considerations When doing an upgrade it is recommended that the latest point release of software be used if possible Important If you are using a PC operating in a Windows environment you must exit Windows and restart your PC in MS DOS mode before performing these download procedures For example if your PC is running Windows 95 you must exit Windows by clicking on the Start button then Shut Down then Restart the computer in MS DOS mode Obtain equipment check software and connect PC for download Refer to DLP 541 A Registered trademark of Microsoft Corporation Lucent Technologies Proprietary 8 9 See Notice on first page 5 Observe one of the following indications on the FE ID display Note the indication and follow the suggested procedure If Letter P in FE ID Display Letter P in FE ID Display FE ID Display Blank Letter C in FE ID Display Letter U in FE ID Display Letter E in FE ID Display 8 10
21. Lucent Technologies Bell Labs Innovations DDM 2000 FiberReach Multiplexer Software Release Description Release 4 0 3 109 584 805 Issue 1 June 2005 Lucent Technologies Proprietary This document contains proprietary information of Lucent Technologies and is not to be disclosed or used except in accordance with applicable agreements Copyright 2005 Lucent Technologies Unpublished and Not for Publication All Rights Reserved This material is protected by the copyright and trade secret laws of the United States and other countries It may not be reproduced distributed or altered in any fashion by any entity either internal or external to Lucent Technologies except in accordance with applicable agreements contracts or licensing without the express written consent of Lucent Technologies and the business management owner of the material For permission to reproduce or distribute please contact Product Development Manager 1 317 322 6847 1 800 645 6759 continental U S Notice Every effort was made to ensure that this information product was complete and accurate at the time of printing However information is subject to change Mandatory customer information Interference information Part 15 of FCC rules NOTE This equipment is designed to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfer
22. Lucent Technologies Proprietary See Notice on first page Then Indicates no software installed in SYSCTL Software must be downloaded locally using these procedures Continue with Step 6 Letter P followed by a period indicates a previous download attempt has failed New software must be downloaded locally using these procedures Proceed to Step 21 Indicates compatible software is installed on the SYSCTL This procedure assumes the installed software version is not the correct version Depress ACO button for longer than 2 seconds to display software version on the FE ID display Proceed to Step 9 Indicates software is installed in SYSCTL but it will not support the current shelf provisioning Proceed to Step 25 Indicates SYSCTL switches S1 and S2 are not set properly for type of shelf being equipped Remove SYSCTL Repeat procedures of DLP 501 to correct switch settings and to install SYSCTL Indicates SYSCTL must be replaced Get replacement SYSCTL and repeat procedures of DLP 501 109 584 805 Issue 1 June 2005 If Letter F in FE ID Display Flashing Letter L in FE ID Display Then Indicates SYSCTL faceplate latch is not fully latched If SYSCTL has just been replaced unplug SYSCTL and repeat procedures of DLP 501 If original SYSCTL has just been unplugged and reseated properly seat the faceplate latch A reset occurs after the faceplate is latched Indicate
23. M ready Type Alt h for help Communications established Searching for optimal transfer rate Handshake established at lt baudrate gt baud In progress The dots continue to print until program installation is complete If using floppies insert each diskette when prompted After installation is completed the PC prints the following completion message ins prog TID COMPLD Generic a b c is installed The SYSCTL resets and the terminal is logged off the system 5 Was response correct If Then Yes STOP END OF TASK No Proceed to Step 10 8 4 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 109 584 805 Issue 1 June 2005 Ensure PC is connected to the front CIT CIT 1 connector of shelf receiving software If floppies are being used ensure the first number 1 diskette is installed in floppy drive If hard drive is being used ensure you are in the correct directory Enter term or term COMn command where n 1 or 2 If term is entered without the COMn option then COMI will be selected by default If after starting the terminal emulator you see the message Can t find script lt init gt disregard it Result Two brief messages are printed and you are instructed to Press any key to continue after the second message After you press any key the terminal emulator is loaded and the terminal responds as follows CTRM ready Type Alt h for help Commun
24. Result PC prompts with Enter a shelf number from 1 to 8 shelf default Was response correct If Then Yes Continue with Step 12 No Proceed to Step 31 Enter the shelf number for the shelf being used for new program download Result PC prompts with Login Enter the privileged user login default LUCO1 Result PC prompts with Password Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 14 Enter the privileged user password default DDM 2000 Result PC responds with J FCKCKCKCkCk kk Ck Ck Ck Ck kk Ck Ck kk Ck kk Ck Ck ck ck kokokckck ck ck ck ck kokok Lucent Technologies DDM 2000 FiberReach i Release a b c CK CKCk Ck CkCck ck Ck ck kCk ck kCk ck kCk ck ck ck ck ck ck k ck ck kk ck k k k kk TID date time M rtrv alm a COMPLD Active Alarms and Status Report 15 Important After the system prompt lt the system will respond normally to commands entered The Commands and Reports section of Volume 1 of DDM 2000 FiberReach Multiplexer Wideband Narrowband Shelf TARP Release 3 0 and Later User Service Manual 363 206 305 gives a description of the commands Use rtrv ne command to retrieve the name tid of the shelf having new program installed or see TID in response above 109 584 805 Lucent Technologies Proprietary 8 15 Issue 1 June 2005 See Notice on first page 16 Ent
25. The CD ROM contains a Windows based InstallShield Wizard that provides step by step instruction for extracting software from the CD ROM The InstallShield Wizard can be used to e Create a set of software distribution disks e Copy software files to a directory on the PC hard drive e Download software directly from the CD ROM to a DDM 2000 shelf e Download a PDF file of the Software Release Description to the PC hard drive If you want to create a set of software disks proceed to the Create a Set of Distribution Disks Section Lucent Technologies Proprietary 4 1 See Notice on first page If you want to copy software files and a pdf file of the Software Release Description from the CD ROM to the PC hard drive proceed to the Extracting Software and Software Release Description to a PC Hard Drive Section If you want to download software directly to a new DDM 2000 shelf proceed to the Installing Software to a New DDM 2000 Shelf From the CD ROM Section If you want to download software directly to an in service DDM 2000 shelf proceed to the Installing Software to an In Service DDM 2000 Shelf From the CD ROM Section Contents This chapter contains the following Create a set of Distribution Disks 4 3 Extracting Software and Software Release Description to a 4 4 PC Hard Drive Create Icon to Download Release 4 0 3 Software from 4 5 Desktop Create Icon to Download Release 4 0 3 Software from 4 6 Desktop fo
26. am Network Element Software In Service System Local Shelf Download 8 8 DLP 537 Install New Software Generic Program Network Element Software Remote Shelf Download In Service System 8 22 CONTENTS Lucent Technologies Proprietary 109 584 805 iv See notice on first page Issue 1 June 2005 Lucent Technologies Bell Labs Innovations About this information product Purpose Reason for reissue Safety labels How to use this information product 109 584 805 Issue 1 June 2005 The purpose of this Software Release Description SRD is to provide information about DDM 2000 FiberReach Multiplexer Release 4 0 3 This document is intended for individuals who are responsible for the installation acceptance operations and maintenance of the DDM 2000 FiberReach This is the first issue of this document This document may contain a safety label in the form of a CAUTION statement This admonishment has the following definition N CAUTION Caution indicates the presence of a hazard that will or can cause minor personal injury or property damage if the hazard is not avoided The Caution Admonishment is also used for equipment damage loss of software or service interruption Important Read all chapters of this document before beginning the DDM 2000 FiberReach Release 4 0 3 software installation or upgrade The following is a brief description of the contents of each chapter in this document Lucent Technologies Proprieta
27. as well as others that are discovered after this document is issued are listed as solutions in the Technical Support Services TSS ask Lucent Knowledge database In order to access this database the user must have a Remote Technical Support RTS contract To view the entries in the ask Lucent Knowledge database 1 he a ae a Go to http www lucent com support Enter and submit login information Click ask Lucent Knowledge Database Wait until the screen loads Enter index of srd known problems in the Ask question field Select DDM 2000 Click Go Click on DDM 2000 FiberReach Release 4 0 3 SRD Known Problems 109 584 805 Issue 1 June 2005 Lucent Technologies Proprietary 3 1 See Notice on first page Contents This chapter contains the following Known Problems 3 3 3 x2 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Known Problems Maintenance The following problems corresponding to Maintenance functionality have been observed Issue In the DS3 services that have been provisioned for vm or vmr modes a DS3 AIS signal should be transmitted towards the DSX when an incoming STS 1 unequipped signal is detected on the high speed channel which is cross connected to that DS3 service In this release of the product no DS3 AIS signal will be transmitted towards the DSX under that failure condition Workaround Be aware Issue During an upgrade
28. ation of Release 4 0 3 on the DDM 2000 FiberReach Multiplexer Contents This chapter contains the following In Service Upgrades 5 2 Implementation Procedure 5 3 Upgrading DDM 2000 FiberReach Release 1 0 to Release 5 5 4 0 3 Upgrading DDM 2000 FiberReach Release 2 0 to Release 5 6 4 0 3 Upgrading DDM 2000 FiberReach Release 2 1 to Release 5 7 4 0 3 Upgrading DDM 2000 FiberReach Release 2 2 to Release 5 8 4 0 3 Upgrading DDM 2000 FiberReach Release 3 0 to Release 5 9 4 0 3 Upgrading DDM 2000 FiberReach Release 3 1 to Release 5 10 4 0 3 109 584 805 Lucent Technologies Proprietary 5 1 Issue 1 June 2005 See Notice on first page Upgrading DDM 2000 FiberReach Release 4 0 to Release 5 11 4 0 3 5 2 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 In Service Upgrades Description Table 5 1 lists the current software releases of the DDM 2000 FiberReach Multiplexer that can be directly upgraded while in service Specific procedures for upgrades are provided in 363 206 305 DDM 2000 FiberReach Multiplexer Wideband Narrowband Shelf TARP Release 3 0 and Later User Service Manual TOP Volume II Table 5 1 DDM 2000 FiberReach In Service Software Upgrade Compatibility Upgrade to Current Release 4 0 1 0 n OC 1 cit 2 0 n OC 1 ce 2 1 n OC 1 cit 2 2 n OC 1 OC 3 ci 3 0 n OC 1 OC 3 U 3 1 n OC 1 OC 3 U 4 0 n OC 1 OC 3 OC 12 U Notes When
29. baud rate is currently set to 9600 change it to 4800 or if the baud rate is currently set to 4800 change it to 9600 The baud rate is changed by a Momentarily depress the Alt C keys b Use the RETURN key to move to the Speed field c Press the Space bar until the desired rate appears d Momentarily depress the Esc Escape key to activate the new baud rate 7 If the download still does not start refer to Trouble Clearing TAP 116 32 Stop END OF TASK 33 Ifthe download starts and fails during its progress exit term Alt F2 and then restart a new term session 34 Unplug and reseat the SYSCTL and immediately push and hold the FE SEL and UPD INIT buttons at the same time until a P appears in the FE ID display takes approximately 15 seconds If the download still does not complete refer to Trouble Clearing TAP 116 END OF STEPS 109 584 805 Lucent Technologies Proprietary 8 21 Issue 1 June 2005 See Notice on first page DLP 537 Install New Software Generic Program Network Element Software Remote Shelf Download In Service System Outline Procedure Use the following procedure to remotely download FiberReach software to a BBGS BBGSB SYSCTL for an in service system Before beginning the software installation refer to the Software Installation and Upgrade Procedure section of the Software Release Description This section contains a description of any special considerations required when insta
30. d Where tid the target identifier shelf name for the far end DDM 2000 shelf having the new program installed Result Testing For Program Installation After several seconds the PC prints a Caution message followed by the prompt Execute y n 24 Was response correct If Then Yes Continue with Step 25 No Do Trouble Clearing TAP 116 25 Enteray oryes anda carriage return to execute the program Software download may take up to 45 minutes Result ABN LED lights on User Panel A P is displayed in SYSCTL FE ID display in the far end shelf receiving the program PC starts download and prints the following message Searching for optimal transfer rate Handshake established at lt baudrate gt baud In progress The dots continue to print until program installation is complete If floppy disks are being used insert each diskette when prompted After installation is completed the PC prints the following completion message ins prog TID COMPLD Generic a b c is installed The SYSCTL resets and the terminal is logged off the system The LEDs go off on the User Panel and SYSCTL 8 30 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 26 27 28 29 30 31 32 Was response correct If Then Yes Proceed with Step 29 No Continue with Step 27 Wait approximately 5 minutes for the network to stabilize exit term then r
31. doing an upgrade it is recommended that the latest point release of software be used if possible t Incompatible OSI stack requires special upgrade procedure See 363 206 285 DDM 2000 OC 3 Multiplexer TARP Release 13 and Later User Service Manual TOP Volume II and 842 102 144 Lucent Technologies 2000 Product Family Operations Interworking Guide For TARP Releases for subnetwork upgrade procedures Requires local software download only to upgrade the system Requires local or remote software download only to upgrade the system Requires upgrade to R2 2 prior to upgrading to R4 0 Requires upgrade to R3 1 prior to upgrading to R4 0 109 584 805 Lucent Technologies Proprietary Se 3 Issue 1 June 2005 See Notice on first page Implementation Procedure Description Important Software Download is not guaranteed on PCs running Windows XP Operating Systems because CTERM is a DOS application and Windows XP no longer guarantees support of DOS applications Important After Release 4 0 3 or any other DDM 2000 FiberReach TARP software release has been installed and is the operating generic for the shelf use the RTRV ULSDCC L4 command to verify that the LATLIF parameter is correctly provisioned with a default value of 100 If instead the LATLIF parameter is set to 0 set it to 100 using the ENT ULSDCC L4 command Verify that the LAETDC parameter is set to enable If it is set to disable set it to enable u
32. e 4 0 3 to complete the upgrade If the ins prog command was initiated to install Release 2 2 to a NE running Release 2 0 the following scenarios will take place Software of Release 2 2 is downloaded and installed as the EXECUTING generic e Proceed to Upgrading DDM 2000 FiberReach Release 2 2 to Release 4 0 3 to complete the upgrade 109 584 805 Lucent Technologies Proprietary 5 7 Issue 1 June 2005 See Notice on first page Upgrading DDM 2000 FiberReach Release 2 1 to Release 4 0 3 Description Important Software upgrades from DDM 2000 FiberReach Release 2 1 to DDM 2000 FiberReach Release 4 0 3 should first be upgraded to an intermediate release of Release 2 2 Important Software upgrades from DDM 2000 FiberReach Release 2 1 to DDM 2000 FiberReach Release 2 2 cannot be done remotely If a NE running DDM 2000 FiberReach Release 2 1is upgraded to DDM 2000 FiberReach Release 2 2 through a Forced Software Download the following scenarios will take place e Software of Release 2 2 is downloaded and installed as the EXECUTING generic e Proceed to Upgrading DDM 2000 FiberReach Release 2 2 to Release 4 0 3 to complete the upgrade If the ins prog command was initiated to install Release 2 2 to a NE running Release 2 1 the following scenarios will take place Software of Release 2 2 is downloaded and installed as the EXECUTING generic e Proceed to Upgrading DDM 2000 FiberReach Release 2 2 to Release 4 0
33. echnical issue When additional technical assistance is needed the Lucent Technologies Customer Technical Assistance Management CTAM is your first point of contact Technical assistance is available 24 hours a day 7 days a week Lucent Technologies Customer Technical Assistance Management CTAM 1 866 LUCENT 8 1 866 582 3688 24 hours a day 7 days a week Outside the continental US customers should call 1 630 224 4672 or contact the Local Customer Support LCS or the support organization designated by their Customer Team By using CTAM as the entry point for Lucent Technologies support you will be assured of timely and effective technical support services Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Software Ordering Information Description The following table refers to the Software ordering information Comcode Description 109 584 821 DDM 2000 FiberReach Multiplexer R4 0 3 CD ROM with software program 109 584 839 DDM 2000 FiberReach Multiplexer R4 0 3 Initial Application 109 584 847 DDM 2000 FiberReach Multiplexer R4 0 3 Software Upgrade Application 109 584 805 DDM 2000 FiberReach Multiplexer R4 0 3 Software Release Description Paper 109 584 813 DDM 2000 FiberReach Multiplexer R4 0 3 Software Release Description CD ROM 109 584 805 Lucent Technologies Proprietary dou Issue 1 June 2005 See Notice on first page P Lucent Tec
34. ectory If floppies are being used ensure the first number 1 diskette is installed in floppy drive Ensure PC is connected to the front CIT CIT 1 connector Enter term or term COMnr command where n 1 or 2 If term is entered without the COM n option then COM1 will be selected by default Disregard message Can t find script init if you see it after starting the terminal emulator Important Two brief messages are printed and you are instructed to Press any key to continue after the second message After you press any key the terminal emulator is loaded and the terminal responds as follows CTRM ready Type Alt h for help Communications established 109 584 805 Lucent Technologies Proprietary 8 17 Issue 1 June 2005 See Notice on first page 22 Unplug and reseat the SYSCTL and immediately push and hold the FE SEL and UPD INIT buttons at the same time until a P appears in the FE ID display takes approximately 15 seconds The software download automatically begins and may take 20 to 45 minutes Result PC starts download and prints the following message Searching for optimal transfer rate Handshake established at lt baudrate gt baud In progress The dots continue to print until program installation is complete If using the floppy disks insert each diskette when prompted After installation is completed the PC prints the following completion message ins prog TID COMPLD Generic a b c is installed
35. ence when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications Operation of this equipment in a residence is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Security statement In rare instances unauthorized individuals make connections to the telecommunications network through the use of access features In such an event applicable tariffs require that the customer pay all network charges for traffic Lucent Technologies and its predecessors cannot be responsible for such charges and will not make any allowance or give any credit for charges that result from unauthorized access Trademarks SESS and Billdats are registered trademarks of Lucent Technologies in the United States and other countries Information Mapping is a registered trademark of Information Mapping Inc Limited warranty For terms and conditions of sale contact your Lucent Technologies Account Team Ordering information The ordering number for this document is 109 584 805 To order this document call 1 888 582 3688 USA 1 317 322 6619 Canada 1 317 322 6416 Europe the Middle East and Africa or 1 317 322 6411 Asia the Pacific Region China Caribbean and Latin America RBOC BOC customers should
36. epeat this procedure from Step 14 If the second attempt to download software fails do Trouble Clearing TAP 116 You may have to go to the remote site Wait approximately 5 minutes then verify communications can be reestablished with far end shelf using rtrv map network command Verify that Comm Status is good not FAILED as indicated by a blank in the report Is communication status good between local and remote shelf If Then Yes Proceed with Step 32 No Continue with Step 31 Dispatch technician to remote site and perform local software download procedures Refer to DLP 532 Stop END OF TASK END OF STEPS 109 584 805 Issue 1 June 2005 Lucent Technologies Proprietary 8 31 See Notice on first page 8 32 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005
37. er the command ins prog tid Where tid the target identifier shelf name for the DDM 2000 shelf having the new program installed Result Testing For Program Installation After several seconds the PC prints a Caution message followed by the prompt Execute y n 17 Wasresponse correct If Then Yes Continue with Step 18 No Do Trouble Clearing TAP 116 18 Enteray or yes anda carriage return to execute the program Software download may take 20 to 45 minutes Result ABN LED lights on User Panel and a P is displayed in SYSCTL FE ID display in the shelf receiving the program PC starts download and prints the following message Searching for optimal transfer rate Handshake established at lt baudrate gt baud In progress The dots continue to print until program installation is complete If floppy disks are being used insert each diskette when prompted After installation is completed the PC prints the following completion message ins prog TID COMPLD Generic a b c is installed 8 16 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 19 Was response correct If Then Yes Continue with Step 20 No Do Trouble Clearing TAP 116 20 Didthe letter C appear in the FE ID display If Then Yes Proceed to Step 25 No STOP END OF TASK 21 Important If PC hard drive is being used ensure you are in the correct dir
38. f a NE running DDM 2000 FiberReach Release 1 0 is upgraded to DDM 2000 FiberReach Release 2 2 through a Forced Software Download the following scenarios will take place e Software of Release 2 2 is downloaded and installed as the EXECUTING generic e Proceed to Upgrading DDM 2000 FiberReach Release 2 2 to Release 4 0 3 to complete the upgrade If the ins prog command was initiated to install Release 2 2 to a NE running Release 1 0 the following scenarios will take place Software of Release 2 2 is downloaded and installed as the EXECUTING generic e Proceed to Upgrading DDM 2000 FiberReach Release 2 2 to Release 4 0 3 to complete the upgrade 5 6 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Upgrading DDM 2000 FiberReach Release 2 0 to Release 4 0 3 Description Important Software upgrades from DDM 2000 FiberReach Release 2 0 to DDM 2000 FiberReach Release 4 0 3 should first be upgraded to an intermediate release of Release 2 2 Important Software upgrades from DDM 2000 FiberReach Release 2 0 to DDM 2000 FiberReach Release 2 2 cannot be done remotely If a NE running DDM 2000 FiberReach Release 2 0 is upgraded to DDM 2000 FiberReach Release 2 2 through a Forced Software Download the following scenarios will take place Software of Release 2 2 is downloaded and installed as the EXECUTING generic e Proceed to Upgrading DDM 2000 FiberReach Release 2 2 to Releas
39. hnologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Lucent Technologies Bell Labs Innovations 8 Reference Commands and Procedures Overview Purpose This chapter provides the commands and procedures referenced in this SRD Contents This chapter contains the following DLP 525 Install Software Generic Program Network 8 2 Element Software New Shelf Installation Only BBG8 BBG8B SYSCTL Installed DLP 536 Install New Software Generic Program Network 8 8 Element Software In Service System Local Shelf Download DLP 537 Install New Software Generic Program Network 8 22 Element Software Remote Shelf Download In Service System 109 584 805 Lucent Technologies Proprietary 8 1 Issue 1 June 2005 See Notice on first page DLP 525 Install Software Generic Program Network Element Software New Shelf Installation Only BBG8 BBG8B SYSCTL Installed Outline Procedure 1 2 2 Use the following procedure to download FiberReach software to a BBGS BBGS8B SYSCTL for a new shelf installation Important This procedure is used to install a software program in a new DDM 2000 FiberReach shelf equipped only with the BBGS BBGS8B SYSCTL circuit pack The circuit pack may be new from the factory or a circuit pack used previously that may already be loaded with software For procedures to download software locally to a fully equipped in service shelf see DLP 536 For procedures to download software remotely to a fully e
40. ications established Unplug and reseat the SYSCTL and immediately push and hold the FE SEL and UPD INIT buttons at the same time until a P appears in the FE ID display approximately 15 seconds Software download may take up to 45 minutes Result PC starts download and prints the following message Searching for optimal transfer rate Handshake established at lt baudrate gt baud In progress The dots continue to print until program installation is complete If using the floppy disks insert each diskette when prompted After installation is completed the PC prints the following completion message ins prog TID COMPLD Generic a b c is installed Lucent Technologies Proprietary 8 5 See Notice on first page The SYSCTL resets and the terminal is logged off the system After approximately three minutes you can log into the system If Then Yes STOP END OF TASK No Proceed to Step 10 10 Did the download start as indicated by the In Progress message and rows of dots If Then Yes Proceed to Step 18 No Continue with Step 11 11 Check that the DDM 2000 is connected to the PC through the COM port If it is not reconnect the PC to DDM 2000 using the COM port and repeat the procedure If the download still does not start as indicated by the In Progress message and rows of dots within 2 minutes after the P appears in the FE ID display change the CTRM baud rate as follows and repeat this p
41. lled The SYSCTL resets and the terminal is logged off the system 8 12 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 7 Was response correct If Then Yes Continue with Step 8 No Proceed to Step 30 8 Didthe letter C appear in the FE ID display If Then No STOP END OF TASK Yes Proceed to Step 25 Important If PC hard drive is being used ensure you are in the correct directory If floppies are being used ensure the first number 1 diskette is installed in floppy drive Enter term or term COMn command where n 1 or 2 If term is entered without the COMn option then COMI will be selected by default Disregard message Can t find script init if you see it after starting the terminal emulator Result Two brief messages are printed and you are instructed to Press any key to continue after the second message After you press any key the terminal emulator is loaded and the terminal responds as follows CTRM ready Type Alt h for help Communications established 109 584 805 Lucent Technologies Proprietary 8 13 Issue 1 June 2005 See Notice on first page 10 11 12 13 Important The default shelf is the shelf physically connected to the PC To set baud rate automatically enter two carriage returns cr two lower case a s aa or two upper case A s AA All other characters are ignored Enter two carriage returns
42. lling this version of software Important This procedure uses the cpy prog or ins prog commands to install a new software program in a remote in service DDM 2000 FiberReach shelf It is assumed that the local shelf has already been upgraded and the software is running normally For procedures to download software in a new shelf initial installation see DLP 525 For procedures to download software locally to a shelf see DLP 536 Important If upgrading from earlier software releases to TARP Release 3 0 and later after the first shelf is upgraded single ended operations will not be available and major alarms section DCC channel failed will exist until all shelves are upgraded The node farthest away should be upgraded first working back to the local node See 824 102 144 Lucent Technologies 2000 Product Family Operations Interworking Guide For TARP Releases for guidelines in subnetwork upgrade procedures Verify that no DCC failures or transmission failures OC 1 LOS OC 3 LOS OC 12 LOS flashing OLIU FAULT LEDs etc are present on the network element or system receiving the program Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 3 For software upgrade compatibility see Table 8 2 Table 8 2 DDM 2000 FiberReach In service Software Upgrade Compatibility Upgrade to Current Release 4 0 3 1 0 n OC 1 Ct 2 0 n OC 1 Ct n OC 1 Ct 2 2 n OC 1 OC
43. mment Form or email your comments to the Comments Hotline comments Q lucent com 109 584 805 Lucent Technologies Proprietary vii Issue 1 June 2005 See Notice on first page How to order From Country Region USA Canada North American Region NAR Europe the Middle East and Africa EMEA Asia Pacific Region and China Caribbean Latin America CALA This section describes how to order e Additional copies of this document Electronic documentation CD ROMs ILEC CLEC Customers ILEC CLEC customers should process orders through your Company Documentation Coordinator Commercial Customers Commercial customers may order standard documentation or request placement on the standing order list for reissues of any document by mail telephone fax email or the internet The postal address for CIC is Lucent Technologies Attention Order Entry 2855 N Franklin Road P O Box 19901 Indianapolis IN 46219 Table 1 Ordering Documentation via Phone Fax or Email Telephone Fax Numbers Email Numbers 1 888 LUCENT 8 1 800 566 9568 cicorders lucent com 1 888 582 3688 1 317 322 6616 1 317 322 6699 cicorders lucent com 1 317 322 6416 1 317 322 6699 intlnaorders lucent com Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Table 2 Ordering Documentation via the Internet Customer Web Site Commercial Customers http www lucentdocs com http ww
44. nnections Make sure the cable is connected between the PC COM port and the CIT connector on the DDM 2000 Check term setup and make sure the com port selected matches the port COM on the PC that is connected to the CIT port on the shelf Exit term Alt F2 and repeat this procedure from Step 14 Enter the shelf number for the local shelf being used for new program download Result PC prompts with Login Enter the privileged user login default LUCO1 Result PC prompts with Password Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 21 Enter the privileged user password default DDM 2000 Result PC responds with J a kk Ck Ck Ck Ck kk Ck Ck kk Ck kk CK kk kk kc k ck ck ck kokokckckok Lucent Technologies DDM 2000 FiberReach Release a b c OKCKCKCkCk ck kckckckck Ck Ck ck ck kckckck ck kckckckck ck ck ck I Ik ae kk f TID date time M rtrv alm all COMPLD Active Alarms and Status Report 22 Important After the system prompt the system will respond normally to commands entered The Commands and Reports section of this manual gives a description of the commands Usertrv map network command to retrieve the name t id of the remote shelf having new program installed 109 584 805 Lucent Technologies Proprietary 8 29 Issue 1 June 2005 See Notice on first page 23 Enter the command ins prog ti
45. on refer to the Software Installation and Upgrade Procedure section of the Software Release Description This section contains a description of any special considerations required when installing this version of software Important This procedure is used to install a new software program in a local in service DDM 2000 FiberReach shelf For procedures to download software in a new shelf initial installation see DLP 525 For procedures to download software to a remote shelf using ins prog or cpy prog command see DLP 537 Important Ifupgrading from earlier non TARP software releases to TARP Release 3 0 and later after the first shelf is upgraded single ended operations will not be available and major alarms section DCC channel failed will exist until all shelves are upgraded The node farthest away should be upgraded first working back to the local node Verify that no DCC failures or transmission failures OC 1 LOS OC 3 LOS OC 12 LOS flashing OLIU FAULT LEDs etc are present on the network element or system receiving the program Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 109 584 805 Issue 1 June 2005 3 For software upgrade compatibility see Table 8 1 Table 8 1 DDM 2000 FiberReach In service Software Upgrade Compatibility Upgrade to Current Release 4 0 3 1 0 n OC 1 Ct 2 0 n OC 1 Ct n OC 1 Ct 2 2 n OC 1 OC 3 Ct 3 0 n O
46. process document orders or standing order requests through their Company Documentation Coordinator For more ordering information refer to the Ordering Information section in the About This Information Product section Support Information product support Lucent Technologies provides a referral telephone number for support Use this number to report errors or to ask questions about the information in this product This is a non technical number The referral number is 1 800 645 6759 or 1 317 322 6848 Technical support Lucent Technologies Customer Technical Assistance Management CTAM center provides a technical assistance telephone number that is monitored 24 hours a day For technical assistance continental U S call 1 866 LUCENTS 1 866 582 3688 and select the appropriate prompt For international customers please call 1 630 224 4672 Developed by Lucent Technologies Technical Support Services TSS Lucent Technologies Proprietary See Notice on first page Lucent Technologies Bell Labs Innovations Contents About this information product Purpose Y Reason for reissue M Safety labels v How to use this information product v Conventions used vi Related information products vii How to comment vii How to order viii 1 Features Release 4 0 3 Feature Descriptions 1 2 2 Problems Fixed Problems Fixed in Release 4 0 1 2 2 Problems Fixed in Release 4 0 3 2 3 3 Known Problems Known Problems 3 3 4 Using the
47. quipped in service shelf see DLP 537 Important Itis assumed that the BBG8 BBG8B SYSCTL circuit pack has been installed per DLP 539 Important If you are using a PC operating in a Windows environment you must exit Windows and restart your PC in MS DOS mode before performing these download procedures For example if your PC is running Windows 95 you must exit Windows by clicking on the Start button then Shut Down then Restart the computer in MS DOS mode Obtain equipment check software and connect PC for download Refer to DLP 541 in the DDM 2000 FiberReach Multiplexer Wideband Narrowband Shelf TARP Release 3 0 and Later User Service Manual 363 206 305 Observe one of the following indications on the FE ID display Note the indication and follow the suggested procedure Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 If Then Letter P in FE ID Display Indicates no software installed in SYSCTL Software must be downloaded locally using these procedures Continue with Step 3 Letter P in FE ID Display Letter P followed by a period indicates a previous download attempt has failed New software must be downloaded locally using these procedures Proceed to Step 6 Letter U in FE ID Display Indicates SYSCTL switches S1 and S2 are not set properly for type of shelf being equipped Remove SYSCTL Repeat procedures of DLP 539 to correct switch settings and to
48. r PCs Arranged to use COM2 Installing Software to a New DDM 2000 Shelf From the CD 4 7 ROM Installing Software to an In Service DDM 2000 Shelf From 4 8 the CD ROM 4 2 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Create a set of Distribution Disks Description Perform the following procedure if you want to create a set of software distribution disks Labeling Disks Obtain four 3 5 disks that have been formatted Label the disks as follows e Diskl DDM 2000 FiberReach Release 4 0 3 Disk 1 of 4 e Disk2 DDM 2000 FiberReach Release 4 0 3 Disk 2 of 4 e Disk3 DDM 2000 FiberReach Release 4 0 3 Disk 3 of 4 e Disk4 DDM 2000 FiberReach Release 4 0 3 Disk 4 of 4 Extracting Software to Disks 1 Insert the CD ROM into the disk drive After several seconds the InstallShield Wizard will appear on the PC display 2 Select the software extraction component to create a set of floppy disks by following the step by step instructions provided by the InstallShield Wizard 109 584 805 Lucent Technologies Proprietary IE Issue 1 June 2005 See Notice on first page Extracting Software and Software Release Description to a PC Hard Drive Description Perform the following if you want to copy software files and the Software Release Description from the CD ROM to the PC hard drive 1 Insert the CD ROM into the disk drive After several seconds the InstallShield Wizard will
49. rocedure If the baud rate is currently set to 9600 change it to 4800 or if the baud rate is currently set to 4800 change it to 9600 The baud rate is changed by Momentarily depress the Alt C keys Using the RETURN key to move to the Speed field Pressing the Space bar until the desired rate appears anon org Momentarily depressing the Escape Esc key to activate the new baud rate 12 Ensure first number 1 disk of program being installed is inserted if using floppies 8 6 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 14 15 16 17 18 Ensure the proper command was used to go to the drive with the diskette or to the proper directory containing the software Check for invalid COM port Exit TERM Alt F2 then restart TERM using term COMI or term COM2 116 If the download starts and fails during its progress exit term Alt F2 and repeat this procedure from STEP 6 If the download still does not start refer to Trouble Clearing TAP 116 END OF STEPS 109 584 805 Issue 1 June 2005 Lucent Technologies Proprietary 8 7 See Notice on first page DLP 536 Install New Software Generic Program Network Element Software In Service System Local Shelf Download Outline Procedure Use the following procedure to locally download FiberReach software to a BBG8 BBG8B SYSCTL for an in service system Before beginning the software installati
50. rtant If remote software downloading is allowed and you want to load new software to a remote site via the DCC from a local shelf which already contains the new software log in either locally or remotely to the shelf containing the new software and then enter the cpy prog tid command where tid the tid of the shelf in which you want to install the software and the pgmtype is the type of software you want to install The tid is the name given to a shelf network element using the set ne command The cpy prog command will only copy software from a local controller to a remote controller it is not used to download software from a PC Important The download time will be longer even without excessive DCC traffic when there are additional spans between the source and target network elements To minimize the download time and reduce DCC traffic it is recommended that multi span software downloading be avoided by remotely logging into the nearest shelf of the same type and remotely downloading the new program from that shelf Important If you are using a PC operating in a Windows environment you must exit Windows and restart your PC in MS DOS mode before performing these download procedures For example if your PC is running Windows 95 you must exit Windows by clicking on the Start button then Shut Down then Restart the computer in MS DOS mode Obtain equipment check software and connect PC for download Refer to DLP 566
51. ry V See Notice on first page Conventions used Chapter 1 Features This chapter provides a listing of DDM 2000 FiberReach Multiplexer features for Release 4 0 3 Chapter 2 Problems Fixed This chapter provides brief descriptions of fixes to problems found in prior releases Chapter 3 Known Problems This chapter provides descriptions and workarounds for problems existing in Release 4 0 3 Chapter 4 Using the Release 4 0 3 Software CD ROM This chapter provides the procedures to install the NE software Chapter 5 Software Installation This chapter provides the procedures to install the DDM 2000 FiberReach Multiplexer Release 4 0 3 software into a new system Chapter 6 DDM 2000 Interworking This chapter covers interworking between DDM 2000 FiberReach Multiplexer Release 4 0 3 and other PF 2000 family software Chapter 7 Miscellaneous This chapter provides technical support software ordering information Chapter 8 Reference Commands and Procedures This chapter provides the commands and procedures referenced in this SRD The following conventions are used in this document e This font indicates a command Example ent crs stsl e This font indicates a document reference Example Document Title xxx xxx xxx ordering number DDM 2000 OC 3 and OC 12 Multiplexers Applications Planning and Ordering Guide 363 206 200R15 Lucent Technologies Proprietary 109
52. s a low voltage condition brownout on the shelf Clear trouble using Trouble Clearing TAP 119 109 584 805 Issue 1 June 2005 Lucent Technologies Proprietary See Notice on first page Important If PC hard drive is being used ensure you are in the correct directory If floppies are being used ensure the first number 1 diskette is installed in floppy drive Ensure PC is connected to the front CIT CIT 1 connector Important After the terminal emulator term is started the software download automatically begins The download may take 20 to 45 minutes Enter term or term COMn command where n 1 or 2 If term is entered without the COMn option then COMI will be selected by default Disregard message Can t find script init if you see it after starting the terminal emulator Result Two brief messages are printed and you are instructed to Press any key to continue after the second message After you press any key the terminal emulator is loaded and the terminal responds as follows within 2 minutes CTRM ready Type Alt h for help Communications established Searching for optimal transfer rate Handshake established at lt baudrate gt baud In progress The dots continue to print until program installation is complete If using floppies insert each diskette when prompted After installation is completed the PC prints the following completion message ins prog TID COMPLD Generic a b c is insta
53. sing the ENT ULSDCC L4 command The following is a brief description of scenarios that may be encountered while upgrading to DDM 2000 FiberReach Release 4 0 3 software DDM 2000 FiberReach Release 1 0 1 through 1 0 5 2 0 1 2 1 1 and 2 1 2 shelves using the BBG8 System Controller SYSCTL circuit pack manufactured in June 1997 or earlier are susceptible to developing corrupted memory locations in the controller s boot flash devices that can result in the loss of controller functionality in the event of a software reboot When upgrading from any of the above releases run the test sysct 1 command on the DDM 2000 to be upgraded Refer to Engineering Change Procedure ECP N81076MV for more information Important Performance of the test sysct1 command will not affect shelf operation However if the controller fails the test the shelf will indicate a Major Alarm SYSCTL FAIL until the defective controller is replaced A controller failing this test will continue to function properly as long as a shelf software reboot does not occur A software reboot will result in the failed controller becoming inoperative Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 109 584 805 Issue 1 June 2005 DLP 536 and DLP 537 contain the latest information and procedures needed for upgrading a DDM 2000 FiberReach System running any upgradable version of DDM 2000 FiberReach software DLP 525 contains the late
54. software releases DDM 2000 FiberReach Release 4 0 3 is targeted specifically for large subnetworks and multi vendor applications See 824 102 144 Lucent Technologies 2000 Product Family Operations Interworking Guide For TARP Releases for more information on operations interworking Table 6 1 lists the DDM 2000 FiberReach WBS software compatibility and interconnections with the DDM 2000 OC 3 Multiplexers All configurations listed support operations interworking OI The table lists all possible software combinations Combinations not listed are not supported Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Table 6 1 DDM 2000 OC 3 and DDM 2000 FiberReach WBS Software Release Interconnecting Circuit Pack DDM 2000 DDM 2000 DDM 2000 FiberReach OC 3 FiberReach rt OC 4 0 Ring 15 0 15 1 28G U OLIU in Main 22 Type OLIU in Main 15 3 Ring 26G2 U OLIU in Main 26G2 U 27G2 U OLIU in Fn 29G U OLIU in Main 24G U 29G U OLIU in Main 13 0 Ring 28G U OLIU in Main 22 Type OLIU in Main 26G2 U OLIU in Main 26G2 U 27G2 U OLIU in Fn DDM 20000C 12 Software Compatibility Table 6 2 lists the DDM 2000 FiberReach WBS software compatibility and interconnections with the DDM 2000 OC 12 Multiplexers All configurations listed support operations interworking OI The table lists all possible software combinations Combinations not listed are not supported
55. st information and procedures needed to installing software in new shelf installations where the SYSCTL is new and contains no software This release of software takes approximately 15 to 25 minutes to download to a local shelf using a newer PC with the autobaud feature This release of software takes approximately 45 minutes to download to a local shelf using an older PC set to 9600 baud This release of software copying software from one shelf to another takes about 15 to 20 minutes The download time will be longer even without excessive DCC traffic when there are additional spans between the source and target network elements To install the new software use the attached copies of e DLP 525 Install Software Generic Program Network Element SoftwareNew Shelf Installation Only BBG8 BBGS amp B SYSCTL Installed e DLP 532 Install Software Generic Program In Service System Local Shelf Download e DLP 562 Install Software Generic Program In Service System Remote Shelf Download Lucent Technologies Proprietary 5 5 See Notice on first page Upgrading DDM 2000 FiberReach Release 1 0 to Release 4 0 3 Description Important Software upgrades from DDM 2000 FiberReach Release 1 0 to DDM 2000 FiberReach Release 4 0 3 should first be upgraded to an intermediate release of Release 2 2 Important Software upgrades from DDM 2000 FiberReach Release 1 0 to DDM 2000 FiberReach Release 2 2 cannot be done remotely I
56. this procedure from Step 21 109 584 805 Lucent Technologies Proprietary 8 19 Issue 1 June 2005 See Notice on first page 27 28 29 30 31 N WARNING Removing the main 1 OLIU with a C displayed on the SYSCTL may result in a service outage To force the system to run the current software remove the OLIU in slot main 1 then reset unplug and reseat the SYSCTL to force it to run the current software OLIU Did the download start as indicated by the In progress message and rows of dots If Then No Continue with Step 31 Yes Proceed to Step 33 Perform the following 1 Check that the DDM 2000 is connected to the PC through the COM port If it is not reconnect the PC to DDM 2000 using the COM port and repeat this procedure 2 Ensure first number 1 disk of program being installed is inserted if using floppies 3 Ensure diskette is inserted in correct drive Ensure the proper command was used to go to the drive with the diskette or to the proper directory containing the software 5 Check for invalid COM port Exit TERM Alt F2 then restart TERM using term COMI orterm COM2 Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 6 If the download still does not start as indicated by the In progress message and rows of dots within 2 minutes after the P appears in the FE ID display change the baud rate as follows and repeat this procedure if the
57. w lucent8 com Lucent Associates http www cic lucent com Methods of Payment Lucent Associates are billed using an organization number cost center and location code Commercial customers may use one of the following methods of payment Check payable to Lucent Technologies Money order payable to Lucent Technologies Invoice upon receipt of a purchase order Purchase orders may be faxed or mailed using the information provided above Credit card Visa MasterCard American Express For orders totaling 1000 or less either a credit card or prepayment by check money order is required 109 584 805 Issue 1 June 2005 Lucent Technologies Proprietary ix See Notice on first page X Lucent Technologies Proprietary 109 584 805 See Notice on first page Issue 1 June 2005 Lucent Technologies Bell Labs Innovations 1 Features Overview Purpose This chapter describes the features of the DDM 2000 FiberReach Multiplexer Release 4 0 3 For a complete listing of features supported in DDM 2000 FiberReach please refer to the DDM 2000 FiberReach Multiplexer Applications Planning and Ordering Guide 363 206 300 and the DDM 2000 FiberReach Multiplexer Wideband Narrowband Shelf TARP Release 3 0 and Later User Service Manual 363 206 305 Contents This chapter contains the following Release 4 0 3 Feature Descriptions 1 2 109 584 805 Lucent Technologies Proprietary l 1 Issue 1
58. ware is installed in the SYSCTL and you may download software remotely if remote software downloading is permitted for this release Ensure PC is connected to the front CIT CIT 1 If floppies are being used ensure the first number 1 diskette is installed in floppy drive If hard drive is being used ensure you are in the correct directory 15 Enter term or term COMn command where n 1 or 2 If term is entered without the COMn option then COMI will be selected by default If after starting the terminal emulator you see the message Can t find script init disregard it Result Two brief messages are printed and you are instructed to Press any key to continue after the second message After you press any key the terminal emulator is loaded and the terminal responds as follows CTRM ready Type Alt h for help Communications established 109 584 805 Lucent Technologies Proprietary 8 27 Issue 1 June 2005 See Notice on first page 16 17 18 19 20 Important The default shelf is the shelf physically connected to the PC To set baud rate automatically enter two carriage returns cr two lower case a s aa or two upper case A s AA All other characters are ignored Enter two carriage returns Result PC prompts with Enter a shelf number from 1 to 8 shelf default Was response correct If Then Yes Proceed with Step 19 No Continue with Step 18 Check PC to CIT port co
59. working Overview Purpose This chapter covers interworking between DDM 2000 FiberReach Multiplexer Release 4 0 3 and other PF 2000 family software Contents This chapter contains the following DDM 2000 Interworking 6 2 109 584 805 Lucent Technologies Proprietary 6 1 Issue 1 June 2005 See Notice on first page DDM 2000 Interworking Introduction DDM 2000 OC 3 Software Compatibility Interworking between products is evolving to include both transmission interworking with EC 1 OC 1 OC 3 IS 3 and DS3 interfaces and operations interworking OI Multi vendor transmission interworking was supported in previous releases DDM 2000 FiberReach Release 4 0 3 supports multi vendor OI compatibility Care must be taken to check correct software releases and to check interface provisioning For OLIU interfaces care must be taken to ensure that both ends of a span are provisioned equipped for the same protection mode 1 1 or dual Ox1 for example The following tables list the software compatibility within a subnetwork for the DDM 2000 FiberReach Multiplexer with Release 4 0 3 software All configurations listed support OI The tables list all possible Lucent Technologies software combinations Software combinations not listed are not supported The tables reflect that DDM 2000 OC 3 Release 4 0 3 is not expected to be deployed in the same networks as earlier non TARP DDM 2000 OC 12 FiberReach FT 2000 or DDM 2000 FiberReach

Download Pdf Manuals

Related Search

Related Contents

Manual del usuario BT-450  取扱説明書 - 三菱電機  Lenovo 3000 V200 User's Manual  HGB-509 / HGB-510 / HGB-609 FLUID REGULATOR SB  Dossier à l`usage des pharmaciens hospitaliers  DeLOCK 62622  My Passport User Manual  Enerium 50-150 operating manual  Bedienungsanleitung  Broan 6201 Fan User Manual  

Copyright © All rights reserved. Failed to retrieve file