iPod INSTALLATION INSTRUCTIONS
Contents
1. back towards the hood release lever again Wrap cable s around the LH U shaped frame where the foam tape was placed and back towards the mounting location Fig 7 9 Repeat steps 7 amp 8 again and complete routing at module mounting location 10 Leave cable s dangling until the module installation later 11 Secure the bundled cable s with two 2 cable ties around the bundle and the C channel Fig 8 cable ties 5 9 999U7 XT100Il 3 1 4 07 FRONTIER PATHFINDER 1 CABLE ROUTING iPod CABLE amp XTERRA 1 Using a 1 8 bit drill a pilot hole in the bottom LH side in the rear of the upper glove box 19mm 2mm 0 75in from both nearby edges of the box Open up the hole to 11 16 Fig 9 amp 10 2 Mark the cable 460mm 18 125 from the iPod end f rectangular connector Start routing iPod cable from detail of area in Fig 10 inside of glove box with DIN connector end round ba connector Route out of glove box through the drilled hole Place grommet over wire and feed into drilled hole in glove box A PGF stick or other plastic prying tool may be helpful Fig 10 3 Re install the upper glove box per the service manual 4 With glove box re installed pull the cable until the mark on the cable is equal with the grommet Route cable into cavity behind HVAC controls to other side of IP 5 Leaving enough room to connect to the iPod module bundle the excess cable 5 6 loop Wrap electrical t2. Fig 14 amp 15 Z CAUTION Ensure that the large cable ties do not wrap around any other cables or objects horizontal cross member NOTE The mini DIN connector will have interference issues if the chassis is not placed high enough bolt to attach ground cable 7 Wrap cable ties around vertical c channel Tighten the cable ties as much as possible to minimize movement Plug the cables into the assembly Fig 14 amp 15 8 Take the ground wire tapped off of the N bus harness and route towards bolt to the left of module mounting location Fig 16 9 Use an 10mm socket to remove the bolt Insert the NE TER module mounting location eyelet connector Tighten the bolt back down to secure the eyelet Fig 16 7 9 999U7 XT100II 3 1 4 07 FRONTIER PATHFINDER 13 OPERATION CHECK amp XTERRA 1 Connect the battery negative terminal 2 Turn vehicle ignition switch to the ACC position 3 Reference the vehicle specific Satellite Radio Installation Instructions for further information If Satellite radio was part of installation turn radio on then select satellite radio mode Acquiring Sirius or Loading XM will display for a while If not move vehicle to outside and try again 4 If Satellite radio was part of installation tune to preview channel XM channel 1 Sirius channel 184 to make sure receiving preview channel correctly For Sirius tuner installations the preview channel may not be accessibl
3. Lussan GENUINE PARTS D A m iPod INSTALLATION INSTRUCTIONS 1 DESCRIPTION iPod 2 PART NUMBERS iPod Gateway Module Kit 07 999U7 VR002 iPod Gateway Module Kit 05 06 999U7 VROOO N Bus harness for iPod Gateway 999U7 VS000 N Bus harness for optional SAT Radio 999U7 VS001 Pe cabletie 17 re Cable tie T5 6 D Double Sided Tape 1 LE Foam Tae Jo LT Quick Reference Card 1 5 PRE INSTALLATION CAUTIONS NOTES CAUTION Dealer installation recommended This installation instruction will reference the service manual Cut the excess cable tie s as flush with the head as possible Face head of cable tie away from sheet metal and other objects Use caution when removing re installing interior components to avoid damage scratches or breaking of mounting clips NOTE This is a universal installation kit so all parts may not be used Refer to the vehicle specific SAT radio Installation Instructions on ASIST NET for further information Ensure the Owners Manual and Quick Reference Card are placed in the customers glove box Check the customer s iPod to make sure it has the most current software version before starting the install www apple com ipod In the event the iPod system needs to be serviced order the iPod Service Kit below iPod Gateway Service Kit 999U7 VS002SP 999U7 XT100Il 3 1 4 07 FRONTIER PATHFINDER amp XTERRA TOOLS amp MATERIALS REQUIRED M
4. ape around the bundle in two 2 places for at least two 2 revolutions Secure the bundle with two 2 cable ties to the harness below the upper glove box Fig 11 6 Secure cable near module with one 1 cable tie to harness directly to the right of the module mounting location Fig 12 ers TW cable tie 6 9 999U7 XT100Il 3 1 4 07 FRONTIER PATHFINDER 12 iPod GATEWAY MOUNTING amp XTERRA 1 Using the provided alcohol wipe clean the bottom of the module and mounting location Attach provided double sided tape to bottom of chassis Do not peel off the tape protector on the other side yet 2 Thread the two 2 large cable ties through the holes in the chassis from right to left when orientated as shown connectors towards you Ensure that the cable ties are pulled through with no slack and the head is pulled right up to chassis Fig 13 3 Attach another two 2 large cable ties one to each of the threaded cable ties from the previous step Fig 13 4 Cut the threaded cable ties from step 2 even with the head of the cable ties from step 3 Fig 13 5 Temporarily remove any cable tie clips from the vertical c channel mounting location to provide more clearance 6 Peel the other tape protector off of the double sided tape Now the assembly can be put into place It is to be located on vertical c channel frame above the cross member that runs horizontally Both cable ties should be above that cross member
5. asking tape Drill Phillips screwdriver 2 1 8 11 16 drill bits Plastic Pry bar Electrical tape PGF Stick 4 driver w 10mm socket CRITICAL INSTALLATION STEPS 1 Make sure there are no interference issues when routing harnesses around the parking brake mechanism 2 Ensure the module is mounted level with or above the horizontal cross member to avoid interference with the iPod cable 8 INSTALLATION OUTLINE Vehicle Front SAT Pre wired N Bus harness iPod Gateway Module Satellite Radio 999U7 VS000 iPod Cable Tuner optional iPod upper glove box 999U7 VS001 optional Head Unit 2 9 999U7 XT100Il 3 1 4 07 FRONTIER PATHFINDER amp XTERRA 9 VEHICLE PREPARATION 1 Apply parking brake 2 Record the customer radio presets Preset 1 2 3 el or cad 3 Make sure that the shift lever is engaged in the P position 4 if equipped move the adjustable accelerator brake pedals to the front most position 5 Turn the ignition switch OFF 6 Open engine hood 7 Disconnect the battery negative terminal to prevent short circuits during installation 8 Remove the following interior parts as shown in Fig 3 Refer to vehicle service manual Apply masking tape to interior parts adjacent to parts being removed a Front pillar lower finisher LH RH b Lower driver instrument panel LH c Lower Glove Box assembly d Upper Glove Box assembly y Front pillar lower f
6. d cable Confirm the audio system is otherwise OK AM FM CD works normally Can SAT be selected on the audio system Push the SAT button if present If no SAT button push Radio NO SAT is shown on the audio display Is an iPod connected After pushing Radio display says NO AM FM AM YES Update iPod connections to latest version od SAT vo vis modules NO YES Does iPod have check No further mark screen diagnosis needed Connections Okay NO OK to disconnect Fix Disconnect amp reconnect iPod Cycle Ignition Replace iPod Does iPod have check module mark screen gt iPod _ Is music playing from iPod Reconnect iPod OK to disconnect No further Is music diagnosis playing from iPod Is iPod software the latest version Call TECH LINE for further diagnosis Does radio show RADIO ID gt NO IPOD Check connections to iPod amp SAT modules See service bulletin for Nissan Satellite Radio Diagnostic Information needed See apple com ipod Disconnect iPod Reboot iPod Press amp Hold center button amp Menu button simultaneously until Apple Screen appears Reconnect iPod Does iPod have check mark screen _ Pod 2 va OK to disconnect Is music playing from iPod NOTE When the iPod battery is very low it is possible that the system will not be able to charge it The sys
7. e For further information reference the Operation Check section of the vehicle specific Satellite Radio Installation Instructions 5 Confirm proper audio operation AM FM SAT TAPE CD 6 Confirm accelerator pedal function per service manual 7 If no iPod is present the head unit display should show NO IPOD If an iPod is connected to the system a check mark should be displayed on the iPod screen and audio should start playing in 5 20 seconds 8 A full diagnostic tree is available on the next page for troubleshooting the system 14 REINSTALLATION OF REMOVED PARTS 1 Re install all removed vehicle parts referring to the service manual for the vehicle N CAUTION Use caution when re installing interior components to avoid damage scratches or breaking of mounting clips Refer to the vehicle specific service manual for more information a 2 Clean interior of vehicle 15 FINAL INSPECTION a 1 Inspect the vehicle interior and exterior for damage a 2 Confirm proper operation of vehicle systems a 3 Reset radio presets to the recorded settings a 4 If equipped verify proper sunroof operation and perform the reset procedure if necessary Refer to Service Manual requirements 5 Place the Owners Manual and Quick Reference Card in the customers glove box 8 9 999U7 XT100Il 3 1 4 07 NISSAN IPOD INTERFACE DIAGNOSTIC FLOW CHART Verify iPod module is installed by looking in glove box for iPo
8. inisher LH RH Lower driver instrument panel LH Lower Glove Box Upper Glove Box 3 9 999U7 XT100Il 3 1 4 07 FRONTIER PATHFINDER 10 CABLE ROUTING iPod GATEWAY amp OPTIONAL SATELLITE RADIOJ amp XTERRA 1 Insert the corresponding connector of the iPod gateway harness into the vehicle s prewired N Bus From vehicle s N Bus prewired connector start by routing above the rear section of the hood release lever mechanism and into the C channel to the right of the hood release Optional Connect corresponding connector of the Satellite harness to the correct tuner connector Route cable the same as iPod gateway harness Fig 3 amp 4 2 Secure the prewire and Optional satellite bus cable with one 1 cable tie around the large harness that the prewire originates from Fig 3 amp 4 bs 3 Wrap one 1 piece of foam tape around the JA connectors of the prewire and iPod N Bus Harness 4 Fig 3 amp 4 ha AE e S Vehicle Front 4 Ensure the cable is not interfering with the hood release and is as tight as possible against the metal frame Fig 4 amp 5 5 Place two 2 pieces of foam tape on the front inner section of the U shaped frames Fig 6 6 Route cable s along the C channel to the mounting location area 7 Wrap the cable s 2 times around the RH U shaped frame where the foam tape was placed Fig 6 4 9 999U7 XT100Il 3 1 4 07 FRONTIER PATHFINDER amp XTERRA 8 Route cable s
9. tem may not work at all in this case If this occurs please try to charge your iPod using the iPod power adapter No further diagnosis needed 9 9 999U7 XT100lI 3 1 4 07
Download Pdf Manuals
Related Search