Home
Door Swing Hdw 8.1
Contents
1. disengages 3 Remove the bottom shoot bolt guide and shoot bolt in the same manner Remove the lock box hardware from the old panel by first unscrewing the two 8x 1 flathead brass screws attaching the cover plate to the panel Remove the plate and set aside 7 23 03 19972157 2 2005 With the locking hardware in the unlocked position remove the two 8x 5 8 panhead screws fastening the box to the panel Pry the box out and set aside If the old shoot bolt has the sound dampening washers attached simply peel the foam dampeners from the rod NOTE Some special size height rods may have dampeners attached with plastic ties remove these with a wire cutter and discard 8 Insert the lock box in the new panel and fasten with screws removed earlier Fasten the cover plate to the panel as well With the locking hardware in the locked position insert the top shoot bolt into the panel at an angle so that the end of the bolt with the hex nut is riding along the exterior side of the panel The shoot bolt will have to be threaded through the intermediate foam block as shown in illustration 4 Marvin Service Manual 11708609 MARVIN ad Doors SWINGING DOORS HARDWARE INSWING AND OUTSWING FRENCH DOORS LOCKING ROD REPLACEMENT cn 7 0 AND HIGHER MANUFACTURED AFTER 5 3 03 IMPORTANT If you meet resistance STOP immediately Back the bolt out and try again until it is threaded through the foam block
2. It is possible to miss the groove on the foam block causing the block to detach from the panel and be pushed down toward the lock box If this is the case it will be 15 Built around you Insert a push stick that is approximately 3 4 as long as the panel into the sill shoot bolt channel through the mortise lock area and push the foam block back into position Do not remove the push stick See illustration 7 MARVINA Windows and Doors nearly impossible to thread the bolt into the lock box See il lustration 5 below Ifthe block is pushed down the panel cav ity see the section on repositioning the foam block at the end of this instruction ES x b oe rs Dis A z as ae D k Sr de D Se r k Tan r Ga ON Ee f i Pi si T NOTE Sill bolt channel is 5 8 x 5 8 16 x 16 Use a wooden lt PVC pipe of appropriate dimension that will fit in channel 16 Thread the head jamb shoot bolt through the foam block as described in step 9 from previous section See illustration 8 10 Once threaded through the foam block continue to push the bolt until it tracks and threads into the mortise lock See illustration 6 Turn the shoot bolt until tight then back off two full turns 17 Once through keep threading the bolt until you can feelthe end contacting the mortise lock area Remove the push stick and replace the mortise lock and cover plate Thread both shoot bolts into the mortise lock until tight b
3. SWINGING DOORS HARDWARE INSWING AND OUTSWING FRENCH DOORS LOCKING ROD REPLACEMENT cn 7 0 AND HIGHER MANUFACTURED AFTER 5 3 03 Windows a Built around you ATTENTION As of May 5 2003 Inswing and Outswing French Doors with a CN of 7 0 or greater gt 86 1 2 R O will be manufactured in units with a longer top locking rod If your replacement panel did not come with locking hardware new shoot bolt guides must be used in conjunction with the old locking rod s To fix rod rattle on doors shorter than 7 0 simply remove old shoot bolt guides and replace with new style see below Old shoot bolt guide with a new foam plug within the FRP stile This foam plug is designed with use of the shoot bolt guide to minimize rattling New shoot bolt guide NOTE Photographs below show the panel stile cut away for illustrative purposes With the hardware in the unlocked position remove the top shoot bolt guide from old Shoot Bolt Installation 1 SENS panel by unfastening y the 8x1 1 2 Phillips panhead screw from the guide See illustration 1 Pry the shoot bolt guide from the panel with a flat headed screwdriver or pry bar See illustration 2 Move the hardware to the locked position so the shoot bolt is accessible Turn the shoot bolt counter clockwise until it from the lock box Remove the shoot bolt from the old panel See illustration 3
4. ack off two full turns and replace the shoot bolt guides 11 Replace the shoot bolt guide and fasten with screw removed earlier 12 Thread the sill shoot bolt into the new paneland lock box and tighten Back off two full turns Repositioning the HJ Shoot Bolt Foam Block 13 Should the head jamb shoot bolt foam block be pushed down the panel cavity to the lock box corrective action must be taken before the shoot bolt will track and eventually thread into the lock box 14 Ifnotalready done remove the head jamb shoot bolt sill shoot bolt shoot bolt guides mortise lock and cover plate See previous section 2 2005 Marvin Service Manual 11708609
Download Pdf Manuals
Related Search
Related Contents
Hampton Bay 79132 Installation Guide Form A6188 - Well Control User Program Bedienungsanleitung BAMBI BUCKET SERVICE MANUAL Manuel d`utilisation et de maintenance Plieuses à fil Copyright © All rights reserved.
Failed to retrieve file