08 MBE 4000-1 Rev
Contents
1. Cylinder Head Bolt 3 Special Tool J 41065 2 Special Tool PT 2250 B 4 Cylinder Block Figure 10 Cutting Tool 9 Install two opposing cylinder head bolts with the washers and spacers through the base plate of the tool Tighten securely to 41 N m 30 Ib ft NOTICE After machining the cylinder block inspect for the presence of a chamfer on the edge of the balcony Use a hand stone to break the sharp edge if needed 10 Raise the tapered cutter head from the block and install the depth set spacer provided While there is no load extend the cutting tool outward using a clockwise rotation of the cutting screw until it just touches a 0 15mm feeler gauge or shim placed next to the vertical wall of the counterbore Tighten the Allen head hold down screws 11 12 13 14 15 NOTICE Do not turn past this position or the cutter plate will fit and prevent an accurate reading Lower the cutting plate and cutter tool into the counterbore until it just touches the lower surface of the counterbore Rotate the lock collars downward until they touch the bronze bushing of the tool Set the depth of cut by adjusting the top collar upwards to allow the liner shim to be inserted between the two collars Tighten the thumb screw of the top collar Remove the shim Lubricate the tool bushing Back off the lower collar by two graduations 0 0254 mm 0 001 in each Rotate the T handle clockwise with a moderate constant2. 0 0008 it contacts the O rings Admissible Deformation of the Cylinder Liner Collar at the Contact Surface with the Seat Insert Mee 002 Mons Admissible Deformation of the Cylinder Liner Collar Seat at the Contact Surface with the Seat Insert Max 009100012 Table 2 Cylinder Liner Inspection Tolerances 1 4 1 3 MEASUREMENT OF CYLINDER LINER PROTRUSION Measurement steps are as follows 1 Clean the contact surfaces of the cylinder block the cylinder liner and the measuring plate NOTE Correct cylinder liner protrusion is necessary to obtain a perfect seal when the head gasket is compressed by the cylinder head 2 Install the liner and shim into the block without the seals J 46180 1 Cylinder Head Bolts Figure 5 Measuring Plate 3 Install the measuring plate J 46180 on the cylinder block and cylinder liner Fasten the measuring plate to the block by inserting the cylinder head bolts into the spacers and then threading them into the holes in the cylinder block 4 Tighten the cylinder head bolts to 50 N m 37 lb ft 3 Feeler 1 Dial Gauge 2 Slot 4 qty Figure 6 Dial Gauge 5 Install the dial gauge so that the feeler on the dial gauge extends into the slot in the measuring plate The feeler must touch the contact surface of the cylinder block with some preload Support the dial gauge 1 Collar Seat Insert shim 4 Liner Seat D Ring 2 Cylinde
3. 7 7 Remove the bolts spacers and measuring plate as installed 1 4 2 CYLINDER BLOCK PREPARATION This procedure is used with the PT 2250 B counterbore tool and J 41065 1 Collar Seat Insert shim 4 Liner Seat D Ring 2 Cylinder Block A Specified in Measuring Cylinder Liner Protrusion Table 3 Cylinder Liner Figure 8 Cylinder Liner Collar Seat 1 2 Remove the cylinder heads pistons liners and other hardware Protect the crankshaft oil and coolant passages from machining debris by covering with a shop towel or a suitable clean cover Clean the top surface of the block to remove any debris from the machining area Remove the cylinder block dowel pins using Snap On CG503 or equivalent Remove the coolant pump refer to section Removal of Coolant Pump and the rear lifting bracket Protect internal engine parts from cutting debris using an oiled sponge filler in the cylinder block 6 The cutting edge of the cutting bit should be retracted to protect the cutting tool Cap screws of the cutter should be loose at this time 1 Cylinder Block 2 Cutter Plate 48323 Figure 9 Cross Section 7 Center the tool on the top of the block using the Counter Bore Cutter tool J 41065 8 Raise the depth stop adjustment collars and lower the tapered cutter plate into the bore Rotate the tool and allow it to center itself in the bore PT 2250 B d010034 1
4. DETROIT DIESEL MBE 4000 Service Information NUMBER 08 MBE 4000 1 REV S M REF 1 4 ENGINE EPA07 MBE 4000 DATE February 2008 SUBJECT CYLINDER BLOCK LINER SERVICE PROCEDURE PUBLICATION DDC SVC MAN 0026 6SE420 Amended tool number J 46180 New procedure describes the steps needed to service the engine with the installation of the new design liner with the D ring seal 1 4 1 REMOVAL OF CYLINDER LINER Removal steps are as follows 1 Cylinder Block 2 Cylinder Liner Figure 1 Mark the Cylinder Liner 1 Remove the piston Refer to section Removal of Piston 2 Using a paint pen mark the position of the cylinder liner in the cylinder block Mark both the cylinder liner and the block Then make another set of marks 90 degrees from the first set in a clockwise direction NOTE If the same cylinder liner is used again it must be installed at an offset of 90 degrees from its last position This reference will not be needed if the cylinder liner is being replaced NOTICE To prevent cylinder liner damage never use a hammer or other unsuitable device to remove the cylinder liner 1 Lower Nut 3 Upper Nut 2 Resting Bridge Figure 2 Cylinder Liner Removal Tool J 45876 3 Remove the cylinder liner using the cylinder liner removal tool J 45876 a Clean and wipe out the inside of the cylinder liner of any oil or coolant b Install the cylinder liner removal tool
5. in the cylinder liner to be removed with bridge resting on deck of cylinder block and lip of tool resting on the top of the cylinder liner c Tighten the lower nut to expand the tool in the cylinder liner d Tighten the upper nut on the tool until the cylinder liner is pulled from the cylinder block Remove the cylinder liner and tool e Remove the tool from the cylinder liner 1 Collar Seat Insert shim 4 Liner Seat D Ring 2 Cylinder Block A Specified in Measuring Cylinder Liner Protrusion Table 3 Cylinder Liner Figure 3 Cylinder Liner Seat 4 Remove the shim from the block counterbore N ENNY S RENN SY pA LIL Dm DELL Zs Sp EZ CS RQQ NGM DMS SSS ar 1 Collar Seat Insert shim 5 Upper O ring 2 Block 6 Lower O ring 3 Cylinder Liner A Specified in Measuring Cylinder Liner Protrusion Table 4 Liner D Ring Figure 4 Cylinder Liner O rings 5 Remove and discard the two O rings from the block 6 Clean the cylinder block sealing areas and inspect for corrosion 7 Check the condition of the cylinder liner collar seat Ensure that the depth of the collar seat is within the specifications listed in Table 1 0 230 0 330 0 0090 0 0130 Table 1 Cylinder Liner Installation Tolerances 8 Looking for rust or corrosion check the condition of the cylinder liner collar seat listed in Table 2 Admissible Out of Round of the Cylinder Liner where Max 0 02
6. linder liner protrusion from the block The specifications are listed in Table 4 Cylinder Liner Protrusion From Block see Figure 3 Ref A 0 230 0 330 0 0090 0 0130 Height of the Cylinder Liner Collar see Figure 3 10 10 10 12 0 3976 0 3984 Depth of the Collar Seat see Figure 3 9 950 10 010 0 3917 0 3941 Thickness of the Seat Insert 0 14 0 16 0 0055 0 0063 Table 4 Cylinder Liner Installation Tolerances 1 Cylinder Liner 3 Dial Gauge 2 Quick Calipers 4 Cylinder Block Figure 14 Measuring the Cylinder Liner Inside Diameter 9 Measure the inside diameter of the cylinder liner and check for out of round a Measure at three different locations 60 degrees apart in the area of the two O rings b Compare the three measurements If they differ by more than the maximum admissible out of round listed in Table 2 remove the cylinder liner and inspect the two O rings and their seating area in the cylinder block c If the O rings are damaged replace them d Check the out of round again until it meets specifications 10 Install the piston Refer to section Installation of Piston ADDITIONAL SERVICE INFORMATION Additional service information is available in the Detroit Diesel EPAO7 MBE 4000 Service Manual DDC SVC MAN 0026 6SE420 The next revision to this manual will include the revised information DETROIT DIESEL Qj CORPORATION te 13400 Outer Drive West Detroit Michigan 48239 4001 Telepho
7. m where it contacts the O rings up to the bevelled area 6 When installing a new cylinder liner make sure that the diameter tolerance code corresponds to the one marked on the piston For tolerance codes location refer to the edge of the cylinder liner a Cylinder liners with tolerance code A require a piston of code BA b Cylinder liners with tolerance code B require a piston of either code BA or BC c Cylinder liners with tolerance code C require a piston of code BC 1 Installation Nut 3 Cylinder Block 2 Cylinder Liner Figure 13 Cylinder Liner 7 Install the cylinder liner using the cylinder liner installation tool J 46168 NOTICE Do not overtighten the installation tool This may deform the cylinder liner and make the installation tool more difficult to remove a Tighten the installation tool just enough to hold the installation tool inside the cylinder liner without turning NOTICE To prevent damage to the O rings the cylinder liner must be rotated during installation If installing the old cylinder liner offset the reference marks 90 degrees from the previous ones NOTE b Insert the cylinder liner into the cylinder block until it contacts the O rings Continue to insert the cylinder liner past the O rings being careful to keep turning the installation tool until the cylinder liner is properly seated c Remove the installation tool from the cylinder liner 8 Measure the cy
8. ne 313 592 5000 www detroitdiesel com Detroit Diesel DDC and the spinning arrows design are registered trademarks of Detroit Diesel Corporation Copyright 2008 Detroit Diesel Corporation All rights reserved Printed in U S A
9. pressure Stop at random positions to prevent creating a ridge in the counterbore Continue backing off the adjustment in 0 0508 mm 0 002 in increments for the balance of the cutting operation until the collars come together Raise the handle and insert the spacer block under the lower collar Remove the hold down bolts and spacers to remove the tool from the block Retract the cutter bit into the cutter plate to protect during storage 1 4 3 INSTALLATION OF CYLINDER LINER Installation steps are as follows 1 Perform the Measurement of Cylinder Liner Protrusion procedure refer to section Measurement of Cylinder Liner Protrusion 2 Install new O rings clean and dry in the cylinder block 1 Collar Seat Insert shim 4 Liner Seat D Ring 2 Cylinder Block A Specified in Measuring Cylinder Liner Protrusion Table 3 Cylinder Liner Figure 11 Cylinder Liner Seat 3 Install Liner Seat D Ring to Cylinder Liner Be sure the D ring is installed with the flat surface of the of the ring against the liner Be careful not to over stretch the ring as it is installed over the liner flange NOTE The cylinder liner collar and collar seat must remain completely free of oil ARROW TOLERANCE CODE LOCATION 1 Piston 2 Cylinder Liner Figure 12 Tolerance Codes 4 Install a new seat insert clean and dry into the block counterbore 5 Apply a light coating of engine oil to the lower part of the cylinder liner fro
10. r Block A Specified in Measuring Cylinder Liner Protrusion Table 3 Cylinder Liner Figure 7 Measuring Protrusion 6 Measure the cylinder liner protrusion from the block in four places once at each slot in the measuring plate The acceptance rejection criteria is listed in Table 3 Cylinder Liner Protrusion From Block 0 230 0 330 0 0090 0 0130 Difference Between the Four Measuring Points Max 0 02 0 0007 Table 3 Specifications for Measuring Cylinder Liner Protrusion a Set the scale on the dial gauge to zero b Move the dial gauge until the feeler touches the cylinder liner collar Record the reading on the dial gauge c Move the dial gauge and support to the next slot and repeat the measurement process until four measurements have been made one at each slot Record each measurement d Check each measurement If any one measurement records protrusion of less than 0 230 mm 0 0090 in or more than 0 330 mm 0 0130 in remove the cylinder liner and check it according to the procedures that refer to section Removal of Cylinder Liner NOTE There are three different cylinder liner shim thicknesses that are available 0 15 mm 0 30 mm and 0 50 mm e Compare the four measurements If any measurement differs from any one of the others by more than 0 02 mm 0 0008 in replace the cylinder liner and repeat steps a through e If the cylinder liner measurements are within specification continue to step
Download Pdf Manuals
Related Search