installation, operating, G1, G2, G3 & G2 trifecta
Contents
1. Insert the drawer into the base assembly N PO C1 5 43254 080510 COFFEE GRINDING a DOr T Turn the selector knob to align the arrow with the desired grind Raise the top lid and add the whole bean coffee Close the top lid Locate the back of a bag behind the dispense chute or insert the brew cup The grinder will not operate unless the bag brew cup sensor is activated Allow the bag to rest on the screen beneath the chute Press the start switch Flip the cleaning lever a few times as dispensing slows Remove the bag or brew cup when ground coffee is no longer dispensed from the chute The grinder will stop automatically as the bag or brew cup is removed NOTE The start switch will have to be pressed again to continue the cycle if the bag or brew cup is removed while grinding ADJUSTMENT 1 Place a brew cup in place or an empty bag on the screen with the back of the bag behind the dispense chute 2 Start the grinder to clear the grind chamber Leave grinder ON 3 Turn the Grind Selector knob to the TURKISH or 1 position 4 Using a small flat blade screwdriver loosen the two set screws on the left side of the grind selector knob 5 Hold the knob in the TURKISH or 1 position with one hand 6 Using a large flat blade screwdriver slowly turn the adjusting screw in the center of the grind selector knob to the right clockwise until a metallic whine can be heard due to the rub2. G1 G2 G3 amp G2 trifecta BUNN Coffee Mill INSTALLATION amp OPERATING GUIDE BUNN O MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD ILLINOIS 62708 3227 PHONE 217 529 6601 FAX 217 529 6644 www bunn com To ensure you have the latest revision of the Operating Manual or to view the Illustrated Parts Catalog Programming Manual or Service Manual please visit the Bunn O Matic website at www bunn com This is absolutely FREE and the quickest way to obtain the latest catalog and manual updates For Technical Service contact Bunn O Matic Corporation at 1 800 286 6070 43254 0000E 04 14 2010 Bunn O Matic Corporation BUNN O MATIC COMMERCIAL PRODUCT WARRANTY Bunn O Matic Corp BUNN warrants equipment manufactured by it as follows 1 Airpots thermal carafes decanters GPR servers iced tea coffee dispensers MCR MCP MCA single cup brewers ther mal servers and ThermoFresh servers mechanical and digital 1 year parts and 1 year labor 2 All other equipment 2 years parts and 1 year labor plus added warranties as specified below a Electronic circuit and or control boards parts and labor for 3 years b Compressors on refrigeration equipment 5 years parts and 1 year labor c Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis parts and labor for 4 years or 40 000 pounds of coffee whichever comes first These warranty peri
3. 3 Slip bag under the chute Rest the bag on the tray 4 Press the start switch 5 Flip the cleaning lever a few times as dispensing slows 6 Remove the bag The grinder will stop automatically 39956 0000 G1 39957 0000 G2 amp G3 43254 021712 ELECTRICAL REQUIREMENTS CAUTION The grinder must be disconnected from the power source until specified in Initial Set Up 100V amp 120V Models 230 VOLT CE Model Note This electrical service consists of 2 current carrying conductors L1 and Neutral and a separate conductor for chassis ground CE REQUIREMENTS e This appliance must be installed in locations where it can be overseen by trained personnel e For proper operation this appliance must be installed where the temperature is between 5 C to 35 C e Appliance shall not be tilted more than 1 for safe operation e An electrician must provide electrical service as specified in conformance with all local and national codes e This appliance must not be cleaned by water jet e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given instructions concerning use of this appliance by a person responsible for its safety e Children should be supervised to ensure they do not play with the appliance e f the power cord is ever damaged it must be replaced by the manufacturer or authorized se
4. detergent and hot water Reinstall the spring and rotor with burr onto the motor shaft 9 Align the slot in the motor shaft with the rotor and reinstall shear plate Reinstall rotor cup and grind selector dial plate to the burr housing Refer to the Adjustment section of the Operating and Service manual for burr adjustments PREVENTIVE MAINTENANCE Bunn O Matic Corporation recommends that preventive maintenance be performed at regular intervals Maintenance should be performed by a qualified service technician For Technical Service contact Bunn O Matic Corporation at 1 800 286 6070 NOTE Replacement parts or service caused by failure to perform required maintenance is not covered by warranty 6 Month Weekly Cleaning plus replace the dechaffer assembly 1 Year 1 On grinders with slide plates check the slide plates and clean 2 Inspect and clean replace burrs and grind chamber if necessary 3 Adjust the burrs and grind time to your specifications for particulate size and throw weight BASE RELOCATION Disconnect the grinder from the power source Tip the machine gently on its back so it rests with approximately one inch of the bottom overhanging the work surface Remove the drawer from the base assembly Place the base against the grinder bottom and align the four sets of holes Securely fasten the base to the grinder bottom using the four screws and washers provided Raise the grinder to the upright position
5. N Pour O Matic BUNN BUNN with the stylized red line BUNNlink Bunn OMatic Bunn O Matic BUNNserve BUNNSERVE with the stylized wrench design Cool Froth DBC Dr Brew stylized Dr design Dual Easy Pour EasyClear EasyGard FlavorGard Gourmet Ice Gourmet Juice High Intensity iMIX Infusion Series Intellisteam My Caf Phase Brew PowerLogic Quality Beverage Equipment Worldwide Respect Earth Respect Earth with the stylized leaf and coffee cherry design Safety Fresh savemycoffee com Scale Pro Silver Series Single Smart Funnel Smart Hopper SmartWAVE Soft Heat SplashGard The Mark of Quality in Beverage Equipment Worldwide ThermoFresh Titan trifecta TRIFECTA sylized logo Velocity Brew Air Brew Beverage Bar Creator Beverage Profit Calculator Brew better not bitter Build A Drink BUNNSource Coffee At Its Best Cyclonic Heating System Daypart Digital Brewer Control Element Milk Texturing Fusion Nothing Brews Like a BUNN Picture Prompted Cleaning Pouring Profits Signature Series Sure Tamp Tea At Its Best The Horizontal Red Line Ultra are either trademarks or registered trademarks of Bunn O Matic Corporation The commercial trifecta brewer housing configura tion is a trademark of Bunn O Matic Corporation 2 43254 031314 USER NOTICES Carefully read and follow all notices on the grinder and in this manual They were written for your protection All notices on the grinder are to be kept in good condition Repla
6. bing of the grinding burrs 7 While holding the knob in the TURKISH or 1 position back off the screw to the left counterclockwise just until the metallic whine ceases 8 Turn off the grinder 9 Push the knob against the dial plate and tighten both set screws on the left side of the grind selector knob 10 Turn the grinder on and listen again for the metallic whine with the grind selector knob in the TURKISH or 1 position If the metallic whine is heard repeat steps 7 through 10 until the sound ceases 11 If no metallic whine is heard the grinding burrs are adjusted properly On trifecta models you should hear a Slight chirp of the burrs contacting if you rotate the knob fully clockwise past the 1 position 6 43254 051710
7. cations to this warranty or to make additional warranties that are binding on BUNN Accordingly statements by such individuals whether oral or written do not constitute warranties and should not be relied upon If BUNN determines in its sole discretion that the equipment does not conform to the warranty BUNN at its exclusive op tion while the equipment is under warranty shall either 1 provide at no charge replacement parts and or labor during the applicable parts and labor warranty periods specified above to repair the defective components provided that this repair is done by a BUNN Authorized Service Representative or 2 shall replace the equipment or refund the purchase price for the equipment THE BUYER S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT WHETHER DERIVED FROM WARRANTY OR OTHERWISE SHALL BE LIMITED AT BUNN S SOLE OPTION AS SPECIFIED HEREIN TO REPAIR REPLACEMENT OR REFUND In no event shall BUNN be liable for any other damage or loss including but not limited to lost profits lost sales loss of use of equipment claims of Buyer s customers cost of capital cost of down time cost of substitute equipment facilities or services or any other special incidental or consequential damages 392 A Partner You Can Count On Air Infusion AutoPOD AXIOM BrewLOGIC BrewMETER Brew Better Not Bitter Brew WISE BrewWIZARD BUNN Espress BUNN Family Gourmet BUNN Gourmet BUN
8. ce any unreadable or damaged labels SPECIAL 11075 0000 11075 0100 11075 0004 SPECIAL G2 trifecta a AWARNING Sy Use only on a properly protected circuit capable of the rated load To reduce the risk of electric shock Electrically ground the chassis conan VPMOXE OT OREN COVE 00824 0002 Follow national ocal electrical codes No user serviceable parts inside Do not use near combustibles Authorized service personnel only Disconnect power before servicing An extension cord when used must be shorter than 20 feet if 16 gage 3 conductor wire or shorter than 10 feet if 18 gage 3 conductor wire FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE FIRE OR SHOCK HAZARD READ THE ENTIRE OPERATING MANUAL INCLUDING THE LIMIT OF WARRANTY AND OFF STOP 37881 0000 PLEASE CLOSE LID BEFORE GRINDING LIABILITY BEFORE BUYING OR USING THIS PRODUCT A PERSONALINJURY HAZARD Keep Fingers amp Foreign Objects CAUTION out of Hopper or Chute Opening 20545 0000 PLEASE DO NOT POUR GROUND 11076 0000 BUNN Coffee Mill 1 Select the desired grind 2 Lift the lid and pour coffee beans into the hopper 3 Slip bag under the chute Rest the bag on the tray 4 Press the start switch 5 Flip the cleaning lever a few times as dispensing slows 6 Remove the bag The grinder will stop automatically BUNN Coffee Mill 1 Select the desired grind 2 Lift the lid and pour coffee beans into the hopper
9. ods run from the date of installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period This warranty does not apply to any equipment component or part that was not manufactured by BUNN or that in BUNN s judgment has been affected by misuse neglect alteration improper installation or operation improper maintenance or repair non periodic cleaning and descaling equipment failures related to poor water quality damage or casualty In addition the warranty does not apply to replacement of items subject to normal use including but not limited to user replaceable parts such as seals and gaskets This warranty is conditioned on the Buyer 1 giving BUNN prompt notice of any claim to be made under this warranty by telephone at 217 529 6601 or by writing to Post Office Box 3227 Springfield Illinois 62708 3227 2 if requested by BUNN shipping the defective equipment prepaid to an authorized BUNN service location and 3 receiving prior authorization from BUNN that the defective equipment is under warranty THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY WRITTEN OR ORAL EX PRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE The agents dealers or employees of BUNN are not authorized to make modifi
10. panel or grind chamber housing parts 1 Clean all exterior surfaces using a damp cloth rinsed in any mild nonabrasive liquid detergent Care should be taken not to scratch the grinder with any abrasive material 2 Empty all beans from hopper s Plug in the grinder place an empty bag behind the dispense chute or trifecta brew cup Press and release the START switch Run a few cycles until all coffee in the grind chamber is dispensed and disconnect the grinder from the power source Remove the bag or brew cup WARNING Prior to cleaning the grind chamber unplug the grinder 3 Remove the two screws and remove the dial plate and selector knob assembly 4 Slide the burr auger rotor spring assembly off the motor shaft and disassemble for cleaning 5 Remove the two screws securing the stationary burr to the grind chamber 6 Remove the four screws at the top of the chute and remove the chute Using a pair of pliers remove the C clips securing the flapper arm to the chute Remove the flapper securing pins carefully noting the location of each flapper spring 7 Wash all parts in a mild solution of detergent with hot water and a stiff non metallic bristle brush Rinse all parts thoroughly and allow them to air dry before reinstalling 8 Carefully clean the grind chamber dial plate assembly chute opening and dial plate opening with a dry stiff non metallic bristle brush Wipe with a clean cloth that has been soaking in a mild solution of
11. rvice personnel with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard e Machine must not be immersed for cleaning e Machine rated IXP1 INITIAL SET UP CAUTION Unplug the grinder throughout the initial set up 1 Open the top lid Clear all foreign objects and shipping materials from the hopper compartment and the entrance to the grind chamber 2 Install filler plate 3 The grinder can now be plugged in and put into service OPERATING CONTROLS Grind Selector Allows the user to vary the grind for each coffee Each setting will provide precisely the same grind every time it is selected Off On Start Switch OFF STOP upper position Switching to this position stops the operation of the grinder ON center resting position The switch will return to this position after a grind cycle has begun and will remain in this position after grinding has ceased START lower momentary position Pressing the switch initiates grinding only when a bag is in place behind the chute or the brew cup is in place Bag Brew Cup Sensor Prevents the grinder from operating unless the back of a bag is in place behind the dispense chute or the brew cup is not in place Do not attempt to bypass this safety device Cleaning Lever Allows the operator to clean out any coffee residue left from the previous grind 4 43254 042414 CLEANING WARNING Unplug the grinder before the removal of any
Download Pdf Manuals
Related Search