thermal arraycorder service manual wr300-um-251
Contents
1. 5V P P Oo Mo o 5V P P 10 Hz Sine wave 20mV P P 9 Press the START STOP key to start measurement Wait until the data capture is finished 10 Press the START STOP key to stop measurement 11 Press the REPLAY key to output the waveform Confirm that the waveform shown below appears WR300 UM 251 9370 3 13 3 DISASSEMBLY AND REASSEMBLY 12 Check the waveform channel by channel using the procedure described in step 10 13 Press the MEMORY key twice to change the Replay View Settings in the Data Replay setting menu Replau View Settings Ree lay CH CH Selection Ratio 14 Press the ENTER key at the channel setting to display the channel setting menu 15 Turn on only the channels which need to be checked 16 Press the EXE key to confirm 17 Press the REPLAY key to display the waveform then check it 18 Repeat the above steps 10 to 16 for all channels for which amplifiers are mounted 19 When the HDD check has been completed delete the data which is stored on the HDD using the following procedure 20 Press the SYSTEM key to display the System Settings menu then select Disk Initialize Press the ENTER key to display the following window System Settings System 1 4 Settings Save current settings Load settings from disk Return to detault settings Disk Operation File List File Copu File Rename File Delete Disk Initialize2. H ZL OL H LL VIONOd HOOL OL H26 HD9OLHOS Gauvod 16 CONTROL MOTHER BOARD Trey OL quvogd INdNI 21901 AJM Q21 OMWOS SIMI MEE s H Z OL DCIDC LHSIT MOVa 000 IAG SV INYS 000 ING SV dINVS 000 ING SV ANVS INVHSOVIG 342018 00 4M 7 1 WR300 UM 251 9370 7 BLOCK DIAGRAMS 7 2 CABLE WIRING 7 2 1 Cable Wiring for 8 16 ch Models Av 138 021 0 00 4M 91001 91907 80 00 4M E Z 016HO 60 00 HM 7 0064 93 P L 00 4M 93 A N A Y0 00 4M 23 L0 00 4M 1 00 4M VO ecd kd c8d t8d td JL ed Odvod QVO8 8 10A1NO9 70 005 90 0005 sl Odvod NIYIN 90 00 4M VO 01 00 4M VO YAMOd W31SAS 90 00 4M LO0AF90VV adl 31901 31901 801 GHO 10 00 4M 94 an SOLON 80 00 4M VO 60 00 iM VO YOSNSS bd YOSNAS gv o JLNo 20 2 Y9 LJOW8 9 12 1 UPIM uu 002 AaLlNIAd IVNAJAHL ENS K HO 9L SL dV E S HO PL EL 3 O HO ZL LL E HO 01 6 3 HO 8 2 za HO 9 S 3 HO F
3. ARRAYCORDER WR300 UM 251 SERVICE MANUAL WR300 UM 251 02 9370 GRAPHTEC HISTORY OF REVISIONS No 1 Date issued 04 09 27 06 03 29 06 03 29 06 03 29 N WR300 UM 251 9370 ENSURE SAFETY This Service Manual has been compiled for the purpose of facilitating repair and maintenance of the WR300 Series Thermal Arraycorders by Graphtec service personnel and other persons who have undergone equivalent technical training Maintenance or repair by unauthorized service personnel is to be strictly avoided Because the WR300 contains numerous internal components with a high electric potential such work by unauthorized service personnel could cause human injury or serious damage to the recorder WR300 UM 251 9370 li 5 1 CONFIGURATION 1 1 Model Configuration 1 1 1 2 m 1 1 1 3 Accessories and Options en ea bs 1 1 2 UPGRADING THE FIRMWARE 2 1 How to Upgrade the WR300 Flash ROM from the TCP IP port 2 1 2 2 How to Upgrade the WR300 Flash ROM from the PCMCIA Card 2 7 3 DISASSEMBLY AND REASSEMBLY 3 1 Notes on Disassembly and Reassembly 3 1
4. 58 ayyog 3 H Z L dV OMYOS JOMINOO 70 0054 90 0005 90 90 9NINIM 318V9 OOSUM 7 3 WR300 UM 251 9370
5. CS EM ES ES L3 EI oe ee me mm s key Test Press all the keus to exit RANGE POSI AUTO copy CURSOR G urst ST FEED now exec START STOP 4 Press the START STOP key to start the test for the keys Confirm the response of all the keys This test will close when you have pressed all the keys WR300 UM 251 9370 9 32 6 PARTS LISTS 6 PARTS LISTS 6 1 RECOMMENDED PARTS LISTS 790131700 Main Control Board tf 790131702 AMP Mother Board 1 770131131 System PowerBoard 1 790131701 Control Key Board J 41 J z 16 ch Control Board 1 Onlyfor 16 ch WR3x0 16 models Fan Motor cuu n 11 VoltageAmp 2 222 WR MAMP 1 Temperature Amp o 1 jFrequenyAmp 0 0 WR3 DCB AMP LOGICAMP 1 LogicAmp 0 500052364 500052367 500052365 KPC 108 8TA01 STA 500002329 770530103 770530104 500051411 790530705 500051647 790530706 790530707 x 2 0 WR300 UM 251 9370 6 1 6 PARTS LISTS 6 2 Parts Lists 6 2 1 Front A Rear Cover Parts PartNo Description CE QTY Remarks 1 601310100 Front Cover 1 20 2 601310110 Rear Cover L 1 02 3 076005030 Handle Pate 1 4 076005040 Handle Bottom Plate 2 5 601100290 Handle Cover 2 7 0 6 076005030 Hande
6. 13 Turn off the WR3xO This completes the setup of the DCB type amp s WR300 UM 251 9370 4 10 4 SETUP PROCEDURES 4 5 Setting Up the F V Type Amp This procedure is required when any part of the F V amp is replaced Preparation As shown below use a signal generator Wiring connection WR3x0 Signal generator generator LS Note Mutually connect the ground terminals of the signal generator and the WR3x0 Setup procedure 1 Connect a signal generator which generates exactly 40 kHz to the F V amp input terminal 2 Leave the WR3x0 turned on for at least 30 minutes 3 Set the measurement mode to RECORDER mode 4 After entering the System Setup mode open the Setup menu as shown below Specify the measurement conditions as shown below Setup CH Ch01 16 or Ch01 08 or Ch01 04 Setup AMP type FV Select FV Setue CH CHO1 16 AMP tupe MA Mode Setupll Basic Press Exec key to setup mode WR300 UM 251 9370 4 11 4 SETUP PROCEDURES 5 Press the EXECUTE key Message 6 The GND Start to start message is displayed at the location shown above 7 Input 5 V 0 Hz _ L to the input terminals of all the channels 8 Press the START STOP key and then wait until the 40KHz Start to start message appears 9 Input 5 V 40 KHz T L to the input terminals of all the channels Note If each displayed frequency is within 34 kHz to 38 kHz
7. 4 After entering the System Setup mode open the Setup menu as shown below Specify the measurement conditions as shown below Setup CH Ch01 16 or Ch01 08 or Ch01 04 Setup AMP type M Mode Setup1 Ch01 16 Setup CH AMP tupe WR300 UM 251 9370 4 3 4 SETUP PROCEDURES 5 Press the EXECUTE key Message 6 The GND Start exec message is displayed at the location shown above 7 Input 0 000 to the input terminals of all the channels 8 Press the START STOP key and then wait until the 20 mV Start exec message appears Specify the voltage generator s output voltage setting to correspond to one of the displayed voltage ranges in the following table and then input that voltage to the WR3x0 Input Voltage 20 000 mV 50 000 mV Note If each displayed voltage is within 6096 to 8096 then the amp is OK But if the voltage differs greatly the amp needs to be repaired After repairing the amp this setup procedure must be performed again 9 Repeat step 8 by sequentially setting the Measure parameter to 20 mV 50 mV 100 mV 200 mV 500 mV and 1 V and then inputting the corresponding voltage 10 When you have finished the Setup operation for 1 V the EEPROM Exec to start message appears Press the EXECUTE key to begin writing the new Setup data to the EEPROM of each amp 11 After the setup parameters have been registered to the EEPROM the display closes
8. 909090 4 Input cable Connect both ends to GND Setup procedure 1 As shown in the figure above connect the output of the voltage generator to the WR3x0 s amp input terminal 2 Leave the WR3x0 turned on for at least 30 minutes 3 Set the measurement mode to RECORDER mode 4 After entering the System Setup mode open the Setup menu as shown below Specify the measurement conditions as shown below Setup CH Ch01 16 or Ch01 08 or Ch01 04 Setup AMP type V CH01 16 or CH01 08 or CH01 04 WR300 UM 251 9370 4 4 SETUP PROCEDURES 5 Press the EXECUTE key bcm wo NN mm _ Message 6 The GND Start exec message is displayed at the location shown above 7 Input 0 000 to the input terminals of all the channels 8 Press the START STOP key and then wait until the 50 mV Start exec message appears Specify the voltage generator s output voltage setting to correspond to one of the displayed voltage ranges in the following table and then input that voltage to the WR3x0 Note If each displayed voltage is within 70 to 90 then the amp is OK But if the voltage differs greatly the amp needs to be repaired After repairing the amp this setup procedure must be performed again 9 Repeat step 8 by sequentially setting the Measure parameter to 50 mV 100 mV 200 mV 500 mV 1V 2 V and 5 V and then inputting the corresponding volta
9. Disk Initialize Initialize mode Drive Format iive Type Quick Volume Label Press Enter to select Exec to start format operation 21 Set the drive to C HDD 22 Set the type to Quick 23 Press the EXE key to start the formatting operation WR300 UM 251 9370 3 14 3 DISASSEMBLY AND REASSEMBLY 3 8 Replacing the Printer Assembly 200 mm width printer Disassembly 1 Detach the bottom cover assembly see Section 3 3 2 Detach the rear cover see Section 3 4 3 Detach the front cover see Section 3 5 4 Detach the control panel assembly see Section 3 6 5 Remove the two M3L4 binding head screws holding the printer assembly from the top Printer assembly M3L4 binding head screw 6 Remove the three M3L4 binding head screws holding the printer assembly from the front side plate Front side plate M3L4 binding head screw WR300 UM 251 9370 3 15 3 DISASSEMBLY AND REASSEMBLY 7 Remove the three M3L4 binding head screws holding the printer assembly from the rear side plate Rear side plate M3L4 binding head screw 8 Disconnect all the cables from the system power board then detach the printer assembly Sensor Connector I ET k 5 WR300 UM 251 9370 3 16 3 DISASSEMBLY AND REASSEMBLY Re assembly 1 To attach the printer assembly perform the above Disassembly procedure in reverse WR300 UM 251 9370 3 17 3 DISASSEMBLY AND
10. Setting Procedure 1 Press the MENU key to display the AMP setting window as shown below and then make the following settings AMP V M DCB or F V select the measuring amp Input DC Range Select the range to be measured Filter V M DCB amp set to Line F V amp set to Off Input DC Range Select the range to be measured Settings LH Input Range Filter Misc DE line line Line Line Line Line gt sie s Ze s a Filter V M DCB amp set to Line F V amp set to Off WR300 UM 251 9370 0 2 5 INSPECTION AND CHECK PROCEDURES 2 Press the DOWN POSITION key to display the Memory Settings menu shown below and then make the following settings RANGE CI EB L3 Capture Destination Memory Sampling Interval 1 us Block Size 8 KW x 128 Memor Settings Common Settings Capture Destination same ling Interval Time Scale 200us D1 Program Block Disable Data Memory Settings Block Size Capture Time Memory Chain Stab Calc Number of Means 3 Press the DOWN POSITION key to display the Trigger Settings window as shown below and then make the following settings RANGE OSITION Function Memory Action Single Start Condition Source Off Stop Condition Source Off Trigger Settings Common Settings Memory Time Gate Disable Set ima Action St
11. 3 Press the DOWN POSITION key until the Format Settings window as shown below appears then make the following settings RANGE GroupA Zone 1 GroupB Zone 2 Group Zone 3 Group 4 4 C and D are for the 16 channel model only Menu Index Settings Memory Settings Format Settings Trigger Settings Grid 10 Fine Record Settings Envelope Replay Settings Priority Display Priority CH EU Settings zone Settings Annotation Settings Zone Preset Preset 1 Calculation CH Zone Color Width Trace System Settings 00 200 mm m dot On dot On Customize Settings dot On System Information dot Or dot On dot On dot On dot On CO fon PF co to 2 0 200 3 0 200 mm 4 Q 200 mm a 0 200 mm 6 0 200 mm 7 mm 8 gt POSITION Menu Up Menu Down WR300 UM 251 9370 5 29 5 INSPECTION AND CHECK PROCEDURES Points to check 1 Set the threshold level to 1 4 V TTL Input the signal to the logic amp Check the level of the signal 2 Set the threshold level to 2 5 V TTL Input the signal to the logic amp Check the level of the signal 3 Set the threshold level to 5 0 V TTL Input the signal to the logic amp Check the level of the signal High level Low level WR300 UM 251 9370 5 30 5 INSPECTION AND CHECK PROCEDURES 5 8
12. Replay Settings 5 ji z 9 The following Max Min values window is displayed Confirm that the values are within the ratings Cal cul ation OS DO 447 0 437 0 634 0 625 k Press CANCEL 1 key to close Note Press the Mode key to change the measurement range t 43 X EU ca WR300 UM 251 9370 5 9 5 INSPECTION AND CHECK PROCEDURES Measurement procedure for the F V amp 1 Input the reference signal for each range according to the table below and then check that the level of measurement is within the rating F V amp Signal precision ratings Input Frequency Rating 0 4 of F S 200 Hz 100 0 Hz 0 8 Hz 200 0 Hz 400 Hz 400 Hz 1 Short the terminals if you cannot input 0 Hz Function generator output AMPTD 10 V p p rectangular wave TL 2 Press the START STOP key and then wait until the Finished message is displayed 3 Press the START STOP key to stop measurement 4 Press the REPLAY key to display the waveform 5 Press the CURSOR key twice to display the two cursors Note Two cursors are displayed 6 Press the MENU key 7 Press the DOWN POSITION key until the Calculation Settings window as shown below appears and then make the following settings RANGE OSITION me EB EB mm Ma ZA Function Max Min 1 Press the ENTER key Calculation Settings Calculation Statistical Ca
13. then the amp is OK But if the voltage differs greatly the amp needs to be repaired After repairing the amp this setup procedure must be performed again 10 Press the START STOP key and then wait until the EEPROM Exec to start message appears Press the EXECUTE key to begin writing the new Setup data to the EEPROM of each amp 11 After the setup parameters have been registered to the EEPROM the display closes and returns to normal mode 12 Turn off the WR3x0 This completes the setup of the F V type amp s WR300 UM 251 9370 4 12 4 SETUP PROCEDURES 4 6 Setting Up the Printer Head Resistance for the Printer This procedure is required when the printer is replaced Preparation for the 200 mm Width Printer 1 Getthe printer head resistance value of the printer from the label on the option printer unit as shown below 2 For example the label shown above has a marking R 1244 so the printer head resistance value will be 1201 1290 Ohm Preparation for the 100 mm Width Printer 1 The 100 mm width printer use a fixed value for the printer head resistance value so the printer head resistance value is 680 740 Ohm WR300 UM 251 9370 4 13 Setup procedure 4 SETUP PROCEDURES 1 Press the MENU key to display the Menu Index menu shown below RANGE POSITION Settings Memoru Settinas 15 Settings Record Settings Replay Settings Format Settings Sri Tas A
14. 1 C A J j WR300 UM 251 9370 6 2 6 PARTS LISTS 6 2 2 Front amp Rear Side Plate Parts PartNo Description QTY Remarks 1 601310000 Front Side Plate _ 1 S 2 601310110 AMP Guide Plate 20 gt 3 601310010 Rear Side Plate 1 o 6 770131101 Fan Assembly 2 L ee DO4R 24TM EX 770131102 AC Power Input Assembly Inlet IG 0642S 690130040 Cable CA WR300 04 NN q 7 7 WR300 UM 251 9370 6 3 6 PARTS LISTS 6 2 3 AMP Slot Chassis Parts Rear view Top view 601310030 AMP Slot Chassis Top 601310050 AMP Slot Chassis Bottom RAM 1 601310040 Slot Chassis Center 1 e US 6 2 4 Power Supply Chassis Parts 601310030 Power Supply Chassis LT 601310050 16 Ch Control Board Holding Rubber Only for 16 Ch model WR300 UM 251 9370 6 4 6 PARTS LISTS 6 2 5 Mother Board Parts AMP slot assembly WR300 02 6 2 6 Power Supply Parts Main unit assembly Remarks __ 500052367 Power Supply Board BFE24SX U 3 Washer M3C3 1 4 Flatheadscrew 103 Ach 3 8 ch 16 ch 1 WR300 UM 251 9370 6 5 6 5 LISTS 6 2 Left Side Parts PartNo Description Remarks OT 601510150 ket Side Cover 1 WR30 __ 601310140 IRIG Left Side Cover 1 6 601310150 IRIG Switch Bracket 1 WR310 6
15. 2 8 Logic Input Parts PartNo Description 1 601310180 16 ch Logic Input Cover 1 601310170 8 ch Logic Input Cover 1 J 601310160 4 ch Logic Input Cover 1 2 WR300 UM 251 9370 6 6 6 PARTS LISTS 6 2 10 System Power Board Parts Main unit assembly 770131131 System Power Board q qp T 690130060 Cable CA WR300 06 EL 690130510 Flexible Cable FC WR300 01 1 WR300 UM 251 9370 6 7 6 5 LISTS 6 2 11 Main Control Board Parts 790131700 Main Control Board PCMCIA Card Slot Mechanical Part 500052369 IC11SA BD PEJR 14 WR300 UM 251 9370 6 8 6 PARTS LISTS 6 2 11 HDD Parts 2 607308300 HDD Bracket 20000 6 2 12 16 ch Control Board Parts a No 1 46CH Control Board For 16CH unit WR300 UM 251 9370 6 9 6 PARTS LISTS 6 2 13 Control Panel Parts Cut this part for 4 ch No PartNo Description Remarks 1 601310300 ControlPanelCover 1 2 601310353 4 chlabel x 1 _ 601310363 B chlabel 10 _ 601310373 16 chlabel 10 3 500051411 LED AA084VC01 0 0 0 1 20 4 1601310310 1 j 5 790131701 Control Panel Board 6 690130130 Cable CA WR30013 7 770131118 LCD Relay Board PR WR300 05 1 gt 8 601310340 LCD Relay Board Ins
16. Block Size 128 KW x8 Memory Settings Common Settings Capture Destination Same ling Interval 1Ous 100kHz Time Scale 2 00ms DIV Program Black Disable Data Memory Settings 1 Block Size Capture lime Memory Chain stat Cale Number of Means WR300 UM 251 9370 9 15 5 INSPECTION AND CHECK PROCEDURES 3 Press the DOWN POSITION key to display the Trigger Settings window as shown below and then make the following settings RANGE Function Memory Action Single Start Condition Source Off Stop Condition Source Off Trigger Settings Common Settings Pulveli ele Memory Time Gate Disable See mee Action Smee Start Condition ounce Internal Settings Pre triqger Stop Condition ounce Time Settings 4 Press the DOWN POSITION key to display the Record Settings window as shown below and then make the following settings RANGE OSITION Function Direct Waveform Display Mode Scroll Record Settings Record Settings Function Direct Chart Speed 25mm s v1 Setting 11 0mm s v 2 Setting 100 mm min Waveform Display Mode Scroll Channel ID OFF Print Record Settings scale Print ist Print Scroll WR300 UM 251 9370 5 16 5 INSPECTION AND CHECK PROCEDURES 5 Press the DOWN POSITION key to display the Data Replay Settings window as shown below and then make the following settings RANGE CI EN ES Rep
17. Checking the Control Panel Keys 1 Press the MENU key to display the Menu Index menu shown below RANGE POSITION CLOSE m Ho e 000000 O0 oa Menu Index Sustem Information Amp Settings Memory Settings FPGA Trigger Settings System Control Record Settings Memory Control Replay Settings Trigger Control Format Settings 16Ch Control El Settings Print Control Annotation Settings Firmware Calculation Main CPU Firmware Ver Sustem eke BE Operation System Ver Weise Settings Printer CPU Firmware Yer Customize Settings Network System Information MAC Address DU US vb 00 JU CD CH System Information Ane Settings Annotation Settings Firmware Calculation Main CPU Firmware Ver 10 Sustem Settings Operation Sustem Ven 11 Option Settings Printer CPU Firmware _ Ver 12 Customize Settings Network 13 System Information Address 1 2 Memory Settings So rigger Settings System Control Yer 1 A Record Settings Memor Control Ven 1 Replay Settings Trigger Control Ven B Format Settings 15Ch Control 15 fa Sol Print Control 2 8 9 00 03 6 00 00 00 WR300 UM 251 9370 5 31 5 INSPECTION AND CHECK PROCEDURES 3 Press the DOWN DIRECTION key ten times to display the Key Test menu shown below RANGE POSITION
18. Ohm 4 Select the Printer Head Resistance and then press the ENTER key 5 Turn off the WR3x0 WR300 UM 251 9370 4 15 5 INSPECTION AND CHECK PROCEDURES 5 INSPECTION AND CHECK PROCEDURES 5 1 Insulation Resistance Use a megohm meter an insulation resistance gauge to check that the insulation resistance between the following terminals are equal to or higher than the rated values Measuring terminals Rated value Remarks V amp SIG to FG Megohm meter with an All channels output capacity of 500 VDC insulation resistance ida ERE is 100 M ohm or more AC inlet AC Line to FG Megohm meter with an Line input output capacity of 500 rf resistance of 20 M ohm or more WR300 UM 251 9370 5 1 5 INSPECTION AND CHECK PROCEDURES 5 2 Inspection and Check Methods 5 2 1 Measurement Accuracy Supply the reference voltage or frequency determined for each measurement range to each installed amp and then check the voltage or frequency accuracy Preparation Use a voltage generator for the V M and DCB amps that can output up to 500 VDC using four digit settings Use a signal generator for the F V amp that can output rectangular waveforms 0 0 Hz to 50 kHz frequency 10 Vp p AMPTD e Mutually connect the ground terminals of the voltage generator and the WR3x0 prior to initiating measurement Wiring Connection Same wiring connection as the V M DCB or F V amp setup See setup procedure
19. dV 3 H Z L dV Vd Ld c0 00 iM gt lt U lt O I m gt JU O 8 d zad td Edi Odvod HO9L 20 0054 3 Z MOSL HD91 8 en n XSrz34g ayog AlddNS H3MOd g N y0 00 YM V9 0 00 HMA VO UMOJg Z0 00 UM VO enig E 10 004M VO 34O N enig 197 HOLIMS HAMOd ONIMIM 318V9 HO9L 8 00 4M 7 2 WR300 UM 251 9370 7 BLOCK DIAGRAMS ch Model 7 2 2 Cable Wiring for 4 90 00 4M VO S0 00 4M VO MOOL HOV OdVOd YAMOd NALSAS N XSyzadd 90 00 iM kd ayog AlddNS H3MOd AIddnS YSMOd Av 138 0 00 4M v LO0AF80VV q21 10 00 4M 03 10 00 4M VO 80 00 4M e 60 00 HM YOLOW 0 00 4M V9 UMOJg Beo 25 55 YOSNIS H3A029 200280 Yo Od m OOCUMOA 5 L0 00c4M VO YOSNAS 339494 D 33J4O N 1 9 0 VLS LOVL8 80 L OdM Upim 001 il I e amp alNied IVNAJAHL enig NE 1 4 3 HOLIMS H3MOd 8 U E S N u NO n co v U ae GHVOd BN L0 00 34M 39 gt 5 5 r U a sR 28 m Do Ej N U U gt N 2 0 v HH Les eae S Hove
20. data replay settings as shown below tt 2 2 Replay Source Settings Source Disk File Name C A DEFAULT GOT Data Save Conditions Sampling Interval Time Scale No of Data Replay View Settings Replay CH CH Selection Output Ratio 5 Press the INPUT key then set the following 502 25Vto 25V In the case of a DCB amplifier the input voltage is different than for other types of amplifiers Therefore you need to check each DCB amplifier individually 6 Press the RECORD key then set the trigger settings as shown below Common settings Function Memory Time Gate Disable Start Condition Source Internal Pre trigger Off Stop Condition Source Internal Trigger Settings Recordi 3 3 Common Settings Function Time Gate Bcorsnm Start Condition counce Internal Settings Pre trigger Stop Condition Source Interna Internal Settings v WR300 UM 251 9370 3 12 3 DISASSEMBLY AND REASSEMBLY 7 Make the Start Condition settings as shown below Start Condition settings Combination Edge OR CH Level 0 Up H start Condition Settings Combination Edge DB CH Mode lower ere tippar m fH Enter select Exec register This setting condition is required only for the amplifiers for which the input is set to DC 8 Setthe output of the signal generator as shown below Generator
21. from the main control board 12 Detach the main control board from the AMP mother board gt In the case of a 16 channel model Remove the three spacers BSB 307 In the case of a 4 channel model or an 8 channel model Remove the three M3L4 binding head screws M3L4 binding head screw In the case of the WR300 model Remove the four M3L4 binding head screws Main control board In the case of the WR310 model Remove the two spacers BSB 307 In the case of the WR300 model Remove the two M3L4 binding head screws Re assembly 1 To attach the main control board perform the above Disassembly procedure in reverse WR300 UM 251 9370 3 19 3 DISASSEMBLY AND REASSEMBLY 3 12 Replacing the PCMCIA Card Slot Mechanical Part Disassembly 1 Detach the main control board see Section 3 12 2 Remove the two M2L2 binding head screws holding the PCMCIA card slot mechanical part M2L2 binding head screw 3 Release the notches using by small flat head screwdriver which is holding the PCMCIA card slot of the mechanical part Release the notches which are holding the PCMCIA card slot of the mechanical part WR300 UM 251 9370 3 20 3 DISASSEMBLY AND REASSEMBLY 4 Detach the PCMCIA card slot mechanical part as shown below from the main control board Re assembly 1 To attach the PCMCIA card slot mechanical part perform the above Di
22. head screw Re assembly 1 To attach the rear cover perform the above Disassembly procedure in reverse WR300 UM 251 9370 3 4 3 DISASSEMBLY AND REASSEMBLY 3 5 Replacing the Front Cover Disassembly 1 Remove the two M3L4 binding head screws holding the front cover M3L4 binding head screw Front Cover 2 Remove the two M3L6 flat head screws holding the front cover then remove the front cover Front Cover M3L6 flat head screw Re assembly 1 To attach the front cover perform the above Disassembly procedure in reverse WR300 UM 251 9370 3 5 3 DISASSEMBLY AND REASSEMBLY 3 6 Replacing the Control Panel Assembly Disassembly 1 Detach the bottom cover assembly see Section 3 3 2 Detach the rear cover see Section 3 4 3 Detach the front cover see Section 3 5 4 Disconnect the flexible cables from the main control board Disconnect these flexible cables from the main control board Main control board Control panel assembly 5 Remove the two M3L4 binding head screws holding the control panel assembly from the rear side plate Control panel assembly Rear side plate M3L4 binding head screw WR300 UM 251 9370 3 6 3 DISASSEMBLY AND REASSEMBLY 6 Remove the two M3L4 binding head screws holding the control panel assembly from the front side plate Control panel assembly Front side plate M3L4 binding head screw 7 Detach the control panel assembly from the main u
23. 0 00 V 0 000 V 200 V 200 00 V 0 4 V 200 00 V WR300 UM 251 9370 5 5 5 INSPECTION AND CHECK PROCEDURES Voltage precision ratings Input voltage Rating 0 2 of F S 20 mV 0 04 mV 50 mV 0 1 mV 100 mV 0 2 mV 200 mV 0 4 mV 500 mV 1 mV 2V 0 004 V 200 V 0 4 V 2 Press the START STOP key and then wait until the Finished message is displayed 3 Press the START STOP key to stop measurement 4 Press the REPLAY key to display the waveform 5 Press the CURSOR key twice to display the two cursors Note Two cursors are displayed WR300 UM 251 9370 5 6 5 INSPECTION AND CHECK PROCEDURES 6 Press the MENU key 7 Press the DOWN POSITION key until the Calculation Settings window as shown below appears and then make the following settings RANGE OSITION Function Max Min 1 Press the ENTER key Calculation Settings Caleul ation Statistical Calculation 8 Select Execute and then press the ENTER key to start calculation Select Execute here and then press the ENTER key Calculation Settings Ame Settings Calculation Memory Settinas statistical Calculation xecute Sede MEE Arithmetical Calculation Record Settings FFT Caleulation E gt Format Settings El Annotation Settings Calculation J CRINE 11 Uption Settings 13 System Information 1 2
24. 16 or Ch01 08 or Ch01 04 Setup AMP type M Mode Setup2 Ch01 16 or CH01 08 or CH01 04 setup CH CHOl 1b type Mode Press Exec key to setup mite Setup2 WR300 UM 251 9370 4 5 4 SETUP PROCEDURES 5 Press the EXECUTE key Message 6 The rTemp Start exec message is displayed at the location shown above 7 Press the START STOP key and then wait until the EEPROM Exec to start message appears 8 Press the EXECUTE key to begin writing the new Setup data to the EEPROM of each amp 9 After the setup parameters have been registered to the the display closes and returns to normal mode 10 Turn off the WR3x0 This completes the setup of the M type amp s WR300 UM 251 9370 4 6 4 SETUP PROCEDURES 4 3 Setting Up the V Voltage Input Type Amp This procedure is required when any part of the V amp is replaced Preparation Have a voltage generator on hand that can output voltage up to 5 VDC four digit output e Mutually connect the ground terminals of the voltage generator and the WR3x0 Wiring connection WR3x0 QM HY alo v EY OV oM DA s EO je Z le O at O Q V AY Voltage generator SNOVJO L J FG
25. 3 2 Installing or Removing an 3 1 3 3 Replacing the Bottom Cover Assembly 3 3 3 4 Replacing the Rear Cover 3 4 3 5 Replacing the Front k l uu uyu 3 5 3 6 Replacing the Control Panel Assembly 3 6 3 7 Replacing the HDD Unit Assembly 10 3 8 3 8 Replacing the Printer Assembly 200 mm width printer 3 15 3 9 Replacing the 16 channel Control Board 3 18 3 10 Replacing the Main Control Board 3 19 3 12 Replacing the PCMCIA Card Slot Mechanical 3 20 4 SETUP PROCEDURES 4 1 Entering the System Setup menu 4 1 4 2 Setting Up the M Multi Input Type 4 3 ddr Sep iO os E 4 3 4 2 2 Se
26. 370 4 1 4 SETUP PROCEDURES 3 Press the UP DIRECTION key ten times to display the Setup menu shown below RANGE POSITION Press Exec key to setup mode 4 In this menu you can select the Setup channel the Setup AMP and the Setup Mode WR300 UM 251 9370 4 2 4 SETUP PROCEDURES 4 2 Setting Up the M Multi Input Type Amp This procedure is required when any part of the M amp is replaced Perform Setup 1 and Setup 2 in this procedure 4 2 1 Setup 1 Voltage Preparation Have a voltage generator on hand that can output voltage up to 1 VDC four digit output e Mutually connect the ground terminals of the voltage generator and the WR3x0 Wiring connection WR3x0 Qe Qe AL dl vacs L Rani 5 3VA 1 3VACrms Range o eje Rew Mejo Roje Que 33VACrms ped 33VACrms Parol 33VACrms ed 33VACrms Fena A Go WU COT Multimeter OOOO O ES FG Voltage generator OOO FG N Input cable GND Connect both ends to GND Setup procedure 1 As shown in the figure above connect the output of the voltage generator and the Multimeter to the WR3x0 s amp input terminal 2 Leave the WR3x0 turned on for at least 30 minutes 3 Set the measurement mode to RECORDER mode
27. 45 01A C58 17 gt 26 077002020 Gear Motor 1 27 378209011 Belt 90MXL48 17 0 28 601902150 SSS I 29 601902140 Gear Pulley 10 02 30 601312210 Left Side Pate 1 31 601312270 Printer Top Blind Plate 1 32 6013143 Arm 0 1 33 601312440 ArmShat 1 2 34 075002200 Bobbin Holder Leti 35 380101441 Spring C 144 10202 36 601312180 Printer 5200 1 37 380101661 Spring C 166 1 J 38 380105151 Spring DC 515 7 3 39 601312130 Head Pressure Plate 200 1 40 770131118 Printer Sensor Board 1 41 601100750 Sensor Brackt 1 C 5 WR300 UM 251 9370 6 13 6 PARTS LISTS 6 2 16 100 mm Width Printer Parts Emblem Plate GRAPHTEC EFBL 60 1410 9 2 601312040 Printer Cover100 3 601312300 Printer Cover Knob 10 S 4 601312050 Printer Cover Shaft100 1 5 601312250 Printer Cover Right Side Plate 1 6 601312240 Printer Cover Left Side 1 7 601902060 StockerGuideShaft100 1 8 601902070 WriingDrum 100 10 0 9 320806010 Bush BBB F6x8x3 10x1 2 gt 10 601902130 Gear Writing Drum 1 0 11 310008420 Bearing MR84ZZMC3PS2S 2 2 13 601312020 Thermal Head Position Adjusting Plate 100 1 A4 14 601312100 Right Si
28. 8 Press the REPLAY key to display the waveform 9 Press the CURSOR key twice to display the two cursors Note Two cursors are displayed 10 Press the MENU key WR300 UM 251 9370 0 22 5 INSPECTION AND CHECK PROCEDURES 11 Press the DOWN POSITION key until the Calculation Settings window as shown below appears and then make the following settings RANGE 1 Press the ENTER key Function P P Calculation Statistical Calculation 12 Select Execute and then press the ENTER key to start calculation Select Execute here and then press the ENTER key Calculation Settings Ano Settings Calculation Memory Settings Stabistical Calculation Pere Settings Arithmetical Calculation Execute A Record Settings FFT Calculation Replay Settings Format Settings El Settinas Annotation Settings Calculation 10 System Settings 11 Uption Settings LE SPINE 13 System Information 13 The following P P values window is displayed Confirm that the values are within the ratings iji Ru mu mi mi my mE mE Press CCANCELI key to close 4 4 Note Press the Mode key to change the measurement range WR300 UM 251 9370 9 23 5 INSPECTION AND CHECK PROCEDURES Measurement procedure 1 Input the reference signal for each amp according to the table below and then check that the measured a
29. Input Change Preparation Use a signal generator Wiring Connection Connect the signal generator to the F V amp Input a rectangular waveform to the F V amp Setting Procedure 1 Press the MENU key to display the AMP Settings window as shown below and then make the following settings Range 40 kHz Filter Off AMP Settings Input 1 3 CH Input Range Filter 0 410kH Ex ge DC AOkHz OFF v Checking Procedure 1 Make the following settings Input DC Range 40 kHz Filter Off 2 Start the waveform measurement in the RECORDER mode 3 Input the reference signal for the F V amp as shown below Function generator output AMPTD x1V 20 kHz rectangular waveform TL 4 Measure the waveform in the RECORDER mode and then check that the measured value is 20 kHz 5 Input the reference signal for the F V amp as shown below Function generator output AMPTD 1 5 to 3 5 V Offset 2 5 V 20 kHz rectangular waveform FL 6 Measure the waveform in the RECORDER mode and then check that the measured value is kHz 7 Press the MENU key to display the AMP Settings window make the following settings and then check that the measured value is 20 kHz Input 0C Range 40 kHz Filter Off 8 Measure the waveform in the RECORDER mode and then check that the measured value is 20 kHz WR300 UM 251 9370 5 26 5 INSPECTION AND CHECK PROCEDURES 5 7 Checking th
30. L BLOCK DIAGRAM u u uu uuu ea uuu 7 1 7 2 CABEE WIRING uu Lu u 7 2 2221 Gable Tor et 2 7 2 2 Cable Wiring for 4 ch Model nn 7 3 WR300 UM 251 9370 iv 1 CONFIGURATION 1 CONFIGURATION 1 1 Model Configuration The model number of the WR300 Series Thermal Arraycorder varies according to the number of channels installed in the main unit as explained below WR300 4 4 channel model WR300 8 8 channel model WR300 16 16 channel model WR310 8 8 channel model with an HDD and the IRIG function WR310 16 16 channel model with an HDD and the IRIG function 1 2 Supplies Thermal paper PZ233 10 packs 200 mm width Z fold paper 40 meters pack 200 mm width Z fold paper 100 meters pack For use ea pa Ee with the long length Z fold box Head cleaner kit B 368 Cleaning fluid and sheets for cleaning the thermal print head 1 3 Accessories and Options Unitname Modelname Description Digital clamp meter 1 ch CM 111 Measures AC DC current 0 to 2000 A AC DC voltage 0 to 1000 V resistance 0 to 4 000 kQ frequency 0 to 4000 Hz and temperature 50 to 160 C Digital clamp meter 2 ch CM 114 Measures AC DC current 0 to 2000 A AC DC voltage 0 to 1000 V resistance 0 to 4 000 kQ frequency 0 to 4000 Hz and temperature 50 to 160 C Logic IC cable RIC 07 To connec
31. MWARE 4 The following menu is displayed Open File Icon Transmission Icon Communication Setting 192 168 0 1 8023 x Firmware Update Status Preparing Header Contents File not specified 5 Click the Open File icon to display the following menu TA W300 Flash ROM rewriting tool Fie Settings Help e 1 5 File Mame Not specified Open File Icon Look in 5 wraoo 1014001 430 51014002430 11004001 4030 File name 41 01001 Files of type jwR3o0 Update Files 30 Cancel 6 Select the main update file as Mxxxa001 W30 7 Click the Open Button Look in 3 vWR300 zij 1014001 4930 51014002430 11004001 4030 File name 101001 Files of type wR300 Update Files w30 Cancel I WR300 UM 251 9370 2 2 2 UPGRADING THE FIRMWARE 8 If you need to change the TCP IP settings click the transmission icon to set up the TCP IP conditions W300 Flash ROM rewriting tool File Settings Help l Transmission Icon The default setting for the WR300 is set to 192 168 0 1 If you haven t changed it use this setting Also your computer s TCP IP port setting must be set to the same segment as 192 168 0 Communication Settings Transfer F Address 15216801 te Port number 8023 Emo mj jw Fast Transfer Enable 9 Click the Start button to start upgrading when you are rea
32. OSITION key to display the Trigger Settings window as shown below and then make the following settings RANGE FILT VERNI AUTO ZERO Function Memory Action Single Start Condition Source Off Stop Condition Source Off Trigger Settings Common Settings Function Time Gate el les Action Memory Disable Single Start Condition Source Internal Settings Pre treigger LStop Condition ounce Time Settings WR300 UM 251 9370 5 21 5 INSPECTION AND CHECK PROCEDURES 4 Press the DOWN POSITION key to display the Record Settings window as shown below and then make the following settings RANGE Function Direct Waveform Display Mode Scroll Record Settings Record Settings Function Chart Speed Setting 11 0mm s v 2 Setting 100 mm min Waveform Display Mode Scrol Channel ID OFF Print Record Settings scale Print List Print Scroll 5 Press the DOWN POSITION key to display the Data Replay Settings window as shown below and then make the following settings RANGE OSITION EB ES A Replay Source Memory Output Ratio Screen Replay Source Settings 1 a EC Replay View Settings Replay CH Output Ratio Data Save v Screen 6 Press the START STOP key and then wait until the Finished message is displayed 7 Press the START STOP key to stop measurement
33. REASSEMBLY 3 9 Replacing the 16 channel Control Board Disassembly 1 Detach the bottom cover assembly see Section 3 3 2 Remove the three M3L4 binding head screws holding the 16 channel control board and then detach the 16 channel control board ata binding head screw aa z 16 channel control board Re assembly 1 To attach the 16 channel control board perform the above Disassembly procedure in reverse WR300 UM 251 9370 3 18 3 DISASSEMBLY AND REASSEMBLY 3 10 Replacing the Main Control Board Disassembly 1 Detach the bottom cover assembly see Section 3 3 2 Detach the rear cover see Section 3 4 3 Detach the front cover assembly see Section 3 5 In the case of a 16 channel model detach the 16 channel control board see Section 3 9 5 Inthe case of a 16 channel model remove the three spacers BSB 307 holding the main control board 6 In the case of an 8 channel model or a 4 channel model remove the three M3L4 binding head screws holding the main control board 7 Inthe case of the WR310 model detach the HDD unit assembly see Section 3 7 8 In the case of the WR310 model remove the four M3L4 binding head screws holding the main control board 9 Inthe case of the WR310 model remove the two spacers BSB 307 holding the main control board 10 In the case of the WR300 model remove the ten M3L4 binding head screws holding the main control board 11 Disconnect all the cables
34. Removing an Amp This section explains the procedures for installing or removing an analog amp To remove an amp perform the installation procedure in reverse Moreover when pulling out an amp be sure to grasp the amp panel to pull the amp out and off CAUTION Always turn off the recorder before installing or removing an amp Whenever handling an amp pay due attention to avoid static electricity and so on 1 Remove the amplifier slot cover retaining screws and remove the amplifier slot cover 2 Select an amp suitable for the type of measurements to be performed and insert it in the slot by aligning the amp s guide with the main unit guide WR300 UM 251 9370 3 1 3 DISASSEMBLY AND REASSEMBLY 3 Secure the amp in place by tightening the setscrews WR300 UM 251 9370 3 2 3 DISASSEMBLY AND REASSEMBLY 3 3 Replacing the Bottom Cover Assembly Disassembly 1 Remove the six M3L6 flat head screws holding the bottom cover assembly then remove the bottom cover assembly M3L6 flat head screw Re assembly 1 To attach the bottom cover assembly perform the above Disassembly procedure in reverse WR300 UM 251 9370 3 3 3 DISASSEMBLY AND REASSEMBLY 3 4 Replacing the Rear Cover Disassembly 1 Remove the two black M4L8 flat head screws holding the handle covers then remove the handle covers and the handle Black M4L8 flat head screw Handle Rear cover Handle Cover M3L6 flat
35. S 4 3 Heplau Settinas 5 T z 9 The following Max Min values window is displayed Confirm that the values are within the ratings OO D OO r ri D UO mw 3 03 D tri 2 00 55 rit OO mh 0 447 9 4 O G34 Press CANCEL key to close Note Press the Mode key to change the measurement range WR300 UM 251 9370 5 7 t i JJ DE PI park z 5 INSPECTION AND CHECK PROCEDURES Measurement procedure for the DCB amp 1 Input the reference voltage for each range according to the table below and then check that the level of measurement is within the rating DCB amp Voltage precision ratings Input voltage Rating 0 25 of F S 0 000 mV 0 01 m strain 0 500 mV 1 m strain 1 000 mV 0 500 mV 0 0035 m strain 0 01 m strain 0 006 m strain 0 0135 m strain 0 0135 m strain 0 026 m strain 0 026 m strain 0 051 m strain 0 051 m strain Note 1 Confirm that the value is within the above tolerance after performing Auto balance Note 2 Confirm that the value is within the above tolerance after subtracting the 0 position value lt Example gt 0 0 003 m strain The value is within 0 01 m and it is OK 1 1 005 m strain 1 005 m 0 003 m 1 002 m it is within 0 0035 m and it is OK Perform Auto balance before measuring 0 of each range Auto balance procedure a Input 0 000 mV 0 0005 mV to 0 0005 to the input terminals of all the cha
36. ach amp 5 Input the reference voltage signal for each range to the 0 C reference temperature device zero controller according to the table below then check that the level of measurement is within the rating 48 838 mV 1194 6 C to 1205 4 C 5 30 mV 185 1 C to 194 9 C Note If the above measurement is performed in the same measurement environment as the setup environment the measurement results must be within the above Standard WR300 UM 251 9370 5 13 5 INSPECTION AND CHECK PROCEDURES 5 3 Signal to Noise Ratio Preparation Prepare the short terminals shown below for shorting the and terminals for each channel of the target amp and then short those terminals Vamp Make a short circuit between the and terminals M amp Make a short circuit between the and terminals DCB amp Note The F V amp does not require this test WR300 UM 251 9370 5 14 5 INSPECTION AND CHECK PROCEDURES Setting Procedure 1 2 Press the MENU key to display the AMP Settings window as shown below and then make the following settings Input DC Range 50 mV Filter Off Settings Input Range Filter Misc Input DC Range 50mV Filter Off Press the DOWN POSITION key to display the Memory Settings menu shown below and then make the following settings RANGE OSITION CI KA E3 Capture Destination Memory sampling Interval 10 us
37. acters when the upgrade is complete Also the beeper will sound for 2 seconds Please Turn Off the Power I have locked up 8 Turn off the power to the WR300 when the above message is displayed 9 Copy the sub program file for the IRIG function to the PCMCIA card from the computer Do not copy the other files to this PCMCIA card 10 Insert the PCMCIA card containing the sub upgrade program for the IRIG function into the WR300 s PCMCIA card slot 11 Turn on the WR300 to automatically execute the upgrade program 12 Wait until the display shown below appears The following message will appear on the WR300 display in yellow characters when the upgrade is complete Also the beeper will sound for 2 seconds Please Turn Off the Power I have locked up 13 Turn off the power to the WR300 when the above message is displayed WR300 UM 251 9370 2 7 3 DISASSEMBLY AND REASSEMBLY 3 DISASSEMBLY AND REASSEMBLY 3 1 Notes on Disassembly and Reassembly During disassembly disconnect the cables from the specified connectors as necessary During reassembly double check to ensure that the proper cables have been correctly re connected to the pertinent connectors e Some areas of the control panel unit possess a high electrical potential so exercise caution to avoid an electrical shock e When handling the LCD shield and LCD protective plate be careful not to leave fingerprints or other marks on them 3 2 Installing or
38. and returns to normal mode 12 Turn off the WR3x0 Next perform Setup2 WR300 UM 251 9370 4 4 4 SETUP PROCEDURES 4 2 2 Setup 2 Room Temperature Compensation Preparation As shown below use T temperature compensation leads to connect the target amps to the 0 C reference temperature device Zero controller Also be sure to use T temperature compensation leads to connect the M type amps to each other Wiring connection T output side short the and terminals WR3x0 ZEE O e OOK Geo Oc 9 9 Ge e AT mad sij go AE gnil a AL sel 1 o _ e e GeO Ge GeO 90 0 6 5 MIA TANI DI TAN d ST X is 3 T input side 0 C reference temperature device T compensation lead Zero Controller CAUTION Connect each compensation copper lead to a single terminal as shown in the above diagram parallel wiring is not permitted As shown in the figure above connect the input of the zero controller to the WR3x0 s amp input terminal Leave the WR3x0 turned on for at least 30 minutes Set the measurement mode to RECORDER mode After entering the System Setup mode open the Setup menu as shown below Specify the measurement conditions as shown below Setup CH Ch01
39. art Condition source Internal Settinas Pre trigaer See Sorel line Eb bus WR300 UM 251 9370 5 3 5 INSPECTION AND CHECK PROCEDURES 4 Press the DOWN POSITION key to display the Record Settings window as shown below and then make the following settings RANGE Function Direct Waveform Display Mode Scroll Record Settings Record Settings Function Chart Speed Setting 11 0mm s v 2 Setting 100 mm min Waveform Display Mode Scrol Channel ID OFF Print Record Settings scale Print List Print Scroll 5 Press the DOWN POSITION key to display the Data Replay Settings window as shown below and then make the following settings RANGE OSITION EB ES A Replay Source Memory Output Ratio Screen Replay Source Settings 1 a EC Replay View Settings Replay CH Output Ratio Data Save v Screen WR300 UM 251 9370 5 4 5 INSPECTION AND CHECK PROCEDURES Measurement procedure for V and M amps 1 Input the reference voltage for each range according to the table below and then check that the level of measurement is within the rating V Voltage precision ratings 50 mV 0 1 mV 100 mV 0 2 mV 200 mV 0 4 mV 500 mV 1 mV 0 002 V er ee 2 000 V 2 000 V 0 004 V 0 000 V 5 00 V 0 01 V 5 00 V 10 00 V 0 02 V 20 00 V 0 04 V 50 00 V 1 V 2 V 5V 100 V 10
40. arted and the initializing message appears for 2 to 3 seconds 5 After formatting is completed the display returns to the initial menu Preparations for the check operation WR300 Signal generator Connect the signal generator to the amplifier WR300 UM 251 9370 3 10 3 DISASSEMBLY AND REASSEMBLY Checking method 1 Press the MEMORY key to display the menu shown below 2 Seteach setting condition as follows Capture Destination Disk Sampling interval 1 micro second 1MHz in the case of a 16ch model 2 micro seconds 500kHz File Name CADEFAULT GDT Number of CH 8 in the case of a 16ch model 16 Capture Destination Disk Memory Settings 1 2 Common Settings Capture Destination Sampling Interval Time Scale 20D0us DIV Data Disk Settinas Fi la Mama DEFAULT GOT Sampling Interval 1us 1MHz Number ot CH Set 2us 500KHz when you have 16ch model File Name C DEFAULT GDT Number of CH 8 Set 16 when you have a 16ch model 3 If the capture destination is not set to the C drive change it at the following menu Press the ENTER key at this stage Data Pick eee File Name C NDEFAULT GDT Drive Available Folder File Name OEFAULT GDT Comment Enter to select 9 bo register Select C HDD then press the key WR300 UM 251 9370 3 11 3 DISASSEMBLY AND REASSEMBLY 4 Press the MEMORY key and then make the
41. de Plate 200 1 15 601312200 Bobbin Holder Shaft 4 16 601902200 Tension o o J1 S 17 076000620 TensionFelt 1 0 18 075002210 Bobbin Holder Right 4 1722 19 500002329 Thermal Head KJT 216 8MGF1 GR 1 2 WR300 UM 251 9370 6 14 6 PARTS LISTS 20 690130110 Cable CA WR30011 21 601312090 Head Support Shaft 100 4 22 601312230 Thermal Head Lift Arm 23 601312010 Thermal Head Lift Shaft100 1 24 601312220 Thermal Head Lift Arm Right 1 25 500002501 Motor PK245 01A C58 174 26 077002020 Gear Moor 17 J 27 378209011 Belt 90MXL48 1 0 28 601902150 Pulley 1 40 6 2 17 Other Parts 1 601319100 CD ROM User s Guide WR300 CUGO1 1 2 601319000 Packing Box 10000000 MEE 601909000 Flange Bobbin E NW j C 7 513400052 Connector FCN360C016 B GG 6 6 601310320 LCD Protective Plate NE NA WR300 UM 251 9370 6 15 7 BLOCK DIAGRAMS BLOCK DIAGRAM 71 BLOCK DIAGRAM T I3 NI HOLIMS NaMOd MOSL AvZ El oja LINN 10 1 A8 L AS Z AC C AS AZL AVZ dalNIdd NOSNSSQVSH GuvVOd Y3MOd WALSAS YOLOIN 318 soos samba snoven jem WM H991 OL NV3 1V14 x x 2q xa oq NI x x m ptu mm x B Hovi OLHDEL
42. dy to upgrade TA WRU Flash ROM rewriting tool File Settings Help Communication Settings 192 168 0 1 8023 gt Firmware Update Status Header Contents The following message will appear on the WR300 display in yellow characters when the upgrade is complete Also the beeper will sound for 2 seconds Please Off the Power I have locked up 10 Turn off the power to the WR300 when the above message is displayed 11 Turn on the power to the WR300 again WR300 UM 251 9370 2 3 2 UPGRADING THE FIRMWARE 12 Click the Open File icon to display the following menu TA WRU Flash ROM rewriting tool File Settings Help el A Open File Icon Look in WR300 1014001 430 51014002430 11004001 4030 File name S1 01A001 Files of type WR300 Update Files M30 gt Cancel 13 Select the sub update file Sxxxa001 W30 to upgrade the printer firmware 14 Click the Open Button 15 Click the Start button to start upgrading when you are ready to upgrade G VUR300 Flash ROM rewriting tool File Settings Help NA ru Update File Mame S101A001 W30 Communication Settings 192 168 0 1 8023 Firmware Update Status Press the Start button when preparations complete Header Contents GRAPHTEC ARZOO ROM The following message will appear on the WR300 display in yellow characters when the upgrade is complete Al
43. e EXECUTE key Message 6 The BAL Start to start message is displayed at the location shown above 7 Input 0 000 mV to the input terminals of all the channels Note Adjust the voltage within 0 0005 mV to 0 0005 mV using the multimeter 8 Press the START STOP key and then wait until the GND Start to start message appears 9 Press the START STOP key and then wait until the 1m strain Start to start message appears Specify the voltage generator s output voltage setting to correspond to one of the displayed voltage ranges in the following table and then input that voltage to the WR3x0 Input Voltage 0 9995 to 1 0005 mV 1 999 to 2 001 mV 4 998 to 5 002 mV 9 995 to 10 005 mV 19 99 to 20 01 mV Note If each displayed voltage is within 60 to 80 then the amp is OK But if the voltage is differs greatly the amp needs to be repaired After repairing the amp this setup procedure must be performed again 10 Repeat step 9 by sequentially setting the Measure parameter to 1 m strain 2 m strain 5 m strain 10 m strain and 20 m strain and then inputting the corresponding voltage 11 When you have finished the Setup operation for 20 m strain the EEPROM Exec to start message appears Press the EXECUTE key to begin writing the new Setup data to the EEPROM of each amp 12 After the setup parameters have been registered to the EEPROM the display closes and returns to normal mode
44. e Logic Amp Preparation Use a signal generator Wiring Connection Connect the signal generator to the logic amp Input a rectangular waveform to the logic amp Setting Procedure 1 Press the MENU key to display the AMP Settings window as shown below and then make the following settings Logic Enable Menu Index AMP Settinas Input Range File Misc Memor Settings rigger Settings Record Settings Replay Settings Format Settings EU Settings Annotation Settings Calculation Sustem Settings Settings Customize Settings Sustem Information T C 6o Ho p p P ipud gt 14444 4 lt 4 POSITION Key Menu amp d Menu Down Set to Enable WR300 UM 251 9370 5 27 5 INSPECTION AND CHECK PROCEDURES 2 Set the threshold level check 1 4 V 2 5 V 5 Menu Index Settings 5 Spem Input Range Fili Memory Settings Trigger Settings Record Settings Replay Settings Format Settings Ell qt Annotation Settings Calculation Sustem Settings ption Settings Lis seji se Settings System Information KU CO cC FR PO 8 yoo c Cl u PROB OO co n Roo RE logic Enable POSITION Key Merny z Henu Down TTL 1 4 TTL Enter select Exec register WR300 UM 251 9370 5 28 5 INSPECTION AND CHECK PROCEDURES
45. ect the 0 C reference temperature device zero controller to a voltage generator that can specify output up to 1 Wiring connection Voltage generator T output side T compensation lead T input side 0 C reference temperature device Zero Controller Note The compensation leads should be connected individually Do not connect in parallel Mutually connect the ground terminals of the voltage generator and the WR3x0 Setting procedure 1 Press the MENU key to display the AMP settings window as shown below and then make the following settings AMP Settings CH AMF Input Range Fri hu s TEMP 10 EMP Tr Line Input TC T Filter Line WR300 UM 251 9370 0 12 5 INSPECTION AND CHECK PROCEDURES Measurement procedure for the M amp temperature accuracy 1 Setthe measurement conditions as described above 2 Connect the target amps to the zero controller with the T compensation leads Connect each channel individually 3 Use the voltage generator to successively input the reference voltage signal for each range to the 0 C reference temperature device zero controller according to the table below then check that the level of measurement is within the rating M amp Input voltage precision ratings Type T Input voltage Standard 0 000 mV 2 5 C to 2 5 C 4 279 mV 97 2 C to 102 7 C 9 288 mV 4 Connect K compensation leads to e
46. el Keys 5 31 WR300 UM 251 9370 lil 6 PARTS LISTS 6 1 RECOMMENDED PARTS LISTS 6 1 6 2 Par TFI Ee TEE 6 2 O 2 T FRONTS Rear GOVE ite needed ener ee ua au aa a a aa at ol Sa 6 2 6 2 2 Front amp Rear Side Plate Parts n 6 3 AMP PY A A Z uuu 6 4 O 3 oer Sup Cs SIS ats 6 4 SP OTIS rE OEE dts ab 6 5 O rl uuu ien tug cua ee pas ean nese pea onan meander bode dead dau denas 6 5 O2 Em dsl Esci Xu uumaussusumsssssasasssassyasasssasasasasanasasanssassasanawasanayan nsaapanpasaahanayasa 6 6 Doro u u uuu uu E 6 6 OZ LO abis uuu u u iud cdd tua eiui 6 62 Main Control ta tue tu tu deu tum tute E E 6 8 A E A EO 6 9 TL O EELO EE L EE E E E E E E E E E ctas 6 9 5 213 we O oja ije pane as uuu ul AEEA EAE 6 10 6 2 14 Bottom Cover 6 11 6 2 15 200 mm MOM PETO Parts sta aucem emere dene doe 6 12 6 2 16 LOO Width Printer Parts u u u u u u o re u u u aaa 6 14 A IL eam oe ent UE ROE 6 15 7 BLOCK DIAGRAM A
47. formation 1 2 4 3 Replay Settinas 5 T z 13 The following P P values window is displayed Confirm that the values are within the ratings aji ation Result ness CANCEL key to Note Press the Mode key to change the measurement range Measurement 1 Use the short terminals to short the input terminals of all the channels 2 Use the voltage generator to successively input the reference voltage signal for each range according to the table below then check that the level of measurement is within the rating Input voltage precision ratings Measurement Range 0 25 mV to 0 25 mV Note Press the SHIFT key and then press the REPLAY EXIT key to change the measurement range Before starting measurement perform Auto balance when checking the DCB AMP The checking procedure is described in Measurement Accuracy WR300 UM 251 9370 0 18 5 INSPECTION AND CHECK PROCEDURES 5 4 DC Bridge Voltage Measurement Preparation Use a multimeter using four digit settings Wiring Connection Connect the multimeter to the DCB amp input terminal as shown below Multimeter DCB AMP Measurement 1 Check that the measurement voltage is within 2 003 V to 1 977 V Manufacturing specification 2 V 0 15 WR300 UM 251 9370 5 19 5 INSPECTION AND CHECK PROCEDURES 5 5 Frequency and Filter Characteristics Preparation Have on hand an oscillator capable of the types of out
48. ge 10 When you have finished the Setup operation for 5 V the EEPROM Exec to start message appears Press the EXECUTE key to begin writing the new Setup data to the EEPROM of each amp 11 After the setup parameters have been registered to the EEPROM the display closes and returns to normal mode 12 Turn off the WR3x0 This completes the setup of the V type amp s WR300 UM 251 9370 4 8 4 SETUP PROCEDURES 4 4 Setting Up the DCB Type Amp This procedure is required when any part of the DCB amp is replaced Preparation As shown below use a multimeter and voltage generator Wiring connection Multimeter u u 8 gt 7 Voltage generator OOO Cable connection D WR3x0 Pin D Pin B and C Voltage generator Note Mutually connect the ground terminals of the voltage generator and the WR3x0 Setup procedure 1 Connect the voltage generator Low noise type YEW2553 compatible model Connect the multimeter to the voltage generator in parallel 2 Leave the WR3x0 turned on for at least 30 minutes 3 Set the measurement mode to RECORDER mode 4 After entering the System Setup mode open the Setup menu as shown below Specify the measurement conditions as shown below Setup CH Ch01 16 or Ch01 08 Setup AMP type DCB Select DCB setup tupe Mode Press Exec key to setup mode WR300 UM 251 9370 4 9 4 SETUP PROCEDURES 5 Press th
49. hen wait until the Finished message is displayed 3 Press the START STOP key to stop measurement 4 Press the REPLAY key to display the waveform 5 Press the CURSOR key twice to display the two cursors Note Two cursors are displayed 6 Press the MENU key WR300 UM 251 9370 5 24 5 INSPECTION AND CHECK PROCEDURES 7 Press the DOWN POSITION key until the Calculation Settings window as shown below appears and then make the following settings RANGE 1 Press the ENTER key Function P P Calculation Statistical Calculation 8 Select Execute and then press the ENTER key to start calculation Select Execute here and then press the ENTER key Calculation Settings Ano Settings Calculation Memory Settings Stabistical Calculation Trigger Settings Arithmetical Calculation V Execute Record Settings FFT Caleulation NES Replay Settinds Format Settings El Settinas Annotation Settings Calculation 10 System Settings 11 Uption Settings LE SPINE 13 System Information 9 The following P P values window is displayed Confirm that the values are within the ratings iji Ru mu mi mi my mE mE Press CCANCELI key to close 4 4 Note Press the Mode key to change the measurement range WR300 UM 251 9370 9 25 5 INSPECTION AND CHECK PROCEDURES 5 6 Checking the F V Amp
50. lay Source Memory Output Ratio Screen Replay Settings Replay Source Settings a Replay View Settings Replay CH Output Ratio Data Save v Screen 6 Press the START STOP key and then wait until the Finished message is displayed 7 Press the START STOP key to stop measurement 8 Press the REPLAY key to display the waveform 9 Press the CURSOR key twice to display the two cursors Note Two cursors are displayed 10 Press the MENU key 11 Press the DOWN POSITION key until the Calculation Settings window as shown below appears and then make the following settings RANGE Function 1 Press the ENTER key Calculation Settings Calculation Statistical Calculation Area Statistical Calculation Settings Function Tatas skalne 2 Select P P 3 Press the EXECUTE key WR300 UM 251 9370 5 17 5 INSPECTION AND CHECK PROCEDURES 12 Select Execute and then press the ENTER key to start calculation Select Execute here and then press the ENTER key Menu Index Calculation Settings Ane Settings Calculation Memor Settings Statistical Calculation xecute Trigger Settings Arithmetical Calculation Bm Execute Record Settings Calculation Format Settings El Siu ai ayes Annotation Settings 9 Calculation Jo SUSE RICE 11 Option Settings I Sisi sm phi iri ss 13 System In
51. lculation ILI m n Enter select Exec rdgister 000 2 Select Max Min 3 Press the EXECUTE key WR300 UM 251 9370 5 10 5 INSPECTION AND CHECK PROCEDURES 8 Select Execute and then press the ENTER key to start calculation Select Execute here and then press the ENTER key Menu Index Calculation Settings 1 Amp Settings Calculation 2 Memory Settinas Statistical Calculation Execute Ma 3 Trigger Settings Arithmetical Calculation LX Execute EM 4 Record Settings FFT Caleulation E gt 3 Replay Settinas Format Setbinas EU Settings 8 Annotation Sebbings Calculation Jo SUSE RICE 11 Option Settings a SP ir ss 13 System Information 9 The following Max Min values window is displayed Confirm that the values are within the ratings Calcul ation OO 02 D OO OOS mw 0 03 D tri 2 00 2 03 mV OO GO mM O 44 0 4387 me O 634 O B2S Press CANCEL key to clo Note Press the Mode key to change the measurement range i i ar JJ DE Fi i o ca WR300 UM 251 9370 5 11 5 INSPECTION AND CHECK PROCEDURES 5 2 2 Temperature Accuracy This inspection is only performed for M type amps Preparation Use T temperature compensation leads to connect the target amp and a 0 reference temperature device zero controller as shown below e As shown below use copper leads to conn
52. mplitude is within the rating when compared with the amplitude during reference signal input Vamp Amp settings Generator output settings AMPTD Rating Rating 5 V input ELS Hz Hz 50Hz 50Hz 50Hz 50Hz Sine 5 V 500 Hz 500 Hz 2 500 to 2 500 V 500Hz 500Hz 5 V p p wave 6096 to 80 3Vto4V Nm 5kHz 5kHz EI 50kHz kHz 200kHz 200kHz 10Hz 10Hz 70 to 11296 3 5 V to 5 6 V 60 to 80 3 Vto 4 V y amp Amp settings Generator output settings AMPTD Rating Rating 2 V input line 15H 55 to 85 1 1Vto 1 7 V a 10Hz 10Hz gt v FSD FE 1000010 2v T a T PP wave 60 to 80 1 2 V to 1 6 V Nia i 5 2 20kHz 6596 to 11296 1 3 V to 2 24 V 10Hz 6096 to 8096 1 2V to 1 6 V settings Generator output settings AMPTD Rating Rating 20 m input 15Hz Hz 10Hz Hz 10Hz Hz 20m 10 000 to 10 000 m 20 mV Sine I 100 Hz EL 100Hz 60 to 80 12 m to 16 m strain strain 300 Hz Hz strain 300 Hz TE p p wave lt 1kHz kHz 20Hz 70 to 112 10 2 when the filter is off When you connect the cables to each amp in parallel the cable resistance and the input resistance of each amp will cause a decrease in amplitude 2 Press the START STOP key and t
53. nit Re assembly 1 To attach the control panel assembly perform the above Disassembly procedure in reverse WR300 UM 251 9370 3 7 3 DISASSEMBLY AND REASSEMBLY 3 7 Replacing the HDD Unit Assembly WR310 Disassembly 1 Detach the bottom cover assembly see Section 3 3 2 Remove the six M3L4 binding head screws holding the hard disk drive unit and the hard disk drive control board Main control board HDD unit assembly HDD control board 3 Detach the HDD unit assembly and the HDD control board 4 Remove the HDD unit from the HDD connecting plate on the HDD control board 5 Remove the four binding head screws holding the HDD mounting brackets then remove the HDD mounting brackets at both ends of the HDD unit WR300 UM 251 9370 3 8 3 DISASSEMBLY AND REASSEMBLY Re assembly 1 To attach the HDD unit assembly perform the above Disassembly procedure in reverse 2 Apply the filament tape on the rear side of the new HDD unit Filament tape 3 Initialize the HDD using the procedure described below WR300 UM 251 9370 3 9 3 DISASSEMBLY AND REASSEMBLY Initializing and Checking the HDD A newly installed HDD is not formatted 1 While holding down the LOCAL and EXE keys turn on the power The HDD format message appears on the display 2 The following message is displayed 3 Press the START STOP key 4 Formatting of the HDD is st
54. nnels b Press the Channel number key of the AMP for which you are going to perform auto balance 00000000 c Press the AUTO ZERO key to perform Auto balance RANGE POSITION d Wait until the Adjusting message disappears Be sure to perform Auto balance after changing the measurement range 2 Press the START STOP key and then wait until the Finished message is displayed 3 Press the START STOP key to stop measurement 4 Press the REPLAY key to display the waveform 5 Press the CURSOR key twice to display the two cursors Note Two cursors are displayed 6 Press the MENU key WR300 UM 251 9370 5 8 5 INSPECTION AND CHECK PROCEDURES 7 Press the DOWN POSITION key until the Calculation Settings window as shown below appears and then make the following settings RANGE KA E 3 Function Max Min Calculation Settings Calculation Statistical Calculation 8 Select Execute and then press the ENTER key to start calculation Select Execute here and then press the ENTER key Calculation Settings Ane Settings Calculation Memory Settings Statistical Calculation gt Settings Arithmetical Calculation Execute A Record Settings FFT Caleulation E Format Settings EU Settings Annotation Settings 9 Calculation 10 System Settings 11 Uption Settings LE SPINE 13 System Information 1 Z 3 4
55. nnotation Settings Calculation Sustem Settings metion Ett em Customize Settings Sustem Information Ane Settings Memoru Settinas rigger Settings Hecord Settinas Heplau Settinas Format Settinas EU ELE Annotation Settings Calculation Sustem Settinas Settings Customize Settings Sustem Information WR300 UM 251 9370 System Information System Control Memory Control Trigger Control 15Ch Control Print Control Firmware Main CPU Firmware Operation System Printer CPU Firmware Network Address System Information System Control Memory Control Trigger Control lech Control Print Control Firmware Main CPU Firmware Operation System Printer CPU Firmware Network Address 4 14 Vor Vor Ver 00 03 6 00 00 00 Ver Vor Ver 00 03 76 00 00 JU 4 SETUP PROCEDURES 3 Press the LEFT DIRECTION key ten times to display the Printer Head Resistance Setting menu shown below RANGE POSITION O g3 z o o oO O 200 mm width printer head Printer Head Resistance Setting Printer Head Resistance Mb Mia Mr hot Set 1020 1410 Ohm Till TO yr 1201 1290 hm 1291 1380 Ohm 100 mm width printer head Printer Head Resistance setting Printer Head Resistance seti Mi Ohm 741 800 Ohm S01 860 Ohm 61 970
56. put described below Output waveforms sine waves Frequency 1 0 Hz to 10 MHz Mutually connect the GND terminals of the oscillator and FG terminal of the WR3x0 before measurement Wiring Connection Connect the oscillator to each amp input terminal Setting Procedure 1 Press the MENU key to display the Settings window as shown below and then make the following settings AMP V M DCB F V select the measuring amp Input DC or AC depends on the input frequency Range Select the range to be measured Filter Select the filter to be measured Amp Range Span Imputsignal 2 500 to 2 500 V 5 V p p 1 0000 to 1 0000 V a DCB amp 10 000 to 10 000 m strain 20 mV Input DC or AC Range Select the range to be measured Filter Misc E 3 A E Pu Filter Select the filter to be measured 2 Press the DOWN POSITION key to display the Memory Settings menu shown below and then make WR300 UM 251 9370 5 20 5 INSPECTION AND CHECK PROCEDURES the following settings RANGE OSITION Capture Destination Memory sampling Interval 10 us Block Size 256 KW x4 Memor i I j Common Settings Capture Destination Same lina Interval Time Scale Program Block Data Memory Settinas Block Size Capture Time Memory Chain stat Cale Number of Means Memor 1Ous 100kHz 2 00ms D1 Disab e 256kW x 4 3 Press the DOWN P
57. sassembly procedure in reverse WR300 UM 251 9370 3 21 4 SETUP PROCEDURES 4 SETUP PROCEDURES The Setup menu is used to perform adjustments to various parts Perform adjustments as required for the amplifiers that you have installed 4 4 Entering the System Setup menu 1 Press the MENU key to display the Menu Index menu shown below RANGE POSITION CLOSE m Ho O O O O Menu Index System Information Ane Settings Memor Settings FPGA Trigger eu EE System Control Record Settings Memory Control Replay Settings Trigger Control Format Settings 16Ch Control EL Settings Print Control Annotation Settings Firmware Calculation Main CPU Firmware Ver lt Sustem ee Operation System Ver ption Sele tee Printer CPU Firmware Ver Customize Settings Network 1 System Information MAC Address OOP 32 re 00 00 CD CH System Information Settings Memory Settings FPGA ir leseni Settings System Control Record Settings Memory Control Replay Settings Trigger Control Format Settings 15Ch Control Print Control Annotation Settings Firmware Calculation Main CPU Firmware Ver Sele NBI Operation System Ver Settings Printer CPU Firmware Ver Customize Settings Network 1 Information MAC Address le OU OM Ln WR300 UM 251 9
58. so the beeper will sound for 2 seconds Please Off the Power I have locked up 16 Turn off the power to the WR300 when the above message is displayed WR300 UM 251 9370 2 4 2 UPGRADING THE FIRMWARE 17 Turn on the power to the WR300 again 18 Click the Open File icon to display the following menu TA WRU Flash ROM rewriting tool File Settings Help Open File Icon Look in WR300 4 Emon 430 510140020130 11004001 4030 File name 1101A001 Files of ype WR300 Update Files W30 Cancel 19 Select the sub update file Ixxxa001 W30 to upgrade the IRIG firmware 20 Click the Open Button 21 Click the Start button to start upgrading when you are ready to upgrade WR300 Flash ROM rewriting tool Seles File Settings Help Update File Mame 1101A001 W30 Communication Settings 192 168 0 1 9023 Firmware Update Status Press the Start button when preparations complete Header Contents GRAPHTEC ARZOO MAIN 1 01 AU 1 2 The following message will appear on the WR300 display in yellow characters when the upgrade is complete Also the beeper will sound for 2 seconds Please Off the Power I have locked up 22 Turn off the power to the WR300 when the above message is displayed WR300 UM 251 9370 2 5 2 UPGRADING THE FIRMWARE 23 Click the Exit icon to exit this upgrade program TA WR300 Flash ROM re
59. t RIC 08 09 with logic amp Alligator clip cable RIC 08 For use with logic amp Floating voltage input probe CM 05 Voltage fluctuation probe 02 04 Safety conversion adapter SMA 102 An adapter for converting a high voltage banana plug into a BNC plug IC clip cable RIC 09 For use with logic amp WR300 UM 251 9370 1 1 2 UPGRADING THE FIRMWARE 2 UPGRADING THE FIRMWARE The version of your WR300 s firmware can be upgraded by rewriting the flash ROM on the pertinent circuit boards using a choice of methods You can upgrade the firmware by loading the update program from either a personal computer via the TCP IP port or from a PCMCIA card 2 1 How to Upgrade the WR300 Flash ROM from the TCP IP port Preparations for the upgrade 1 Connect the AC cable for the WR300 2 Connect the LAN cable for the WR300 and the PC If you connect P to P use a cross LAN cable If you connect with a hub use a parallel LAN Cable How to upgrade OS Windows 2000 XP Software WR30upd exe lt Upgrade software file Xxx dll lt Upgrade software dll file Firmware Mxxxa001 W30 lt Main Program file for WR300 Sxxxa001 W30 lt Sub Program file for printer xxxa001 W30 lt Sub Program file for IRIG 1 Copy the upgrade software files to the same directory in the PC 2 Turn on the power switch of the WR300 3 Execute WR30upd exe F MR allup d e Ke WR300 UM 251 9370 2 1 2 UPGRADING THE FIR
60. tup 2 Room Temperature Compensation n 4 5 4 3 Setting Up the V Voltage Input Type 4 7 4 4 Setting Up the DCB Type Amp 4 9 4 5 Setting Up the F V Type Amp 4 11 4 6 Setting Up the Printer Head Resistance for the Printer 4 13 5 INSPECTION AND CHECK PROCEDURES 9 1 In lati RESISTANCE t 5 1 5 2 Inspection and Check Methods 5 2 SAM Measurement Io E E 5 2 en aestas as doe E E E 5 12 5 3 Saignal to Noise RANO uu tea 5 14 5 4 DC Bridge Voltage Measurement 5 19 5 5 Frequency and Filter Characteristics 5 20 5 6 Checking the F V Amp Input Change 5 26 5 7 Checking the Logic epe inn eil vaa nw e air wa a ia ena a c eaa wt 5 27 5 8 Checking the Control Pan
61. ulation Sheet 1 o 9 690130540 Flexible Cable FC WR300 04 1 10 690130530 Flexible Cable FC WR300 03 2 11 500051412 DC AC Inverter 5 126137 171744 12 601310330 Control Panel Chassis 1 13 601310230 4 chAMPLabel 1 02 601310240 8 ch AMP Label 1 202 601310250 16 chAMPLabel o 1 2 WR300 UM 251 9370 6 10 6 PARTS LISTS 6 2 14 Bottom Cover Parts 1 601310120 Bottom Cover 1 2 2 301120000 Tilt Stand TM 743 1 3 309100132 Foot CP 30 FF 6 S 4 601100310 Tilt Stand Holder Right 1 0 5 601100320 Tilt Stand Holder Let 10 o 6 601900150 Warning label 1 J WR300 UM 251 9370 6 11 6 PARTS LISTS 6 2 15 200 mm Width Printer Parts No Description QTY Emblem Plate GRAPHTEC EFBL 60 Printer Cover 200 10 2 ____ jEring _ J 601902200 Tension Plate 076000620 Tension Felt 075002210 Bobbin Holder Right 500002329 Thermal Head KJT 216 8MGF1 GR 601312200 Bobbin Holder Shaft 20 690130080 Cable CA WR300 08 1 WR300 UM 251 9370 6 12 6 PARTS LISTS 21 690130090 Cable WR300 09 7 22 601312230 Thermal Head Lift Arm Left 1 gt 23 601312110 Thermal Head Lift Shaft 1 gt 24 601312220 Thermal Head Lift Arm Right 1 gt 25 500002501 Motor PK2
62. writing tool Seles File Settings Help 2A WR300 UM 251 9370 2 6 2 UPGRADING THE FIRMWARE 2 2 How to Upgrade the WR300 Flash ROM from the PCMCIA Card Preparations for the upgrade Firmware Mxxxa001 W30 lt Main Program file for WR300 Sxxxa001 W30 lt Sub Program file for printer xxxa001 d30 lt Sub Program file for IRIG 1 Connect the AC cable for the WR300 2 Copy the main program file to the PCMCIA card from the computer Do not copy the sub program and other files to this PCMCIA card How to upgrade 1 Insert the PCMCIA card containing the main upgrade program into the WR300 s PCMCIA card slot 2 Turn on the WR300 to automatically execute the upgrade program 3 Wait until the display shown below appears The following message will appear on the WR300 display in yellow characters when the upgrade is complete Also the beeper will sound for 2 seconds Please Turn Off the Power I have locked up 4 Turn off the power to the WR300 when the above message is displayed 5 Copy the sub program file for the printer to the PCMCIA card from the computer Do not copy the other files to this PCMCIA card 6 Insert the PCMCIA card containing the sub upgrade program for the printer into the WR300 s PCMCIA card slot 6 Turn on the WR300 to automatically execute the upgrade program 7 Wait until the display shown below appears The following message will appear on the WR300 display in yellow char
Download Pdf Manuals
Related Search