Tek-ENTRY® Directory Worksheet
Contents
1. dn yoeg dn yoeg Sdn 05234 n 09239 OWA 021 pue OSZyd 01 joeuuoo LON OG OVA 021 01 05244 10euuoo ul aul OVA 021 JO peersur 05234 01 p109 OY 12euuo 3NOJJ 1334 0001 OL 3NOHd3131 40 OMY 22 y 22 X 2 Sif OL 193NNOO VA Og OVA 91 H3 NHOJSNVHL WALSAS ch NIN OM sit 966HI OL 2 4 1 3NI13NOHd 3018100 LANISVO M QHVOS AV T3H 966 1 AV T3H 966 13NI8VO LINN TOH INOO 006Wd weibeig uu9ls S LI ainbi4 Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved 4 1 574 Tek ENTRY No Phone Line Version Manual System Installation Programming terminals FA and to pulse open the entry door during a fire or other emergency Terminal ME is the interconnect point for multiple entrance systems Interconnect terminals ME and of all entry systems Each location must also be wired with its own transformer door strike switch contacts etc as shown on Figure 1 Sys2. 16 18 Tek ENTRY Telephone Entry System Operating Instructions 19 Copyright TekTone Sound 8 Signal M g Inc All Rights Reserved IL574 Tek ENTRYSIII No Phone Line Version Manual iii System Introduction Tek ENTRY Telephone Entry Systems are designed for easy operation and accommodate 1 750 suites The no phone line system has many sophisticated features built in such as No monthly rental bill for telephone line Call waiting with distinctive double tone e Distinctive double ring differentiates visitor calls from incoming calls e All programming is done via the system keypad EEPROM Memory retains programmed information during total power failure Two programmable relay outputs control door strikes gates cameras etc System operates with both touchtone and rotary pulse phones Door open tone for both tenant and visitor Warning tone to alert tenant that call will end in 10 seconds Automatic call termination after 8 seconds of dial tone detection e Variable tenant code length 1 2 3 or 4 digits Night service feature transfers calls to the guard or manager telephone Onekeyless entry code per tenant plus five for use by building management Built in multiple entrance capability maximum 20 Tenant codes can be actual suite numbers or coded for security purposes Dial up to five off premises telephones when connected to a telephone line
3. 00 for pulse rotary dialing or enter 11 for tone DTMF dialing Press the key to save Press the key to return to the programming menu 4 If desired press the key to end program mode gt 8 1 574 Tek ENTRY No Phone Line Version Manual Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved System Installation Programming Off Premises Dialing Up to five off premises telephone numbers can be assigned dial codes if a telephone line is connected to the PM900 Control Unit The telephone numbers are programmed in 11 digit format enter asterisks 4 for unused leading digits as follows 2555 95959 for 7 digit local calls 555 555 5555 for 10 digit local calls 1 555 555 5555 for local or long distance calls 1 When the programming menu displays OUTSIDE PHONE 1 2 3 4 or 5 press the key 2 Enter a 4 digit dial code and then the off premises telephone number Press the key to save NOTE Off premises dial codes cannot duplicate tenant dial codes 3 Press the key to return to the programming menu 4 If desired press the key to end program mode Erase Reset to Factory Default This function erases all programming including Tenant Dial Codes and Keyless Entry Codes and returns the system to factory defaults 1 When the programming menu displays ERASE RESET TO FACTORY DEFAULT press the key
4. If desired press the key to end program mode IL574 Tek ENTRY No Phone Line Version Manual 7 System Installation Programming View Keyless Entry Codes This section allows the review and or deletion of keyless entry codes 1 When the programming menu displays VIEW KEYLESS CODES press the key The message CODE TO REVIEW will appear 2 Enter the four digit keyless entry code to be reviewed The keyless entry code will be displayed 3 To delete the displayed keyless entry code press the key 4 To view all keyless entry codes use the 1 key to scroll up and the 3 key to scroll down 5 Press the key to return to the programming menu 6 If desired press the key to end program mode New Master Code The master code is used to access the program mode When the entry system is shipped from the factory its master code is set to 123 It is advisable to change the master code and record the new code in the appropriate place on the Tek ENTRY Programming Worksheet The master code is used by the installation company or by authorized personnel only when programming is necessary To change the master code 1 When the programming menu displays NEW MASTER CODE press the key The message MASTER CODE 123 will appear 2 Enter a new three digit master code and press the 4 key to save 3 Press the key to return to t
5. No Phone Line Version Manual 3 202080 ueisAs 614 7251 uoneing ot 05 asina esn 001752014 jeuruJel Y S 0 Bum yOouUOD seouejsip JeDuo 104 5 putot da lo Se sjeuiqeo 1 esf ueis s 1xeu JN 01 JN eutuue pue Ds O 0 1 e dninuu 104 EA JOOP eq snu 39NVHIN3dldlLTQN soNvuIN3 NAINN S ON E ae LAdNI WHT 3818 9 NOWWOO LOVINOO ON e Wav 3813 21 330109 4000 01141504 HOLIMS O N QuvO8 216AH L3NI8VO AV 13H 966 001 WLSOd _ LOV INOO ABVIN3WON 9 AVIBH ON Sama mewa 07 AYA LLYE SGIAOUd SIMS SN indinoWnnpemw Siamo kc 50 310N 193NNO3 za 15 4000 37815 HOOd NINIS 9G fL lt H3 HOJSNVHL ANV1HOdWI OL 31glivqWoo OWA 06 81 LON SI ALE Od 38 ISNW H3INHOJSNVHL L MIHIS 1334 0001 OL dN 37915 4004 DMV 22 XZ 2 VA 02 OVA 91 OWA 021 H3MOd WALSAS
6. Automatic Method 7 Program Keyless Entry Codes tree erecto pee enn 7 View Keyless Entry Codes ne rt HERE ERR ERR EE RR ERR 8 New 222 terreri eee rte esa 8 Door Open Time u do eoe etes aee te pte 8 Malk TINE 8 ene 8 Premises Diligenter te sod os 9 Erase Reset to Factory Default u e erue 9 P PH 9 Volume Control eee terere rene Hee datas Ee eb as deme PER Pre 9 Rotary Phone Pulse Sensitivity soncem nennen 9 Notice to U S Installers and Users o oreet o ero eee 10 Notice to Canadian Installers and Users esee 11 Illustrations Figure 1 System Wiring Diagram eter gon tte 4 Figure 2 Hands Free Panel Wiring Diagram eee 6 Figure 3 Handset Panel Wiring Diagram eee 6 Figure 4 PM900 Control Unit Mounting Template sees 12 Figure 5 Frame and Housing Installation esee 13 Figure 6 Amphenol PIN Assignment Bell Side RJ71C CA79X CA714A 14 Worksheets Programming Worksheet siose netter RE ERE ERR EE H 15 Directory Worksheets ves suis terere retten due eee dett
7. Tek ENTRY Telephone Entry System Operating Instructions A TekTone Tek ENTRY Telephone Entry System has been installed in your building to provide increased security for yourself and your family The system provides communication and entry control using your telephone Your visitor will find your name and assigned dial code number on the directory near the Tek ENTRY System When the visitor enters your dial code number the Tek ENTRY System will automatically ring your suite You can answer from any telephone Answer the call and establish the identity of your visitor The call will automatically cut off after a preprogrammed time period You will hear a tone 10 seconds before the call is disconnected If you want to allow your visitor to enter simply dial or press 9 on your telephone This will unlock the entrance to your building or complex You will hear a tone indicating the lock has been released After hearing the tone you may hang up To deny entry simply hang up Do not dial 9 If you are on the phone when a visitor calls you from the Tek ENTRY System they will get busy signal unless you have waiting service assigned to your telephone Optional Entry Code Use If the box below is filled in you have been assigned your own entry code Entering this code on the Tek ENTRY System keypad will allow you to enter the building without a key When using this code it is not necessary to pick up the
8. 9 wait for a dial tone and then dial the desired telephone number Conversation time is limited to 100 seconds NOTE Dialing an off site telephone uses requires a telephone line to be connected directly to the PM900 Control Unit Because it is used infrequently and only for short periods of time this does not need to be a dedicated telephone line it can be shared with an office phone for example The same line is also used to dial up to five off premises phone numbers from the entry panel if programmed Call Waiting If a tenant is on the telephone when called from the lobby panel or guard telephone they will hear a double tone to announce the visitor Depress the hook switch to place the outside call on hold and speak with the visitor Depress the hook switch again to switch back to the outside call 2 1 574 Tek ENTRY No Phone Line Version Manual Copyright TekTone Sound 8 Signal Mfg Inc All Rights Reserved System Installation and Programming Installation Tips 1 Make arrangements with the telephone company to install or equivalent telephone blocks one block for every 12 tenant phone lines Three 16 volt 40 VA UL Listed and CSA approved Class 2 power transformers are required one for the lobby equipment one for the electrical room equipment and one for the door strike An additional transformer is required for door strike activation This transformer should have the necessary voltage and curr
9. Special Features Postal Service Lock Provision for the installation of a postal service lock is available on the rear of the system enclosure s control panel Door Timer Cut Off Tailgate Prevention This feature requires the installation of a Normally Open switch contact that closes when the entry door has been opened A magnetic contact as used in security systems is acceptable for this application provided that it is a Normally Open type Most security door contacts are of the Normally Closed type When the electric door strike is released the door remains open for the period of time that has been programmed When the door timer cut off feature is used the door strike de energizes as soon as the system senses that the entry door has been opened This causes the door to lock when it closes regardless of the programmed time The door strike is therefore energized only as long as necessary to prevent unauthorized entry of individuals who follow behind the visitor tailgating Fire Alarm Emergency Input Connecting a Normally Open alarm contact from the building fire alarm system causes the electric door strike to pulse on and off in the event of a fire emergency situation This effectively leaves the entry door unlocked for the duration of the emergency Multiple Entrances Accommodating multiple entry doors is a built in feature of the Tek ENTRY Telephone Entry Systems Up to 20 entry systems be interconnecte
10. The message ARE YOU SURE zNO YES will appear 2 Enter to retain system programming or enter to erase all programming and return to factory defaults Press the key to return to the programming menu 4 If desired press the key to end program mode Volume Control The communication volume levels are factory preset for normal operations The levels can be increased or decreased by adjusting the potentiometers located along the bottom of the system controller behind the front display plate Audio level from the entry system to the suite is controlled by the MICROPHONE VOLUME control Audio level from the suite to the entry system is controlled by the SPEAKER VOLUME control Rotary Phone Pulse Sensitivity Telephone companies do not specify or guarantee the waveshape of the signal transmitted when the tenant dials the digit 9 from a rotary pulse telephone In order to achieve best results Tek ENTRY Telephone Entry Systems are furnished with a sensitivity adjustment potentiometer as well as an indicator lamp to view the incoming rotary signal pulses This potentiometer is labeled PULSE SENSITIVITY on the system controller The pulse sensitivity is factory preset so that a wide range of incoming rotary signals will properly trigger the door circuit and so will usually not require adjustment If adjustment 18 necessary because the door strike cannot be properly triggered use this procedure 1 S
11. frame and housing accordingly Example 1 TE905ANP 2 AM190D requires an 193 1 905 3 AM190D requires an OF OH194 1 TE905ANP 0 AM190D requires an OF OH191 Flush mounting frame shown in diagram above Frame bracket supplied with OF192 Bracket is supplied with scrulox screws but it is suggested you use the spanner type vandal resistant screws supplied with the TE905ANP Use TekTone driver HT007 Refer to Figure 4 PM900 Control Unit Mounting Template to mount the PM900 Control Unit inside the housing Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved IL574 Tek ENTRY No Phone Line Version Manual 13 Figure 6 Amphenol Assignment Bell Side RJ71C CA79X CA71A RES CO LINE RNG 2 27 RNG RNG 4 29 RNG RNG 6 31 RNG RNG 8 33 RNG RNG 10 35 RNG melt RNG 12 37 RNG RNG 14 39 RNG EIL RNG 16 41 RNG iube RNG 18 43 RNG RNG 20 45 RNG RNG 22 47 RNG RNG 24 49 RNG NGWUSEB 14 1574 No Phone Line Version Manual Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved Tek ENTRY Programming Worksheet Building Address Date of Installation Installation Company Programming Instructions A B Press the key twice to end program mode Enter and the three digit Master Code see 3 below on the keypad to access the programming m
12. handset Press the key and then the four digit number Your code will not appear on the display pec Te k on Sound amp Signal Mfg Inc
13. not exceed 100 Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved 1 574 Tek ENTRY No Phone Line Version Manual 1 1 Figure 4 900 Control Unit Mounting Template lluq L 7 THIS EDGE TO SIDE OF HOUSING THIS EDGE TO SIDE OF HOUSING 18H lluq THIS EDGE TO SIDE OF HOUSING 12 1 574 Tek ENTRY No Phone Line Version Manual Copyright TekTone Sound 8 Signal Mfg Inc All Rights Reserved Figure 5 Frame and Housing Installation OH192 Housing Frame TE905ANP Bracket Vandal Resistant bo Screws AM190D Directory SSSSSNSNWY TE Series Master Housing amp Frame Chart FRAMES FLUSH MOUNT HOUSING Wall Width Wall Height Wall Model Width Cut out Model Overall Cut out Overall Cut out Depth OF191 6 1 4 OH191 4 3 8 4 1 2 17 1 8 17 1 4 3 1 2 OF192 10 1 4 OH192 8 3 8 8 1 2 17 1 8 17 1 4 3 1 2 OF193 14 1 4 OH193 12 3 8 12 1 2 17 1 8 17 1 4 3 1 2 OF194 18 1 4 OH194 16 3 8 16 1 2 17 1 8 17 1 4 3 1 2 OF195 22 1 4 OH195 20 3 8 20 1 2 17 1 8 17 1 4 3 1 2 OF196 26 1 4 OH196 24 3 8 24 1 2 17 1 8 17 1 4 3 1 2 For more than 240 suites contact factory for frame and housing information Directories supplied separately Notes 1 Refer to frame and housing chart for wall cut out dimensions 2 AM190D directory panels have 60 name capacity For additional directories size the
14. TekTone SOUND amp C Communications for today and tomorrow Alpha Communications 42 Central Drive Farmingdale NY 11735 1202 Phone 631 777 5500 Fax 631 777 5599 Website www AlphaCommunications com Email info alphacommunications com TOLL FREE Technical 1 800 666 4800 IL574 SECTION A Rev 15 09 2010 Tek ENTRY Telephone Entry System No Phone Line Version Operation Installation and Service Manual Operation Installation and Service Manual Copyright 2002 2010 TekTone Sound amp Signal Mfg Inc All rights reserved No part of this publication may be copied without the express written permission of TekTone Sound amp Signal Mfg Inc The content of this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by TekTone Sound amp Signal Mfg Inc TekTone Sound amp Signal Mfg Inc assumes no responsibility or liability for any errors or inaccuracies that may appear in this documentation TekTone the TekTone logo Tek Call Tek Care Tek Check In Tek Com Tek Digicare Tek Door Tek Entry Tek Guard Tek Micro Tek MMARS TekNIOS TekNIOS Tek Paging Tek Phone Tek Safe Tek Select Tek Sentry Tek Sound Tek Status Tek Trio and Tek View are either registered trademarks or trademarks of TekTone Sound amp Signal Mfg Inc in the United States and or other countries All other trademarks are the prop
15. al code 0000 to relay 0 tenant dial code 0001 to relay 1 etc To automatically program the tenant dial codes to correspond to the tenant line relays 2 3 4 When the programming menu displays AUTO PROGRAM PRESS press the key The message ARE YOU SURE will appear Press the key The message PROGRAMMING PLEASE WAIT will appear The system automatically programs tenant dial codes in sequence from 0000 to 0999 a total of 1000 codes Automatic programming takes approximately 20 seconds Press the key to return to the programming menu If desired press the key to end program mode Program Keyless Entry Codes Keyless entry codes allow tenants to enter through the controlled doors using a four digit code from the system keypad rather than a key During actual use this code must be preceded by the key so that the code is not visible on the display For security assign each tenant a unique keyless entry code and do not duplicate any suite numbers or tenant dial codes 1 2 gt Copyright TekTone Sound Signal Mfg Inc All Rights Reserved When the programming menu displays PROGRAM KEYLESS CODES press the key The message KEYLESS ENTRY CODE will appear Enter a four digit code and press the 4 key to save Continue entering keyless entry codes until all are entered Press the key to return to the programming menu
16. ble in the circumstances In the case of such temporary discontinuance the telephone company shall promptly notify the customer who will be given the right to bring a complaint to the FCC if he feels the disconnection is not warranted Changes in the Telephone Company Equipment or Facilities The telephone company may make changes in its communications facilities equipment operations or procedures where such action is reasonably required and proper in its business Should any such changes render the customer s terminal equipment incompatible with the telephone company facilities the customer shall be given adequate notice to make modifications to maintain uninterrupted service General The FCC prohibits customer provided terminal equipment to be connected to party lines or to be used in conjunction with coin telephone service The Tek ENTRY Telephone Entry System is equipped with a USOC RJ11C standard miniature modular jack that is designed to plug directly into a modular jack Notification to the Telephone Company Notification to the telephone company is no longer required prior to connecting the registered equipment but upon request from the telephone company the user shall tell the telephone company which line the equipment is connected to as well as the registration number and ringer equivalence of the registered protective circuitry In most but not all areas the sum of all REN s should be 5 0 or less Malfunction of the Equipm
17. d without additional switching equipment One additional pair of wires parallel connected to terminals ME and of all entry systems is required When one entry panel is in use the other panels are temporarily disabled and display a SYSTEM IN USE message NOTE Each entry panel must be independently powered and programmed Night Service This feature redirects all entry system calls to a pre designated telephone line guard phone When this feature is enabled by entering 456 the entry system displays the Night Service On message To return to normal operation re enter 456 The pre designated telephone line must be connected to relay 0000 located on relay board 1 Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved 1 574 Tek ENTRY No Phone Line Version Manual 1 System Introduction Wiegand Data Output This feature connects Tek Entry to a card access system with a Wiegand 26 bit input When a tenant approves a visitor the tenant s code is sent to the card access system causing the door to open Guard Telephone The guard telephone must be a standard touchtone DTMF phone and is connected directly to the PM900 Control Unit via two conductors To communicate with a tenant the guard must wait for a dial tone and then enter the tenant s 4 digit relay number The guard will not receive a dial tone while the lobby panel is in use To dial an off site telephone dial
18. ed IL574 Tek ENTRY No Phone Line Version Manual 5 Q3103NNOO LON ueeus N3349 osje aM YOLOANNOO YALAWOILNALOd mat TANVd 13SQNVH LJ YOLOANNOO Q3193NNOO LON Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved weibeig weibeig joued Jospuepy e eunBiJ JGueg 4 4 6 1 574 Tek ENTRY No Phone Line Version Manual System Installation and Programming Complete the Tek ENTRY Programming Worksheet and ensure that it the Tek ENTRY Directory Worksheets and the User Operating Instructions are given to building management when installation and programming are complete Program Mode Begin End Enter and the three digit master code default is 123 to begin a programming session Use the 1 key on the keypad to scroll up the programming menu and the 3 key to scroll down When the desired function is displayed on the screen press the key to select it Follow the displayed instructions to make the necessary changes When programming is complete end program mode by pressing the 4 key twice To Program Codes Tenant Dial Codes Man
19. ent In the event that Tek ENTRY Telephone Entry System should fail to operate properly the customer shall disconnect the equipment from the telephone line to determine if it is the customer s equipment that is not working properly If the problem is with the system equipment the user shall discontinue use until it is repaired In the event service is needed the user should contact the local TekTone representative Telephone Connections Requirement Except for telephone company provided ringers all connections to the telephone network shall be made through standard plugs and standard telephone company provided jacks or equivalent in such manner as to allow for easy and immediate disconnection of the terminal equipment Standard jacks shall be arranged so that if the plug connected thereto is withdrawn no interference to the operation of the equipment at the customer s premises which remains connected to the telephone network shall occur by reason of such removal FCC Notice This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the instructions listed in this Operation Installation and Service Manual interference to radio and television reception may occur It has been tested and found to comply with the limits for a Class B Computing Device in accordance with the specifications in Subpart B of Part 15 of the FCC rules These tules are designed to provide
20. ent rating for the door strike that is to be used max 28 volts 3 amps Transformers and remote devices such as the door strike fire alarm and door contacts must be wired to the system controller located in the enclosure housing A wiring channel at the rear of the system enclosure must be provided for these devices Follow local building code requirements for low voltage wiring Ifa postal service lock is to be installed make arrangements with the local post office to supply the lock In multiple entrance applications two additional wires are required from each entry system to interconnect the system controllers see Figure 1 System Wiring Dia gram Do not mount the entry panel in an area where it may be exposed to near horizontal water or moisture sources for example driving rain or water spray Lobby Equipment Installation Refer to Figure 1 System Wiring Diagram for terminal locations Also refer to Figure 2 Hands Free Panel Wiring Diagram and Figure 3 Handset Panel Wiring Diagram 1 Copyright Sound amp Signal Mfg Inc All Rights Reserved Mount the system enclosure to the wall in the location closest to the building s controlled entry point Refer to Figure 5 Frame and Housing Installation Connect the door strike wires to terminals D1 and D2 if DC silent operation is desired or to terminals D3 and D4 for AC buzzing operation The maximum s
21. enu Press the 1 key to scroll up or press the 3 key to scroll down the menu screen to the desired function Press the key to select the desired function when it is displayed on the screen Follow the displayed instructions to make the necessary changes Factory Default Programming Function Factory Default Programmed 1 Tenant Dial Codes Blank 4 digits See Directory Worksheet 2 Keyless Entry Codes Blank 4 digits See Directory Worksheet 3 Master Code 123 4 Door Open Time 10 Seconds __ __ 0 99 sec 5 Talk Time 60 Seconds __ __ 0 99 sec 6 Night Service On Off 456 Fixed Off Premises Dialing Dial Code Telephone Number Name l _ Ed ei c 2 ___ RE CP p I See Ja S Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved IL574 Tek ENTR Y No Phone Line Version Manual 15 Tek ENTRY Directory Worksheet Dial Code Code 16 IL574 No Phone Line Version Manual Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved Tek ENTRY Directory Worksheet 1 2988 122 Dial Code Code Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved IL574 Tek ENTRY No Phone Line Version Manual 17 Tek ENTRY Directory Worksheet Dial Code Code
22. erty of their respective owners H IL574 Tek ENTR No Phone Line Version Manual Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved Table of Contents System Introdu clloh 1 General titur repre 1 Special Features i uoa VEDI OD OB edi vein p 1 LOCK 1 Door Timer Cut Off Tailgate 1 Fire Alarm Emergency Input n u nas oneee ReRe A T nnne 1 Multiple Entrances PNE 1 cR NES 1 Wiegand Data Output ertet 2 Telepliofie s en uma Saya a E REX EIE Ct ERN PSY UR 2 Call END 2 System Installation and Programming 3 Installation TIPS e dtr EU EOE RNE te IR ERR E Potro ERR UA 3 Lobby Equipment Imstall fion L tton rettet teet esae 3 Electrical Room Equipment Installation eese 5 System Programming and Settings 1 5 Program Mode Begin End tte tre ERE CHER 7 To Program Codes Tenant Dial Codes Manual Method 7 To Program Codes Tenant Dial Codes
23. et the PULSE SENSITIVITY control to the middle position 2 From the entry system call the suite telephone that is not triggering the door circuit 3 Observe the PULSE INDICATOR while the digit 9 is being dialed from the suite telephone The indicator should flash distinctly every time a pulse is heard 4 Ifthe indicator barely comes on the sensitivity is set too low Increase the sensitivity by turning the shaft of the potentiometer clockwise 1 8th of a turn at a time until the indicator shows distinct flashing 5 Iftheindicatorison steadily the sensitivity is set too high and the door circuit may false trigger Turn the shaft ofthe potentiometer counter clockwise to decrease the sensitiv ity The sensitivity may also require reduction if the phone line is particularly loud or noisy NOTE Sensitivity adjustments are notrequired when using DTMF touchtone suite telephones Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserved 1 574 Tek ENTRY No Phone Line Version Manual 9 System Installation Programming Notice to U S Installers and Users Incidence of Harm Should terminal equipment or protective circuitry cause harm to the telephone network the telephone company shall where practical notify the customer that temporary discontinuance of service may be required however where prior notices are not practical the telephone company may temporarily discontinue service if such action is deemed reasona
24. he programming menu 4 If desired press the key to end program mode Door Open Time The door open time can be reprogrammed to 0 99 seconds to prevent tailgating Factory default is 10 seconds See Door Timer Cut Off in the System Introduction Special Features section for more information 1 When the programming menu displays DOOR TIME press the key The message DOOR OPEN TIME will appear 2 Enter a two digit time in seconds and press the key to save 3 Press the key to return to the programming menu 4 If desired press the key to end program mode Talk Time Talk time can be reprogrammed to 0 99 seconds to set the maximum conversation length between a visitor and tenant Note Talk time starts when visitor dials tenant Factory default is 60 seconds 1 When the programming menu displays TALK TIME press the key The message ON LINE TIME will appear 2 Enter a two digit time in seconds and press the key to save 3 Press the key to return to the programming menu 4 If desired press the key to end program mode Pulse or Tone Dialing This section determines whether pulse or tone dialing is used to call off premises telephones Factory default is tone dialing If the outside telephone line is pulse rotary change this setting 1 When the programming menu displays PULSE OR TONE press the key 2 Enter
25. he top right corner of the 996 Relay Cabinet to the proper setting Example On IH996 relay cabinet 1 set the jumper to location 1 PlugRY912 Relay Boardsintoslots J1 J8 of the IH996 Relay Cabinet component side down with the red LED to the left Install relay boards in sequence top to bottom do not skip a slot If using more than one relay cabinet fill relay cabinets 1 through 8 in sequence Make the wiring connections as shown in Figure 1 System Wiring Diagram Plug one CT912 Connector onto each RY912 Relay Card and connect the other end to the RJ71 CA71 phone blocks NOTE Power up the system last Test the control equipment separately before connecting it to the lobby equipment test communications with the tenant connect a standard touchtone phone to the lobby or guard terminals Dial the 4 digit dial code The corresponding LED on the relay card will illuminate and communications will be established System Programming and Settings All programming of the entry system is accomplished through the use of the system keypad and the display located on the control panel Use the supplied Tek ENTRY Directory Worksheets to generate a record of the building occupants their suite numbers telephone numbers assigned dial codes and keyless entry codes These sheets will be required for programming as well as when changes are to be made Copyright TekTone Sound amp Signal Mfg Inc All Rights Reserv
26. reasonable protection against such interference in a residential installation If this equipment does cause interference to radio or television reception 10 1 574 Tek ENTRY No Phone Line Version Manual Copyright TekTone Sound 8 Signal Mfg Inc All Rights Reserved System Installation Programming which can be determined by turning off the equipment to see if the interference stops the user is encouraged to try and correct the interference by one or more of the following measures 1 Reorient the receiving antenna Relocate the Tek ENTRY Telephone Entry System with respect to the radio or television 3 Plug the Tek ENTRY Telephone Entry System into a different outlet so that the system and the radio or television are on different circuits NOTE The manufacturer is not responsible for any radio or television interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment Notice to Canadian Installers and Users Notice The Canadian Department of Communications label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of
27. tem Wiring Diagram Each location must be programmed separately At this point double check all wiring for shorts and opens Connect door strike transformer to terminals T3 and T4 The maximum door strike load that may switch through the controller is 28 volts at 3 amps 10 Connect 16 VAC from system transformer to terminals 1 and 2 on the system controller terminal block This transformer must not be used to power any other devices such as the door strike The display will illuminate and the message WELCOME DIAL CODE NUMBER will appear 11 Connect terminals and from the lobby unit to terminals and on the electrical room equipment polarity is not important Electrical Room Equipment Installation I Mount the PM900 Control Unit and the IH996 Relay Cabinet near the RJ71 CA71 phone blocks Wire connections between the cabinets can be eliminated by mounting the cabinets next to each other and using the supplied 10 conductor cable to interconnect the main controller to the relay cabinets Connect one end of the cable to JP1 on the PM900 red wire to right side and the other end to J9 on the 996 red wire to left side IH996 Relay Cabinets are used up to 8 total connect acable from J10 of the firstrelay cabinet to J9 of the nextrelay cabinet red wire to left side on both Set the relay cabinet select jumper located in t
28. the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized facility designated by the supplier Any repairs or alterations made by the user of this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment In the event service is needed the user should contact TekTone Sound amp Signal Mfg Inc 277 Industrial Park Road Franklin NC 28734 USA 828 524 9967 Caution Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Users should not attempt to make such connections themselves but should contact an appropriate electric inspection authority or electrician Load Number The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading The termination on loop may consist of any combination of devices subject only to the requirements that the sum of the Load Numbers of all of the devices does
29. ual Method Tenant dial codes are used at the entrance panel to call a tenant and are usually listed on atenants directory Suite numbers may be used as tenant dial codes if desired To manually program the tenant dial codes that correspond to the tenant line relays k gt 3 6 When the programming menu displays VIEW ENTER CODES press the key The message RELAY TO REVIEW will appear Enter 0000 to begin with the first relay The message RELAY 0000 will appear along with its corresponding tenant dial code To view all keyless entry codes use the 1 key to scroll up and the 3 key to scroll down To program the displayed relay press the 4 key and then the new 4 digit tenant dial code Press the key to save Continue in this fashion until tenant dial codes have been entered for all relays If a tenant dial code is fewer than 4 digits in length enter zeros as leading digits The leading zeros are not needed during actual use but are required during programming If an error is made when entering a tenant dial code press the key to backspace Press the key to return to the programming menu If desired press the key to end program mode To Program Codes Tenant Dial Codes Automatic Method Tenant dial codes are used at the entrance panel to call a tenant and are usually listed on a tenants directory Automatic programming assigns tenant di
30. witched door strike load is 28 volts at 3 amps An auxiliary switched device such as parking gate may be controlled through the auxiliary relay contact that is available by connecting to terminals NC normally closed common and NO normally open The maximum switched auxiliary load is 28 volts at3 amps This contact will change to the energized state for one second when the tenant dials 6 from their DTMF touchtone telephone Terminal PL is for the postal service lock Closing of a normally open switch between terminals PL and is required for activation The system is pre wired for this service but requires a lock to be installed on the rear of the system control panel optional 905 Remove the panel plug button for the postman s key and wire to the terminals Mount the lock with the supplied hardware Adjust the switch actuator for proper operation with the lock Terminal is for connection of a door timer cut off contact A normally open contact that closes when the door has been opened will cut off the door timer and instantly re lock the door This is used to prevent tailgating of unwanted visitors through the entry doors Connect between terminals TC and G Terminal FA is for connection to the building fire alarm system A normally open alarm contact that closes during an alarm condition can be connected between IL574 Tek ENTRY
Download Pdf Manuals
Related Search