Home

Inline Enrichment Device (XL-AF XiED®-14) w/AFR

image

Contents

1. Inline Enrichment Device XL AF XiED 14 w AFR Display Fits 2014 and Later Harley Davidson Sportster All Sportster with OEM 12mm Delphi 4 wire O2 sensors Protected by U S Pat No 7 805 236 other Patent Pending Made in the USA An experimental plug n play upgrade designed to let the engine equipped with OEM oxygen sensors to externally alter ECM closed loop bias value creating a variable air fuel ratio in closed loop mode approximating richer mixtures of 14 5 1 13 6 1 depending upon exhaust temperatures An improved air fuel mixture has generally shown onesof more of the following positive results e Improved Throttle Response e Lower Engine Temperature e Less Engine Surge e Decreased Exhaust Heat e Reduced Engine Ping A two LED AFR display on the XIED assists in monitoring fuel mixture by indicating 4 fuel ratio areas Normal Lean Normal Normal Rich Very Rich Richer 6 Leaner Q Installation Instructions e Locate Front Rear O2 sensors on exhaust e Sportster connectors are 8 12 from O2 sensor Two Black connectors interchangeable o Cutany tie wraps holding the connectors in place e Unplug HD weather tight connectors e Plug the XL AF XIED 14 Harness Adapter between O2 sensor and wiring harness Plug AF XIED Control unit into Harness Adapter e Make sure the connectors lock into each other e Tie wrap the control unit in place to prevent it from moving around Ground Wire BLACK Installation all
2. DO NOT WATCH the AFR lights WHILE THE BIKE IS IN MOTION Notes e Richer closed loop AFR values cannot be achieved if any exhaust leaks exist Even the smaller exhaust leak may cause less accuracy of the AF XIED or check engine lights Improper installation of slip on muffler or exhaust system upgrades may cause small leaks e AF XiED size is 2 5 L x0 9 W X 0 7 H e Settings between 14 3 4 to 13 9 8 tend to work best Because of the way that the O2 sensors AF XiED and ECM interact higher settings do not always result in the best results The settings are the approximate AFR based on an average bias values in the ECM The bias value is the centering voltage that the ECM uses to determine if it needs to make injector pulses longer or shorter based feedback It receives from the O2 sensor MEA VT NILES LAS Nightrider com Performance Products http sales nightrider com sales nightrider com Modern Engineering Old School Service S amp P MULLEN Enterprises Inc Oldsmar FL 34677 Please Note Transient codes P0131 and or P0151 may be present in the electronic control module ECM after the XIED is installed The presence of these specific codes in ECM history is not unusual on bikes with IEDs installed nor does their presence cause any problems The HD Service Manual indicates that these codes and be cleared and ignored No Check Engine light will occur Disclaimer This product is intended for race vehicles
3. atent Pending and Copyrights All Nightrider com products are made in the USA MEA VT NILES LAS Nightrider com Performance Products http sales nightrider com sales nightrider com Modern Engineering Old School Service S amp P MULLEN Enterprises Inc Oldsmar FL 34677
4. bikes e Ground wires to chassis bolt or negative battery terminal MEF VT NILES LES Nightrider com Performance Products http sales nightrider com sales nightrider com Modern Engineering Old School Service S amp P MULLEN Enterprises Inc Oldsmar FL 34677 AFR Indicator LEDs AFR Adjustment Instructions The AF XIED has an adjustable mixture control Use a Jeweler s screwdriver to make adjustments to the AF XIED Do not force the variable dial adjustment Set the initial value between 7 and 9 Maximum recommended setting is 9 Do not expose the AF XIED to high pressure water streams Making adjustments while the engine is running might cause a temporary Check Engine light This is not harmful Restarting the engine should clear the CE light if it is O2 sensor related e f you get transient Check Engine lights set the AFR approximately 1 AFR leaner e Bikes with very free flowing exhaust may perform better with slightly leaner AFR settings AFR LEDs Display Pattern Startup Green Yellow LED s will go on indicating startup sequence for 2 seconds The AF XIED will read the current mixture setting of the dial providing a blink indicator from 1 to 11 blinks indicating the target AFR Count the blinks on startup to verify the dial settings are correct Percent BIAS LAMBDA AFR Blink es Area oso m e es za conse o z ea aos os 139 el si s oso iss ol F
5. ollowing the mixture setting display the AFR LED s starts after O2 sensor warmup This usually occurs in 2 4 minutes cold and almost immediately on a warm hot bike MEA VT NILES LAS Nightrider com Performance Products http sales nightrider com sales nightrider com Modern Engineering Old School Service S amp P MULLEN Enterprises Inc Oldsmar FL 34677 Normal Running Light Patterns e Yellow under 400 mV from O2 sensor Leaner than 14 8 1 AFR e No Lights Between 400 and 750 mV from O2 sensor 14 7 14 2 1 AFR e Green over 750 mV but less than 1100 mV 14 2 13 8 1 AFR e Yellow Green over 1100 mV Richer than 13 2 1 AFR Do not read too much into the light pattern of the AFR gauge This is intended to be a general indicator of the mixture not instant reading of the fuel mixture at any pointin time Even with some smoothing it is not uncommon for the pattern to constantly change from blink yellow no lights green This is a normal cycling of the closed loop ECM The pattern should tend to stabilize more on no lights to green light You will normally only see both lights on during startup or during full throttle acceleration Normal reversion in the HD Exhaust system is enough to create yellow light lean spikes in the display pattern This is expected behavior The transition from yellow to no color and back can create the illusion that the LED s are staying solid yellow Please
6. used on closed courses and not for use on roads or vehicles otherwise subject to emisstomecontrol requirements In California this product must not be Used on any vehicle that is registered or licensed for use on public roads Actual results from the installation of the XIED may vary between individual bikes S amp P MULLEN Enterprises Inc warrants Nightrider com Performance Products against defects in factory workmanship and material for 30 days from the date of purchase with proof of purchase or until ownership in the part is transferred The manufacturer and seller make no warranties express or implied which extend beyond the description of the goods contained herein Anydescription of this product is for the purpose of identifying it and shall not be deemed to create anexpress warranty S amp P MULLEN Enterprises Inc shall not be responsible for any consequential special or incidental damages of any nature including but not limited to the loss of use of any vehicle on which the unit may be installed and the cost of obtaining substitute components Harley Davidson is a registered trademark of Harley Davidson Inc Model designation for various motorcycles is used for reference purposes only This part is not manufactured or endorsed by Harley Davidson or other motorcycle manufacturers XIED VIED and Nightridericom are registered trademarks of S amp P MULLEN Enterprises Inc Products are protected by WsS Pat No 7 805 236 other P

Download Pdf Manuals

image

Related Search

Related Contents

Imetec Acqua WP 120  ICC ICPCSG03BK networking cable  Knock Sensor  UNIVERSAL USER`S MANUAL FOR PHILCO GAS  Avaya BCM R2MFC Installation and Maintenance Manual  18頁【FDH】  Manual de usuario  

Copyright © All rights reserved.
Failed to retrieve file