35135.0000
Contents
1. INSTALLATION amp OPERATING GUIDE BUNN O MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD ILLINOIS 62708 3227 PHONE 217 529 6601 FAX 217 529 6644 www bunn com To ensure you have the latest revision of the Operating Manual or to view the Illustrated Parts Catalog Programming Manual or Service Manual please visit the Bunn O Matic website at www bunn com This is absolutely FREE and the quickest way to obtain the latest catalog and manual updates For Technical Service contact Bunn O Matic Corporation at 1 800 286 6070 ay 35135 0000J 01 13 2003 Bunn 0 Matic Corporation BUNN 0 MATIC COMMERCIAL PRODUCT WARRANTY Bunn 0 Matic Corp BUNN warrants equipment manufactured by it as follows 1 Airpots thermal carafes decanters GPR servers iced tea coffee dispensers MCP MCA pod brewers thermal servers and Thermofresh servers mechanical and digital 1 year parts and 1 year labor 2 All other equipment 2 years parts and 1 year labor plus added warranties as specified below a Electronic circuit and or control boards parts and labor for 3 years b Compressors on refrigeration equipment 5 years parts and 1 year labor c Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis parts and labor for 4 years or 40 000 pounds of coffee whichever comes first These warranty periods run from the date of2. 8 Close drain clamp insert drain plug place drain tube back into machine and replace lower access panel NOTE The dispenser must be refilled using the INITIAL FILL amp HEAT steps before reconnecting to the power source ED Ol Cora PREVENTIVE MAINTENANCE Bunn 0 Matic Corporation recommends that preventive maintenance be performed at regular intervals Maintenance should be performed by a qualified service technician For Technical Service contact Bunn O Matic Corporation at 1 800 286 6070 NOTE Replacement parts or service caused by failure to perform required maintenance is not covered by warranty ns E CCC CS frre CS 6 35135 011510 CLEANING The use of a damp cloth rinsed in any mild non abrasive liquid detergent is recommended for cleaning all sur faces on Bunn 0 Matic equipment Do NOT clean this equipment with a water jet device 2 40 gt 5 1x24h switches replace hoppers into dispenser Al 1x7d F a Wash b Rinse d Dry NOTICE NOTA yoo 07 04 2004 BUNN O MATIC CORPORATION BUNN Rinse out Whipper Chambers by placing RINSE RUN switch in the RINSE position and activating DISPENSE Turn elbow up remove Hoppers refill with product and Empty Drip Tray and wash in a solution of dish detergent a Lave b Enjuague c Sanitize c Desinfecte d Seque 1 The cleaning instructions noted above are for non dairy sugar based food product
3. HOLD BUTTON UNTIL CUP IS 2 3 FULL THEN RELEASE FMD 5 28964 0003 e e RINSE RINSE PUSH and HOLD BUTTON UNTIL CUP IS 2 3 FULL THEN RELEASE A WARNING RELEASE BUTTON WHEN CUP IS 2 3 FULL E FMD 4 28328 0008 PLACE PLACE CUP HERE CUP HERE CUP HERE CUP HERE RELEASE BUTTON WHEN CUP IS 2 3 FULL E E E E FMD 5 28328 0009 PLACE PLACE PLACE PLACE PLACE CUP HERE CUP HERE CUP HERE CUP HERE CUP HERE 35135 051111 INITIAL SET UP 1 Locate the drip tray assembly inside the dispenser door 2 Remove the drip tray and the drip tray cover and set them aside CE REQUIREMENTS e This appliance must be installed in locations where it can be overseen by trained personnel e For proper operation this appliance must be installed where the temperature is between 5 C to 35 C e Appliance shall not be tilted more than 10 for safe operation e An electrician must provide electrical service as specified in conformance with all local and national codes e This appliance must not be cleaned by water jet e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabili ties or lack of experience and knowledge unless they have been given instructions concerning use of this appliance by a person responsible for its safety e Children should be supervised to ensure they do not play with the appliance e If the power cord is ever damaged it must be replaced by the manuf
4. bottom of the dispenser 2 Turn on the water supply NOTE Water pipe connections and fixtures directly connected to a potable water supply shall be sized installed and maintained in accordance with federal state and local codes 4 35135 051111 INITIAL FILL amp HEAT CAUTION The dispenser must be disconnected from the power source throughout the initial set up except when speci fied in the instructions 1 Turn on the water supply and connect the dispenser to the power source Water will automatically flow into the tank to the proper level and then shut off This will take less than five minutes 3 When the tank is full of water open the front door and place the heater switch in the ON lower position A tank full of cold water will take approximately eighty minutes for the water to heat on 120 volt versions or forty minutes for 120 208 volt versions 120 240 volt versions and 220 240 volt versions During this waiting period complete these dispenser set up steps a Place the drip tray in front of the dispenser Set the drip tray cover in place b Place a set of keyholes in the cup locator plate over the screws beneath the hopper access door and push down gently c Fill the hoppers with the dry product to be dispensed PRESET TANK TEMPERATURE Tank temperatures have been preset at the factory to 180 F 82 C Bunn recommends that to provide the best quality beverage the installer adjust the tank temperature to
5. acturer or authorized service personnel with a special cord available from the manufacturer or its authorized service personnel in order to avoid a hazard e Machine must not be immersed for cleaning ELECTRICAL REQUIREMENTS CAUTION The dispenser must be disconnected from the power source until specified in nitial Set Up The 120 volt version of this dispenser has an attached cordset and requires 2 wire grounded service rated 120 volts ac 15 amp single phase 60 Hz The mating connector must be a NEMA 5 15R The 120 208 and the 120 240 versions of this dispenser has an attached cordset The mating connector must be a NEMA 14 20R The 220 240 volt version of this dispenser has an attached cordset Refer to the dispenser s dataplate and local national electrical codes for exact voltage requirement ELECTRICAL HOOK UP CAUTION Improper electrical installation will damage electronic components 1 An electrician must provide electrical service as specified 2 Using a voltmeter check the voltage and color coding of each conductor at the electrical source 3 Open the front door of the dispenser and place the heater switch in the OFF upper position 4 Connect the dispenser to the power source 5 If plumbing is to be hooked up later be sure the dispenser is disconnected from the power source If plumbing has been hooked up the dispenser is ready for nitial Fill amp Heat PLUMBING REQUIREMENTS This dispenser must be co
6. condition Replace any unreadable or damaged labels AWARNING As directed in the International Plumbing Code of the TN International Code Council and the Food Code Manual of the Food and Drug Administration FDA this equipment must be installed with adequate Fill water tank before turning on thermostat or connecting appliance to power source Use only on a properly protected circuit capable of the rated load Electrically ground the chassis Follow national local electrical codes backflow prevention to comply with federal state and local codes For models installed outside the U S A you must comply with the applicable Plumb 00824 0002 ing Sanitation Code for your area 00656 0001 Do not use near combustibles FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE FIRE OR SHOCK HAZARD READ THE ENTIRE OPERATING MANUAL CONTROL THERMOSTAT ADJUSTMENT BEFORE BUYING OR USING THIS PRODUCT THIS APPLIANCE IS HEATED WHENEVER To reduce the risk of electric shock CONNECTED TO A POWER SOURCE 00831 0000F 3 98 1998 BUNN O MATIC CORPORATION do not remove or open cover No user serviceable parts inside 00831 0000 200 F 190 F 180 F Authorized service personnel only APPROXIMATE THERMOSTAT TEMPERATURE SETTINGS Disconnect power before servicing 28368 0004A 08 08 2008 BUNN O MATIC CORPORATION 28368 0004 37881 0000 FMD 4 28964 0004 PUSH and
7. d until a rinse sequence has been run RUNNING A RINSE SEQUENCE 1 Place the rinse run switch in the rinse position 2 Sequentially or simultaneously at each of the positions dispense for at least 10 seconds 3 After the rinse L E D has extinguished the rinse timer is reset 4 Return the rinse run switch to the run position DISPENSER USE 1 Simply place a cup on the drip tray beneath the dispensing tip 2 Press the button and dispense the beverage 3 Release the button when the cup is approximately full and allow the whipper chamber to drain NOTE The whipper chamber must drain at the end of each dispense COLD BEVERAGE SET UP OPTIONAL Cold beverages may be dispensed from the left dispense position Simply place the HOT COLD switch near the left whipper chamber in the COLD upper position 5 35135 010413 ADJUSTMENTS The beverage solenoid is preset to dispense approximately 9 10 ounce per second This amount can be ad justed 1 Disconnect the dispenser from the power source 2 Remove the small left side access panel to adjust dispense valves 1 2 amp 3 and remove the small right side access panel to adjust dispense valves 4 amp 5 3 Rotate the control at the base of the solenoid clockwise to decrease or counterclockwise to increase the amount of water 4 Replace appropriate access panels when finished HOPPER MOTOR SPEED PROGRAMING The hopper dispense rate is preset at the factory With 22 too
8. installation BUNN warrants that the equipment manufactured by it will be commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the applicable warranty period This warranty does not apply to any equipment component or part that was not manufactured by BUNN or that in BUNN s judgment has been affected by misuse neglect alteration improper installation or operation improper maintenance or repair non periodic cleaning and descaling equipment failures related to poor water quality damage or casualty In addition the warranty does not apply to replacement of items subject to normal use including but not limited to user replaceable parts such as seals and gaskets This warranty is conditioned on the Buyer 1 giving BUNN prompt notice of any claim to be made under this warranty by telephone at 217 529 6601 or by writing to Post Office Box 3227 Springfield Illinois 62708 3227 2 if requested by BUNN shipping the defective equipment prepaid to an authorized BUNN service location and 3 receiving prior authorization from BUNN that the defective equipment is under warranty THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY WRITTEN OR ORAL EX PRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE The agents dealers or employees of BUNN are not authorized to make modifications to this warrant
9. nnected to a cold water system with operating pressure between 20 and 90 psi 138 and 620 kPa from a 1 2 or larger supply line A shut off valve should be installed in the line before the brewer Install a regulator in the line when pressure is greater than 90 psi 620 kPa to reduce it to 50 psi 345 kPa The water inlet fitting is 75 11 5 NH HOSE THREAD For convenience an elbow adaptor is provided to convert to a 1 4 flare fitting Bunn O Matic does not recommend the use of a reverse osmosis or deionized water supply to this equipment REQUIRED 1 0 gpm 3 78 Ipm flow rate from water supply line NOTE At least 18 inches of an FDA approved flexible beverage tubing such as reinforced braided polyethylene or silicone before the dispenser will facilitate movement to clean the countertop Bunn O Matic does not recommend the use of a saddle valve to install the dispenser The size and shape of the hole made in the supply line by this type of device may restrict water flow As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration FDA this equipment must be installed with adequate backflow prevention to comply with federal state and local codes For models installed outside the U S A you must comply with the applicable Plumbing Sanitation Code for your area PLUMBING HOOK UP 1 Flush the water line and securely attach it to the flare fitting on the
10. s When dispensing any other food product the cleaning cycle for the whipping chamber assembly and ejector elbow must be performed daily Las instrucciones de limpieza descritas anteriormente excluyen productos lacteos azucarados La limpieza de las camaras de mezcla y de los codos de salida de cada tolva deber realizarse diariamente Gire el codo hacia arriba remueva las tolvas llene las tolvas con Vacie la bandeja de goteo y limpiela con un detergente liquido y Para limpiar las camaras de mezcla coloque el interruptor en la posic n ENJUAGUE MARCHA RINSE RUN y pulse el boton para espumar y distribuir la bebida DISPENSE producto y coloque las tolvas nuevamente en la maquina suave no abrasivo Replace Light Bulbs as required Cambie los bombillos _ quemados cuando sea necesario 35135 051909
11. th gear and auger wire the preset dispense rate is approximately 3 to 5 grams per second With 30 tooth gear and auger wire the preset dispense rate is approxi mately 5 to 7 grams per second The hopper dispense rate can be adjusted to a range of dispense rates from approximately 1 5 to 12 grams per second as follows Place the rinse run switch in the center program position 2 Place the increase decrease switch in the desired increase or decrease position 3 Press and release the dispense switch for the chamber you wish to adjust Each time the dispense switch is pressed the rinse L E D will flash and the motor speed for that hopper will be increased decreased by approximately 2 1 2 4 Return the rinse run switch to the run position after hopper motor speed adjustments are complete DRAINING THE HOT WATER TANK CAUTION The dispenser must be disconnected from the power source throughout these steps Disconnect the dispenser from the power source Place the tank heater switch in the OFF position Shut off and disconnect the incoming water supply Remove the front lower access panel Pull out drain tube to empty into a sink or a container with a minimum of 6 1 2 gallon capacity Make sure drain clamp is closed Then remove drain plug Direct tube into sink or container and open drain clamp Continue draining tank until ALL of the water is out WARNING Be very careful with the draining water because it can be very hot
12. the powder product manufacturer s recommended temperature for the hot powder product being used LIQUID LEVEL CONTROL The system automatically maintains the hot water tank s level by energizing the refill solenoid when the water level drops below the liquid level probe If the system has not successfully refilled in 15 minutes a refill error occurs When a refill error occurs the refill solenoid is de energized and the left rinse L E D will flash about once every 5 seconds Once the cause of the refill error has been investigated see the troubleshooting guide in the Operating and Service Manual and cured the system can be reset by placing the Rinse Run switch in the programming center position momentarily RINSE TIMERS The dispenser is shipped from the factory with the rinse timers disabled To enable the rinse timers remove power from the dispenser remove the lower access panel and remove the jumper from J1 of the control boards Replace the lower access panel and return power to the dispenser When enabled the rinse timers automatically keep track of the time since the dispenser was last run through a rinse sequence If the dispenser detects that a rinse sequence has not been run for 8 hours the appropriate rinse L E D will flash continually If after an additional 4 hours 12 hours total a rinse sequence has still not been run the appropriate rinse L E D will light continuously and the appropriate hopper drives will be disable
13. y or to make additional warranties that are binding on BUNN Accordingly statements by such individuals whether oral or written do not constitute warranties and should not be relied upon If BUNN determines in its sole discretion that the equipment does not conform to the warranty BUNN at its exclusive op tion while the equipment is under warranty shall either 1 provide at no charge replacement parts and or labor during the applicable parts and labor warranty periods specified above to repair the defective components provided that this repair is done by a BUNN Authorized Service Representative or 2 shall replace the equipment or refund the purchase price for the equipment THE BUYER S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT WHETHER DERIVED FROM WARRANTY OR OTHERWISE SHALL BE LIMITED AT BUNN S SOLE OPTION AS SPECIFIED HEREIN TO REPAIR REPLACEMENT OR REFUND In no event shall BUNN be liable for any other damage or loss including but not limited to lost profits lost sales loss of use of equipment claims of Buyer s customers cost of capital cost of down time cost of substitute equipment facilities or services or any other special incidental or consequential damages 392 A Partner You Can Count On AutoPOD AXIOM BrewLOGIC BrewMETER Brew Better Not Bitter BrewWISE Brew WIZARD BUNN Espress BUNN Family Gourmet BUNN Gourmet BUNN Pour O Matic BUNN BUNN with the st
14. ylized red line BUNNlink Bunn OMatic Bunn O Matic BUNNserve BUNNSERVE with the stylized wrench design Cool Froth DBC Dr Brew stylized Dr design Dual Easy Pour EasyClear EasyGard FlavorGard Gourmet Ice Gourmet Juice High Intensity iMIX Infusion Series Intellisteam My Caf Phase Brew PowerLogic Quality Beverage Equipment Worldwide Respect Earth Respect Earth with the stylized leaf and coffee cherry design Safety Fresh savemycoffee com Scale Pro Silver Series Single Smart Funnel Smart Hopper SmartWAVE Soft Heat SplashGard The Mark of Quality in Beverage Equipment Worldwide ThermoFresh Titan trifecta Velocity Brew Air Brew Air Infusion Beverage Bar Creator Bever age Profit Calculator Brew better not bitter BUNNSource Coffee At Its Best Cyclonic Heating System Daypart Digital Brewer Control Element Nothing Brews Like a BUNN Pouring Profits Signature Series Tea At Its Best The Horizontal Red Line Ultra are either trademarks or registered trademarks of Bunn O Matic Corporation The commercial trifecta brewer housing configuration is a trademark of Bunn O Matic Corporation 2 35135 080112 INTRODUCTION This equipment dispenses hot beverages or soups on demand from powdered product It is for indoor use only on a sturdy counter or shelf USER NOTICES Carefully read and follow all notices on the equipment and in this manual They were written for your protection All notices are to be kept in good
Download Pdf Manuals
Related Search
35135.0000 35135000 cep