cannonball-blast-air..
Contents
1. 1 Place the rear cabinet near or at its final location 2 Open the rear cabinet door uncoil the power cord and feed the cord through the hole Uncoil other wiring cables Do not plug the power cord into the wall outlet at this time See figure 1 a Peel paper coating off of the frosted acrylic piece and attach to the back of the ticket plate box with black wood screws D 5 nstall the metal screens a Install the middle screen by placing it over the two threaded studs on the ball grate Secure with two nylon locknuts F You will need a 3 8 socket See figure 5 3 Move middle cabinet in front of Rear cabinet Plug in all cables between middle and front matching connectors See figure 2 4 Attach the ticket plate box to the middle cabinet using black wood screws D Plug in light cable See figure 3 b Attach the front of the screen to the ramp with two black wood screws D To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Assembly Instructions 6 Install the outer metal screens They are marked left and right Place the screens on the middle cabinet frame and push tight up again the rear cabinet See figure 6 Eug r ee d m 1 M a The grates in the bottom of the middle cabinet attach to the rear cabinet with 6black wood screw2. Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Electrical Drawing Section Important Power must be OFF to the game before removing any cable from the main board Turn OFF the power strip inside the game Em E En Li View Direction 12 Volt Jumper Cable J1 BLK RED BLK RED 12V Input TM 12v Input Ground Ground Volume Cable J2 Connector Left Audio Right Audio BLK WHT Left Audio Right Audio Ground Ground 29 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 WHT L Side Trigger Ground RED L Side Trigger Input WHT R Side Low Ticket Signal TAN Unused GRY Unused Tooth 1 Input BLU Tooth 3 Input GRN Tooth 5 Input R Side Tooth Reset Motor Sensor Input J3 Connector GRN R Side Trigger Ground BLK R Side Trigger Input GRN L Side Low Ticket Signal ORG Unused PNK Unused WHT Tooth 2 Input BRW Tooth 4 Input BLK Tooth 6 Input PUR L Side Tooth Reset Motor Sensor Input View Direction L Side Rack BRW R Side Rack L Side Motor BRW BLK BLK R Side Motor R Side Low Tkt L Side Low Tkt DBL ORG DBL WHT DBL GRY Tooth 3 Tooth 2 Tooth 1 DBL YEL DBL PUR DBL BLU Tooth 6 Tooth 5 Tooth 4 GRN GRN L Side Reset R Side Tooth The cables and connectors used in the ra
3. 21818 4 PREVENTATIVE MAINTENANCE SECTION Maintenance Chart Use the following maintenance chart as a guide only Actual maintenance intervals will depend on usage IMPORTANT Use glass cleaner and a soft clean cloth to clean all the acrylic and metal surfaces on the game Use an anti static cleaner polisher on the black ramp surface to protect it and keep it slippery and environmental conditions at the location of the game Keep a log of all inspections even if no problem exists with date and time of inspection action taken A sample Repair Record is located at the end of this manual IMPORTANT The game should be shut OFF for cleaning and maintenance Fill ticket tray Play the game to ensure it is working properly Inspect air system to ensure pressure is set between 40 50 PSI CAUTION Use of flammable sub stances can cause severe burns or per sonal injury Always use non flammable solvents for cleaning parts and surfaces of this game Do not use flammable sub stances such as gasoline kerosene or thinners WEEKLY IMPORTANT Do not use cleaning solvents on game graphics Use only a mild soap solution and dry with a clean lint free cloth TASK MONTHLY Clean outside surfaces and stools Balls leave black marks on surfaces Inspect the game for physical damage Repair as needed Inspect game lighting replace lamps as needed Clean outside surfaces Clean th
4. Replace Power Supply Turn power OFF Unplug all outputs from the Gen 5 Circuit Board Recon nect the 12 volt output wires to the Power Supply Turn power ON Green LED Light Green LED Light Short in Main Board comes ON remains OFF Replace That cable or related component is Turn power OFF Recon Green LED Light shorted out See Jumper Cable nect the outputs at the remains OFF Pin Outs to see which component Main Circuit Board one might be at fault at a time Wait 3 minutes between tests to turn power ON Green LED Light dims related component such as a solenoid is causing an overload See Jumper Cable Pin Outs to see which component might be at Green LED Light That cable is OK fault comes ON 25 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Service and Repair Section CAUTION Static electricity could harm circuit boards and processor chips Always ground yourself by ca ble or by touching metal surfaces prior to removing or servicing electronic equipment this game Avoid work ing on carpeted surfaces CAUTION Electrical Shock Hazard Do not perform maintenance or repair of this equipment with power ON Unplug the unit from the wall outlet or shut off power at the power Shut off power to the game at the power strip located in the rear target cabinet 1 Remove the two wire clips from the solenoid 2 Remove the hex
5. As the balls wear down they will not provide a good seal 1n the firing tube and miss fires will occur This can be corrected somewhat by increased air pressure to the fire cylinder but at some point it will be necessary to replace the balls due to wear Turn off the air supply shut off valve located the front cabinet Release the air system pressure by firing the gun once Pull toggle to release the balls Use a short stick to push the balls out into the chute where they be removed See figure 10 WARNING The ball chute air cylin der can pinch cut or sever fingers during ball removal Insure air pres sure is OFF and system pressure is released before attempting to remove balls from the lift system To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 HOW PLAY CANNONBALL BLAST Players have fun shooting balls at the pirate ship in hopes of knocking down the wooden planks Knock down all six planks in three shots or less and get a chance at the bonus by hitting all six planks again with the remaining shots 6 PLANKS 5 d ven fy NOTE Hitting the planks slightly will not score a hit The planks need to be knocked down fully Also there 1s a 2 5 second delay before each ball can be shot If the game does not register a shot after three minutes the game ends and all credits clear The score table dip switch select able
6. ASPOIK d Replace main board with board from another Gen 5 game if possible to isolate the prob lem to the main circuit board a Load tickets Make sure ticket stack rests on top of wire actuator of switch b Replace switch AASW200 c Check cable connections from switch to main circuit board a Replace fuse located in the wiring near the main circuit board b Replace motor AAMO3901 c Inspect the linkage between the reset arm and gear motor Check connector cam setscrew ensure it is tight d If it turns that 1st time then refer to teeth reset bar rotates To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Teeth reset bar rotates up multiple times TROUBLESHOOTING GUIDE AND DIAGNOSTIC SECTION Game does not score Game does not coin up Coin switch prob lem Teeth sensor or motor problem a Motor home sensor dirty or faulty b White cam is dirty or too far away from sensor c Faulty broken wires d Faulty main board a Teeth opto s dirty mis aligned or faulty b Faulty broken wires a Coin switch faulty b Bad connection or broken coin switch wire c Faulty main board a Reset motor problem b Teeth sensor problem c Motor home position sensor dirty or faulty 2 a Clean sensor replace if nec essary AABD5010 b Clean cam Measure 5 Volts DC when cam is away from sensor and
7. CHAPEL 18 CHAPEL J9 1 xi rmm IB z rmm Ji 2 ZHAMEB JH Z iis CHAMEB JIH Z 1 Care Jh JT Caer JH Z IE x camer 18 1 t bs 16 4 man 07 4 1 CEs JH 4 CHED J3 4 r TE 1 n te ug gis HIM 2 PM iran M UN doo ken PIP ane 24 15 T E laos 1 36 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Output Section B Q17 Q24 DuEpguE SJarbinn B TRO C MED Nes H Tali a d T DLs nb rund m 3 DLS a m ww TEL ki Ig 1 g jl DRL et 021 37 1 L 3FER 3 uas J2 20 EN L 3FRK ipa der 19 Fle T 1 25k i T5 1E put I gun 15 14 1 15 10 MEE d 1 EN LE 49 gas To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Output Section C Q5 Q12 FE I 25 PRE 1 1 Pu a TRE mem T as E is w 4 me 1 E hm H Lir Cl ICI ut d El ud I i k 1 Eam 18 14 PE wel Emm HE T un 18 8 ni T ES un s nl i P np BEP IE LEN LI 38 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 5
8. TICKET PAYOUT ALLOWS YOU TO CHOOSE BETWEEN A SELECTABLE TICKET TABLE SEE TICKET PATTERNS OR A FIXED TICKET TABLE SELECTABLE TICKET PATTERNS Ticket amounts are multiplied by credits per play IF YOU CHOOSE TO USE A SELECTABLE TICKET PATTERN USE THE FOLLOWING CHART TO SELECT WHICH PATTERN YOU WOULD LIKE TO USE 15 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PROGRAMMABLE SETTINGS FIXED TICKET PAYOUT IF YOU CHOOSE A FIXED TICKET PATTERN CHOOSE ONE OF THE FOLLOWING PATTERNS NOTE THE PLAYER MAY PLAY THE BONUS ROUND IF IT IS ACHIEVED BUT NO BONUS TICKETS WILL BE WON BONUS TICKETS SET THE NUMBER OF BONUS TICKETS TO BE DISPENSED IN THE BONUS ROUND To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PROGRAMMABLE SETTINGS CREDITS PER PLAY SET THE NUMBER OF COIN CREDITS PER GAME ATTRACT MODE WHEN THE GAME IS NOT IN PLAY AN ATTRACT AUDIO MODE LOOPS TO ATTRACT PLAYERS DISABLED OFF CLEAR EEPROM ALLOWS YOU TO CLEAR ANY UNUSED CREDITS AND TICKET OWED FIRST TURN GAME OFF SET DIP TO ON TURN GAME ON AND WAIT FOR 10 SECONDS TURN GAME OFF TURN DIP OFF 17 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PROGRAMMABLE SETTINGS NOT USED ENABLED NOT USED DISABLED N amino U CTACTA
9. it drops to 0 Volts when cam is covering sensor c Check cable connections from sensor to main circuit board d Replace main board with board from another Gen 5 game if possible to isolate the prob lem to the main circuit board a Clean align or replace opto boards AASE3900 b Check cable connections from sensors to main circuit board Look at where there are 2 wires crimped to one termi nal Ensure both wires are mak ing connection with the termi a Check that coin actually trig gers switch Replace switch if necessary A5SW4000 b Check connections from coin switch to main circuit board c Replace main board with board from another Gen 5 game if possible to isolate the prob lem to the main circuit board a Refer to Teeth do not reset section b Refer to Game does not score section c Clean opto sensor and white cam that the sensor looks at Replace sensor if necessary AABD5010 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLESHOOTING GUIDE AND DIAGNOSTIC SECTION No air blast out of cannon Wrong number of tickets dispensed a No air pressure b Incorrect air pressure c Trigger not working d Boom valve faulty e Bad connection or broken Wire f Faulty main board a Ticket Pattern or other ticket dipswitches set wrong b Dirty opto sensor on ticket dispenser c Many tickets in memory If tick
10. nut holding the solenoid to the quick release valve 10 Ball Firing Solenoid 3 Install the new solenoid and re attach the wires It doesn t matter which wire is attached to which termi nal Turn on the power and test the unit 26 Ain Cono vane _ 1 Shut OFF air pressure at the air shut off valve or the air regulator Release system pressure by firing the guns 2 Disconnect the three air lines in to and out of the control valve 3 Disconnect the wiring connector from the sole noid Remove the mounting screws and remove from the game 4 Install the new plug re attached the wire connec tor from the solenoid and re attached the air lines 5 Return power and air pressure to the game and test by firing the gun several times to insure that the balls are being loaded properly into the lift tube To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Service and Repair Section Ball Sorter Gear Motor The ball sorter gear motor assembly the middle cabinet oscillates the paddles for the ball return chutes to keep the balls from becoming jammed in the chutes Replace as follows M Setscrew 1 Remove the four bolts and washers from the two connector plates holding the front and middle cabi nets together Slide the front cabinet away from the middle cabinet slightly to gain access to the gear mo tor a
11. 61 391 7200 Power Section 10 2 MN Ls ki Jidj 39 14 1 EP JAE IED 14 14 mac 14 11 dagen mn 11 Jt FAD il BICL TEG JOUL in P Zo dL p TUE EH mmc Br E pL TRU gi y nz lur Ii Bn zT pg nur hin TEL IM E nr Mime p DEE Our 40 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Processor Section Input RD E dI 7 dE i To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 MAINTENANCE LOG If you need to make repairs or order replacement parts it is a good idea to keep log Below is a chart you can use to track repairs and maintenance DATE MAINTENANCE PERFORMED PARTS ORDERED INITIALS TECHNICAL SUPPORT Excellent customer service 15 very important to Bay Tek Games We know that keeping your games in great operating condition 1s important to your business When you need us we are here to help You can call us fro free technical assistance and you can count on us to have parts on hand to support your game When you do need us it s important that you know what to expect We offer options that fit your needs Electronics Circuit Boards Repair Options Repair amp Return If you have Circuit Board issues with your Bay Te
12. CTION Balls misfire or shoot 2 at a time Ball lift cylinder is not lifting up all the way a Not enough balls in flex tube b Balls stuck return chute or flex tube c Ball height in flex tube not adjusted correctly d Ball gate cup lifter broken e Pawl spring is not holding the ball above lit cylinder f Balls worn Does not have a tight seal in cannon a Water and or Oil in the air line b Pawl Spring combination jamming balls c Defective ball lift cylinder d Mac Valve improperly set e Defective Mac Valve 23 a Check both sides of game Ensure both sides have at least 25 balls b Check for debris in ball re turn chute Ensure lifter is oper ating correctly c Look down barrel of gun The ball to be fired next should be directly in front of nozzle This position can be adjusted by bending flex tube If ball is too high bend flex tube If ball is too low straighten flex tube d Ensure cupped ball gate has 2 rods coming down One at tached to lift cylinder one as a guide If one is broken replace gate A5GA7100 e Replace pawl and spring 5 7100 and 55 7100 f Old balls do not shoot prop erly Replace balls AABALL ALL a Turn off air Remove air hoses to ball lift cylinder If water drains out an air dryer filter must be added to air sys tem b Replace pawl A5PA7100 and or spring ASSP7100 c Replace ball lift cylin
13. ECAUTIONS 6 INSTALLATION COMPONENTS 7 MAIN CABINET COMPONENTS 8 ASSEMBLY ISTRUCTIONS 9 12 HOW TO PLAY 13 PROGRAMMING 14 18 PREVENTATIVE MAINTENANCE SECTION 19 TROUBLE SHOOTING 20 25 SERVICE AND REPAIR 26 28 WIRING DIAGRAMS 29 32 SCHEMATICS 33 40 MAINTENANCE LOG 41 TECHNICAL SUPPORT 42 WARRANTY 43 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 CANNONBALL BLAST Arrrggghhh Matey Congratulations on your Cannonball Blast purchase This piece is sure to serve as a great addition to your existing shooting games and more importantly will offer your clientele great entertainment value We can proudly say our shooting game line up Horse Play Cannonball Blast amp Sky Masters is viewed as a staple in family entertainment centers across the globe And now because you ve made an investment in quality this pirate ship Is ready to make waves at your own location We hope you take a few moments to read through this manual and encourage you to contact the factory with any further questions you may have Thank you for your business and we wish you great success Your Friends at Bay Tek Games HSL T ze GAME INSPECTION Inspect the game for any damaged loose or missing parts If damage is found please contact your freight carrier first Then contact Bay Tek Games Service Department at 920 822 3951 or e mail them at service baytekgames com for furth
14. To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 HI 4 B aa a i Li EMI UU EN l i E m Bae E w i PLACE SERIAL NUMBER LABEL HERE To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 FACTORY CONTACT INFORMATION BAY TE EK Our Vision We aspire to be the best in the world at developing and ER JOIN SERVICE FIRST NETWORK This free service is intended to keep you up to our customers date on the latest game information early notification of parts specials pertinent technical bulletins updates on retro fit parts software upgrades amp much more Log on to www baytekgames com parts amp then click on the Service First icon 8 AM 5 PM C S T MON FRI Locate All Bay Tek Gamta Service Manuals and Order Parts oniiner www baytekgames com PARTS SERVICE P 920 822 3951 x 1101 P 920 822 3951 X 1102 F 920 822 1496 F 920 822 1496 parts baytekgames com service baytekgames com 2 All games proudly manufactured at our factory in Pulaski Wisconsin U S A To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TABLE OF CONTENTS FACTORY CONTACT INFORMATION 2 TABLE OF CONTENTS 3 INTRODUCTION 4 INSPECTION 4 DIMENSIONS 5 AIR COMPRESSION REQUIREMENTS 6 SAFETY PR
15. alify for any credit amount No shipping charges will be credited 42 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 WARRANTY Bay Tek Games warrants to the original purchaser that all game components will be free of defects in workmanship and materials for a period of 6 months from the date of purchase Hint Register your new game for an extra 3 months on your warranty Find registration card in the cashbox Bay Tek Games will without charge repair or replace at it s option defective component parts upon notification to the parts service department Warranty replacement part s will be shipped immediately via ground service along with a Product Return Form for the return of defective part s Defective part s must be shipped back to Bay Tek Games unless otherwise instructed Items not returned to Bay Tek Games will be invoiced as replacement parts This warranty does not apply the event of any misuse or abuse to the product or as a result of any unauthorized repairs or alterations The warranty does not apply if any serial number decal is altered defaced or removed from it s original position In order to maintain the safety amp other compliance cer tifications of the game ONLY approved parts may be used For approved parts refer to the parts list in this manual Should you need your game serviced determine the serial number from the decal placed on the fr
16. can cause severe burns or serious injury Al ways use NON FLAMMABLE solvents for cleaning DO NOT use gasoline kerosene or thinners Lifting heavy objects can cause back neck or other injuries Be sure ade quate lifting and moving devices are available when unloading unpacking and moving this game Be sure the electrical power matches the game requirements See the serial number decal located on the back of the game cabinet Always plug game into a grounded circuit If the supply cord 1s damaged it must be replaced by a special cord or assembly available from the manufacturer or its service To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 HARDWARE INSTALLATION COMPONENTS You will find the following pieces of hardware in a sealed bag in the cashbox A 1 4 20 x 1 1 2 Bolts Washers 5 16 Lock washers 10 x 5 8 Black wood screws v 10 24 x 1 2 Black self tapping screws es 10 32 Nylon Locknuts 2 Square bit T ASBK7004 1 brackets 4 1 2 to 1 4 Pipe Reducer J A5AC7002 Frosted Acrylic K Black Teflon balls 48 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 MAIN CABINET COMPONENTS FRONT CABINET MARQUEE TICKET PLATE BOX To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Assembly Instructions
17. der A5BL7101 d To increase lift up speed Follow the air line from the bottom of the lift cylinder to the blue Mac valve Loosen the lock nut on the screw that corre sponds to this air line Increase air flow by turning screw clock wise Adjust slightly firing the cannon 3 times before further adjustments Once set correctly re tighten lock nut e Replace Mac Valve 5 7103 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLESHOOTING GUIDE AND DIAGNOSTIC SECTION Ball lift cylinder is not dropping down all the way Tickets do not dispense a Water and or Oil in the air line b Ball gate cup lifter broken c Defective ball lift cylinder d Mac Valve improperly set e Defective Mac Valve a Ticket tray empty due to faulty low ticket sensor switch or broken loose wires Sensor switch stuck or switch wire bent out of position b Faulty cable to dispenser c Dirty opto sensor or paper dust buildup in ticket dispenser d Notch on tickets too shallow e Ticket dispenser faulty f Main circuit board malfunc tion a Turn off air Remove air hoses to ball lift cylinder If water drains out an air dryer filter must be added to air sys tem b Replace ball gate A5GA7100 c Replace ball lift cylinder ASBL7101 d To increase down speed Follow the air line from the top of the lift cylinder to the blue Mac va
18. e ticket dispenser with com pressed air Clean the opto sensor using a cotton swab and isopropyl alcohol Non filtered air pump drain water from hoses WWW NU Check to ensure correct number of balls are present To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLESHOOTING GUIDE AND DIAGNOSTIC SECTION No power to the game No Audio Orange low ticket light on Teeth will not reset Game will only try to reset teeth once Then it will error out and not try again until game powered down then on a Unplugged b Blown fuse Outlet strip or building circuit breaker tripped d Bad power supply a Volume too low b Loose wire c Defective Potentiometer d Main circuit board malfunc Ticket tray empty Faulty low ticket switch Broken loose wires a In line fuse blown b Motor faulty c Linkage problem d Power game off and then back on and see if it turn the Ist time a Check wall outlet b Check transformer fuse 220v applications only c Check voltage at outlets Try to determine cause then reset the circuit breaker d See power supply diagnostic Replace if faulty ASPS1001 a Increase the volume at the volume control at the inside of the front door panel b Check audio cable connec tions to speaker volume control and main circuit board c Replace pot
19. er assistance IMPORTANT Complete your new game registration card located inside the cashbox for an additional 3 months FREE WARRANTY 4 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 f J 10 on Wien 1 WEIGHT EN Weight 875 Ibs Shipping Weight 1115 Ibs DIMENSIONS 47 5 W x 100 D x 88 j Mh 2 es gt Without Stools 80 D n HT 8 a TICKETS Order with GAMES 5 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 AIR COMPRESSION REQUIREMENTS AIR COMPRESSION supplied built into the facility 1 Set air pressure at the regulator for 70 PSI 4 83 bars 2 A pneumatic air supply system with minimum pressure of 85 PSI 5 86 bars Is required to operate this game 3 1 2 1 4 pipe reducer has been supplied for the air connection AIR COMPRESSION portable available through Bay Tek parts dept 1 20 gallon p n ASAC1003 220 conversion available Customers must supply any other fittings and or piping needed SAFETY PRECAUTIONS DO NOT perform repairs or maintenance on this game with the power ON Unplug the unit from the wall outlet or shut off the power at the power strip located inside the game cabinet Use of flammable substances
20. et meter is counting the tickets coming out then reset tickets owed d Faulty ticket dispenser e Main circuit board malfunc tion 22 a Check air line air compres sor Ensure gauge on air line input is working b Adjust compressor to output 90 PSI Adjust game air pres sure to 50 55 PSI c Check trigger button wires to main board Replace switch A5PB7100 by removing bar rel from gun reach inside and remove right handle Switch is then accessible d Check for 12 Volt DC pulse at boom valve Replace boom valve A5VA7100 if pulse is present Check wire continuity back to main board if no pulse e Check connections from boom valve and trigger to main circuit board f Replace main board with board from another Gen 5 game if possible to isolate the prob lem to the main circuit board a Check and reset dipswitches for proper setting b Clean with compressed air or wipe with isopropyl alcohol on a cotton swab c Loop tickets and let dispenser run Or remove memory chip from main board Position U3 Leave chip out of board and turn power on game The game can run fine with this chip re moved d Replace with spare working dispenser e Replace main board with a spare Gen 5 board if possible to isolate the problem to the main circuit board To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 TROUBLESHOOTING GUIDE AND DIAGNOSTIC SE
21. f you need help you know you can call us It s not easy to diagnose a game remotely by phone but our technicians do a great job They ll need your help to perform some troubleshooting steps and convey to them exactly what s hap pening with your game Returns Credits amp Fees NOTICE ALL ITEMS being sent to Bay Tek Games for repair or return etc require prior Return Authorization Bay Tek Games will provide a Product Return Form with an authoriz ing Ticket Number for each item to be returned Please be certain to include this document with all shipments Late Fees and Non Return Fees Advance Replacement and Warranty Replacement items require the defective items to be returned by Bay Tek games promptly to avoid Late Fees We would expect items to be returned with 10 working days Late fees are invoiced monthly Late fees are non refundable under any circumstance Any item not returned within 90 days will be invoiced full as a replacement part Bench Fees Bench fees will apply for each electronic item returned to Bay Tek Games this includes unused Advance Replacement items This charge covers our cost to inspect evaluate and retest each item Please note that returned items that do not pas sour tests will be charged accordingly as replacement items or advance replacements Restocking Fees Unused items returned for credit will be credited minus a restocking fee Items must be returned with 30 days of purchase in order to qu
22. igaming com 800 746 2255 1 561 391 7200 Gen 5 Main Board Schematics Daerden T Lub mI Juf F 4 I FE T LL E 408 OM del a 51 E m LEE nmi 271 n TE ivo ED Mna B ib ga aa n i 33 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Communications Serial EEprom mik in Bm Tm m mrs KL HEHHE 19 E ALD i T HOA ij HIE US El Eil i lla Hililillim 1 J unn 110 Input Section Con Switches gt 1 UPC Lok 1 4 EU z SH 2 E zen FN E a nn E 5 pee 5 e X3 SUD TW MEN AHC E40 id ET 1 i LE o gt et JL SDC 17 34 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Input Section B Inputs RC P 13 13 RASC J3 15 PD CS J3 17 RELD 73 19 RE D 43 20 BREZL 13 18 BEO DE 13 16 RAAD 13 14 post 43 5 J3 7 J3 3 J3 11 J3 12 43 10 43 8 3 6 35 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Output Section Chase lights Q13 Q16 Output eztien Data JE 1 hmem Lights rmx quc
23. ire connector To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Service and Repair Section Circuit Boards Target Score Sensors The score sensors are mounted to a small circuit board and consist of an emitter and a detector on op posite sides of the target flag To replace the sensor board i m m Losses E 1 Open the access door of the rear cabinet un plug the sensor wiring at the connectors on the sensor circuit board 2 Unbolt the sensor boards 3 Replace the sensor boards and reconnect the wire cables 4 Test the sensors by moving the tooth so the tooth flag no longer blocks the sensors and scores a hit 28 Main Circuit Board Replacing the main Gen 5 circuit board 1 Carefully unplug all wiring connectors 2 Remove the four Phillips head screws at the four corners of the board and remove the board from the mounting panel 3 Before installing the new board check to be sure that the dipswitches are set in the same position as the old board NOTE If swapping the circuit board with a spare Gen 5 board for testing purposes be sure to also swap out the software chip Use extreme care to pre vent static electricity and to prevent bending socket pins 4 Install the board and reconnect the wiring connec tors and the white display cable 5 Re test the game Ir Software Chi To Purchase This
24. k game you can send the board to us and we ll repair it right away Most items sent to us are repaired and returned to you within two days This option 15 your best value as we offer this fast turn around service at the most reasonable price Advance Replacement If you have Circuit Board issues with your Bay Tek game but you don t have time to send in your board for repair give us a call and ask for an Advance Re placement We ll send you a replacement board that same day pending availability When you get your new board just repackage the defective board in the same box and send it back to us We make it easy by including a UPS Return Shipping label for you to put on the box not available for international shipments This 15 your best option when you need to get you game up and running as quickly as possible Spare Parts Take matters into your own hands and purchase new spare Circuit Boards for your Bay Tek games Many of our games share the same main board electronics This means you can buy one set of spare electronics to support many of your Bay Tek games Spare boards allow you to get your game up and running the quickest and provide you a valuable troubleshooting option Call our technicians to get recommendations for what you should keep on hand for spare parts Technical Support You are the best tool for troubleshooting Your abilities to understand the game and your skills to repair the game are invaluable to us I
25. lve Loosen the lock nut on the screw that corresponds to this air line Increase air flow by turning screw clockwise Adjust slightly firing the can non 3 times before further ad justments Once set correctly re tighten lock nut e Replace Mac Valve a Fill ticket tray Replace low ticket sensor switch Repair wiring Clean ticket tray of dirt and loose tickets or debris Bend switch wire to correct position under tickets b Check wiring continuity from dispenser to main board Check for pinched broken or discon nected wires Replace as neces sary c Clean with compressed air and if necessary wipe sensor with isopropyl alcohol on a cotton swab d Flip tickets and load upside down to have large cut notch toward opto sensor e Replace dispenser with spare working dispenser f Replace main board with a spare Gen 5 board if possible to isolate the problem to the main circuit board To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Power Supply Troubleshooting Use the following procedure to check the power supply for Gen 5 games Check the small green LED light on the power sup ply circuit board If the light is out there is a short somewhere If the light dims there is an overload in one of the circuits such as a bad motor Turn power OFF Disconnect all 12 volt output wires only Turn power ON Green LED Light Green LED Light comes ON remains OFF
26. mp middle section are uni versal therefore the number and color of wires does not matter Match size of connector only Below is a diagram showing the Inputs to that cable from the target cabinet 30 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Jumper Cable J4 Connector BRW GameCounter Signal PNK Counter 12v ORG R Side Coin Door 12v TAN Ticket Counter Signal GRY L Side Coin In GRY R Side Coin In DBL YEL s Low Ticket Grounds WHT L Side Tkt Enable BLK R Side Tkt Ground WHT R Side Tkt Enable GRN L Side Coin Door Ground GRN R Side Coin Door Ground BLK L Side Tkt BLU L Side Tkt Notch Signal RED L Side Tkt 12v ORG L Side Coin Door 12 BLU R Side Tkt Notch Signal RED R Side Tkt 12v 2d To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Jumper Cable J5 Connector RED Unused L Side Tooth Reset Motor Output inline fuse WHT GRY Unused R Side Tooth Reset Motor Output inline fuse BLU L Side Low Tkt Light Output BRW TAN R Side Low Tkt Unused Output GRN BLK Unused R Side Lift Solenoid Output BLK GRN L Side Teeth R Side Fire Sensor Enable Solenoid Output YEL BLK R Side Teeth L Side Lift Sensor Enable Solenoid Output PUR BRW Unused L Side Fire Solenoid Output 32 To Purchase This Item Visit BMI Gaming www bm
27. ont of this manual or locate it on the back of the game Then contact our Service Department at 920 822 3951 or e mail service baytekgames com NON WARRANTY Should you need your game serviced determine the serial number on the front page of this manual or by locating the decal on the back of the game cabinet and contact our Service De partment at 920 822 3951 or sevice baytekgames com Options and estimated charges will be provided to you for your approval Please remember that any items being sent to Bay Tek Games must include prior return au thorization from our Parts amp Service Department This approval will include a Product Re turn Form which is required to be included with any incoming shipments Repaired part s will be shipped back using the same method which they were received Repairs are war ranted for 30 days from the date of return shipment 43 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 COPYRIGHT NOTICE CANNONBALL BLAST IS A TRADEMARK AND COPYRIGHTS SOLELY OWNED BY BAY GAMES INC iie tb mi c enim ir ner ux Sav EXE D Park 1077 Ent Geren
28. re the marquee to recessed install the dowel pins in the nuts in the top of the rear cabinet stool bases with holes the with 4 bolts A and lock washers bottom of the cabinet and See figure 8 attach the seat EARN b Plug all cable connectors from the middle cabinet into plugs in the front cabinet Plug the gray phone cable into left cable socket on the main board Connect the cabinets to gether with blue brackets securing with 2 bolts and lock washers C d Attach air hose to the building s air supply or portable air compressor Set the air pressure regulator to 70 PSI 4 83 bars c Secure the middle screen to the marquee with 2 black wood screws D See figure 9 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Assembly Instructions 10 Fill the ticket tray The low ticket light will illuminate when there 15 approximately 1 1 2 stacks of tickets left in the ticket tray 11 Inside each front door will be a bag of 8 balls Empty one bag into each side of the ramp Both barrels are pre loaded with 16 balls 12 Plug the power cord into the wall outlet and turn on the power strip Ball Maintenance TO REPLACE BALLS Rubber Balls The black rubber balls are coated with Teflon to increase the life of the ball While very durable the coating will eventually wear off and the rubber material will then begin to wear rapidly
29. s D b Secure the vertical legs of c Install the two top rails which overlap the tops of the outside screens and the rear cabinet Attach the front of the rails to the screens using 4 black self tapping screws E Attach the rails to the recessed nuts in the top of the cabinet with bolts A and lock washers C Secure remaining holes with 6 black wood screws D Push the middle and rear cabinets together securing both left and right sides with brackets H attaching with bolts A lock washers C and flat washers B Be careful not to pinch any wiring See figure 4 zie 4 the screens to the front of the middle cabinet with 16 black wood screws D Secure the screen to the horizontal edge of the cabinet with 6 black wood screws D through holes on the inside of the screen frame To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Assembly Instructions 8 Install the Marquee 4 Fig 9 a Position the marquee on top of the metal rails and pass the power cord and speaker cable through the hole and plug in See figure 7 F J i B c 9 Install the Front Cabinet Position the front cabinet near the middle cabinet Uncoil and pull the air hose through the middle cabinet and out the hole the bottom of the rear cabi net a Tip the cabinet to align and b Secu
30. should match the tickets owed decal on the game panel ndi APER I Sock Dosen the Planks On the Pusa Skips Ta Wi Tickets EN HCN ns Get L6 555 1 PN Phink 2 Or Lan s s 2 3 42 Takes a 88 dE UNE m Factory default as shown To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 Programming Section The number of coins required for each game credit free play number of balls per credit tickets payout etc are pro grammable by dipswitches located on the main circuit board NS k You A Panky Jehan Or Lan 0 1 8 Tetes Kiel ET Bas The main circuit board is located on the 2 4 12 Tickets Wd de onini Bien Ini 46l7 inside back wall of the cabinet Be sure 4 5 16 Tickets b power 1s off before setting these switches 6 2 6 20 20 Ficker Boris Takel A Factorv Settings Bank 1 Factory Settings Bank 2 Ez LE m p E m IMPORTANT Power must be OFF to the game when setting dipswitches Turn OFF the power strip inside the cabinet Set the dipswitches to the desired settings wait 30 seconds and then turn ON power at the power strip 14 To Purchase This Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 PROGRAMMABLE SETTINGS
31. ssembly 2 Pull the two wires up out of the hole in the frame to expose the connector Unplug the connector 3 Remove the setscrew holding the connector cam assembly to the gearbox shaft and pull the cam off the shaft 4 Remove the four locknuts that secure the gear mo tor assembly to the frame 5 Install the new gear motor assembly with the four locknuts The hole in the connector cam 15 flat on one side so the gearbox shaft may have to be rotated slightly to allow the cam to be installed Secure with the setscrew 6 Reconnect the wire connector 7 Slide the two cabinets together being careful not to pinch any wiring and secure with the two connec 27 Teeth Reset Gear Motor Replacement 1 Open the access door in the rear cabinet and unplug the gear motor wiring at the connector 2 Pull the tooth reset arm downward to manually rotate the connector cam to gain access to the set screw Loosen the setscrew and remove the cam from the shaft 3 Remove the four locknuts mounting the motor gearbox assembly in the mounting frame Remove the gear motor assembly from the game 4 Install the new gear motor and secure with the four locknuts 5 Install the connector cam assembly onto the motor shaft and secure with the setscrew The hole in the connector cam is flat on one side so the gearbox shaft may have to be rotated slightly to allow the cam to be installed Secure with the setscrew 6 Reconnect the w
Download Pdf Manuals
Related Search
cannonball blast air.. cannon ball blast game cannonball blast captain morgan