English - Black & Decker
Contents
1. Caution Always place your steam mop with the handle 4 in the upright position when stationary and make sure the steam mop is turned off when not in use Fitting a scent pack Fig J amp K Warning Return the handle 4 to the upright position and turn the steam mop OFF Wait until the steam mop cools down approximately five minutes Slide the door release button 20 the door will open Place the scent pack into the cavity 21 Close the door 22 py pushing it firmly down Use Important This unit will kill 99 9 of bacteria amp germs when used in accordance with this manual and with the micro fibre pad fitted and a continuous run time of 90 seconds Switching on and off To switch the appliance on press the ON OFF button 1 It takes approximately 15 seconds for the steam mop to heat up Note When the steam mop is first turned on the water res ervoir will glow red Once the steam mop is ready to use the water reservoir will glow blue To switch the appliance off press the ON OFF button 1 Caution Never leave the steam mop in one spot on any surface for any period of time Always place the steam mop with the handle 4 in the upright position when stationary and make sure the steam mop is turned off when not in use Caution Always empty the steam mop after use Note When first filled or after running dry it can take up to 45 seconds for steam to be produced Original instructions C ENGLISH g2. Autoselect Technology This steam mop is fitted with an Autoselect dial 2 which shows various cleaning applications They are used to select the correct operating mode for your particular cleaning opera tion Using the Autoselect dial 2 choose from one of the follow ing applications lp Stone Marble Tiles Vinyl The steam mop will select the correct volume of steam required for your particular cleaning operation Note Always check you are using the correct setting before using your steam mop Hints for optimum use General Caution Never use the steam mop without first attaching a cleaning pad During use you can use the cable management clip 9 to keep your cable out of the way of the work area Always vacuum or sweep the floor before using the steam mop The easiest way to use the machine is to tilt the handle to a 45 angle and clean slowly covering a small area at a time Do not use chemical cleaners with your steam mop To remove stubborn stains from vinyl or linoleum floors you can pre treat with a mild detergent and some water before using the steam mop Steam cleaning Place a cleaning pad 6 on the floor with the hook amp loop side facing up Lightly press the steam mop down onto the cleaning pad 6 Connect the steam mop to the mains Turn the Autoselect dial 2 to the required setting Press the ON OFF button 1 It takes approximately 15 seconds for
3. FSM16208 C ENGLISH g Original instructions Intended use Your Black amp Decker steam mop has been designed for sanitising and cleaning sealed hardwood sealed laminate linoleum vinyl ceramic tile stone and marble floors and for refreshing carpets This appliance is intended for indoor household use only Features This appliance includes some or all of the following features 1 ON Off switch Autoselect dial Removable water tank Handle Steam head Steam head cleaning pad Bottom cable tidy hook Top cable tidy hook Cable management clip Warning Read all of the Safety Maintenance Service manual carefully before operating this appliance Read all of this manual carefully before operating the appliance OOonNDON FW P Assembly Warning Before attempting any of the following operations make sure that the appliance is switched off and unplugged and that the appliance is cold and does not contain any water Attaching the handle Fig A Slide the bottom end of the handle 4 into the top end of the steam mop body 12 until it clicks into place The arrow on the handle 4 should be aligned with the top of the steam mop body 12 Attaching the steam head Fig B Slide the bottom end of the steam mop body 12 onto the steam head 5 unt
4. 19 which will allow your steam mop to be hung from a suitable hook on the wall Always ensure that your wall hook is capable of supporting the weight of the steam mop safely Technical data FSM1620S Type 1 Voltage Vos 230 Power Tank capacity Troubleshooting If your appliance seems not to operate properly follow the instructions below If this does not solve the problem please contact your local Black amp Decker repair agent The steam mop is Check the unit is plugged in at the wall not turning on socket Check the unit is switched on using the on off switch 1 Check the fuse in the plug The steam mop is The steam mop will only produce steam not producing once the handle is pulled back from the steam upright position Check that the water tank 3 is full and correctly fitted NOTE When first filled or after running dry it can take up to 45 seconds for steam to be produced Check that the Steam head 5 is firmly docked into the steam mop body 12 Check steps 1 then 2 then 3 The steam mop Check steps 4 then 5 then 6 and then 3 stops producing steam during use The steam mop is The steam mop has 3 settings Turn the producing too autoselect dial 2 to increase the amount of steam being produced Check step 5 The steam mop has 3 settings Turn the much steam during use The steam mop is producing too little steam during use autoselect dial 2
5. stationary and make sure the steam mop is turned off when not in use Carpet refreshing Place a cleaning pad 6 on the floor with the hook amp loop side facing up Lightly press the steam mop down onto the cleaning pad 6 Place the carpet glider 11 on the floor Lightly press the steam mop down onto the carpet glider 11 until it clicks into place Connect the steam mop to the mains Press the ON OFF button 1 It takes approximately 15 seconds for the steam mop to heat up Turn the Autoselect dial 2 to the Wood Laminate set ting Pulling the handle 4 back will activate the steam pump After a few seconds steam will start to come out of the steam head Note When first filled or after running dry it can take up to 45 seconds for steam to be produced Push and pull the steam mop slowly across the carpet to thoroughly refresh each section Note During use you may turn off the steam pump by return ing the handle to the upright position this convenient feature will allow you to leave the steam mop for a short time so that you may move items of furniture then continue cleaning without the need to switch the appliance off When you have finished using the steam mop return the handle 4 to the upright position and turn it OFF and wait until the steam mop cools down approximately five minutes Caution It is important to monitor the water level in the water tank To refill the w
6. to reduce the amount of steam being produced Steam is escaping Refer to the assembly chapter of the manual from unexpected for correct fitting instructions of all parts and areas of the unit accessories Where can get www blackanddecker co uk steammop further information www blackanddecker ie steammop l accessories for my steam mop Original instructions C ENGLISH g Australia Black 8 Decker Australia Pty Ltd 20 Fletcher Road Mooroolbark Victoria 3138 New Zealand Black amp Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black amp Decker 210 Bath Road Slough Berkshire SL1 3YD 90602686 REV 0 Tel 03 8720 5100 Fax 03 9727 5940 Tel 64 9 259 1133 Fax 64 9 259 1122 Tel 01753 511234 Fax 01753 551155 09 2013
7. ater tank and continue to sanitise clean return the handle 4 to the upright position and turn the steam mop OFF Unplug the unit from the electrical wall outlet remove and refill the water tank 3 Caution Never leave the steam mop in one spot on any surface for any period of time Always place the steam mop with the handle 4 in the upright position when stationary and make sure the steam mop is turned off when not in use After use Fig H amp Return the handle 4 to the upright position and turn the steam mop OFF Place the steam mop on the resting mat 7 and wait until the steam mop cools down approximately five minutes Unplug the steam mop from the electrical wall outlet Empty the water tank 3 Remove the cleaning pad 6 and wash it ready for next use Take care to follow the wash care instructions printed on the cleaning pad Wrap the supply cable around the cable tidy hooks 7 8 8 Note The top cable tidy hook 8 rotates to easily release the cable ready for next use Clip the supply cable onto itself using the cable tidy clip 17 close to the plug Place steam mop on the resting mat 7 for storage Note With the handle 4 in the upright position the cable neatly wrapped around the cable tidy hooks 7 amp 8 and secured with the cable tidy clip 17 your steam mop will stand on its own for storage Alternatively there is a hanging bracket 18 built into the hand grip
8. il it clicks into place The steam head can be removed from the Steam mop body by pressing the steam head release button 13 and pulling the steam mop body 12 off the steam head 5 Attaching the water jug Fig C Clip the water jug 3 onto the handle 4 Slide the water jug 3 down into the Steam mop body 12 ensure that the water jug is firmly seated Attaching a cleaning pad Fig D Replacement cleaning pads are available from your Black amp Decker dealer cat no FSMP20 XJ Place a cleaning pad 6 on the floor with the hook amp loop side facing up Lightly press the steam mop down onto the cleaning pad 6 Caution Always place your steam mop with the handle 4 in the upright position when stationary and make sure the steam mop is turned off when not in use Removing a cleaning pad Fig E Caution Always wear suitable shoes when changing the cleaning pad on your steam mop Do not wear slippers or open toed footwear Return the handle 4 to the upright position and turn the steam mop OFF Wait until the steam mop cools down approximately five minutes Place the front of your shoe onto the cleaning pad removal tab 14 and press down firmly Lift the steam mop up off the cleaning pad Caution Always place your steam mop with the handle 4 in the upright position when stationary and make sure the steam mop is turned off when not in use Filling the water tank Fig F The water ta
9. nk on your steam mop is removable for conven ient and easy filling This Steam Mop incorporates an anti calc system to help prolong the life of the system Note Fill the water tank with clean tap water Note In areas of very hard water the use of de ionised water is recommended Remove the water tank 3 Open the filler cap 16 by lifting it up Fill the water tank 3 with water Warning Your water tank has a 460 ml capacity Do not over fill the tank Re fit the filler cap 16 Re fit the water tank 3 Note Ensure the filler cap is firmly secured Note Do not use chemical cleaners with your steam mop Attaching the carpet glider Fig G Place carpet glider on the floor Attach a cleaning pad to the unit Lightly press the steam mop down onto the carpet glider 11 until it clicks into place Caution Always place your steam mop with the handle 4 in the upright position when stationary and make sure the steam mop is turned off when not in use o Removing the carpet glider Fig G Caution Always wear suitable shoes when changing the carpet glider on your steam mop Do not wear slippers or open toed footwear Return the handle 4 to the upright position and turn the steam mop OFF Wait until the steam mop cools down approximately five minutes Place the front of your shoe onto the carpet glider removal tab 15 and press down firmly Lift the steam mop up off the carpet glider 11
10. the steam mop to heat up Pulling the handle 4 back will activate the steam pump After a few seconds steam will start to come out of the steam head Note When first filled or after running dry it can take up to 45 seconds for steam to be produced nn C ENGLISH g Original instructions Ittakes a few seconds for steam to enter the cleaning pad The steam mop will now glide easily over the surface to be sanitised cleaned Push and pull the steam mop slowly across the floor to thoroughly steam clean each section Note During use you may turn off the steam pump by return ing the handle to the upright position this convenient feature will allow you to leave the steam mop for a short time so that you may move items of furniture then continue cleaning without the need to switch the appliance off When you have finished using the steam mop return the handle 4 to the upright position and turn it OFF and wait until the steam mop cools down approximately five minutes Caution It is important to monitor the water level in the water tank To refill the water tank and continue to sanitise clean return the handle 4 to the upright position and turn the steam mop OFF Unplug the unit from the electrical wall outlet remove and refill the water tank 3 Caution Never leave the steam mop in one spot on any surface for any period of time Always place the steam mop with the handle 4 in the upright position when
Download Pdf Manuals
Related Search