Kettle HD4685/30/A
Contents
1. 0 amp Led 80 Water NTC out of range If necessary you can use a soft nylon brush Led 60 amp Led 100 gt Steam NTC out of range The scale filter can also be cleaned in the dishwasher or Led 80 amp Led 100 gt Both NTC s out of range clean the filter by de scaling it in the same way as the kettle Let the filter soak in a cup of warm water with some white De scaling vinegar or an appropriate descaler Fill the kettle with water up to three quarters of the Take the filter out of the cup and rinse it thoroughly maximum level indication and press the on off switch After the kettle has switched itself off add white vinegar OPTIONAL accessories 8 acetic acid or an appropriate descaler up to the maximum level indication Tripple action Filter HD4990 Leave the solution in the kettle overnight Empty the kettle and rinse the inside thoroughly Repeat this procedure if there is still some scale left in the kettle 2 3 EXPLODED VIEW amp PARTS LIST HD4685 30 A Pos Service code Description 1 4222 459 45057 Lid assy Grey 2 4222 459 45065 Element seal 3 4222 459 45060 Body lower White 4 4222 459 45058 Filter assy 1 0 L 5 4222 459 45062 User panel Grey 6 4222 459 45063 Electronics cover 7 9965 000 32709 Plug CS7 8 4222 459 45064 Winder Grey 3 32. Service Service Service Philips Consumer Lifestyle Kettle HD4685 30 A PRODUCT INFORMATION Product meets the requirements regarding interference suppression on radio and television After the product has been repaired it should function properly and has to meet the safety requirements as laid down officially established at this moment TECHNICAL INFORMATION Voltage Frequency Power consumption Contents Kettle Temperature setting Temperature indication Keep warm function Boil ready signal On off indication Color setting SAP coding 220 240 V 50 60 Hz 2000 2400 W 500 1000 cc 40 60 80 100 C 4x LED 40 60 80 100 C Buzzer Light ring on off button White Steel HD4685 30 A DISASSEMBLY AND RE ASSEMBLY ADVISE For this type the heating element and electronics can not be replaced Disassembly Gasket Remove the base by unscrewing the3 Torx screws Open the lid and gently push force maybe needed on the inside of the heater The heater and Gasket will move out of the Kettle body Remove the Gasket from the heater Published by Philips Consumer Lifestyle 11 10 Printed in the Netherlands Re assembly the gasket and heater assy Place the gasket on the heater assy see picture for placement details Make the outside of the gasket and the inside of the Kettle housing were the gasket will be placed w
3. et with plain water Gently push the heater assy with gasket equable in the Kettle body While pushing inwards check if the gasket keeps well around the heater assy Check visual if the gasket is correct placed By filling the kettle with plain water and leaving it for half an hour you can check if the gasket is properly sealing the Kettle Fix the base again Check the functions of the Kettle Copyright reserved Subject to modification PHILIPS REPAIR INSTRUCTION HD4685 30 A Electrical circuit When the appliance does not work check the electrical circuit On Off PCB Heater assy Control Board il Water NTC z l l l l l l Control ae Steam NTC SS a ic Buzzer PCB Selftest electronics Assumption is that the temperature of both NTC s is lt 40 C otherwise below table is not correct Step Action Buzzer Pe ja we Pa ms warm Operate On Off button and keep operated until step 5 BE ee ee If any NTC circuit is not functioning correct further testing is being disabled and an NTC error code is 1 see NTC error below ga a ee ee Eo a it tek f a a a E E ft het a ooe a a 4 1 Operate Keep Warm heck on aa on on 42 Operate Keep Warm check on Seam NTC on __ om ate ae t a a a Fae nn NTC errors Cleaning filter On off led off two leds blinking alternately Clean the filter by rinsing it under a running tap Led 6
Download Pdf Manuals
Related Search