Sun Blade 6000 Modular System Product Notes
Contents
1. Sun Welcomes Your Comments Sun is interested in improving its documentation and welcomes your comments and suggestions Submit comments about this document by clicking the Feedback link at http docs sun com Please include the title and part number of your document with your feedback Sun Blade 6000 Modular System Product Notes part number 820 0055 20 Preface ix Sun Blade 6000 Modular System Product Notes August 2009 CHAPTER 1 Fixed and Open Issues This chapter contains a table of the fixed and open issues for the Sun Blade 6000 modular system Each issue contains a link to a further description of the issue An issue with an Open status means that there is not an available fix for the bug yet If a workaround is available it is explained in the bug description The ILOM issues are grouped according to whether they are opened or fixed in a specific ILOM version chassis software version is also shown in parenthesis TABLE1 Sun Blade 6000 Modular System Issues Workaround Issue Status Available Hardware Open Issues Power Consumption Is Invalid in ILOM if PSU Side Is Under 25A 6438921 on page 11 Open Yes NEM LEDs 6713414 on page 12 Open No ILOM Open Issues Reset Server Modules Running ILOM 2 0 3 10 After Updating the CMM to ILOM 3 0 3 32 Open Yes 6812532 on page 15 The stop CH Command in ILOM 2 0 3 2 is Different Than in ILOM 2 0 3 1 6679679 Open No on page 15 F2. on page 5 Force Power Supply Fans to Low Speed 6845513 on page 7 Upgraded Midplane Available on page 7 Identifying the PCle 2 0 Midplane on page 8 Available Modules on page 9 Mounting Systems in Square Hole Racks on page 10 Shipping Bracket for Sun Rack 1000 Racks on page 10 Empty Slot Requires Filler on page 10 Light Load Efficiency Mode LLEM The Light Load Efficiency Mode LLEM is a new feature of CMM ILOM 3 0 6 11 To enable or disable LLEM use the command set CMM policy LIGHT_LOAD_EFFICIENCY_MODE enabled disabled When LLEM is disabled you can turn the PSU sides on or off with the command set CMM policy MONITOR_PSx SIDEy enabled disabled Note It s advisable to disable any PSU side first before unplugging the power cord While enabled LLEM runs in both redundant and non redundant mode Under the LLEM CMM monitors the power being used and automatically shuts down the PSU sides to achieve higher efficiency You can check the sensor value of CH PSx Sy I_V12 or CH PSx Sy V_OUT_OK where the value of I_V12 being 0 or V_OUT_OK deasserted indicates the corresponding side is disabled CMM always disables PSU sides in descending order When the power load level increases CMM re enables those disabled sides to cover the demand If a new blade is inserted into the chassis they can be powered on even if their power budget exceeds the power available from the si
3. on page 11 a NEM LEDs 6713414 on page 12 Power Consumption Is Invalid in ILOM if PSU Side Is Under 25A 6438921 This could result in missing information in the ILOM CLI and web interface The following readings will occur if the power supply current is lt 25 Amps m If any side of an installed power supply unit PSU is drawing lt 25 Amps of current the ch dc_watts and ch ac_watts IPMI sensors will show disabled when viewed with ipmitool m The IPMI sensors psx dc_watts psx ac_watts and psx peff will also show disabled where x is the PSU that has a side drawing lt 25 Amps a If any of the above conditions are true such that chassis watts cannot be calculated actual power cannot be calculated You will get the following output when you type the show command in CLI show CMM powermgmt actual_power none Workaround You can determine the amount of current a PSU side is drawing by reading the psx 112V_z sensor where x 0 1 PSU and z 0 1 PSU side If using the CLI you can determine the amount of current a PSU is drawing by typing show CH PSx Sy I_12V Where x 0 1 PSU and y 0 1 PSU side Chapter 2 Hardware Notes and Issues 11 NEM LEDs 6713414 The following tables show LED behavior for 10 100 1000 MB Ethernet LEDs for Sun Blade 6000 network express modules NEMs The LED color can be different depending on the server module that is using the Ethernet port The LED speeds show
4. 0 3 1 Chapter 3 ILOM Notes and Issues 25 NET MGT 1 Port which is the Ethernet port of the CMM will be disabled by default NET MGT 1 Port will be delivered disable because of the inability to guarantee the setup of your network if your network is not configured properly using this port can cause network degradation Future software upgrades will allow for either port to be connected and possibly both ports to be enabled if the certain features of the network can be guaranteed Chassis Reports as Powered on When Powered Off 6531040 This issue was fixed in ILOM 2 0 3 1 The chassis reports as powered on when it is powered off Workaround Reset the CMM then retry the operation again SP Allows One CLI Session 6540550 This issue was fixed in ILOM 2 0 3 1 The ILOM CMM service processor only allows a single remote ILOM CLI session to be started via the CH BLN SP c1i object at a time If an existing CLI session is active and a second CLI session is initiated an error message might display Workaround To avoid this issue you should use ssh from a remote system to initiate additional sessions to a remote ILOM or use the following command to terminate the current session stop CH BLN SP cli 26 Sun Blade 6000 Modular System Product Notes e August 2009 Issues Fixed in ILOM 1 1 6 Two Connected CMM Gigabit Ethernet Ports Causes Slow Network 6498417 This issue was fixed in ILOM 1 1 6 The netw
5. Fixed Yes 6516034 on page 27 BMC Stops Responding and the CPLD Version Displays as 0 0 6517737 on page 27 Fixed Yes Documentation Open Issues Incorrect Directory for DHCP IP address in Getting Started Guide 6589651 on page 29 Open No Incorrect Document Reference in Integrated Lights Out Manager ILOM Administration Open No Guide 6595111 on page 29 URL Clarification for Integrated Lights Out Manager ILOM Administration Guide Open No 6596617 on page 30 Incorrect Note in Integrated Lights Out Manager ILOM Administration Guide Open No 6628649 on page 31 Service Processor Information Missing From Installation Guide 6692159 on page 31 Open No References to Integrated Lights Out Manager ILOM Documentation on page 32 Open No Power Supply Module Rating Incorrect in Some Documentation on page 32 Open No Supported Racks List Is Incorrect in Installation Guide on page 32 Open No Chapter 1 Fixed and Open Issues Sun Blade 6000 Modular System Product Notes August 2009 CHAPTER 2 Hardware Notes and Issues This chapter describes hardware issues and notes related to the Sun Blade 6000 modular system It includes the following issues Hardware Notes on page 5 Hardware Open Issues on page 11 Hardware Notes This section describes items to note regarding hardware for the Sun Blade 6000 modular system Light Load Efficiency Mode LLEM
6. Issues 5 Hardware Notes 5 Light Load Efficiency Mode LLEM 5 Redundant Mode 6 Non Redundant Mode 6 Force Power Supply Fans to Low Speed 6845513 7 Upgraded Midplane Available 7 Identifying the PCIe 2 0 Midplane 8 Y View Component Information Using the CLI 8 Y View Component Information Using the Web Interface With ILOM 2 x 8 Y View Component Information Using the Web Interface With ILOM 3 x 9 Available Modules 9 Mounting Systems in Square Hole Racks 10 Shipping Bracket for Sun Rack 1000 Racks 10 Empty Slot Requires Filler 10 Hardware Open Issues 11 Power Consumption Is Invalid in ILOM if PSU Side Is Under 25A 6438921 11 NEM LEDs 6713414 12 3 ILOM Notes and Issues 13 ILOM Notes 13 Updating ILOM Firmware 13 ILOM 3 0 3 32 and Later Documentation 14 ILOM Open Issues 14 Issues Specific to ILOM 3 0 3 32 14 Reset Server Modules Running ILOM 2 0 3 10 After Updating the CMM to ILOM 3 0 3 32 6812532 15 Issues Specific to ILOM 2 0 3 2 15 The stop CH Command in ILOM 2 0 3 2 is Different Than in ILOM 2 0 3 1 6679679 15 Issues Specific to ILOM 2 0 3 1 16 FRU ID Data Correction for ILOM 2 0 3 1 6631275 16 General ILOM Issues 18 ILOM Service Processor SP Lockup 6471005 18 CH BLn SP cli User Command Accepts Invalid Values 6497752 18 Startcli Does Not Authenticate LDAP and Radius Users 6526825 18 CMM Does Not Change or Detect Blade s SP 6531753 6529037 19 Moving the CMM to a Different Chassis Can Caus
7. Updates For product updates that you can download for the Sun Blade 6000 modular system go to the following URL and navigate to the page for this product http www sun com servers blades downloads jsp Note The Sun Blade 6000 modular system chassis management module CMM and server module service processors must all be upgraded to the latest firmware release Make sure to update the server modules first then the Sun Blade 6000 CMM to the latest firmware using ILOM CLI GUI or IPMI interfaces vii Related Documentation The document set for the Sun Blade 6000 modular system is described in the Where To Find Sun Blade 6000 Modular System Documentation sheet that is packed with your system Additionally you can find the Sun Blade 6000 modular system documentation at http docs sun com app docs prod blade 6000mod Translated versions of some of these documents are available at http docs sun com Select a language from the drop down list and navigate to the Sun Blade 6000 document collection using the workstation category link Available translations for the Sun Blade 6000 modular system include Simplified Chinese Traditional Chinese French Japanese and Korean Documentation Support and Training Sun Function URL Documentation http www sun com documentation Support http www sun com support Training http www sun com training viii Sun Blade 6000 Modular System Product Notes August 2009
8. supply kill signal is being asserted which causes DC output of the power supply to stop Update your firmware to ILOM version 2 0 3 2 in software release 1 2 to fix this issue Sun Blade 6000 Modular System Product Notes August 2009 Issues Fixed in ILOM 2 0 3 1 Fan Thresholds Not Read by the CMM and Blades 6513836 This issue was fixed in ILOM 2 0 3 1 The ILOM service processor does not report threshold information that is not used or controlled by the service processor Therefore fan and power supply threshold values cannot be read by the CMM and blades Removing a Fan Logs Assert and Deassert Events in CMM SEL 6514930 This issue was fixed in ILOM 2 0 3 1 When a fan is removed or installed an assert and deassert event is logged for each event in the IPMI SEL log The example below shows the assert and dessert event messages displayed when the fan is removed or installed After fan is removed 100 01 18 2007 23 53 17 Fan fm0 fail Predictive Failure Deasserted 200 01 18 2007 23 53 17 Fan fm0 fail Asserted Predictive Failure After fan is installed 100 01 18 2007 23 53 17 Fan fm0 fail Predictive Failure Deasserted 200 01 18 2007 23 53 17 Fan fm0 fail Predictive Failure Asserted 300 01 18 2007 23 54 12 Fan fm0 fail Predictive Failure Deasserted These messages can be safely ignored CMM NET MGT 1 Port Disabled 6521145 This issue was fixed in ILOM 2
9. 0 Modular System has specific ILOM 3 0 information for the Sun Blade 6000 modular system An overview of the Sun Blade 6000 modular system and server module firmware update guidelines is available in the Sun Blade 6000 Modular System Overview ILOM Open Issues The following issues apply to the Sun Blade 6000 modular system ILOM m Issues Specific to ILOM 3 0 3 32 on page 14 m Issues Specific to ILOM 2 0 3 2 on page 15 m Issues Specific to ILOM 2 0 3 1 on page 16 m General ILOM Issues on page 18 Issues Specific to ILOM 3 0 3 32 The issues in this section are specific to the ILOM 3 0 2 32 on the Sun Blade 6000 modular system 14 Sun Blade 6000 Modular System Product Notes August 2009 Reset Server Modules Running ILOM 2 0 3 10 After Updating the CMM to ILOM 3 0 3 32 6812532 When updating the CMM ILOM firmware from 2 0 3 10 to 3 0 3 32 the share sensor ID is changed so a server module running ILOM 2 x cannot read the share sensor correctly Workaround When the CMM is updated to ILOM 3 0 reset all server module SPs that are running ILOM 2 x Issues Specific to ILOM 2 0 3 2 The issues in this section are specific to the ILOM 2 0 3 2 on the Sun Blade 6000 modular system The stop CH Command in ILOM 2 0 3 2 is Different Than in ILOM 2 0 3 1 6679679 The following commands have new functionality for ILOM 2 0 3 2 m stop CH This command now defaults to graceful shutdown instead of a forced
10. 21145 25 Chassis Reports as Powered on When Powered Off 6531040 26 SP Allows One CLI Session 6540550 26 Issues Fixed in ILOM 1 1 6 27 Two Connected CMM Gigabit Ethernet Ports Causes Slow Network 6498417 27 Contents v vi PSU I_12V Sensor Reads 2 5 Amps Instead of 0 When Power Cord is Unplugged 6516034 27 BMC Stops Responding and the CPLD Version Displays as 0 0 6517737 27 Documentation Issues 29 Incorrect Directory for DHCP IP address in Getting Started Guide 6589651 29 Incorrect Document Reference in Integrated Lights Out Manager ILOM Administration Guide 6595111 29 URL Clarification for Integrated Lights Out Manager ILOM Administration Guide 6596617 30 Incorrect Note in Integrated Lights Out Manager ILOM Administration Guide 6628649 31 Service Processor Information Missing From Installation Guide 6692159 31 References to Integrated Lights Out Manager ILOM Documentation 32 Power Supply Module Rating Incorrect in Some Documentation 32 Supported Racks List Is Incorrect in Installation Guide 32 Sun Blade 6000 Modular System Product Notes August 2009 Preface This document describes hardware issues software issues and documentation issues for the Sun Blade 6000 modular system Issues include information that you should know about such as prerequisites tips troubleshooting hints and change requests Change requests have tracking numbers shown in parentheses Product
11. If the CMM is replaced or moved to a different chassis the first time ILOM boots an incorrect host name or product serial number might be displayed Workaround After ILOM boots reset the CMM with one of the following m CLI Execute the reset CH CMM command m Web interface a Log in to the ILOM web interface as an Administrator or Operator b Navigate to the CMM Maintenance tab a If you are running ILOM 3 x first click CMM in the left column to display the Maintenance tab a If you are running ILOM 2 x the Maintenance tab is viewable on the main page c Click the Reset Components sub tab and select CH CMM The CMM will reboot with the correct product information Chapter 3 ILOM Notes and Issues 19 20 Fixed ILOM Issues The issues fixed in specific ILOM releases are listed in this section The issues are listed under the ILOM version that provides a fix for the issue Some of the issues were found in a particular ILOM update m Issues Fixed in ILOM 3 0 3 32 on page 20 m Issues Fixed in ILOM 2 0 3 10 on page 23 m Issues Fixed in ILOM 2 0 3 3 on page 23 a Issues Fixed in ILOM 2 0 3 2 on page 24 a Issues Fixed in ILOM 2 0 3 1 on page 25 m Issues Fixed in ILOM 1 1 6 on page 27 Issues Fixed in ILOM 3 0 3 32 CMM OK LED Turns Off During Boot 6474460 This issue was found in ILOM 2 0 3 10 and fixed in ILOM 3 0 3 32 The CMM OK LED which is located on the CMM front panel li
12. RU ID Data Correction for ILOM 2 0 3 1 6631275 on page 16 Open Yes ILOM Service Processor SP Lockup 6471005 on page 18 Open No CH BLn SP cli User Command Accepts Invalid Values 6497752 on page 18 Open Yes Startcli Does Not Authenticate LDAP and Radius Users 6526825 on page 18 Open Yes CMM Does Not Change or Detect Blade s SP 6531753 6529037 on page 19 Open Yes Moving the CMM to a Different Chassis Can Cause Incorrect Product Data 6821052 on Open Yes page 19 TABLE1 Sun Blade 6000 Modular System Issues Workaround Issue Status Available Fixed in ILOM 3 0 3 32 Sun Blade 6000 Chassis SW 3 0 CMM OK LED Turns Off During Boot 6474460 on page 20 Fixed No TLOM CMM SP Does Not Display Current Status Information 6516108 on page 20 Fixed No CH LOCATE Does Not Turn Off When Set to ON Using the ILOM CLI or ipmitool Fixed No 6695802 on page 21 Locate LED Does not Turn on During Chassis Lamp Test 6713569 6711416 on page 21 Fixed No SP Reports Incorrect FM NEM and Server Module Removal and Insertion Events Fixed No 6744044 on page 21 SP Login Through Web Interface Fails After a New IP Address Is Assigned 6745118 on Fixed Yes page 21 Cannot Set Netmask When Running ILOM 2 0 3 10 6766379 on page 22 Fixed Yes Stop Start and Reset Commands are Disabled for the Virtualized NEM in the Sun Blade Fixed No 6000 CMM 6813859 and 6812683 on page 22 Fi
13. Sun microsystems Sun Blade 6000 Modular System Product Notes Sun Microsystems Inc www sun com Part No 820 0055 21 August 2009 Revision A Submit comments about this document by clicking the Feedback link at http docs sun com Copyright 2009 Sun Microsystems Inc 4150 Network Circle Santa Clara California 95054 U S A All rights reserved Sun Microsystems Inc has intellectual property rights relating to technology fiat is described in this document In particular and without limitation these intellectual property rights may include one or more of the U S patents listed at http www sun com patents and one or more additional patents or pending patent applications in the U S and in other countries This document and the product to which it pertains are distributed under licenses restricting their use copying distribution and decompilation No part of the product or of this document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the po may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and in other countries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo Java AnswerBook2 docs sun com Sun Blade and Solaris are trademarks or r
14. Unis et dans d autres pays Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc AMD Opteron est une marque de fabrique ou une marque deposee de Advanced Microdevices Inc L interface d utilisation graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconna t les efforts de pionniers de Xerox pour la recherche et le d veloppement du concept des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique Sun d tient une license non exclusive de Xerox sur l interface d utilisation grephique Xerox cette licence couvrant galement les licenci es de Sun qui mettent en place l interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences crites de Sun LA DOCUMENTATION EST FOURNIE EN L TAT ET TOUTES AUTRES CONDITIONS DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE A L APTITUDE A UNE UTILISATION PARTICULIERE OU A L ABSENCE DE CONTREFA ON Si BA Adobe PostScript Contents Preface vii Fixed and Open Issues 1 Hardware Notes and
15. a Clara Californie 95054 Etats Unis Tous droits r serv s Sun Microsystems Inc a les droits de propri t intellectuels relatants a la technologie qui est d crit dans ce document En particulier et sans la limitation ces droits de propri t intellectuels peuvent inclure un ou plus des brevets am ricains num r s a http www sun com patents et un ou les brevets plus suppl mentaires ou les applications de brevet en attente dans les Etats Unis et dans les autres pays Ce produit ou document est prot g par un copyright et distribu avec des licences qui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne peut tre reproduite sous aucune forme par quelque moyen que ce soit sans l autorisation pr alable et crite de Sun et de ses bailleurs de licence s il y en a Le logiciel d tenu par des tiers et qui comprend la technologie relative aux polices de caract res est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par l Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun Java AnswerBook2 docs sun com Sun Blade et Solaris sont des marques de fabrique ou des marques d pos es de Sun Microsystems Inc aux Etats
16. art Number column If the part number is 541 3789 0x the upgraded PCIe 2 0 midplane is installed If the part number is 541 1983 0x the previous version of the PCIe midplane is installed Available Modules There are a number of server modules storage modules PCIe ExpressModules PCIe EMs and Network ExpressModules NEMs available for the Sun Blade 6000 modular system For information on server or storage modules that are available for the Sun Blade 6000 modular system refer the links for each server or storage module at http www sun com servers blades 6000chassis For information on PCIe EMs and NEMs that are available for the Sun Blade 6000 modular system see http www sun com servers blades optioncards jsp You can also view documentation for these modules at http docs sun com Chapter 2 Hardware Notes and Issues 9 Mounting Systems in Square Hole Racks The current version of the Sun Blade 6000 Rack Alignment Template 263 2755 03 contains instructions for mounting systems in a square hole rack The original version of the template 263 2755 01 does not contain these instructions If you wish to mount your system in a square hole rack and the 263 2755 03 version of the rack alignment template document was not included with your rail kit you can view this document on the Sun Blade 6000 modular system documentation page located at http docs sun com app docs prod blade 6000mod Note If you hav
17. be in tftp format For example tftp zbank ah27901 CMM PO rom pkg The http format will not work for this command 30 Sun Blade 6000 Modular System Product Notes August 2009 Incorrect Note in Integrated Lights Out Manager ILOM Administration Guide 6628649 Page 5 6 of the Integrated Lights Out Manager ILOM Administration Guide For the Sun Blade 6000 Modular System 820 0052 10 has the following note Note The upgrade takes about five minutes During this time no other tasks can be performed in the CMM ILOM A successful firmware causes the CMM ILOM to reboot A firmware upgrade causes the server and the CMM ILOM to be reset It is recommended that a clean shutdown of the server be done prior to the upgrade procedure An upgrade takes about 6 minutes to complete The CMM ILOM enters a special mode to load new firmware No other tasks can be performed in the CMM ILOM until the firmware upgrade is complete and the CMM ILOM is reset The last two statements are incorrect The server will not be reset during a CMM firmware upgrade Service Processor Information Missing From Installation Guide 6692159 It is possible to set the service processors for the server modules with different subnet IP addresses than the IP address of the chassis CMM This information is not included in the Installation Guide but will be added to the next update of the document Chapter 4 Documentation Issues 31 References to Integra
18. d The only recovery mechanism is to install the ILOM build provided with Software 1 1a Identifying your ILOM Firmware You can identify your ILOM firmware using the ILOM CLI or web interface m From the CLI enter the version command m From the web interface bring up the System Information Versions tab In the information you obtain find the Firmware Version just Firmware in the CLI and Firmware Build Number Depending on the values you obtain you should take one of the following actions a If the Firmware Version is 2 0 3 1 and the Firmware Build Number is 23240 then you have installed the ILOM firmware included in Software 1 1 You must install the replacement ILOM firmware in Software 1 1a and re enter some lost data as described in Lost FRU Data and How To Fix It on page 17 a If the Firmware Version is 2 0 3 1 and the Firmware Build Number is 26140 then you have already installed the ILOM firmware included in Software 1 1a No further action is required Sun Blade 6000 Modular System Product Notes August 2009 m If you downgraded from Firmware Version 2 0 3 1 to Firmware Version is 1 1 x with any build number you will must install the replacement ILOM firmware in Software 1 1a You must then re enter the FRU ID data that was lost as described in Lost FRU Data and How To Fix It on page 17 Lost FRU Data and How To Fix It The ILOM bug causes the following FRU data
19. d m Use the ILOM CLI reset SP command m Use the ILOM web interface maintenance tab CH BLn SP cli User Command Accepts Invalid Values 6497752 The CH BLx SP cli user command accepts invalid values This issue will be fixed in a future release Workaround Insert a valid user name in user property field Startcli Does Not Authenticate LDAP and Radius Users 6526825 When an LDAP or radius user tries to authenticate authentication is not allowed Workaround To authenticate LDAP radius user and connect as the desired user use the root login then set the CLI user property to allow remote connection 18 Sun Blade 6000 Modular System Product Notes August 2009 CMM Does Not Change or Detect Blade s SP 6531753 6529037 The CMM might not allow you to change or detect the blade IP address To change the IP address connect to the blade service processor then use the blade s service processor ILOM interfaces to update and display the IP address There are several methods available to access the blade ILOM use one of the following workarounds Workaround m From the blade server use the IPMI KCS interface m From a network host use the IPMI protocol and management network m From the ILOM CLI use ssh and the management network a From the CMM ILOM CLI use the following start command start CH BLn SP cli Moving the CMM to a Different Chassis Can Cause Incorrect Product Data 6821052
20. des currently turned on Redundant Mode The redundant mode is set by the command set CMM powermgmt redundancy n n All MONITOR_PSx_SIDEy are set to enabled and any attempt to disable any PSU side s monitoring is not allowed For example the command set CMM policy MONITOR_PSx_SIDEy disabled will result in an error Non Redundant Mode The non redundant mode is set by the command set CMM powermgmt redundancy none You can disable any PSU sides monitoring for example a side that doesn t have a power cord In both redundant and non redundant modes LLEM works on those sides that are under monitoring Sun Blade 6000 Modular System Product Notes August 2009 When an unexpected AC fault happens LLEM will be suspended and all sides will become enabled verified by the sensor value of I_V12 and V_OUT_OK If the fault is cleared LLEM will automatically go back into effect When the LLEM is disabled all PSU sides including those previously disabled become enabled This can be verified by the sensor value of I_V12 and V_OUT_OK For detailed information on ILOM 3 0 6 see the ILOM Feature Updates and Release Notes Force Power Supply Fans to Low Speed 6845513 A new feature allows the adjustment of power supply fans to low speed On the ILOM Web interface click on CMM then the Configuration tab and the Policy sub tab Choose the option Force Power Supply fans to low speed As the power supply fans c
21. e Incorrect Product Data 6821052 19 Fixed ILOM Issues 20 Issues Fixed in ILOM 3 0 3 32 20 CMM OK LED Turns Off During Boot 6474460 20 ILOM CMM SP Does Not Display Current Status Information 6516108 20 iv Sun Blade 6000 Modular System Product Notes August 2009 CH LOCATE Does Not Turn Off When Set to ON Using the ILOM CLI or ipmitool 6695802 21 Locate LED Does not Turn on During Chassis Lamp Test 6713569 6711416 21 SP Reports Incorrect FM NEM and Server Module Removal and Insertion Events 6744044 21 SP Login Through Web Interface Fails After a New IP Address Is Assigned 6745118 21 Cannot Set Netmask When Running ILOM 2 0 3 10 6766379 22 Stop Start and Reset Commands are Disabled for the Virtualized NEM in the Sun Blade 6000 CMM 6813859 and 6812683 22 Issues Fixed in ILOM 2 0 3 10 23 Power LED Does Not Display Until SP Boots 6464862 23 Issues Fixed in ILOM 2 0 3 3 23 SNMP Trap Destination Port Should Be Configurable 6654887 23 The stop CH Command Lights the Chassis Alert LED 6678328 23 LED Test Mode Causes An SEL Message 6713569 24 Issues Fixed in ILOM 2 0 3 2 24 ILOM Reports Different Status Value When PSU is Removed 6530748 24 DC Output Power Supply Issue Fixed in ILOM 2 0 3 2 6664200 24 Issues Fixed in ILOM 2 0 3 1 25 Fan Thresholds Not Read by the CMM and Blades 6513836 25 Removing a Fan Logs Assert and Deassert Events in CMM SEL 6514930 25 CMM NET MGT 1 Port Disabled 65
22. e an older rail kit part number 371 2986 01 the brackets are all the same for front and back so you can ignore references to front and rear brackets in the 263 2755 023 rack alignment template If you have trouble mounting the system with the 371 2986 01 rail kit please contact your Sun service representative about updating your rack kit Shipping Bracket for Sun Rack 1000 Racks If you plan to ship your Sun Blade 6000 modular system installed in a rack you will need to install the shipping support brackets that are included in the system rail kit Note After the system has been shipped you will need to remove the front shipping bracket support and reinstall the original screws into the rack before operating the system For instructions on installing the shipping brackets refer to the Installing Shipping Brackets on a Sun Blade 6000 Modular System 820 2388 posted on the Sun Blade 6000 modular system documentation site at http docs sun com app docs prod blade 6000mod Empty Slot Requires Filler Do not operate the system with empty slots Fillers are required for proper chassis airflow Always insert a filler into an empty slot to reduce the possibility of module shut down 10 Sun Blade 6000 Modular System Product Notes August 2009 Hardware Open Issues This section describes hardware issues for the Sun Blade 6000 modular system a Power Consumption Is Invalid in ILOM if PSU Side Is Under 25A 6438921
23. egistered trademarks of Sun Microsystems Inc in the U S and in other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S and in other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc AMD Opteron is a trademark or registered trademark of Advanced Microdevices Inc The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees viho implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements U S Government Rights Commercial use Government users are subject to the Sun Microsystems Inc standard license agreement and applicable provisions of the FAR and its supplements DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 2009 Sun Microsystems Inc 4150 Network Circle Sant
24. express module NEM and server module blade BL removal and insertion event logs repeatedly though no insertion or removal has taken place SP Login Through Web Interface Fails After a New IP Address Is Assigned 6745118 This issue was fixed in ILOM 3 0 3 32 If you change the CMM IP address in the SP web interface you can not log into the web interface using the new IP address You can only log into the CLI interface Workaround If you change the CMM IP address in the web interface you must log into the CLI interface to reconfigure the IP address then log into the web interface with the new IP address Chapter 3 ILOM Notes and Issues 21 22 To change the IP address in the ILOM CLI 1 Log in to the ILOM CLI 2 Type the following commands to set the SP working directory cd CMM network 3 Type the show command to view the IP address assigned 4 Type the following commands to change the existing settings set pendingipaddress ipaddress Where ipddress is the new IP address For more information on configuring the IP address in the web interface refer to the Sun Integrated Lights Out Manager User s Guide for the version of ILOM that you are running Cannot Set Netmask When Running ILOM 2 0 3 10 6766379 This issue was found in ILOM 2 0 3 10 and fixed in ILOM 3 0 3 32 If you are running ILOM version 2 0 3 10 you will not be able to set the CMM netmask through the CMM ILOM Workaround To set the netma
25. ghts up for approximately one minute before turning off whenever CMM is inserted into chassis or chassis AC is completely power cycled ILOM CMM SP Does Not Display Current Status Information 6516108 This issue was fixed in ILOM 3 0 3 32 The ILOM CMM service processor does not report current detailed power supply or fan status information When a PSU fan is removed the CLI and IPMItool does not report this change To determine fan or power supply status information you should check the following objects m CH PSx V m CH PSX V_12V MAIN m CH PSX FAN FAIL Sun Blade 6000 Modular System Product Notes August 2009 CH LOCATE Does Not Turn Off When Set to ON Using the ILOM CLI or ipmitool 6695802 This issue was fixed in ILOM 3 0 3 32 CH LOCATE does not turn off when set to ON Fast_Blink using ipmitool or CLI However when the chassis Locate LED button is pressed it times out and goes off after 30 minutes as expected Locate LED Does not Turn on During Chassis Lamp Test 6713569 6711416 This issue was fixed in ILOM 3 0 3 32 When running ILOM 2 0 3 3 if you press the locate button more than 5 seconds to initiate the lamp LED test the LED does not turn on anda transition to degraded message appears in the SEL log SP Reports Incorrect FM NEM and Server Module Removal and Insertion Events 6744044 This issue was found in ILOM 2 0 3 10 and fixed in ILOM 3 0 3 32 The SP reports fan module FM network
26. n in the table are defined below m Standby blink The system is functioning at a minimal level and is ready to resume full function Defined as a repeating sequence consisting of 0 1 second ON followed by 2 9 seconds OFF Blink Transitory or new activity represented by the colored indicator is taking place Defined as 1Hz 50 duty cycle 10 100 MB RJ45 Connector 1 GbE RJ45 Connector Server Left Right Left Right Module Activity LED Link LED Activity LED Link LED X6220 green blink amber standby green blink green standby X6240 green blink amber standby green blink green standby X6250 green blink amber standby green blink green standby X6270 green blink amber standby green blink green standby X6450 green blink amber standby green blink green standby T6300 green blink green standby green blink amber standby T6320 green blink green standby green blink amber standby T6340 green blink amber standby green blink green standby Note See the chassis and NEM documentation for specifics on the Ethernet connections available for each NEM 12 Sun Blade 6000 Modular System Product Notes August 2009 CHAPTER 3 ILOM Notes and Issues This chapter describes the Sun Integrated Lights Out Manager ILOM Service Processor updates and issues It includes the following sections a ILOM Notes on page 13 m ILOM Open Issues on page 14 a Fixed ILOM Issues on page 20 ILOM Notes Updating ILOM Firmware Su
27. n recommends using the latest released firmware for all Sun Blade 6000 modular system components The current release and most recent previous release are tested and available on the Sun download center at http www sun com servers blades downloads jsp Sun tests each new hardware component and firmware update for existing modules against other chassis components that are using the latest available firmware and the prior revision Sun recommends that all components use the latest available firmware or the prior version In order to use the full functionality of ILOM 3 0 the server modules must also be updated to ILOM 3 0 However ILOM 3 0 is not required for the server modules to operate in a ILOM 3 0 CMM chassis Refer to your server module documentation for available ILOM versions This document also contains information on known issues with ILOM version compatibility 13 Note The latest ILOM version for the Sun Blade 6000 modular system CMM is ILOM 3 0 3 32 Refer to the Sun Integrated Lights Out Manager 3 0 Supplement for the Sun Blade 6000 Modular System for specific information on ILOM 3 0 3 32 For instructions on updating the firmware refer to the ILOM documentation for the ILOM version that is currently running on your system ILOM 3 0 3 32 and Later Documentation ILOM version 3 0 3 32 and later provides significant changes in ILOM functionality The Sun Integrated Lights Out Manager 3 0 Supplement for Sun Blade 600
28. network The correct directory path is CMM network Incorrect Document Reference in Integrated Lights Out Manager ILOM Administration Guide 6595111 In the Integrated Lights Out Manager ILOM Administration Guide for the Sun Blade 6000 Modular System 820 0052 10 the document incorrectly states that information on resetting the ILOM password with a jumper is available in the Sun Blade 6000 Modular System Installation Guide This information is not available in the Installation Guide The instructions for resetting the ILOM password are below 29 Note See the Sun Blade 6000 Modular System Service Manual for instructions in removing and installing the chassis management module CMM from the chassis 1 Remove the CMM from the chassis 2 Install a jumper on pin J1101 3 Reinstall the CMM into the chassis and allow the CMM to boot up completely This will change the password back to the default password changeme 4 Remove the CMM from the chassis again 5 Remove jumper that you installed in Step 2 6 Reinstall the CMM into the chassis 7 Use the password changeme when logging back into the CMM ILOM URL Clarification for Integrated Lights Out Manager ILOM Administration Guide 6596617 In the Integrated Lights Out Manager ILOM Administration Guide for the Sun Blade 6000 Modular System 820 0052 10 there are several references to the following command load source URL The URL used in this command must
29. ng component information Y View Component Information Using the CLI 1 Log in to the ILOM CLI as an Administrator or Operator 2 At the command prompt type gt show CH The manufacturing part number will be displayed in the tru par t number field If the part number is 541 3789 0x the upgraded PCIe 2 0 midplane is installed If the part number is 541 1983 0x the previous version of the PCIe midplane is installed Y View Component Information Using the Web Interface With ILOM 2 x 1 Log in to the ILOM web interface as an Administrator or Operator 2 Select System Information gt Components The Component Management page appears 3 Click on CH in the Component Management Status table A dialog box appears with information about the chassis The midplane manufacturing part number will be displayed in the fru_part_number field If the part number is 541 3789 0x the upgraded PCIe 2 0 midplane is installed If the part number is 541 1983 0x the previous version of the PCIe midplane is installed Sun Blade 6000 Modular System Product Notes August 2009 Y View Component Information Using the Web Interface With ILOM 3 x 1 Log in to the ILOM web interface as an Administrator or Operator The first screen displayed is the Chassis View 2 In the Chassis Inventory table the information for the chassis is displayed in the CH row The midplane manufacturing part number will be displayed in the P
30. ool the power supplies the power supply fans also cool the PEMs slots Note Only force PSU fans to low speed if half the PEM slots or fewer are in use If you enable both this policy and Force Power Supply fans to highspeed high speed dominates Upgraded Midplane Available A midplane upgrade kit is now available for the Sun Blade 6000 modular system The upgraded midplane supports PCle 2 0 compliant server modules The midplane upgrade kit includes a PCIe 2 0 midplane that can be installed in the current chassis The manufacturing part number for the upgraded midplane is 541 3789 For instructions on installing the midplane see the Sun Blade 6048 Modular System Service Manual at http docs sun com app docs prod blade 6000mod You can still install modules including blade modules NEMs and PCIe EMs that are PCIe 1 x compliant into the PCIe 2 0 midplane These modules will work the same as they did with the PCIe 1 x midplane but they will not have the full PCIe 2 0 functionality Refer to the module documentation to determine which modules are PCIe 2 0 compliant Chapter 2 Hardware Notes and Issues 7 Identifying the PCIe 2 0 Midplane To determine which midplane you have installed in the chassis check the FRU ID information through the ILOM CLI or Web interface Use the procedure appropriate for the ILOM interface that you are using See the Sun Integrated Lights Out Manager User s Guide for more information on viewi
31. ork might be slow when both CMM gigabit Ethernet ports are connected to the same network switch PSU I_12V Sensor Reads 2 5 Amps Instead of 0 When Power Cord is Unplugged 6516034 This issue was fixed in ILOM 1 1 6 When the power chords to PSO is removed the CMM I_12V sensor on S1 side reads 2 5 Amps On the 50 side it correctly reads 0 Amps Workaround You can safely ignore these readings BMC Stops Responding and the CPLD Version Displays as 0 0 6517737 This issue was fixed in ILOM 1 6 6 The BMC might intermittently stop responding and the CPLD version displays 0 0 If this issue should arise you should perform the following steps Workaround m Reset the service processor m Retry the ILOM flash upgrade m Power on the server Chapter 3 ILOM Notes and Issues 27 28 Sun Blade 6000 Modular System Product Notes August 2009 CHAPTER 4 Documentation Issues This chapter describes issues related to the Sun Blade 6000 modular system documentation Incorrect Directory for DHCP IP address in Getting Started Guide 6589651 In the Sun Blade 6000 Modular System Getting Started Guide 820 0427 10 page 5 the directory shown for accessing the DHCP IP address is incorrect Step 5 in the Using DHCP to Initially Assign All IP Addresses section and Step 3 in the Assigning a Static IP Address to a CMM Through a Serial Connection section incorrectly state that the network directory for the CMM is CH
32. shutdown of the system The CMM will attempt to contact all the server modules and shut them down gracefully If it cannot shut the server modules down it reports back an error m stop CH force This command causes a forced shutdown which is the same as the ILOM 2 0 3 1 version of stop CH Chapter 3 ILOM Notes and Issues 15 16 Issues Specific to ILOM 2 0 3 1 The issues in this section are specific to the ILOM 2 0 3 1 on the Sun Blade 6000 modular system FRU ID Data Correction for ILOM 2 0 3 1 6631275 Software 1 1 for the Sun Blade 6000 modular system contains a build of ILOM 2 0 3 1 with a serious bug Upgrading to this ILOM version causes some FRU data to be lost Because of this Software 1 1 has been withdrawn and replaced by Software 1 1a If you have not yet upgraded to the ILOM provided with Software 1 1 this issue does not affect you Simply discard any copies of Software 1 1 and obtain Software 1 1a which contains ILOM firmware with the fix If you have upgraded to the ILOM provided with Software 1 1 you must install the ILOM firmware provided with Software 1 1a Doing so will both remove the bug and recover some of the FRU data that was previously not viewable The remaining FRU data must be re entered manually Caution If you have installed the ILOM firmware included in Software 1 1 do not downgrade to an older version of the ILOM firmware Doing so will prevent any of the lost data from being recovere
33. sk you can manually edit the conf interfaces file via the sunservice account or by using the Linux ifconfig command ifconfig ethO netmask AA BB CC DD where AA BB CC DD is the desired subnet mask for example 255 255 0 0 Stop Start and Reset Commands are Disabled for the Virtualized NEM in the Sun Blade 6000 CMM 6813859 and 6812683 This issue was fixed in ILOM 3 0 3 32 The stop CH NEMx start CH NEMx and reset CH NEMx commands for the Sun Blade 6000 Virtualized Multi Fabric 10 GbE NEM Virtualized NEM have been disabled in the CMM Sun Blade 6000 Modular System Product Notes August 2009 Caution Do not attempt to reset the Virtualized NEM SP as it can cause a reset of the entire NEM which disrupts host operation for all blades using the NEM Issues Fixed in ILOM 2 0 3 10 Power LED Does Not Display Until SP Boots 6464862 This issue was fixed in ILOM 2 0 3 10 The front panel power LED does not power on immediately Workaround ILOM service processor bootup sequence takes approximately one minute You should wait for this boot process to complete then reexamine the LEDs Issues Fixed in ILOM 2 0 3 3 SNMP Trap Destination Port Should Be Configurable 6654887 This issue was fixed in ILOM 2 0 3 3 It should be possible to specify per alert rule what the destination port of the trap should be Currently it is hard coded The stop CH Command Lights the Chassis Alert LED 6678328 This issue
34. ted Lights Out Manager ILOM Documentation You will need to reference specific documentation for the ILOM depending on what ILOM version you are using m If you are using ILOM version 1 x refer to the Integrated Lights Out Manager ILOM Administration Guide for the Sun Blade 6000 Modular System m If you are using ILOM version 2 0 refer to the Integrated Lights Out Manager 2 0 User s Guide a If you are using ILOM version 3 0 refer to the Sun Integrated Lights Out Manager ILOM 3 0 Documentation Collection Both documents are posted on the product documentation site http docs sun com app docs prod blade 6000mod Power Supply Module Rating Incorrect in Some Documentation Some of the Sun Blade 6000 modular system documentation states that the power supply modules are rated at 6000W The correct wattage is 5600W Supported Racks List Is Incorrect in Installation Guide The list of racks that support Sun Blade 6000 modular system is incorrect in the Sun Blade 6000 Modular System Installation Guide 820 0050 10 page 5 of the PDF version The Sun StorEdge 72 inch expansion cabinet is not supported for Sun Blade 6000 modular system installation This will be corrected in a future version of the document 32 Sun Blade 6000 Modular System Product Notes August 2009
35. to be lost m Product Part Number m Product Serial Number m Chassis Serial Number You can recover the Product Part Number and Product Serial Number by installing the ILOM firmware provided with Software 1 1a If you downgraded the ILOM after observing the problem Product Part Number and Product Serial Number must be re entered manually The Chassis Serial Number will not be recovered with the Software 1 1a update and must be re entered in any case Follow these steps to re enter the lost FRU data 1 Use SSH to log in to the sunservice ILOM account From the Solaris or Linux command line ssh 1 sunservice ipaddress where ipaddress is the Service Processor IP address 2 Enter one of the following commands a If you only need to re enter the chassis serial number enter servicetool fru_chassis_serial_number s If you need to re enter all three corrupted FRU values enter servicetool fru_product_part_number fru_product_serial_number fru_chassis_serial_number 3 Enter the FRU ID numbers when prompted Chapter 3 ILOM Notes and Issues 17 General ILOM Issues The following issues are not specific to one ILOM version ILOM Service Processor SP Lockup 6471005 The ILOM service processor may in rare circumstances stop responding on serial management port You can avoid this issue by choosing one of the following workarounds to reset and restart the service processor m Use the ipmitool BMC reset cold subcomman
36. was fixed in ILOM 2 0 3 3 When using the stop CH command the chassis Power OK LED goes into standby state and the chassis alert LED is also lights This will only happen if the stop CH command is successful If the graceful shutdown does not occur the alert LED will not light Chapter 3 ILOM Notes and Issues 23 24 LED Test Mode Causes An SEL Message 6713569 When running a test on a Sun Blade 6000 Disk Module or Sun Blade 6000 Multi Fabric Network Express Module a message similar to the following is displayed in the SEL 8e00 06 11 2008 14 19 49 Module Board neml state Transition to Degraded 8 00 06 11 2008 14 20 01 Module Board neml state Transition to Running These messages can be safely ignored Issues Fixed in ILOM 2 0 3 2 ILOM Reports Different Status Value When PSU is Removed 6530748 This issue was fixed in ILOM 2 0 3 2 When a power supply unit PSU is removed from the chassis the PSU status might report different values in the CH PSN ILOM CM CLI objects Workaround If a power supply is removed and you receive a report of different PSU status values you can safely ignore information displayed in the CH PSN ILOM CM CLI objects DC Output Power Supply Issue Fixed in ILOM 2 0 3 2 6664200 This issue was found in ILOM 1 1 6 and fixed in ILOM 2 0 3 2 CMM ILOM service processor provides monitoring and management of chassis power supplies In certain circumstances the power
37. xed in ILOM 2 0 3 10 Sun Blade 6000 Chassis SW 2 1 Power LED Does Not Display Until SP Boots 6464862 on page 23 Fixed Yes Fixed in ILOM 2 0 3 3 Sun Blade 6000 Chassis SW 2 0 SNMP Trap Destination Port Should Be Configurable 6654887 on page 23 Fixed No The stop CH Command Lights the Chassis Alert LED 6678328 on page 23 Fixed No LED Test Mode Causes An SEL Message 6713569 on page 24 Fixed No Fixed in ILOM 2 0 3 2 Sun Blade 6000 Chassis SW 1 2 ILOM Reports Different Status Value When PSU is Removed 6530748 on page 24 Fixed Yes DC Output Power Supply Issue Fixed in ILOM 2 0 3 2 6664200 on page 24 Fixed No Fixed in ILOM 2 0 3 1 Sun Blade 6000 Chassis SW 1 1a Fan Thresholds Not Read by the CMM and Blades 6513836 on page 25 Fixed No Removing a Fan Logs Assert and Deassert Events in CMM SEL 6514930 on page 25 Fixed No CMM NET MGT 1 Port Disabled 6521145 on page 25 Fixed No Chassis Reports as Powered on When Powered Off 6531040 on page 26 Fixed Yes SP Allows One CLI Session 6540550 on page 26 Fixed Yes Fixed in ILOM 1 1 6 Sun Blade 6000 Chassis SW 1 0 Two Connected CMM Gigabit Ethernet Ports Causes Slow Network 6498417 on Fixed No page 27 Sun Blade 6000 Modular System Product Notes August 2009 TABLE1 Sun Blade 6000 Modular System Issues Workaround Issue Status Available PSU 1_12V Sensor Reads 2 5 Amps Instead of 0 When Power Cord is Unplugged
Download Pdf Manuals
Related Search