Coffee Maker Senseo HD7824/50
Contents
1. the Senseo will start automatically the pump to fill the boiler When the boiler is filled the pump stops pumping Pump time approximately 22 seconds procedure To SET the Boiler_empty_flag can be done by cord of the appliance The main switch LED will blink very rapidly for approximately 1 second When the filling procedure has been successful the software will clear a Boiler_empty_flag in the Eeprom By means of this Boiler_empty_flag the system knows the boiler is filled or not To check if the Boiler_empty_flag is really set you should the main switch The main switch LED should light continuously When the Senseo is switched off or disconnected from the mains the value of the Boiler_empty_flag is stored in the Eeprom chip GO SG WN AG NH 2 changed 4222 259 37060 4222 259 37070 4222 247 42550 4222 247 48190 4222 259 37920 4222 240 05940 4222 247 41860 4222 247 47970 4222 247 41950 4222 247 06810 4222 240 05990 4222 247 41920 4222 259 34970 4222 259 35440 4222 247 06840 4222 247 06860 4222 247 35880 4222 247 05130 4222 259 35500 4222 259 36500 4222 247 45890 4222 247 45780 4222 247 05180 4222 247 35870 4222 247 39890 4222 247 05110 4213 247 05250 4222 259 36630 Padholder 1 cup Soft grey Soft grip Padholder 2 cup Soft grey Soft grip Collector Black Spout cover Soft grey Spout assy Silver grey Driptray cover Driptray Black Lever Soft grey Pushrod Se2. Coffee Maker Senseo Service HD7824 50 Service Service Philips Domestic Appliances and Personal Care erviceManua PRODUCT INFORMATION TECHNICAL INFORMATION This product meets the requirements regarding Voltage 220 240 V interference suppression on radio and TV Frequency 50 60 Hz After the product has been repaired it should function Power consumption 1450 W properly and has to meet the safety requirements as Sandby Gosi OW officially laid down at this moment Contents reservoir 1200 cc Colour setting Chrome Silver Sap coding HD7824 50 Water level sensor S2 Water level Temp sensor S1 Sensor CONTROL PCB Push buttons Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands Copyright reserved Subject to modification PHILIPS 08 01 DISASSEMBLY AND RE ASSEMBLY ADVISE To remove the back cover follow below steps Remove Screw A see exploded view Remove valve outlet Start at the upper side of the back cover and stick a screwdriver into the 2 snap locks positions and gently pull the back cover from the appliance so that a little chink between back cover and brew chamber becomes visible Put the screwdriver into the 4 rectangular holes snap locks at the back and gently pull the screwdriver such away that the lips of the snap locks are bent outwards If all clicks positions are loose it is possibl
3. aling ring Ejector p n Distribution disk Black 3 Way valve Boiler assy V7 0 230 V Hose O ring pump elbo Pump Elbo O ring NTC NTC assy Water tank assy TOP Valve outlet Back cover WC sealing Filter WC socket hard Corrugated tube Foot Lid Soft grey Soft grey Soft grey Keep the 1 cup button pressed while plugging in the power reconnect the power cord a second time to the net and push 3 5 HD7824 50 EXPLODED VIEW HD7824 50 EXPLODED VIEW a Q vV amp i
4. e sure the boiler is filled properly other wise perform fill procedure see DFU for instructions 2 Switch appliance on and wait until the unit is ready to brew 3 Be sure a pod holder is placed but without a Coffee POD Only adjusting with plain water 4 Place a cup on the drip tray cover and push the one cup button 5 When the appliance has finished it is stabilized to perform the volume adjustment 6 Empty the cup podholder and push again for one cup setting measure the volume output with a graduated beaker In the table you can find the requirements for the minimum maximum volume output cc mL values depending from the country version Min water cc mL Max water cc mL Unplug the appliance from the mains 8 Press the 1 and 2 cup button simultaneously and plug the mains on 9 When above step succeeded the LED will turn on continuously 10 Depending if the volume has to de or increase you have to push the 1 or 2 cup button Every time you push the 1 or 2 cup button the LED will turn off for 0 5 second feedback to user and the pump time will be shortened or lengthened for 0 5 seconds depending which button was pushed Pushing 1 cup button pump time will be shorten with 0 5 sec is approximately 3 5 cc mL less coffee Pushing 2 cup button pump time will be lengthen with 0 5 sec is approximately 3 5 cc mL more coffee When the volume has to increase with 10 cc for example push the 2 cup but
5. e to remove the back cover Reassemble follow steps backwards To reach the components placed on the base for example exchange the NTC temperature sensor follow below steps First remove back cover brew chamber 3 way valve and boiler Remove both Torx T15 screws B see exploded view Bend the 2 click snap locks with a screwdriver see base the housing can now be removed To remove the rest of the housing unlock the last 4 snap locks at the base and gently pull of the front cover To reassemble follow above steps backwards OPTIONAL accessories No specific issues REPAIR INSTRUCTION Descaling Regular descaling will prolong the life of your appliance and will guarantee optimal brewing results for a long time Follow the steps in the section headed Preparing the appliance for use see DFU Direction for Use manual Instead of only water use a mix of water and Lemon sour For the best result leave the mix of water and Lemon sour for about 30 Minutes in the appliance before you start with flushing the appliance To get the best results repeat above mentioned step once or twice When finished flush the appliance twice by repeating the above mentioned steps only use water instead HD7824 50 Volume adjustment The new PCB circuit board makes it possible to adjust the volume output by means of pushing the one cup and two cup user controls How to adjust the volume output 1 B
6. ton 3 times The new value will be stored when you switch the appliance off by pushing the main switch LED will turn off 11 Turn appliance on again and brew one cup measure the volume In case the volume is not within specification repeat steps 6 11 12 End 2 5 REPAIR INSTRUCTION amp PARTS LIST Automatic filling procedure The Senseo PCB contains an automatic filling procedure software routine This fill routine is only meant for back up Normally the consumer has to follow the guidelines stated in the DFU The filling procedure functions as follows The consumer has to fill the water container and has to plug the appliance on the mains When the Senseo main switch has been pushed the main HD7824 50 Restoring the Boiler_empty_flag to production default Some times it is needed that the boiler of the Senseo have to be emptied This for instance in wintertime where the possibility exists that the boiler becomes frozen during transport e g For those occasions it is handy to restore the Boiler_empty_ flag again to production default in the Eeprom Bringing the Senseo back into production status has the benefit the flush routine will be activated automatically when installed by the consumer see topic Automatic filling switch LED will light continuously This is only the case when the Senseo has not finished the filling procedure completely First use When the consumer pushes the one or two cup button
Download Pdf Manuals
Related Search