L42L Altima Illum Kick Plate MASTER
Contents
1. that will extend beyond the outer edge of the Kick Plate 32 Place new Kick Plate into position on the driver side rear door sill and check for Liner tabs best fit Snap in clip 1 ONLY at the rear of the plate Apply minimum 15 Ibs of downward pressure along adhesive strip A for at least 30 seconds Page 15 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION 33 Carefully finish removing the liners from adhesive strips B and C working your way forward along the Kick Plate 34 Carefully remove the liner from adhesive strip D Snap in clip 2 at the front of the plate Apply minimum 15 Ibs of downward pressure along adhesive strips B C and D for at least 30 seconds cy 35 REPEAT STEPS 30 THROUGH 34 FOR Front of vehicle THE PASSENGER SIDE 36 Remove clear protective film from all plates Note Be sure to trim all cable ties Check all wiring Make sure all trim is in place and clips are securely fastened Page 15 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 14 CHECK OUT Inspect the vehicle for unfinished work 1 Open front left door 2 Verify the illuminated Kick Plate turns on 3 Push and hold the door status switch located on the vehicles center pillar The kick plate should turn off within a few minutes 4 Repeat steps 1 4 with the front right door 5 Verify the functional2. C ap T C 9 f Tighten LA i Straight and evenly spaced all around ii Tight and no gap and test the signal Vehicle Harness Accessory harness Page 5 of 17 1 Tap vehicle wire a Remove grey cap slot side from tap body b Slide cap around vehicle wire c Tighten the tap TIGHT with finger pressure NOTE Do not re use the tap for subsequent re installation Figures are not to scale 2 Inspect the tap to ensure correct installation NOTE Avoid putting pressure on the vehicle wire and tap for the remainder of the installation 3 Inspect the tap to ensure correct installation a Remove red cap non pierce side from tap b Remove the protective stub from the wire c Insert wire through the non pierce side opening d Spread the individual strands into fan shape e Insert wire into the tap body and ensure that it is all the way in f Tighten the tap TIGHT with finger pressure 4 Confirm the tapped accessory wire a Inspect the tap to ensure correct installation b Test the signal to ensure that it is working properly 5 Secure the tap a Secure the tapped wire on the non pierce side to the body of the tap with electrical tape 2 revolutions b Secure the body to harness where vehicle wire iS being tapped with electrical tape gt 2 revolutions 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION DRIVER S
3. the wires along the existing harness Secure with cable ties as shown Accessory z ig 12 Locate the driver side Accessory connector plug a Connector plug It will be located up under the dash above the vehicle diagnostic port as shown Carefully pull the plug down for easier access Note Be sure to grab the connector and not the harness when separating the plug from the foam tape Brake Pedal LA I Note A previously installed accessory may r iver footwell be present If so carefully remove the accessory connector harness from the accessory connector plug before posi tapping It is recommended that all posi tapping be completed before reattaching the accessory connector harness to the plug Page 8 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION CAUTION e Color s given in illustration s are for reference only Use location s where color deviates e Ifa vehicle wire is being used by another accessory and a posi Tap is present tap the accessory wire NOT the vehicle wire Fig 13 13 Using a posi tap connect the Black wire from the Kick Plate to the Yellow wire on the Accessory Connector Harness Part 999Q9 AY000 dd Black wire SN Using a posi tap connect the Red wire from the Kick Plate to the Pink wire on the Accessory Connector Harness Note Be sure NOT to posi tap through ge L Shrink the shrink wrap tubing wrap
4. GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION Illuminated Kick Plate Kit 2 APPLI CATION Altima 2013 3 PART NUMBER 999G6 UZO0OO Illuminated Kick Plate Kit 4 KI T CONTENTS item QTY Description Illuminated Front Kick Plates B 2 Non illuminated Rear Kick Plate RH Non illuminated Rear Kick Plate LH D 1 Misc parts kit TOOLS REQUI RED e Trim stick e Protective gloves e Panel popper tool e Electrical tape masking tape e Protective cloth e Alcohol wipes PRE I NSTALLATI ON CAUTI ON NOTES e Dealer installation recommended Instructions may refer to Service Manual e Installation may require special tools e This part is to be installed within a surface temperature range of 60 110 F e nstall one side completely before starting on the other side CAUTION e This accessory must only be installed as specified in these instructions e Ensure at all times that parts are securely fitted and will not compromise the safe function of vehicle systems Page 1 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 7 INSTALLATION OVERVIEW Accessory Lighting Control Connectors Modules Passenger Kick Plates pm Connectors lt Driver Kick Plates 8 CRITICAL STEPS The following steps are critical and must be performed EXACTLY as specified to ensure proper installation Location of the lights must be followed exactly as describe
5. IDE INSTALLATION 5 Carefully pull back carpet edge to expose existing harness and clips Note Manufacturing bar code labels do NOT need to remain on the vehicle Be sure to remove these labels or the Kick Plate adhesive mounting strips may not adhere properly Clean all mounting surfaces with alcohol wipe before final installation 6 Place new Illuminated Kick Plate into position on the driver side door sill and feed the wiring through under the door welt Note Do not snap plate into place at this time 7 Feed the end of the wiring up through the existing harness clips towards the footwell Page 6 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION 8 Carefully flip the driver Kick Plate over Remove backing from five 5 adhesive strips located on the back of the Kick Plate 9 Carefully align Kick Plate with mounting holes and press firmly into position Apply minimum 15 Ibs of downward pressure evenly along the Kick Plate for at least 30 seconds 10 Carefully align Kick Plate and snap into position Remove all slack from the wiring at the plate end Carefully bend the flat wire to fit tightly over the sheet metal edge Flat Wire i L h Kick Plate Page 7 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION 11 Press the door seal welt back down into position Route
6. d in this instruction Posi Tap instructions must be specifically followed as described Be sure to apply masking tape as needed in order to protect any areas that may become scratched or damaged by tools Be sure to apply foam tape to any wiring components that can be damaged over time by sharp edges Test the functionality of the kit before final clean up and reinstallation of interior panels Page 2 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 9 VEHICLE PREPARATION 1 Apply parking brake 2 Confirm the vehicle is no longer in the default shipping state Extended Storage Switch Pulled Up and BCM in Transit Mode Failure to confirm the vehicle has been removed from this state will result in the loss of normal vehicle operation The confirmation requires two checks 2a Locate the Extended Storage Switch 2b Turn the ignition switch from OFF to ON position If in the cabin fuse block Once located turn indicators illuminate for approx 1 minute the check that it is in the Customer vehicle is in shipping mode To exit shipping mode return the ignition switch to OFF position Simultaneously push the wiper and turn signal stalks downward and hold for 2 seconds position See below for reference Inventory Customer n PUSH DOWN OFF Lt LE ss P eels INCORRECT CORRECT NOTE Typical vehicle condition shown here Switch is easily identifiable b
7. dog 999G6 UZ000 II 3 22 2012 Mechanization
8. e the wires on the passenger side along the existing harness and up under the dash Secure any excess wire between the kick plate and the lighting control module with cable ties Note Do NOT secure the wiring to the drain tube in any way Note A functionality test is recommended at this time Refer to Check Out procedure on page 16 Fig 29 29 Reinstall the side trim panels on both sides of the vehicle along the bottom door seals Carpet holes NEN ub m from the seat to the footwell see fig 2 W NN Note Be sure to align the rectangular carpet holes with the harness routing clips Page 14 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION REAR DOORS NON ILLUMINATED 30 Carefully remove the existing kick plate from the driver side rear door rocker area Note Manufacturing bar code labels do NOT need to remain on the vehicle Be sure to remove these labels or the Kick Plate adhesive mounting strips may not adhere properly EX E am RN snm L Clean all mounting surfaces with alcohol wipe before final installation 31 Place the new driver side Kick Plate upside down on a protected work surface Prep for installation as follows 1 Completely remove the liner from adhesive strip A at the rear of the plate 2 On the remaining adhesive strips B C and D partially peel away enough of the liner to fold down a flag
9. here is looking up under the dash at the parking brake pedal 18 Route the wires along the existing harness in the footwell Bundle and secure any excess wire with cable ties as shown On Parking Brake Cable ties B M Driver footwell 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION PASSENGER SIDE INSTALLATION 19 Carefully pull back carpet edge to expose existing harness and clips Note Manufacturing bar code labels do NOT need to remain on the vehicle Be sure to remove these labels or the Kick Plate adhesive mounting strips may not Manufacturing h Iv labels adhere properly SPA e C Clean all mounting surfaces with V EAR Front of vehicle alcohol wipe before final installation 20 Place new Illuminated Kick Plate into position on the passenger side door sill and feed the wiring through under the door welt Note Do not snap plate into place at this time Do not remove clear protective film until procedure is complete 21 Feed the end of the wiring up through the existing harness clips towards the footwell Page 11 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION 22 Carefully flip the Kick Plate over Remove backing from five 5 adhesive strips located on the back of the Kick Plate 23 Carefully align Kick Plate with mounting holes and press firmly into posit
10. ion Apply minimum 15 Ibs of downward pressure evenly along the Kick Plate for at least 30 seconds 24 Remove all slack from the wiring at the plate end Carefully bend the flat wire to fit tightly over the sheet metal edge Flat Wire Kick Plate Page 12 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION 25 Press the door seal welt back down into position Route the wires along the existing harness Secure with cable ties as shown Note Do NOT secure the wiring to the drain tube in any way Harness Cable Tie 26 Locate the passenger side Accessory Connector plug It will be behind the glovebox on the right side as shown in this cutaway view Y Accessory connector plug Passenger Footwell Page 13 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION Fig 27 27 Using a posi tap connect the Black wire Part 999Q9 AY000 from the Kick Plate to the Yellow wire ee on the Accessory Connector Harness Black wire Using a posi tap connect the Red wire from the Kick Plate to the Pink wire on the Accessory Connector Harness Note Be sure NOT to posi tap through Shrink the shrink wrap tubing wrap Plug the Accessory Connector Harness into the vehicle connector plug on the passenger side HARNESS NOT INCLUDED IN KIT Red wire REFERENCE PART NUMBER 999Q9 AYOOO 28 Rout
11. ity of all electrical vehicle components where harnesses were accessed 6 Check and clear trouble codes DTC 7 If this vehicle will be returned to a dealer lot or showroom for an extended period of time be sure the extended storage switch is placed in the inventory position Refer to section 9 Vehicle Preparation 8 If vehicle is NOT going into storage reset the radio presets to the recorded settings Page 16 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 15 BILL OF MATERIALS Illuminated Kick Plate Kit 999G6 UZ000 to Parts Contained in Bag Labelled Installation Kit Qty Part Number PLATE KICKING FR OTR RH 999G6 UZ001 PLATE KICKING FR OTR LH 999G6 UZ002 PLATE KICKING RR OTR RH 999G6 UZ003 6 ACCESSORY WEBSITE ADDRESS PAPER at 999V2AWO00 2 ACCESSORY CONMECIOR HARNESS YOT INCLUDED RKT pey segue _ a a x s U E BOM 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Ki 16 MECHANI ZATION u0 12 310 1q 3 0 3007 Y SSS NS 91 d HIH p euluun I NN x U31IMS 041u02 duue wooy Joueju sadA q31 pue qing 1 sduie 10lI1 1u 3IU A Q q B 0J3Ju02 due soaquy DIU A 2a5e3oA o p pm NN 0 300 J SS 1 ME u 0 53Jeld 41 AZT pajeuiuunjl Janes Auayeg pawl HuU HT1 Auayjeg f p snj ACT STE speo pawl JINGOW Mayeg YA Jeuonippy IOYLNOD A
12. x 3 HARNESS NOT INCLUDED IN KIT TES REFERENCE PART NUMBER Gt 4 T 999Q9 AYOOO QN Shrink wrap Red wire 14 Follow this finishing procedure on all Accessory posi taps Leave a short length of Connector Wire wire extended past the posi tap and bend down as shown Use electrical tape to secure the extra wire against the posi tap with at least two revolutions Electrical tape Note Make sure that the end of the wire is wrap around completely covered by the tape bu twice Shrink wrap ae om end of Wire bent down Page 9 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 13 INSTALLATION Foam taped Connector 3x L RD y vi plug p 3 17 Plug the Accessory Connector Harness into the vehicle connector plug on the driver side Wrap the Connector in foam tape Use a cable tie to secure the Accessory Connector to the existing harness as shown Route above these cables Note The view shown here is looking up under the dash from behind next to the parking brake pedal Foam taped Connector Harness Parking Brake Page 10 of 17 15 Wrap the posi taps with foam tape to prevent rattle 16 Route the wires up under the dash along the existing harness Feed the wires above the hood release and parking brake release cables Use a cable tie to secure the wiring to the large harness loop ahead of the fuse panel Note The view shown
13. y the permanent push pull fuse holder Actual position on the fuse block may vary vehicle to vehicle 3 Record customer radio presets NOTE USE CAUTION WHEN REMOVING RE INSTALLI NG TRIM COMPONENTS TO AVOID DAMAGE SCRATCHES BREAKING OF CLIPS AND OR INTERIOR TRIM PANELS MOVE ALL TRIM COMPONENTS TO A PROTECTED AREA A WARNING Move driver and passenger seats to full back position Disconnect negative battery terminal before proceeding 10 Order of Installation 1 Remove panels and trim Route Wiring 2 Install Kick Plate Assemblies Reinstall all panels Page 3 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 11 INTERIOR PREPARATION existing kick plate from the driver side Wz rocker area x Cy Fig 1 1 Use a trim stick to carefully pry off the d EZR T Fig 2 2 Use a trim stick to carefully pry off the i trim panel along the bottom door seal WS from the back of the seat up to the footwell Note Begin prying the panel off at the rear edge and work forward 3 Carefully pull back the bottom door seal welt 4 REPEAT STEPS 1 THROUGH 3 FOR THE PASSENGER SIDE Page 4 of 17 999G6 UZ000 II 3 22 2012 INSTALLATION INSTRUCTIONS Illuminated Kick Plate Kit 12 POSI TAP INSTRUCTIONS Grey Cap i Straight and evenly spaced all the way around ii Tight and minimize gap wire jacket should be crushed Fig 3 Red
Download Pdf Manuals
Related Search