Home

Specifications

1. If applicable VEHICLE DATA PLATE A permanent plate shall be installed in the Driver s compartment which indicates the following Filter Part Numbers for the Engine Transmission air and fuel systems Serial Number for the Engine and Transmission Delivered Weights of the Front and Rear Axles Paint Code Brand and Code s Body Builder Project Number OVERALL HEIGHT PLATE There shall be a placard located in direct view of the Driver which shall indicate the overall height of the vehicle ACCIDENT PREVENTION There shall be a placard in the cab seating area which reads ALL OCCUPANTS MUST BE SEATED AND BELTED WHEN THE APPARATUS IS IN MOTION PERSONNEL CAPACITY There shall be a placard mounted in the Driver s compartment which specifies the maximum number of personnel the vehicle is design to carry per NFPA standards The placard shall be located in clear view of the Driver ACCIDENT PREVENTION If there is a rear bumper extension of 8 or more there shall be a placard on the rear face of the body in clear sight from the ground which reads WARNING DO NOT RIDE ON STEPS OR DECK AREAS WHILE THE APPARATUS IS IN MOTION DEATH OR SERIOUS INJURY MAY RESULT FRONT BUMPER The front bumper shall be as provided by the cab chassis manufacturer No other alternation or modifications are required SVI 603 03 27 07 Page 31 of 86 Maui Police Department SVI Trucks Production Specification CO 3 BUMPER GRAVELSHIELD The bumper ex
2. The instrumentation system will provide a three second alarm every three minutes for the following situations Low fuel Water in fuel 1 1 Feature only available when optionally equipped 2 Feature only available on engines with preheat capability WHELEN ELECTRONIC SIREN A Whelen WS 295HF82 electronic siren head shall be provided and installed in the center main switch lower panel Location left side of center panel POWER AND GROUND STUDS BATTERY DIRECT Power and grounding studs shall be provided and installed behind the electrical center cover with a breaker The studs shall be 10 and capable of carrying up to a 40 amp battery direct load SUPER AUTO EJECT 20 AMP KUSSMAUL A Kussmaul 20 amp Super auto eject electrical receptacle with a yellow weatherproof cover and box shall be installed on the left side of the cab above the wheel well It shall automatically eject the plug when the starter button is depressed The U L maximum allowable amperage draw on receptacles is generally 80 of their listed rating for example the 20 amp receptacle should not carry more than 16 amp continuous load When adding the different amperage draws of the components being installed on the chassis be sure to factor in whether the components will draw a continuous load or intermittent load Amp Draw Reference List Kussmaul 1000 Charger 3 5 Amps Kussmaul 1200 Charger 10 Amps Kussmaul 35 10 Charger 10 Amps 1000W Engine Heater 8 33
3. SVI 603 03 27 07 Page 27 of 86 Maui Police Department SVI Trucks Production Specification CO 3 HVAC SYSTEM The cab shall be equipped with a ceiling mounted HVAC system The system shall consist of an overhead heater defroster air conditioning unit mounted above the engine tunnel in a central location with dash mounted controls The ceiling mounted HVAC system includes fourteen 14 adjustable louvers Six 6 forward facing louvers for windshield 45 000 Btu s of heat at 460 cfm for defrosting Four 4 rearward facing louvers to direct air for crew comfort and six 6 for driver and officerc comfort In Cabin Mode the system is designed to produce 60 000 Btu s of heat and 32 000 Btu s of cooling The system shall be capable of lowering the cab interior temperature from 100 degrees to 70 degrees within thirty minutes with a relative humidity of sixty percent A roof mounted condenser shall be installed in one 1 of the following locations See attached PDF File for Clarification Flat Roof Pumper Rescue Mid Mount Aerial Centered on cab mid roof Raised Roof Pumper Rescue Mid Mount Aerial Centered on cab forward of raised roof against the slope rise Flat Roof Traditional Aerial LH side of cab mid roof Raised Roof Traditional Aerial LH side of cab mid roof on raised section ww na wna 1 2 3 4 The air conditioning compressor will be an engine driven Seltec TM 16 and utilize R 134A refrigerant The A C lines w
4. 1 005 03 25 05 gt Pricing as of QW Release 03 25 2005 Diamond Flat Floor ELFD 24 Raised Roof Alum Tilt Cab Flat Floor ELFD 24 Raised Roof Tilt Cab DIA GLAD Cab Doors Full Length 20 24 Roof DIA GLAD Door Handles Exterior Chrome With Scuff Plate 4 Front amp Rear Power Door Windows DIA GLAD MET MS Fabric DBP Covered Seats Black Seat Color Seatbelt Warning System Driver Seat Bostrom 8 Way Electric ABTS Officer Seat Bostrom 8 Way Electric ABTS ELFD Compartment Without Interior Access Front Fascia EVOLUTION gt Whelen LED 4x6 Dual Blue Lights on Fascia Below light to be super LED blue gt Headlights w Daytime Running Lights amp TurnSignals Front Grille Stainless Flat Hinged GLAD Evolution DIA GLAD Mirror Ramco Bus Style Remote Heated 2 9000 FFHR 800HR gt Cab Crash Test ECE 29 DIA GLAD Chassis One Year Warranty Cab Perforation Ten Year Warranty Frame Paint Standard Black gt Wheelbase 238 gt Double Rail High Strength Frame 0 38 Max Height of Vehicle 135 From Ground gt Fuel Tank 68 Gallon 42 Min A E ADV DIA GLAD MET MS Front Bumper w 6 Extension DIA GLAD gt Air Horn Grover 21 DRV amp OFF Inboard 2 Air Reservoir Air Horns 1200 Cu In oO O N N oO O Oa aa EO HSH ASH O M i i a i O OONA BW w w ooocoooooooNN ot oo 03 27 2007 PART NO 03 20 5000 03 25 1700 03 35 0500 03 40 1400 05 18 1400 06 31 1700 05 50
5. 3 Maui Police Department members for a final inspection of the completed apparatus SHIPPING INSTRUCTIONS The unit shall be delivered to a west coast port in preparation for ocean freight shipment to Kahului Maui Hawaii Only roll on roll off type shipping is acceptable NO container or rack type shipping is allowed for this unit The preferred location is below the main deck or located under an overhang for protection from salt spray If the unit is not shipped on a lower deck the entire unit SHALL be shrink wrapped and taped off at the lower body to protect the unit from salt spray SVI 603 03 27 07 Page 6 of 86 Maui Police Department SVI Trucks Production Specification CO 3 DELIVERY AND DEMONSTRATION The contractor shall be responsible for the delivery of the completed unit to the Maui Police Departments location On initial delivery of theapparatus the contractor shall supply a qualified representative to demonstrate the apparatus and provide initial instruction to representatives of the Maui Police Department regarding the operation care and maintenance of the apparatus and equipment supplied at the Maui Police Departments location The delivery engineer shall set delivery and instruction schedule with the person appointed by Maui Police Department After delivery of the fire apparatus the Maui Police Department shall be responsible for ongoing training of its personnel to proficiency regarding the proper and safe use of the appa
6. Awning hangers Built in awning tie downs to hold awning steady in a breeze Durable multi layer laminated vinyl fabric that resists scratches stains fading and mildew Alumaguard metal wrap cover EXTERIOR REMOVABLE DESK A removable desk shall be provided stored in exterior compartment and capable of being mounted to side of body adjacent to patch panel compartment Desk shall be fabricated of smooth aluminum with grey hammertone powder coated finish EXTERIOR DRI ERASE BOARD Three 3 removable dri erase boards shall be provided that attache to side of body in the following locations one 1 above generator compartment C4 area and two 2 located at curbside slideout one 1 each side of slideout compartment SVI 603 03 27 07 Page 50 of 86 Maui Police Department SVI Trucks Production Specification CO 3 WALK IN INTERIOR FEATURES MAGNETIC WHITEBOARD There shall be wall mounted magnetic whiteboard surfaces located in the walkin interior body where ever possible and practical CAB BODY WALK THROUGH CONNECTION The front center of the rescue body shall be interconnected with the rear crew area of custom cab through a weather tight walk through opening The opening shall be designed to allow the custom cab to tilt forward without disconnecting an attached type seal between the cab and body The opening shall be approximately 24 wide x 70 high sized to match the cutout in the rear wall of the cab The front of the body shal
7. Each light shall have a blue LEDs with clear lens and a chrome finished flange ZONE C REAR WARNING LIGHTS There shall be two 2 Whelen 600 series 6 x 4 LED lights provided on the rear face of the apparatus one 1 each side near the corners Each light shall have a blue LEDs with clear lens and chrome finished flange The lights shall be switched at 12 volt control panel in cab SVI 603 03 27 07 Page 68 of 86 Maui Police Department SVI Trucks Production Specification CO 3 LINE VOLTAGE SYSTEM DIESEL GENERATOR One 1 Onan CMQD model 12 0 HDKCD 12 000 watt 120 240 Volt 100 50 amp 60 Hertz electrical generator with electric start shall be provided Generator shall be capable of operating approximately 6 hours full load on 13 gallons of fuel Generator shall be equipped with low oil shutdown Generator starting system shall be wired to chassis battery system with heavy duty stranded copper cables Fuel system shall be modified with addition of an electric fuel pump and plumbed to chassis fuel system The exhaust shall be piped to the roof of body GENERATOR MOUNTING The generator shall be mounted on rubber vibration isolators The compartment shall be reinforced where necessary to hold weight of generator Generator shall be installed over a stainless steel drip pan with a 1 lip to retain any spillage of oil or fuel A valve shall be located at generator oil drain outlet and shall be piped to underside of generator
8. Take down Blue Linear LED Whelen 9592 Opticom emitter Blank Blue Linear LED Clear Halogen Take down Clear Linear LED Blue Linear LED Clear Clear Clear Clear Clear Clear Clear Clear Clear Clear One 1 Blue Linear LED Side Facing Clear One 1 Blue Corner LED The lightbar shall be separately switched at the 12 volt control panel LENS COLOR All clear lights shall shut down when the parking brake is set to comply with Blocking mode requirements as outlined in NFPA 1901 SVI 603 Page 66 of 86 03 27 07 Maui Police Department SVI Trucks Production Specification CO 3 ZONES B AND D SIDE WARNING LIGHTS There shall be two 2 Whelen 900 series 9 x 7 surface mount LED lights provided one 1 on each side of the apparatus in the upper rearward corners Each light shall have a blue LEDs with clear lens and chrome finished flange The lights shall be switched at 12 volt control panel in cab There shall be two 2 Whelen 900 series 9 x 7 surface mount LED lights provided one 1 on each side of the apparatus in the upper forward corners rearward corners of the Spartan cab Each light shall have a blue LEDs with clear lens and chrome finished flange Lights shall be located on the rearward upper corners of the Spartan cab The lights shall be switched at 12 volt control panel in cab ZONE C REAR WARNING LIGHTS There shall be two 2 Whelen 900 series 9 x 7 LED lights provided
9. The opening shall be capable for use as an escape hatch ventilation and supplemental light in the interior of the body The opening shall be approximately 26 x 26 in size and equipped with a 3 16 aluminum door with 1 8 brushed aluminum interior box pan The opening shall be framed with a raised 1 lip to prevent water from entering the opening and a weatherproof gasket The door shall flange down around the roof framing and slope forward so as not to hold water A interior 1 4 turn butterfly type latch shall be provided to hold hatch closed One gas piston type door check to hold door in open position and that can be closed without unlatching shall be bolted to opening frame and door box pan The hatch shall be specially reinforced for the installation of a large skylight The skylight shall be 20 x 20 in size with clear 1 4 Lexan or safety glass panel The roof skylight shall be mounted in standard automotive rubber window mounting and shall be completely weatherproof and watertight SLIDING POCKET DOOR There shall be two 2 sliding pocket doors provided on interior of walk in body area Pocket doors shall be fabricated from 1 8 smooth aluminum and be approximately 1 1 2 thick and hang on adjustable pocket door hardware The doors shall be painted to match the interior wall color A stainless steel handle shall be provided on each side of door The doors shall be equipped with a pneumatic cylinder which will over center to hold the door
10. There shall be color coded LED indicator lights provided to indicate the status of each branch breaker Each individual switch and all meters shall be back lit for identification in low light situations The panel shall have two 2 meters one 1 to monitor frequency and one 1 hour meter to register genset run time Each circuit breaker shall be hydraulic magnetic trip free style with a manual reset The Paneltronics panel shall also control the automatic cut over for switching the apparatus from shore to generator power The entire panel shall be mounted to a recessed box The front panel shall be mounted to the box via a vertical piano style hinge that allows the front panel to open for access to the breakers SVI 603 03 27 07 Page 70 of 86 Maui Police Department SVI Trucks Production Specification CO 3 SHORE POWER RECEPTACLE Two 2 30 ampere 120 volt single phase shore power receptacle s shall be provided on the apparatus to provide an external power source for apparatus electrical circuits A matching 30 ampere plug shall be shipped with the apparatus for Fire Department supplied external power source wiring Shore power shall be wired to the specified 120 volt 20 ampere electrical circuits on apparatus maximum four 4 circuits Circuits shall be provided with circuit breaker protection with either generator or shore power providing power To protect both the generator or external power source from backfeed a 120 volt 25 a
11. 00 0100 P3 10 0500 P1 50 1100 AO A0 1010 AO A0 1110 AO V1 8100 A0 W0 3000 A1 30 1100 CZ 10 2810 CZ 30 5100 CZ 32 1110 CZ 32 1230 CZ A0 1010 NO A2 1310 A2 30 1100 CZ 10 2810 CZ 30 5100 CZ 32 1110 x x D2 WX X 25 DESCRIPTION Whiteboard Magnetic Mid Atlantic MRK 24 space 19 Data Rack Telex Dispatch System Interior Cabinet Overhead 24 48 w 11 16 h Interior Cabinet Sliding Aluminum Doors Rear Cab Desk L Shaped Aluminum 120 Volt Electrical Outlet Location Only Interior Seat Indiv Pedestal Black Interior Seat Safety Belts Fuel Fill Door Cast Aluminum Streetside W W Dri Erase Marker Magnetic Board Slide Out Pencil Drawers Keyless Remote Entry System Intercom System Sigtronics 4 Position Equipment to be provided by customer Harmer Communication BODY BODY 22 Walk In MATERIAL 3 16 aluminum BODY ROOF 3 16 smooth aluminum SUBFRAME 2 x6 x1 4 Alum Tube MOUNTING Spring Mounts 6 alum REAR BUMPER 17 Aluminum Body Rear Tow Eyes 2 Painted Below Body subframe No Trailer Hitch Receiver Body Fender Panels 1 8 Smooth Aluminum Wheel Well Opening Edge Die Formed No Wheel Well Liners NO SCBA Fender Comp ts PAINT Aluminum Body Paint Body Single Color Paint Body Color Coat Clear Coat Paint Warranty 7 year Body Undercoating Undercoating Warranty Reflectiv
12. 1 0 0 4 1 1 1 1 1 1 1 3 1 1 1 03 27 2007 PART NO FOQ C0 A050 FO D0 1000 FO D0 1010 FO E0 A010 FO FO 1010 FO FO 1012 KO BO 1110 EF A0 1410 K0 E0 0740 K0O X0 0100 MA 01 0320 MA 22 1320 MA 10 1320 MD 80 2000 FQ 50 1130 FQ 50 2110 FQ 50 2120 MB 20 1110 MB 22 1200 MB 23 1200 MB 20 1310 MB 22 1400 MD 20 2000 MD 20 3021 MD 50 9000 FQ 20 1320 FQ 15 1210 MB 22 1602 FQ 20 1420 FO 15 1310 MD 50 2000 FQ 50 1130 FQ 50 2110 FQ 50 2120 MB 20 1310 MB 22 1400 MD 20 2000 MD 20 3021 MD 50 9000 MD 52 0100 F0 30 1320 F0 15 1210 MB 22 1602 F0 30 1420 F0 15 1310 ZZ 10 1000 MD 20 3000 MD 50 2000 MD 51 0100 MD 52 0100 NO 10 A200 NO 11 2140 NO 11 6110 NO 11 A120 NO 18 1200 NO 18 2100 NO 18 3100 S lt DESCRIPTION Cab Chassis Mfg Cut Out in Rear Cab Wall Interior Cab and Body Window Covers Wnidow Cover Ties Roof hatch 26x26 aluminum with skylight Interior Sliding Pocket Door Pocket Door Audible Seal Entry Door Side of Body Single Door Handrails Entry Door Window 18 w x 22 h Vertical Sliding Entrance Door Swing Down Body Entry Steps Interior Finish FRP white pebble grain Full Height 21 26 Walk in floor Loncoin ll Black Onyx WI 21 26 Underfloor Material 3 4 Marine Plywood WI 21 26 Air Conditioning System STREETSIDE INTERIOR AREA Slide Out Command Wall 124 5 S2S Window 18Wx22H sliding Front Window 18Wx2
13. 10 days notice before cancellation must cover all operations of the Contractor or anyone employed by any of them GENERAL CONSTRUCTION AND DESIGN The design of the equipment shall be in accordance with the best engineering practices The equipment design and accessory installation shall permit accessibility for use maintenance and service All components and assemblies shall be free of hazardous protrusions sharp edges cracks or other elements which might cause injury to personnel or equipment All components shall be designed and protected so that heavy rains or other adverse weather conditions will not interfere with normal servicing or operation All oil hydraulic and air tubing lines and electrical wiring shall be located in protective positions properly attached to the frame or body structure and shall have protective loom or grommets at each point where they pass through structural members except where a through frame connector is necessary The apparatus shall be designed and the equipment mounted with due consideration to distribution of load between the front and rear axles so that all specified equipment including personnel will be carried without injury to the apparatus All dimensions are approximate and subject to a plus or minus 1 4 tolerance The following specifications describe minimum requirements for an emergency services vehicle designed for severe duty applications The materials specified are considered absolute mi
14. 1030 R5 52 1021 R5 52 1022 lt DESCRIPTION Exterior Outlets 120V 2 Body Fenders straight Straight Blade 120 Volt 15 Amp Exterior Outlets 120V 2 Rear of Body straight Straight Blade 120 Volt 15 Amp Interior Outlet walk in 120V straight Straight Blade 120 Volt 15 Amp Interior Outlets 120V 4 outlet strip Interior Lights 120V recessed ceiling fixture Interior Lights 120V above counter fixture Generator Onan 8 kW Diesel Liguid Cooled Generator Mount In Compartment Generator Fuel Chassis Fuel Connections Generator Battery Chassis 12 Volt Connection Generator Cooling Radiator Generator Exhaust Generator Manuals Generator Insulation Sound Thermal Generator Gauge Panel Generator Control Remote Control in Cab Inverter Xantrex Prosine 3 0 w ACS Remote 3000 watt 120 240 Volt Wiring System Walk in Wiring Walk in Labeling of Equipment Electrical Wiring Schematic 120 240 Volt Scene Lighting Scene Lights on the Front of the Cab gt Fire Research FCA800 S50 500W 120V Focus Make Fire Research Model Focus P N FCA800 S50 Switch In Cab Scene Lights in the Side Upper Body Side Upper Streetside gt Fire Research FCA200 S50 500W 120V Focus Make Fire Research Model Focus P N FC200 S50 Switch On Body one each side Side Upper Curbside g
15. 1500 06 50 2100 06 50 3000 06 50 3500 06 60 1500 05 30 5000 06 50 4500 06 70 0100 07 24 0500 07 32 0200 07 35 1000 07 36 1000 08 11 2700 08 50 1600 08 50 3000 09 24 AG00 11 10 0500 07 32 0500 08 50 4000 09 75 0500 11 15 1000 11 20 1000 11 30 0500 11 30 3500 11 40 0500 11 40 3000 12 18 0800 11 50 1400 12 22 3000 12 25 2200 12 30 1200 12 50 1500 13 10 0600 13 10 1000 13 20 1100 14 10 0200 13 10 3100 14 20 9000 14 25 1000 14 50 1100 28 10 4000 15 20 1100 28 10 32AA 12 23 0100 12 25 2600 12 50 2500 12 50 3000 13 50 4500 14 25 0300 14 30 0500 15 05 0600 15 10 4200 15 10 4600 15 10 4700 15 10 4400 15 05 3000 15 10 0500 15 10 3800 S X DESCRIPTION gt Bumper Apron 6 Extension DIA GLAD gt Tow Eyes Chrome Plated Thru Bumper Air Horn Actuation Steer Wheel amp OFF Foot Switch gt Speakers CPI 100W Driver amp Officer Side Outboard 2 Front Axle 18000 ArvinMeritor ADV DIA MET gt Michelin XZA1 315 80R22 5 9 00F 18000 ADV BE DIA GL4 MET MS Cramp Angle Frt Axle MFS 18 50Deg 315 80R Tires Wheels Front Alcoa Polished Alum 9 00 x22 5 Wheel Bearings Front Oil Lubricated Front Shock Absorbers Bilstein Brakes Front Disc Type w Auto Slack Adjust Chassis Alignment Steering Column amp Wheel Tilt Telescopic Type Front Mud Flaps Rear Axle 24000 ArvinMeritor RS 24 160 ADV DIA GLAD MET Top Speed 65MPH 2MPH Brakes Rear 16 5 x7 S Cam Single Axle Brakes ABS Wabco Front
16. 40 5500 19 50 4000 19 50 6300 22 06 1000 18 07 0200 19 10 1100 19 15 2000 19 15 41AA 22 05 0700 22 10 2000 22 20 1300 22 20 4000 23 05 1000 23 05 2600 23 15 1000 23 20 1000 24 10 0500 27 10 0500 27 10 3000 28 10 0500 28 10 1800 28 20 0500 28 20 1000 30 10 1500 03 SV 1100 03 SV 2100 03 SV 8100 10 00 0130 10 10 1130 10 10 1310 10 11 1110 10 25 1110 10 A5 1110 10 AA 1210 10 AA 1310 10 C0 0100 10 C6 1000 10 HA 3010 10 HA 3012 10 K0 0100 10 S1 1100 10 S3 0138 10 S8 0400 10 S8 0400 XS Cab Interior Red White Dome Lighting 5 Std BE DIA GLAD Door Ajar Light Red Flashing Std Engine Tunnel Work Light 1 Dome Lamp Clear 7 Dome Lamp Activation Push Button amp Any Door Map Light Roxter Gooseneck RH Dash Radio Weather Band AM FM Stereo with CD Player Camera Dual Rearview w Display on Vista Screen DIA GLAD Dash and Header Trim ABS DIA Inner Door Panels ABS DIA Engine Cover Fixed Type Xtreme Duty DIA MDT Provision ABS Int DIA GLAD Center Console Paint Interior Silver Gray Zolatone Texture Finish Interior Trim Color Gray SoftVinyl Gray ABS Blk FloorMat HVAC System Ceiling Mtd w Roof Mtd Condenser Insulation Package Deluxe Cab Tilt Actuation DIA GLAD MET MS Receptacle Cab Tilt Control on Frt Bumper Tail Rear Cab Wall Cut Out 24 x72 Wheel Well Liners Full S S ADV DIA GLAD MET MS Assist Handle Ext Cab 18 SS 3 Cab Paint Single Color Exterior Paint brand and color Finish Base an
17. A0 1010 CZ A0 2420 NO A2 1210 B5 30 1100 10 S5 0140 CZ 10 2910 CZ 30 5100 CZ 32 1110 CZ 32 1230 CZ A0 1010 CZ A0 2Z10 NO A2 1210 C1 20 1120 F1 10 0100 R2 BC 1100 10 AA 1410 E1 10 1110 E1 10 1210 E9 10 1110 EC 10 1310 EJ 10 1030 EJ 10 1111 EJ 20 1120 EJ 10 1120 EJ 20 1110 EX 10 0100 EX 10 0200 10 S9 0110 F0 C0 A000 XS X X XS DESCRIPTION Hinged Door Closure Tailgate Style Compartment Options Hinged 100amp Shore Line Connection Location Only 12 120 Volt Inverter Location Only Additional Batteries Location Only Shore Line Hatch in Floor Compartment Lights 1 OSS LightStick lower comp t only STREETSIDE REAR Compartment S3 WI Width 70 0 66 0 S2S 63 0 DO LOW Hinged Door 3 16 Unpainted Interior Panel Vert Hinge Hinged Door Handle D ring w lock Hinged Door Closure Pneumatic Cylinder Compartment Options Hinged Diesel Engine Driven Generator Location Only Compartment Lights 1 OSS LightStick p comp t CURBSIDE FORWARD Compartment C1 WI Width 46 0 LOW Hinged Door 3 16 Unpainted Interior Panel Horiz Hinge Hinged Door Handle D ring w lock Hinged Door Closure Tailgate Style Compartment Options Hinged Cab Tilt Control Location Only Air Conditioning Compressor Location Only Compartment Lights 1 OSS LightStick p comp t Curbside Slideout Compartment CURBSIDE
18. CENTER ROCKER SWITCH PANEL The center main rocker switch panel shall include six 6 LED backlit and labeled rocker switches mounted in the left hand side of the panel The single row of switches shall be located across the top left of the panel The right hand section of the panel shall be left free to accommodate flush mounted equipment BATTERY JUMPER STUDS Battery jumper studs shall be provided in the driver s step area The studs allow the vehicle to be jump started or cab to be raised in an emergency due to battery failure SVI 603 03 27 07 Page 22 of 86 Maui Police Department SVI Trucks Production Specification CO 3 INSTRUMENTATION An ergonomically designed instrument panel shall be provided The gauges shall be backlit with red LED lamps All gauges shall be driven by stepper motor movements The instrumentation system shall be multiplexed and shall receive engine and transmission information over the J1587 data bus to reduce the number of redundant sensors The instrument panel shall contain the following gauges One 1 electronic tachometer with integral digital hour meter The scale on the tachometer shall read from 0 to 3000 RPM The hourmeter shall display engine hours of operation One 1 electronic speedometer with integral digital odometer tripodometer The speedometer shall have a dual scale with miles per hour MPH as the dominant scale and kilometers per hour KPH on the minor scale The speedometer scale shall r
19. INTERMEDIATE Compartment C2 WI Width 46 0 LOW Hinged Door 3 16 Unpainted Interior Panel Horiz Hinge Hinged Door Handle D ring w lock Hinged Door Closure Tailgate Style Compartment Options Hinged Air Conditioning Compressor Location Only Compartment Lights 1 OSS LightStick p comp t CURBSIDE REAR Compartment C3 WI Accessory Mounting 12V outlet Width 70 0 66 0 S2S 63 0 DO LOW Hinged Door 3 16 Unpainted Interior Panel Horiz Hinge Hinged Door Handle D ring w lock Hinged Door Closure Tailgate Style Compartment Options Hinged Stairway Storage Compartment Lights 1 OSS LightStick p comp t REAR CENTER Rear Center Storage Compartment RC1 Patch Panel Compartment RC2 Interior Outlet 12 Volt Accessory Plug MISC BODY OPTIONS Plastic Tile DriDek Compt Floor Shelving and Trays Plastic Tile Color Black Rope Tie Off Roof Mounted Stainless Thresholds All Compartments Awning Curbside Awning 14 Awning Color Natural Roll out Awning Body Side Curbside Awning Color White Exterior Removable Desk Exterior Dri Erase Board WALK IN Interior Finish 21 26 Whiteboard Magnetic Custom Gab Body Walk Thru Opening 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2
20. be a two point top and bottom rotary slam double catch latch recessed inside the double panel door with striker plate All cab and body exterior compartment D ring locks shall be keyed alike The hinged door s shall have a pair of tailgate style mechanisms to stop the door at 90 degrees Each door shall be capable of being closed without unlatching This compartment shall have the following items There shall be one 1 OnScene Solutions 18 LED light stick installed in this compartment Each light shall be mounted horizontally inside the compartment door There shall be 30 LEDs per 18 light The light stick shall be rated at 100 000 hours of service Each light stick shall be provided with a 5 year free replacement warranty SVI 603 03 27 07 Page 43 of 86 Maui Police Department SVI Trucks Production Specification CO 3 STREETSIDE COMPARTMENT INTERMEDIATE S2 The interior useable compartment width shall be approximately 64 0 wide The approximate compartment door opening shall be 57 0 wide This compartment shall have a horizontally hinged box pan style door fabricated of 1 8 thick smooth aluminum The inner liner of the door shall be 3 16 thick smooth aluminum with an unpainted finish The door exterior shall be painted job color The hinged door s shall have a stainless steel 6 Hansen offset bent D ring locking handle A gasket shall be placed between stainless steel handle and door Door latches shall be a two poi
21. be seven 7 120 volt outlet strip s approximately 4 long with straight blade household type outlets provided on the interior of apparatus body 15 ampere circuit breaker protection shall be provided for each strip Two 2 under cab dispatch L desk Two 2 under streetside OPS slide out desk Two 2 under curbside OPS slide out desk One 1 under OPS center table INTERIOR BODY 120 VOLT LIGHTING There shall be twelve 12 120 volt light s installed in the walk in area of the body The fixtures shall be single bulb 22 watt fluorescent lights with fully enclosed protective lens covers and flush aluminum trim Each light shall be recessed down the center of the walkway The operation of the lights shall be at the entry doorway area The interior lights shall be wired to the generator system with a 15 amp circuit breaker protection SVI 603 03 27 07 Page 72 of 86 Maui Police Department SVI Trucks Production Specification CO 3 INTERIOR LIGHT FIXTURE There shall be six 6 120 volt interior over counter fluorescent light fixture s installed above the desk deck area Fixture shall be provided with single bulb and switch on fixture Two 2 at cab dispatch cieling Two 2 at each streetside OPS slide out desk Two 2 at each curbside OPS slide out desk DIESEL GENERATOR An Onan model 8HDKAU diesel driven generator shall be installed on the apparatus The generator shall be rated at 8 000 watts at 120 240 volts Current
22. box pan style door fabricated of 1 8 thick smooth aluminum The inner liner of the door shall be 3 16 thick smooth aluminum with an unpainted finish The door exterior shall be painted job color The hinged door s shall have a stainless steel 6 Hansen offset bent D ring locking handle A gasket shall be placed between stainless steel handle and door Door latches shall be a two point top and bottom rotary slam double catch latch recessed inside the double panel door with striker plate The hinged door s shall have a pair of tailgate style mechanisms to stop the door at 90 degrees Each door shall be capable of being closed without unlatching This compartment shall have the following items The cab tilt control pendant An air conditioning system compressor shall be located in this compartment There shall be one 1 OnScene Solutions LED light stick mounted horizontally inside this compartment Each light stick shall include a 36 section above the subframe and an 18 section below the subframe There shall be 30 LEDs per 18 light and 60 LEDs per 36 light The light stick shall be rated at 100 000 hours of service and shall be provided with a 5 year free replacement warranty CURBSIDE SLIDEOUT COMPARTMENT AN exterior compartment shall be located centered in the curbside slideout A horizontally hinged lift up double pan door shall be provided with lockable D ring handle Compartment shall house the components to make it p
23. cab The rails shall be located at the retracted door window glass level and will protect the exposed window glass area INTERIOR LIGHTING The cab interior lighting shall consist of the following A red white dome lamp shall be located over each door The white lamp shall be activated by its respective door when opened and both activated by an individual switch on the light A red white dome lamp with individual switches shall be located in the headliner over the engine tunnel to serve as a tunnel surface light FLASHING DOOR AJAR LIGHT A red flashing door ajar light shall be located in the headliner centered in the cab The light shall be 6 00 long x 2 50 wide x 1 75 high and labeled Do Not Move Apparatus The light shall be wired to indicate an open door on the cab when the parking brake is released ENGINE TUNNEL LIGHT A Trucklite 4 diameter clear work light shall be provided and installed under the engine tunnel SVI 603 03 27 07 Page 25 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CLEAR DOME LAMP S Two 2 Two 2 7 clear dome lamp s with two 2 switch s shall be mounted in the headliner of the cab DOME LAMP ACTIVATION Two 2 7 dome lamp s shall be activated by any door in addition to two 2 push button switch s MAP LIGHT A Roxter gooseneck style instrument panel map light with switch at base shall be installed on the right hand side of the dash panel WEATHER BAND AM FM
24. cab lowering The safety assembly shall fall over the lift cylinder when the cab is in the up position A cable release system shall also be provided to clear the safety assembly from the lift cylinder when lowering the cab SVI 603 03 27 07 Page 28 of 86 Maui Police Department SVI Trucks Production Specification CO 3 RECEPTACLE FOR CAB TILT CONTROL A receptacle shall be installed in the right hand side of the front bumper tail to provide a place to plug in the cab tilt remote control pendant CUT OUT IN REAR CAB WALL The rear wall of the 20 raised roof cab shall be cut out 24 W x 72 H for walk through application WHEEL WELL LINERS Full width wheel well liners shall be installed on the extruded cab to limit road splash and enable easier cleaning The two piece liners shall consist of an inner liner 16 wide made of vacuum formed ABS composite and a outer fenderette 3 50 wide made of 14 gauge 304 polished stainless steel EXTERIOR CAB ASSIST HANDLES Three 3 18 knurled anti slip one piece exterior assist handles shall be installed one 1 behind each cab door The assist handle shall be made of 14 gauge 304 stainless steel and be 1 25 diameter to enable easy grabbing with the gloved hand EXTERIOR PAINT All cab painting must be completed prior to the installation of glass accessories or any other cab trim to assure complete paint coverage and maximum corrosion protection The entire cab must be disc ground to remove any
25. catch two point safety slam latch recessed inside the double panel door with strike plate mounted top and bottom of door frame ENTRY HANDRAILS There shall be two 2 handrails provided at entry door one 1 vertical on exterior of body on door handle side and one 1 on inside of door The interior handrail shall be angled for optimum use when entering or exiting the walk in portion of the body Handrails shall be NFPA compliant 1 1 4 extruded aluminum tubing with chrome plated end stanchions WINDOW S There shall be one 1 18 wide x 22 vertical sliding window s installed in the entrance door Each window shall have tinted automotive type safety glass mounted in an extruded aluminum frame The frame shall have a black anodized finish SWING DOWN ENTRY STEPS Body side entry shall be provided with swing down entry steps that store under body entry door when not in use INTERIOR SPECIFICATIONS INTERIOR INSULATION Following the sheet metal fabrication the roof area upper exterior walls and the entry door of the apparatus body shall be insulated with 1 1 2 rigid polyurethane foam insulation This insulation shall be the type that will not absorb moisture move once in place or deteriorate Mat type fiberglass or spray in foam insulation are not acceptable INTERIOR FINISH The interior of the apparatus body shall have a fully maintenance free and durable finish The interior finish shall be installed on the ceiling front wall and in
26. coat clear coat finish shall be power sanded and machine finished to achieve a flat finish on all A visual surfaces SVI 603 03 27 07 Page 29 of 86 Maui Police Department SVI Trucks Production Specification CO 3 OPERATORS MANUAL AND PARTS LIST A chassis operator s manual and parts list with wiring and air plumbing diagrams shall be provided The wiring and plumbing diagrams shall be of the chassis model ENGINE AND TRANSMISSION OPERATION MANUAL One 1 engine operation and maintenance manual and one 1 transmission operation manual shall be included in the Spartan operator s manual FIRE EXTINGUISHER A 2 5 pound BC D O T approved fire extinguisher shall be shipped loose with the cab ROAD SAFETY KIT A road safety kit shall be provided and shall consist of three 3 DOT approved reflective triangles SVI 603 03 27 07 Page 30 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CHASSIS MODIFICATIONS LUBRICATION PLATE A permanent plate shall be installed in the Driver s compartment which indicates the type and quantity of the following fluids in the vehicle Engine Oil Engine Coolant Transmission Fluid Drive Axle Fluid Air Conditioning Refrigerant Air Conditioner Oil if applicable Power Steering Fluid Cab Tilt Fluid if applicable Transfer Case Fluid if applicable Pump Transmission Fluid if applicable Pump Primer Fluid if applicable Equipment Rack Air Compressor Generator etc
27. crimp water tight heat shrink connectors Wire nut insulation displacement or insulation piercing connections shall NOT BE ACCEPTABLE All 12 volt wiring running from front to back of apparatus body shall be run in full length electrical wiring raceway down each side of body All 12 volt circuits shall be protected with properly rated low voltage over current devices Such devices shall be readily accessible and protected against overheating mechanical damage and water spray All switches relays terminals and connectors shall have a rating of 125 of maximum current for which the circuit is protected A complete electrical wiring schematic of actual system shall be provided with finished apparatus Similar or generic type electrical schematics shall NOT BE ACCEPTABLE A low voltage final test certification shall be provided with delivered apparatus 12 VOLT MULTIPLEX CONTROL CENTER The apparatus shall have a multiplexed 12 volt electrical system that will provide complete diagnostic capability The system shall have the capability of delivering multiple signals via a CAN bus utilizing specifications set forth by SAE J1939 The system shall be node based to maximize stability so that failure of one node does not affect the operation of the other nodes The system shall use shielded twisted pair wire for transmission of system function signals The shielded wire shall provide protection against EMI and RFI noise interruptions The multiplex s
28. ductable unit with a rotatable variable speed blower insulated condensate drip pan with anti slosh antifungal foam lining with an air filter Interior air temperature will be controlled by a wall mounted SMX Series computerized control The individual cooling units shall be connected to two 2 undercarriage mounted Type ACA 230 volt AC 23 9 amps start full load 14 000 Btu hr each condensing units Size 26 L x 18 D x 15 H Weight 44 lbs Each condensing unit features refrigerant condenser compressor and associated electrical and mechanical components in an aluminum enclosure Refrigerant connections are located on the front of unit Blower type unit pull air in through the coil in back and discharge in back through the bottom or front of unit The system will be completely tested prior to delivery for cooling capabilities and refrigerant line leaks The entire system shall be designed and installed per Dometic Cruisair installation requirements for air flow refrigerant line length and sizing and condenser cooling and air flow STREETSIDE INTERIOR AREA SVI 603 03 27 07 Page 54 of 86 Maui Police Department SVI Trucks Production Specification CO 3 SLIDE OUT EXTENSION There shall be one 1 slide out section s which shall extend approximately 32 as measured from the outside of the body The extendable module shall be approximately 124 5 in length 116 5 interior and the interior height shall be approximately 9 less that
29. engine A shroud and recirculation shield system shall be used to ensure air that has passed through the radiator is not drawn through it again COOLANT FILTER An engine coolant filter with a shut off valve shall be installed on the engine The location of the filter shall allow for easy maintenance TRANSMISSION The transmission shall be an Allison 3000 EVS automatic with electronic controls The transmission shall have two 2 10 bolt PTO pads The transmission shall be equipped with an air to oil transmission cooler located below the radiator allowing a single depth core and efficient cooling package The transmission cooler shall be mounted in a manner to allow maximum approach angle by not protruding below the frame more than an inch The transmission cooler shall be constructed completely of aluminum with welded side tanks The transmission shall have two 2 internal oil filters Fourth gear hold in range may be accomplished by wiring for a pumping application The transmission gear ratios shall be 1st 3 49 1 2nd 1 86 1 3rd 1 41 1 4th 1 00 1 5th 0 75 1 6th 0 64 1 if applicable Rev 5 03 1 Transmission to be provided with I O pack 119 for rescue interlock TRANSMISSION COOLING SYSTEM Transmission Cooler The transmission cooler shall be a cross flow air to oil design constructed completely of aluminum with welded side tanks The transmission cooler shall have a minimum of a 136 square inch core and shall be bolted to the bo
30. rear axle to rear of body shall be single one piece sections Compartment floors shall be preformed then positioned in body and welded into final position Compartment floors shall have a sweep out design with door opening threshold positioned lower than compartment floor permitting easy cleaning of compartments Angles lips or door moldings are not acceptable in the base of compartment door opening One way rubber drain valves shall be provided in compartment floors so that a water hose may be used to flush out compartment area All seams in sheet metal below frame and around the rear wheel well area shall be welded continuous to prevent moisture from entering compartments All other interior seams and corners shall be sealed with silicone based caulk prior to painting Only stainless steel bolts nuts and sheet metal screws shall be used in mounting exterior trim hardware and equipment Exterior compartments shall be machine louvered in lower back wall of compartment for ventilation ROOF CONSTRUCTION The roof shall be integral with the body and shall be all welded construction The roof of the body shall be not less than 3 16 aluminum 3003H 14 alloy smooth plate fully and continuously welded in place The roof shall be reinforced with 2 x 2 x 1 4 aluminum tubing running the full width of the body A 2 rounded radius shall be provided along the body sides BODY SUBFRAME To assure proper body alignment and clearance the body subfram
31. regulation 29 test the frontal area of the cab is struck by a 3 700 pound pendulum weight The weight is brought back to a sixty degree angle and then the weight is released and allowed to swing forward imparting some 32 600 Ib ft of force to the cab front face The cab must be so constructed that after the test there will be minimal intrusion of cab structure into the passenger area Note After the test the Spartan cab doors remained usable for both entry or exit Also as part of the test the cab roof must withstand a static load bearing test The Spartan cab withstood a weight of over 60 000 pounds without permanent damage or collapse The above tests were witnessed by and attested to by an independent third party The test results were recorded on by cameras high speed imagers accelerometers and strain gauges Notarized copies of the letters verifying the test results and videos of said test are available upon request ONE YEAR CHASSIS WARRANTY The chassis manufacturer shall warrant to the original purchaser the custom fire truck chassis for a period of twelve 12 months with the exception of the actual fire apparatus chassis frame which carries a lifetime warranty The warranty period shall begin on the date the vehicle is delivered to the original purchaser The warranty may include conditional items which shall be listed in the detailed warranty document that shall be provided upon request CAB WARRANTY The cab shall be warranted for a pe
32. shall have a 1 25 lip around the top of bucket to secure and seal the bucket to the roof The bucket shall have an aluminum drain tube welded into the bottom of the bucket to allow water hose to be attached to drain water to the ground ELEVATED ANTENNAS Three 3 radio antennas one 1 for Daniels 800 MHz one 1 for Daniels UHF and one 1 for Daniels VHF radios shall be mounted on a custom bracket mounted on elevated camera mast The antenna shall be mounted in such a way as to not interfere with the operation of camera system in any way Antenna cables shall be run through the Nycoil conduit with camera cable MAST COVER AND MOUNTING The above telescoping mast shall have a custom designed 1 8 smooth aluminum cover painted body color provided to store control cables air hose and to protect the mast from the elements The cover shall be easily removed to allow access to mast for maintenance The camera nesting location shall be such that mast shall be mounted as low as possible a interlock shall be provided to eliminate power to camera unless tower is raised SVI 603 03 27 07 Page 79 of 86 Maui Police Department SVI Trucks Production Specification CO 3 TELESCOPING LIGHT MAST The apparatus shall be equipped with one 1 pneumatic powered telescoping floodlighting tower s The mast shall utilize air from the chassis brake system Air to operate the telescoping mast must be drawn from a drier system and be regulated to 20 psig and
33. surround the wheel well area The interior wheel well area shall be designed so that it does not accumulate dirt or water SVI 603 03 27 07 Page 38 of 86 Maui Police Department SVI Trucks Production Specification CO 3 ALUMINUM BODY PAINT SPECIFICATIONS The final finishing of this apparatus shall be to fire apparatus standards exhibiting excellent gloss durability and color retention properties Commercial type paint finish shall not be acceptable A warranty sheet with all conditions shall be provided with completed apparatus All flush mounted lights drip moldings windows and other equipment shall be fitted to the apparatus prior to paint finishing then removed to assure full paint coverage under all equipment The apparatus body shall be sanded smooth on all exterior surfaces to assure removal of all imperfections in metal surface and to assure good adhesion of paint to body All metal surfaces shall be chemically cleaned and metal etched with acid cleaner prior to paint The body shall receive a corrosion resistant epoxy primer coat The primer coat shall be lightly sanded to assure a smooth surface for a final coat All seams and corners in sheet metal on interior and exterior shall be sealed with automotive type caulk prior to painting finish coat Prior to the assembly and reinstallation of lights handrails door hardware and any miscellaneous items an isolation tape or gasket material must be used to prevent damage to the f
34. the subframe There shall be 30 LEDs per 18 light and 60 LEDs per 36 light The light stick shall be rated at 100 000 hours of service and shall be provided with a 5 year free replacement warranty SVI 603 03 27 07 Page 48 of 86 Maui Police Department SVI Trucks Production Specification CO 3 COMPARTMENT RC1 STORAGE COMPARTMENT An exterior compartment shall be located on the rear face of the body below specified patch panel compartment RC2 A horizontally hinged drop down double pan door shall be provided with lockable D ring handle COMPARTMENT RC2 TECHNICAL PANEL An exterior compartment shall be located on the rear face of the body above specified storage compartment RC1 A horizontally hinged lift up double pan door shall be provided with lockable D ring handle Technical component connections shall be mounted in console so that connections are angled towards ground There shall be one 1 electrical outlet located in patch panel compartment 120volt 20amp straight blade There shall be two 2 12 volt accessory plug s furnished and installed in the patch panel compartment SVI 603 03 27 07 Page 49 of 86 Maui Police Department SVI Trucks Production Specification CO 3 PLASTIC FLOOR AND SHELF TILE All compartment floors shelves and trays shall be covered with Dri Deck plastic interlocking grating The plastic floor tile shall be black Four 4 small tie off point s shall be furnished and installed on the bo
35. work INTERNET IN PROCESS SITE The Bidder shall post and maintain a website where the Maui Police Department will be able to view digital images of their apparatus as its being manufactured The digital images shall be posted once a week starting when the body begins production or when the cab chassis arrives and shall continue until the final completion of the apparatus NFPA REQUIRED MANUALS The construction operation and service documentation shall be provided on a CD ROM These manuals shall be written in a step by step format for ease of reference There shall be two 2 copies of the CD provided with the apparatus as standard CONSTRUCTION PERIOD The Bidder shall specify the number of days after award of the contract and after receipt of cab chassis in which the apparatus will be completed The maximum period for construction shall be three hundred sixty five 365 days after receipt of Purchase Order Bidder shall not be held liable for delays of chassis delivery due to accidents strikes floods or other events not subject to their control Bidder shall provide immediate written notice to Maui Police Department as to delays and to what extent these delays have in completing apparatus within the stated construction time period SVI 603 03 27 07 Page 3 of 86 Maui Police Department SVI Trucks Production Specification CO 3 WARRANTY The Bidder shall provide a full statement of the warranty provided for the vehicle s being b
36. 01 Standards The stripe shall conform to ASTM 4965 Standard Specifications for Retroreflective Sheeting for Traffic Control Type Ill Class 1 or Class 3 The length of stripe shall be 50 of the cab and body length of each side 50 of the rear of the body and 25 of the front width of apparatus This reflective stripe shall be white The stripe shall remain in a straight line from the front of the vehicle to the rear REFLECTIVE STRIPE CAB A 6 reflective stripe shall be provided on specified cab in compliance with NFPA 1901 standards The stripe color shall be white LETTERING The following lettering shall be furnished and installed on the completed unit LETTERING GRAPHICS 5 000 00 is included in total bid amount to provided a lettering graphics package acceptable to Maui Police Department SVI will notify Maui Police Department after design of their lettering graphics if this amount is more or less than total budget amount COMPARTMENT INTERIOR FINISH The interior of compartments shall be painted with an epoxy primer then painted with a textured Zolotone paint finish Paint color shall be grey SVI 603 03 27 07 Page 40 of 86 Maui Police Department SVI Trucks Production Specification CO 3 EXTERIOR COMPARTMENT DOORS HINGED DOOR CONSTRUCTION The exterior compartment doors shall be custom manufactured and built for each compartment These doors must be able to withstand years of rugged service and wear For this reason
37. 1 rated as being capable of producing a minimum of 15 8 cfm It shall be gear driven engine oil pressure lubricated and cooled by the engine cooling system ENGINE WARRANTY The Caterpillar engine shall be warranted for a period of five 5 years or 200 000 miles whichever occurs first FUEL WATER SEPARATOR WITH LIGHT AND ALARM A Caterpillar combination primary filter fuel water separator shall be installed with an instrument panel lamp and audible alarm to indicate when water is present in the fuel The secondary filter shall also be provided and mounted on the engine in a convenient serviceable location PAC BRAKE ENGINE EXHAUST BRAKE An engine exhaust brake shall be installed in the engine exhaust system to serve as a speed retardation device There shall be an on off switch located on the instrument panel The driver releasing the accelerator will activate the brake when the switch is in the On position The exhaust brake shall activate an aggressive downshifting of the transmission to enhance the exhaust brake s performance SVI 603 03 27 07 Page 17 of 86 Maui Police Department SVI Trucks Production Specification CO 3 EXHAUST SYSTEM The exhaust system shall be installed under the frame with the discharge to the left side forward of the rear tires A muffler and 065 wall aluminized steel exhaust tubing supported by bolted on frame brackets shall be installed Stainless steel flex tubing is to be installed between exhaust pipe a
38. 2H sliding Rear Interior Cabinet Counter Height 16 26 w 30 45 h Interior Cabinet Hinged Door counter cab Interior Cabinet Two Shelves Interior Cabinet Overhead 24 48 w 11 16 h Interior Cabinet Sliding Steel Doors Interior Desk Smooth Aluminum Slide Out Pencil Drawers Interior Seat Herman Miller Individual Pedestal INTERIOR AREA IS3 WI ORW Interior Options ORW WI Mid Atlantic WR ROR 37 space 19 Data Rack INTERIOR AREA IS4 WI BRW Interior Options BRW WI Interior Bench Seat Above Exterior Compartment CURBSIDE INTERIOR AREA Slide Out Command Wall 84 There shall be a removable desk storage area in the lower portion of the exterior wall of the slideout Window 18Wx22H sliding Front Window 18Wx22H sliding Rear Interior Cabinet Overhead 24 48 w 11 16 h Interior Cabinet Sliding Lexan Doors Interior Desk Smooth Aluminum Slide Out Pencil Drawers Interior Seat Herman Miller Individual Pedestal AM FM Radio INTERIOR AREA IC3 WI ORW Interior Options ORW WI Mid Atlantic WR ROR 37 space 19 Data Rack Data Rack shall be provided by customer Ordered through Harmer Communication INTERIOR AREA IC4 WI BRW Interior Options BRW WI TV Smart Board Location Only Interior Conference Tables Interior Bench Seat Above Exterior Compartment Removable Desk AM FM R
39. 3 MARKER LIGHTS The apparatus body shall be equipped with all necessary clearance lights and reflectors in accordance with Federal Motor Vehicle Safety Standards FMVSS regulations All body clearance lights shall be LED to reduce the need for maintenance and lower the amp draw Clearance lights shall be wired to the headlight circuit of the chassis STEP LIGHTS GROUND LIGHTS There shall be three 3 clear lens door step area scene light s provided on the apparatus Lights shall be placed at each apparatus entry door and step where personnel climb on or descend from apparatus to ground level All of the ground lights shall be activated when the parking brake is set LICENSE PLATE LIGHT One 1 Arrow 437 chrome plated license plate light shall be installed on the rear of the apparatus body License plate light shall be wired to the headlight circuit of chassis Nutsert inserts shall be provided for license plate installation ELECTRONIC SIREN The siren control head shall be supplied and installed by the cab chassis manufacturer SIREN SPEAKER The siren speaker s shall be supplied and installed by the cab chassis manufacturer SIDE SCENE LIGHTS Two 2 Whelen 900 series 9 x 7 Opti Scene lights with gradient lens and chrome flange shall be provided one 1 each side in rearward corners of upper body Two 2 switches shall be provided one 1 for the streetside scene lights and one 1 for the curbside scene lights REAR SCENE LI
40. 7 Page 86 of 86
41. All Belts to Seat type integrated red three point shoulder harness with lap belt and an automatic retractor built into the seat assembly The female seat belt clasp shall extend up from the seat base 14 to be within easy reach of the occupant The ABTS feature is an engineering break through where the passenger restraint harness is built into the seat module and meets the twenty G load test OFFICER SEAT The officer s seat shall be an eight way electric H O Bostrom Sierra high back seat and shall include a tapered and padded seat cushion and back with mechanical suspension The seat shall be an ABTS All Belts to Seat type integrated red three point shoulder harness with lap belt and an automatic retractor built into the seat assembly The female seat belt clasp shall extend up from the seat base 14 to be within easy reach of the occupant The ABTS feature is an engineering break through where the passenger restraint harness is built into the seat module and meets the twenty G load test ELFD COMPARTMENT The cab shall contain an exterior compartment on each side of the cab behind the rear doors The compartment opening shall be 16 25 wide x 21 19 high The compartment size shall be 17 84 wide x 21 19 high x 21 19 deep The compartment shall have a 17 13 wide 32 00 high and 1 50 thick hinged box pan style flush mount door with a locking bent D ring slam latch with door switch to activate open compartment warning light in cab S
42. Amps 1500W Engine Heater 12 5 Amps 120V Air Compressor 4 2 Amps SVI 603 03 27 07 Page 24 of 86 Maui Police Department SVI Trucks Production Specification CO 3 MARKER LAMPS Five 5 I C C DOT approved Weldon model 9186 1500 20 Light Emitting Diode LED cab marker lamps shall be installed on the face of the cab above the windshield INTERSECTOR LIGHTS Two 2 Whelen 4x6 Super LED blue wide angle warning lights shall be installed on each cab radius or the bumper tail to act as intersector lights Blue LEDS SCENE LIGHTS Two 2 Whelen 900 series clear halogen scene lights shall be installed on the sides of the cab The lights shall be surface mounted one 1 each side of the cab The lights shall be controlled by separate switches one 1 for the left side and one 1 for the right side THREE DOOR CAB COMMAND CENTER The left rear crew cab door shall be eliminated and the cab trimmed so it can be converted into a command cab by the apparatus builder DOOR WARNING CHEVRON Three 3 Chevron reflective signs shall be installed on the lowest portion of the inner door panels one 1 on each door A stripe of reflective tape shall be installed at the outer edge of each door FULL WIDTH CREW CAB DOOR ASSIST RAILS Black powder coated cast aluminum assist rails shall be provided and installed on the inside of the rear crew doors the full width of the window glass The rails shall assist personnel in exiting and entering the
43. ELC installed The use of supplemental coolant additives SCA will not be allowed as this is part of the extended life coolant makeup The use of ELC provides longer life and change intervals providing improved performance The coolant shall contain ethylene glycol and deionized water to keep the coolant from freezing to a temperature of 34 degrees F Hoses Clamps Radiator All radiator tubes shall be formed from aluminized steel tubing and installed with silicone hoses with stainless steel constant torque clamps Recirculation Shields Recirculation shields shall be installed where required to prevent heated air from reentering the cooling package and affecting the performance Charge Air Cooler The charge air cooler shall be a cross flow design constructed completely of aluminum with welded side tanks The charge air cooler shall have a minimum of a 401 sq in core and be bolted to the top of the radiator to allow a single depth core thus allowing a more efficient and serviceable cooling system SVI 603 03 27 07 Page 18 of 86 Maui Police Department SVI Trucks Production Specification CO 3 Hoses Clamps Charge Air Cooler All charge air cooler tubes shall be formed from aluminized steel tubing and installed with silicone hump hoses and stainless steel T style clamps meeting the engine manufactures requirements COOLING SYSTEM FAN The engine cooling system shall incorporate a heavy duty composite fan belt driven on the
44. GHTS Two 2 Whelen 900 series 9 x 7 Opti Scene lights with gradient lens and chrome flange shall be provided on upper rear body One 1 switch shall be provided for rear scene lights The rear scene lights shall also be activated when the apparatus is in reverse SIDE SCENE LIGHTS Four 4 Whelen 508 series 8 x 5 Opti Scene lights with 8 32 degree lens and chrome flange shall be provided two 2 each side of upper body Lights shall be located two 2 on the streetside slideout and two 2 on the curbside slideout Two 2 switches shall be provided one 1 for the streetside scene lights and one 1 for the curbside scene lights SVI 603 03 27 07 Page 65 of 86 Maui Police Department SVI Trucks Production Specification CO 3 WARNING LIGHT PACKAGE The following lighting package includes all of the minimum warning light requirements to comply with the most recent NFPA 1901 Fire Apparatus Standard UPPER WARNING LIGHT SYSTEM ZONE A FRONT WARNING LIGHT There shall be one 1 Whelen Edge FN72QLED LED 72 lightbar permanently mounted to the cab roof The lightbar configuration streetside to curbside shall be SECTION Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 7 Section 8 Section 9 Section 10 Section 11 Section 12 INTERNAL COMPONENTS One 1 Blue Linear LED Side Facing Clear One 1 Blue Corner LED Blue Linear LED Clear Linear LED Clear Halogen
45. If metal they shall be made of non corrosive material Nameplates shall show make model serial numbers and other such data necessary to positively identify the items All plates shall be mounted in a conspicuous place with stainless steel screws and bolts MATERIALS The materials specifications are considered absolute minimum Exceptions will not be accepted or permitted since all raw materials of specified type are available to all manufacturers Since all manufacturers have the ability to shear break and weld as these specifications require all basic design requirements shall be complied with Materials shall conform to the specifications listed herein When not specifically listed materials shall be of the best quality for purpose of commercial practice Materials shall be free of all defects and imperfections that might affect the serviceability of finished product SVI 603 03 27 07 Page 2 of 86 Maui Police Department SVI Trucks Production Specification CO 3 QUALITY AND WORKMANSHIP The manufacturing process including quality control shall be consistent with present industry standards All equipment material and articles required under these specifications are to be new or fabricated from new materials produced from recovered materials The term Recovered Materials means materials which have been collected or recovered from solid waste and reprocessed to become a source of raw materials as opposed to virgin raw materials No
46. LAD Fuel Shut off Valve at Fuel Tank DIA GLAD MET Tail Pipe Chrome Exhaust Ext 45Deg Air Cleaner amp Air Restriction Indicator Stop Tail Turn Wiring to Rear of Chassis Trans Range Selector Push Pad Std Drivelines 1710 Heavy Duty Series ADV BE DIA GLAD MET MS gt Multiplex Electrical Sys 6 Batteries DIA GLAD Rocker Switch Console Three Panel ABS Mux Officer Rocker Switch Panel Mux Vista Display Driver Rocker Switch Panel Mux Vista Display Center Rocker Switch Panel Six 6 Switches LH Battery Jumper Studs DIA GLAD gt Instrumentation Standard lt gt Siren Whelen WS 295HFS2 Flush in Center Panel m Ce ee Ca Cn CR Cian Cn CEI CREE COREE CEES CURE a a a cp gt EE a a M CRITI CURTIN CITIES CEI CRITI CURT CEES COREE CERES CORTON CEOS CHE CREE CURTIN CEI CEE CREE CORTON CREE GEE 03 27 2007 PART NO DESCRIPTION Location left side of center panel 15 15 1400 15 40 5700 16 05 2300 16 31 7100 gt Power amp Ground Studs Battery Direct Std ADV DIA GLAD MET MS gt Super Auto Eject 20Amp Kussmaul gt Marker Lamps Cab LED Weldon CabFace Abv Windshield gt Whelen LED 4x6 Dual Blue Lights on Cab Radius Blue LEDS 16 36 1700 17 ZZ 9600 18 08 0300 19 15 2500 gt Whelen 900 Ser Gradient Lens Clr Scene Lts on Cab Side gt Three Door Cab for Command Center DIA GLAD gt Door Warning Chevron gt Assist Handles Full Width Crew Door Cast Alum 19 40 0500 19 40 0700 19 40 1500 19 40 2300 19 40 3900 19
47. ODEL 6 25 SPECIFICATIONS Nested height tower only 5 10 Extended height tower only 25 0 Normal payload capacity 150 Ibs Number of sections 6 Tube diameter range 6 3 4 3 Mast volume 2 7 cu ft Collar type Non locking Maximum operating pressure 35 psi MICROWAVE ANTENNA Microwave antenna shall be installed on telescopic mast Customer to supply antenna mounted requirements prior to construction SVI 603 03 27 07 Page 80 of 86 Maui Police Department SVI Trucks Production Specification CO 3 ELECTRONIC PATCH PANEL An electronic patch panel shall be provided on curbside of rear wheel well area for audio video etc input outputs as follows 1 Eight 8 composite video inputs RF 2 Eight 8 composite video outputs RF 3 Four 4 pair RCA audio inputs 4 Four 4 pair RCA audio outputs 5 Four 4 RCA video inputs 6 Four 4 RCA video outputs 7 Four 4 BNC video inputs 8 Four 4 BNC video outputs 9 Four 4 CAT 5 inputs 10 Four 4 CAT 5 outputs 11 One 1 distribution module located in data rack 12 Four 4 RJ 11 phone jacks All wiring shall terminate inside the rear 19 data rack cabinet VIDEO MONITORS Two 2 20 multi function flat panel monitors with built in TV tuner shall be provided two 2 located in forward operations section centered over streetside slide out desk Monitors shall be installed on wall mount brackets System shall be complete and fully operational includ
48. Production Specifications CO 3 Maui Police Department Sydney Kikuchi 55 Mahalani Street Wailuku HI 96793 808 244 6410 Maui Police Department Sydney Kikuchi 55 Mahalani Street Wailuku HI 96793 808 244 6410 Quote No MPDHICM 0007 Job Order No SVI 603 03 27 2007 PART NO 01 02 2000 01 04 0110 01 08 0100 01 08 A100 01 15 1100 01 15 1300 01 18 0100 01 40 0100 01 40 1100 01 40 2100 01 45 0100 01 45 2000 01 45 3000 01 A0 1000 02 20 0200 00 AA 0000 00 DA 4400 17 EL 2400 18 05 8000 18 09 0500 18 06 4P00 20 25 1300 20 25 3200 20 25 3900 20 30 0800 20 35 1000 23 16 0500 17 FF 0200 16 32 2800 16 37 0500 23 10 3100 25 20 3900 00 XX 0600 00 XX 1000 00 XX 2000 01 10 4000 01 15 0900 01 10 1500 01 30 1000 02 10 1000 03 10 0600 03 30 2700 11 40 2100 DESCRIPTION Boiler Plate Information 2005 400 06 24 05 Insurance 2 000 000 00 Engineering Drawings 17 x 11 Sheet General Construction and Design Internet In Process Site Manuals CD Format 2 Standard No Printed Copy of Manuals Construction Period Warranty Boiler Plate Warranty General 1 Year standard Warranty Structural 10 Years standard Testing NFPA 12 Volt DC Test NFPA 120 240 Volt AC Test Inspection Trip Per Person Per Trip Dealer Options 2005 400 06 24 05 Delivery and Demonstration By Dealer Representative Inc from CO CA port Ocean freight by HT amp T Diamond
49. RADIO WITH COMPACT DISC PLAYER A heavy duty Panasonic Weather Band AM FM stereo radio with compact disc player and four 4 speakers shall be installed in the cab The radio shall be installed above the driver Two 2 speakers shall be installed overhead front with the other two 2 speakers in the upper rear corners of the cab CAMERA DUAL REARVIEW WITH DISPLAY ON VISTA SCREEN An ASA audiovox rearview camera shall be supplied for viewing through the color Vista display panel One camera will be mounted in a location as to afford the driver a clear view of the blind spot on the officer side of the vehicle A second camera will be shipped to the OEM for installation in the body to afford the driver a clear view of the rear of the vehicle A one way communication speaker is to be installed at the rear of the vehicle to allow the backup advisor to use voice commands to direct the driver DASH AND HEADER TRIM ABS The cab interior dash trim shall consist of a two 2 piece vacuum formed ABS composite driver officer panel and center assembly The center dash shall incorporate the integral rocker switch console and incorporate a latching electrical component access cover to allow complete access to the underside of the switch panel assembly and electrical harness and components The A pillar and center windshield post trim shall consist of a vacuum formed ABS composite driver officer and center cover The header trim shall consist of a vacuum for
50. The above cabinet s shall have sliding steeldoors painted white SVI 603 03 27 07 Page 55 of 86 Maui Police Department SVI Trucks Production Specification CO 3 INTERIOR DESK The interior of apparatus shall be provided with a desk top full width of slide out which shall be 24 deep and located approximately 30 from floor The front edge of the desk top shall be reinforced with 2 x 2 tubing in order to support a person sitting on the edge of the desk The desk top surface shall be fabricated of 3 16 smooth aluminum It shall have a 2 vertical back splash along the back edge and a 2 vertical downward edge along front to cover the 2 x 2 reinforcement There shall be 2 1 2 diameter holes with plastic edge grommet provided at each rear corner for wiring of future equipment located on the desk top SLIDE OUT PENCIL DRAWERS There will be one 1 slide out pencil drawers provided under the desk top INTERIOR SEATS Two 2 Herman Miller highly adjustable Aeron Chairs furnished and installed in the body command area slide out Each chair shall have a Kinemat tilt mechanism that allows the body to pivot naturally and simultaneously at the ankles knees and hips providing a smooth ride and proper support from forward leaning to reclining postures There shall be lumbar adjustment vertically through 4 1 2 inch height range Its depth can be set at 3 4 inch or 1 1 4 inches There shall be a suspension system fabricated from unique Pellicle
51. VI 603 03 27 07 Page 9 of 86 Maui Police Department SVI Trucks Production Specification CO 3 EVOLUTION FRONT FASCIA The front cab fascia shall be constructed of impact resistant FRP fiberglass reinforced plastic which will attach to the front cab skin and act as a fascia only The front fascia will cover the front aluminum cab structure from the bottom of the windshield down to the bottom of the cab The front cab fascia shall have provisions for two single Hi Low Beam headlamp modules with integrated side turn marker lamps and up to four warning lamps The front fascia shall allow access to check and fill the engine oil and wiper washer fluid Access is also provided for servicing the windshield wiper motor and linkage ember separator headlamps electrical bulkhead connectors transmission ECU and the multiplex V Mux control The front fascia grille shall be comprised of a stainless steel grille and two additional plastic chromium nickel plated side grilles WARNING LIGHTS Two 2 Whelen 4x6 SUPER LED blue warning lights shall be installed on the cab fascia below the headlamps light to be super LED blue HEADLIGHTS A hinged headlamp and combination turn signal side marker lamp module shall be part of the cab front fascia Two 2 rectangular halogen combination high low beam headlamps shall be provided with an integrated side marker turn signal lamp The headlamps shall be equipped with a Daytime Running light feature whi
52. a on rear curbside printer cabinet PUBLIC ADDRESS SYSTEM A public address system shall be provided that operates through specified phome PBX intercom system and has exterior body speaker s Any required amplifier or switches shall be located in specified data rack with phone system SVI 603 03 27 07 Page 85 of 86 Maui Police Department SVI Trucks Production Specification CO 3 EQUIPMENT The following equipment shall be furnished with the completed apparatus ASSORTED FASTENERS One 1 container of assorted stainless steel nuts bolts screws and washers used in the construction of the apparatus shall be provided with the completed apparatus WHEEL CHOCKS There shall be two 2 NFPA approved folding aluminum wheel chocks provided for 44 diameter tires The wheel chock s shall be mounted on the apparatus location as per the Maui Police Department FLASHLIGHTS Two 2 Streamlight SL 20XP rechargeable flashlight s and charger s shall be provided Each flashlight shall be orange in color Each flashlight shall have a DC charger and storage sleeve The flashlight s shall be mounted on the apparatus location as per the Maui Police Department PORTABLE ELECTRIC CABLE REEL Two 2 Hannay model CR16 10 11 portable cable reel s with 100 of 12 3 SO black electrical cable shall be provided with the completed unit Location of the reel shall be determined by the Maui Police Department at the pre construction meeting SVI 603 03 27 0
53. adio 12 VOLT SYSTEM Standard 12 volt Electrical Custom Cab Walk in 12V Control Center Multiplex Walkin CstmCab Multiplex Display Supplied with Chassis 12V Panel Location Curbside Front Lower Battery System Custom Battery Switch Cab Chassis Supplied Battery Solenoid 200 amp sae Ss Ss Sess a POH AH WW HSH SBP SB SB SB ae Sees esses sa pO HH aS a2 2 3 PND A ae Sa ap SH HSH HSH HSH OO KH LN A St 03 27 2007 PART NO NO 19 2110 NO 19 A130 NO 19 A230 NO 19 A310 NO 20 2200 NO 21 7A00 NO 24 1200 NO 25 1200 NO AA A000 NO AA A100 N1 10 15B0 N1 12 1110 N1 12 2100 N1 12 3100 N1 12 4200 N2 20 0700 N2 A0 0500 N4 20 3100 N4 20 A100 N4 23 1100 N4 20 1400 N9 30 1010 N5 05 1600 N5 09 1100 N5 20 1000 N5 20 2000 N5 20 2520 N5 20 3000 N5 20 3070 N5 20 3B70 N5 20 4000 N5 20 4070 N5 50 7000 N5 50 701 1 N6 20 1000 N6 20 2000 N6 20 2A00 N6 20 3000 N6 20 3040 N6 20 3A00 N6 20 3B40 N6 20 4000 N6 20 4040 RO 05 1600 RO 10 1620 R1 10 1120 R1 15 1110 R1 15 1210 R1 15 1310 R1 15 1410 R1 15 1610 R1 15 1710 R1 30 1220 R2 20 2110 R2 40 1100 NO 19 A130 NO 19 A210 NO 19 A330 R2 40 1200 R2 A0 1100 S DESCRIPTION Battery Charger Xantrex XC Series 50 amp Shore Power Plug Kussmaul 30 Amp Super Auto Eject Electric Auto eject Cover White Shorepower Plug Location Above Generator Door Engine Compartment Light s Cab Chassis Supplied Go
54. age 61 of 86 Maui Police Department SVI Trucks Production Specification CO 3 12 VOLT ELECTRICAL SYSTEM The apparatus shall be equipped with a heavy duty 12 volt wiring system installed with proper devices for the fire service The system shall include all components necessary for complete operation The low voltage electrical system shall meet or exceed current NFPA 1901 Standards and SAE J1292 requirements System wiring shall be stranded copper conductors of a gauge rated to carry 125 of the maximum current for which the circuit is protected All wiring shall be XLPE cross linked type conductors with function identification at least every 3 by color coding and permanent marking with circuit identification Identification shall correspond with schematics provided with the vehicle Wiring shall be mounted in high temperature protective loom secured to body with bolted on clips with nylon wire ties The XLPE wiring shall have an operating temperature range of minus 84 degrees Fahrenheit to plus 302 degrees Fahrenheit Cross linking changes thermoplastic polyethylene to a thermosetting material which has greater resistance to environmental stress cracking cut through ozone solvents and soldering than either low or high density polyethylene Where wire passes through sheet metal grommets shall be used to protect wire and wire looms Wiring shall be protected against heat liquid contamination and damage Electrical connections shall be with double
55. all be installed and isolated to prevent depletion of the air to the air brake system and to act as a supply tank for operating air equipment It shall be plumbed with a 90 psi pressure protection valve on the reservoir supply side BUMPER APRON A 3 16 bright embossed aluminum tread plate apron shall be installed between the bumper and the front face of the cab Stainless steel bolts shall be used to attach the apron to the bumper flange CHROME PLATED TOW EYES Two 2 chrome plated tow eyes shall be installed through the bumper The eyes shall be fabricated from 3 4 thick 1020 ASMT A36 hot rolled steel The inside diameter of the eye shall be 2 00 and have a chamfered edge AIR HORN ACTUATION Air horn actuation shall be accomplished by the steering wheel horn button and a right side officer s mounted Linemaster SP491 S81 foot switch SPEAKERS CPI Two 2 Cast Products Inc bright aluminum 100 watt speakers shall be recessed in the front bumper one each outboard on the driver s and officer s side The speakers shall be bolted to bumper by means of a polished aluminum trim ring on the front face of the bumper SVI 603 03 27 07 Page 12 of 86 Maui Police Department SVI Trucks Production Specification CO 3 FRONT AXLE The front axle shall be an ArvinMeritor MFS 18 with a 3 74 drop and a 71 00 KPI It shall have a capacity of 18 000 pounds GAWR The springs shall be taper type four 4 leaf 54 long and 4 wide with a mil
56. alled and located per Maui Police Department Labor included in 10 AA 1310 RADIO COMMINICATIONS EQUIPMENT TO BE PROVIDED IN BODY Six 6 800 Mhz radios to be installed Two 2 in streetside operations slide out Two 2 in curbside operations slide out One 1 in conference area One 1 in exterior patch compartment Two 2 VHF radios to be installed One 1 in streetside operations slide out One 1 in curbside operations slide out Two 2 UHF radios to be installed One 1 in streetside operations slide out One 1 in curbside operations slide out Two 2 Air Ground radios to be installed One 1 in streetside operations slide out One 1 in curbside operations slide out Equipment to be provided by customer Harmer Communications Labor included in 10 AA 1310 SVI 603 03 27 07 Page 83 of 86 Maui Police Department SVI Trucks Production Specification CO 3 PANASONIC TELEPHONE SYSTEM A telephone and intercom system shall be provided and installed with provisions to connect to connected land lines microwave system provided landlines and Telular connections as available The telephone system shall be accessible from twelve 12 stations located two 2 at desk in back of cab eight 8 in the front Command Area and two 2 in the rear Conference Area The telephone system shall include the following hardware Five 5 land line jack extension inputs for the telephone system shall be located i
57. ame to Bottom of Body 22 5 E Vertical Door Opening Short Compartment with hinged door 17 5 GENERAL Description Dimension G Bottom of Drip Rail to Top of Body 38 5 H Walk in Interior Height 78 0 min dimensions are generic and subject to change during the actual design process BODY WIDTH DIMENSIONS The body shall be 100 0 wide not including drip rail or non permanent fixtures Interior compartment depth dimensions shall be Area Description Dimension Transverse Area 95 5 Above Top of Subframe Compartment Depth 24 5 Below Top of Subframe Ahead of Rear Axle Compartment Depth 23 5 Below Top of Subframe Eng Note Behind the Rear Axle dimensions are generic and subject to change during the actual design process SVI 603 03 27 07 Page 42 of 86 Maui Police Department SVI Trucks Production Specification CO 3 STREETSIDE COMPARTMENT FRONT S1 The interior useable compartment width shall be approximately 64 0 wide The approximate compartment door opening shall be 57 0 wide This compartment shall have a horizontally hinged box pan style door fabricated of 1 8 thick smooth aluminum The inner liner of the door shall be 3 16 thick smooth aluminum with an unpainted finish The door exterior shall be painted job color The hinged door s shall have a stainless steel 6 Hansen offset bent D ring locking handle A gasket shall be placed between stainless steel handle and door Door latches shall
58. amp Single Rear Michelin XZE 11R 22 5 8 25R 24020 ADV BE DIA GLAD MET Wheels Rr Sgl Axle Alcoa Polished Alum 8 25 x22 5 Wheel Bearings Rear Oil Lubricated Air Suspension Aero Glide 24000 Max Air Brake System Single Axle 4136 Cubic Inch gt Brake Dust Shields Single Rear S Cam Only gt Alcoa Durabright Coating ADV DIA GLAD MET MS Axle Cover Kit Stainless Steel All Wheels Service Brake Lock up System Front Wheel Air Dryer Wabco System Saver 1200 Manual Drains on Air Brake System gt Cable Drains Ea Air Line Tubing Nylon Air Tanks Mounted 1 Inboard gt Engine Caterpillar C9 400HP DIA MET MS gt Engine Air Compressor 15 8CFM Bendix Engine CAT 5Yr 200 000 Miles Warranty Fuel Water Sep w Lt amp Alarm CAT Engine Exhaust Brake Pac Brake Exhaust System Under Frame LH Side Cooling System ISL C9 ADV DIA MET MS Engine Fan Standard Coolant Filter w Shutoff Valve ISC ISL ISM C7 C9 C11 C13 gt Trans Allison 3000 EVS ISL C9 ADV DIA MET MS Transmission to be provided with I O pack 119 for rescue interlock Transmission Cooling Sys 3000EVP ISL ADV MET MS Trans Fluid Synthetic TES295 3000EVS Trans Mode Button Programmed 4thStartup 5thMode gt Transmission EVS Series 5Yr Std Warranty Transmission Service Manual Allison 3000 EVS gt Alternator 270Amp Leece Neville C7 C9 C11 C13 S60 CAT Engine Manual gt Engine Oil Level Check Electronic N A w CAT Eng DIA G
59. and body with stainless steel machine screws A polyester barrier film gasket shall be placed between stainless steel hinge and any dissimilar metals as necessary Drip rails shall be installed above all compartment door openings Drip rails shall be fastened with stainless steel screws These drip rails shall be completely removable for easy replacement if necessary The latching of compartment doors shall be with stainless steel 6 Hansen offset bent D ring keyed handles A gasket shall be placed between stainless steel handle and door Door latches shall be a double catching two point top and bottom rotary slam latch recessed inside the double panel door with striker plate All vertically hinged compartment doors shall have a pneumatic cylinder to hold door in the open and closed positions Each door shall be capable of being closed without unlatching Door checks shall be bolted to the upper compartment door header and the box pan of the door Door checks that require unlatching by hand will NOT BE ACCEPTABLE SVI 603 03 27 07 Page 41 of 86 Maui Police Department SVI Trucks Production Specification CO 3 BODY HEIGHT MEASUREMENTS The vertical body dimensions shall be as follows AHEAD OF REAR AXLE Description Dimension A Bottom of Subframe to Top of Body 89 0 B Bottom of Subframe to Bottom of Body 25 0 C Vertical Door Opening Short Compartment with hinged door 20 0 BEHIND REAR AXLE Description Dimension D Bottom of Subfr
60. and constructed the same as the seat CURBSIDE INTERIOR AREA SLIDE OUT EXTENSION There shall be one 1 slide out section s which shall extend approximately 32 as measured from the outside of the body The extendable module shall be approximately 84 in length and the interior height shall be approximately 9 less that the interior height of the body walkway The installed module shall provide a water tight seal in both the fully extended and the retracted positions The slide out section shall utilize smooth operating quiet gear and rack system Systems using hydraulic components will NOT BE ACCEPTABLE There shall be only two 2 serviceable items the 12 vdc motor and the electric control switch The system shall use a heavy duty positive 100 synchronized gear and rack system to prevent binding during the extend or retract cycle The rack system shall be rated for up to 1 500 pounds A 3 position momentary type rocker switch shall be used to operate the slide out wall system A manual override shall be provided in the event of a system failure The slide out section shall be framed with 2 x 2 x 1 4 6061 T6 alloy aluminum The frame structure shall be covered with no less than 1 8 thick 3003 H14 smooth aluminum There shall be two 2 flashing LED warning lights with red lenses one at each end of the slide out section The lights shall activate and be visible when the unit is extended All electrical wiring installed in the sli
61. binet with two 2 runs of coaxial cables terminated with F connectors in streetside data rack to the exterior curbside rear wheel well area patch panel location DATA NETWORK WIRING The pre wiring for a data network shall be provided and installed All cables shall be stranded CAT6 run in wire raceways to each location identified below and terminated in RJ45 receptacles All external receptacles shall be waterproof outdoor type All cable runs shall home run to the lower portion of streetside data rack RJ45 patch panel A wireless 802 11b g router shall be provided in lower portion of data rack and external antennas provided on roof of the vehicle Locations as follows Four 4 runs to Dispatchers position in cab two 2 runs per location Sixteen 16 runs to the Operators positions in the forward Command Area two 2 runs per location Four 4 runs to the Operators positions in the rear Conference Area two 2 runs per location Four 4 runs to the watertight communications access panel on curbside rear wheel well area System server shall be mounted in the 19 data rack located in rear cab area adjacent to Dispatcher position SVI 603 03 27 07 Page 84 of 86 Maui Police Department SVI Trucks Production Specification CO 3 COMPUTER WORKSTATIONS Four 4 customer supplied computers shall be installed one at each operations area slide out workstation PRINTER Install customer supplied HP 2600DN or equal printer in Dispatch are
62. body heat build up The armrests shall be independently adjustable with settings that pivot inward 17 5 degrees for keying and outward 15 degrees Arm height adjusts independently within a four inch vertical range The stock Herman Miller caster wheel assembly shall be removed and the base of the stock pedestal shall be affixed to the glider mechanism recessed in the slide out floor The base of the chair pedestal shall be attached to a custom manufactured glider base that will allow up to 7 inches of fore and aft positioning The glider base shall not require a mechanical lock or release devices to slide AM FM RADIO An AM FM radio shall be located in streetside slide out with recessed cieling mounted speakers SVI 603 03 27 07 Page 59 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CURBSIDE INTERIOR AREA IC3 DATA RACK A Middle Atlantic Products roll out and rotating model WR 37 32 with 37 rackspaces shall be provided directly behind wall between central communications and rear conference area on streetside Overall dimensions of rack shall be 76 6 H x 24 W x 32 8 D Useable height shall be 64 7 rackspaces useable depth shall be 26 Rack shall be fully welded construction and provide a 750 lb weight capacity with proper distribution Rack shall be constructed of steel and finished in a durable black powder coat paint The WR shall have a solid locking rear door and have a removable rear e
63. braking and reduced stopping distance in skid conditions The electronic monitoring system shall incorporate diagonal circuitry to monitor wheel speed during braking through a sensor and tone ring on each wheel A dash mounted vacuum formed ABS composite lamp shall be provided to notify the driver of a system malfunction A momentary test switch shall be installed to test the system for diagnostic codes The vacuum formed ABS composite system shall automatically disengage the auxiliary braking system device when required The Meritor Wabco vacuum formed ABS composite system shall have a three 3 year or 300 000 mile warranty provided by Meritor Wabco Vehicle Control Systems REAR TIRES The rear tires shall be Michelin 11R 22 5 16PR H tubeless radial XZE highway tread with a minimum rating of 24 020 pounds REAR WHEELS ALCO ALUMINUM The single rear axle wheels shall be Alcoa hub piloted 8 25 x 22 5 polished aluminum wheels OIL LUBRICATED REAR WHEEL BEARINGS The rear axle shall have oil lubricated wheel bearings SVI 603 03 27 07 Page 14 of 86 Maui Police Department SVI Trucks Production Specification CO 3 REAR SUSPENSION The rear single axle suspension shall be an Aero Glide air suspension with a single air bag on a tapered forged drop leaf spring with adjustable torque rods and shock absorbers Dual air height control valves shall be installed to insure equal frame height on both sides of the vehicle regardless of the
64. ce The cabinet shall be approximately 28 wide x 16 deep x 38 high and consume the area from the door to rear wall There shall be one 1 vertically adjustable shelf shelves in each of the above cabinets It shall have a 1 25 lip to contain items while minimizing space used There shall be one 1 perminate shelf shelves located rear curbside wall for Maui Police Department supplied fax machine It shall have a 1 25 lip to contain items while minimizing space used MAGNETIC WHITEBOARD There shall be one 1 magnetic whiteboard surface s as large as possible located in the cab command area on streetside wall above desk DATA RACK A Middle Atlantic Products model MRK 2426 with 24 rackspaces shall be provided on curbside of L Desk behind passenger seat Overall dimensions of rack shall be 48 12 H x 22 W x 26 4 D Useable height shall be 42 2 rackspaces useable depth shall be 24 Rack shall be fully welded construction and provide a 2 500 Ib weight capacity Rack shall be constructed of steel and finished in a durable black powder coat paint The MRK shall have a solid locking rear door and have a removable rear electrical knockout panel installed in base and removable rear electrical knockouts with N type connectors for UHF VHF antennas installed in top if necessary A 1 4 20 threaded grounding and bonding stud shall be installed in base of enclosure Rack shall be warranted to be free from defects in ma
65. ch and switch solenoid shall be supplied and installed by the cab chassis manufacturer BATTERY SOLENOID Battery switch shall consist of a minimum 200 ampere constant duty solenoid to feed from positive side of battery BATTERY CHARGER One 1 Xantrex model XC5012 battery charger with 120 VAC input and 50 amp 12 volt output shall be provided This system shall have a multiplex charging mode which employs the 3 stage charging algorithm Bulk Absorption and Float During the Bulk stage the battery is accepting high current In the Absorption stage the battery voltage is held constant and the current declines Finally in the Float stage the charger continues to provide voltage at a lower level to maintain the battery in a fully charged state If there is no load on the battery it will typically draw very little current The charger however is able to provide current to its full rating to power DC loads on the battery In float if batteries are very new or a battery is on the low end of the size range and if it is fully charged to the point where it will not accept any more current then the charger will enter an adaptive float no float behaviour where it shall alternate between float charging flo and resting the battery rdy A remote bar graph type indicator panel shall be provided for showing status of battery charger The charger shall have a EMC FCC Class B Approval NO EXCEPTIONS SHORE POWER PLUG One 1 Kussmaul 30 amp Super Auto Ej
66. ch will illuminate the headlights to 80 brilliance when the master switch is in the On position and the parking brake is released FLAT FRONT GRILLE GLADIATOR EVOLUTION A two 2 piece hinged stainless steel flat front grille contoured to shape of front fascia shall be installed on the front of the cab The upper portion of the grille will be hinged and will have two 2 flush push button latches that allow access to the front fluid fills of the cab Included are two 2 chrome vacuum formed ABS composite intake grilles located outboard of the stainless steel grille Additional air intake openings are supplied in the front fascia located below the stainless steel grille A minimum total free air intake of 677 0 square inches shall be provided See attached PDF file for clarification CAB MIRRORS Two 2 Ramco model 9000 FFHR 800HR bus style mirror heads shall be mounted on the cab doors The heated full face flat glass and heated convex mirrors on top of the mirror heads shall be remote controlled with switches on the dash The mirrors shall be attached to chrome plated cast aluminum arms The mirror head backs are chrome plated injection molded ABS composite SVI 603 03 27 07 Page 10 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CAB CRASH TEST ECE 29 Spartan Chassis Inc has successfully submitted their extruded flat floor cab to the International crash test ECE 29 Addendum 28 revision 1 As part of the ECE
67. ck up lights TRANSMISSION TOUCH PAD An Allison pressure sensitive range selector touch pad shall be provided and located to the right of the driver within clear view and reach DRIVELINES All drivelines shall be Spicer 1710 heavy duty series with glide coat splines on all slip shafts MULTIPLEX ELECTRICAL SYSTEM WITH COLOR DISPLAY A Weldon multiplex electrical system shall be supplied The system shall be a single starting type installed per NFPA 1901 The electrical system shall be 12 volt suppressed per SAE J551 with six 6 Douglas BCI 31 950 CCA batteries with 210 minute reserve capacity and 3 0 welding type dual path starter cables per SAE J541 The Multiplexed wiring system shall include the following Dash or engine tunnel mounted information center with approximately 4 H 92mm x approximately 6 W 159mm color LCD screen Systems Diagnostic Menu and controls Solid state switching Complete Peer to Peer network architecture Weatherproof Nodes and sealed Deutsch connectors Sequences and sheds electrical loads The Vista Ill Display Node shall include the following features Automatic climate control when an air conditioning system is ordered Outside temperature display A real time clock with display Three 3 programmable video inputs A useable temperature range from 40 degrees to 185 degrees F Unlimited virtual switches Selectable font sizes types and colors for optimum user effic
68. coat paint The WR shall have a solid locking rear door and have a removable rear electrical knockout panel installed in base and removable rear electrical knockouts with BNC knockouts for UHF VHF antennas installed in top A 1 4 20 threaded grounding and bonding stud shall be installed in base of enclosure Rack shall be warranted to be free from defects in material or workmanship under normal use and conditions for the lifetime of the product In addition the WR shall be provided with model WRFD 37 reinforced 16 gauge solid steel front door Integrated fan tops with proportional speed thermostatic fan control and Vertical outlet strip model PD 2415SC NS A minimum 37 amp UPS uninterruptable power supplies with surge protection shall be located in data rack An exterior body hinged door shall be provided allowing access to rear of data rack Door shall be capable of swinging past 90 degree and be provided with keyed lock SVI 603 03 27 07 Page 57 of 86 Maui Police Department SVI Trucks Production Specification CO 3 STREETSIDE INTERIOR AREA IS4 INTERIOR BENCH SEAT The interior rear streetside corner of body shall be provided with a bench seat located above the exterior Compartment S3 Seat will be approximately 150 wide extending full width of Conference Area The seat shall be fabricated of 3 4 exterior grade plywood with 3 thick foam and heavy duty vinyl covering The seat backrest shall be approximately 12 high x 2 thick
69. compartment with flexible hose and plug The drain shall be located where easily accessible for generator service FUEL SYSTEM The generator fuel system shall be plumbed to the chassis main fuel tank A separate fuel line shall be installed directly from the tank not connected to the truck engine fuel line system the generator fuel line shall be properly protected and secured inside of chassis frame A shut off valve shall be provided between the generator and fuel line as it enters the compartment STARTING SYSTEM The generator starting system shall be powered by chassis battery system with heavy duty stranded copper cables The starter line shall by pass the chassis master switch to permit generator operation when the apparatus engine is not running This starter line shall be of sufficient size for the generator adequately protected and supported inside the chassis frame area SAFETY SHUTDOWNS The generator shall be equipped with the following safety functions for protection of the generator unit High Temperature Shutdown Low Oil Pressure Shutdown SVI 603 03 27 07 Page 69 of 86 Maui Police Department SVI Trucks Production Specification CO 3 COOLING Since the generator is air cooled the ventilation of the generator is crucial The installation shall permit operation of the unit both while the apparatus is stationary or while it is in motion The cooling air flow shall be though stamped louvers in compartment walls or doo
70. connected from the unit a quick 20 millisecond maximum transfer takes place 16 ms typically and the PROsine 3 0 Inverter Charger begins inverting delivering AC power to the loads When utility AC becomes present again the control circuit waits for 8 seconds during which time the unit verifies the stability of the AC source and synchronizes the inverter to the AC source for a smooth seamless transfer Battery charging will begin and AC is also fed through the unit to power the AC loads SVI 603 03 27 07 Page 75 of 86 Maui Police Department SVI Trucks Production Specification CO 3 Advanced Control System ACS panel included with the PROsine 3 0 The ACS Control Panel provides system control and display information via a menu driven 6 level multi functional LCD panel Detailed information and control is available for AC information battery status inverter mode charger mode system info and Xantrex info The deluxe ACS Remote Control Panel is included with the PROsine 3 0 Inverter Charger unit There s no need to pay extra for remote monitoring and control 120 240 VOLT WIRING SYSTEM The complete wiring and electrical installation shall conform to present National Electrical Code and the National Fire Protection Association standards The wiring electrical fixtures and components shall be to the highest industry quality standards available on the market The equipment shall be the type as designed for mobile type installations subj
71. d wiper high quality camera and lens The camera system shall be a high resolution unit with Lowlighta color technology and a 176X zoom lens 22X optical 8X electronic There shall be one Pelco KBD300 joystick controller and CM6700 controller TELESCOPING PNEUMATIC MAST The apparatus shall be equipped with one 1 Will Burt 7 30 heavy duty pneumatic powered telescoping mast s The mast shall utilize air from the chassis brake system Air to operate the telescoping mast must be drawn from a drier system and be regulated to 20 psig and shall have a back pressure protection valve This valve shall hold back 70 pounds in the air brake system and shall only allow air to pass into the system when the ignition switch is on and the parking brake is set A red flashing warning light will be visible to the driver to warn when a light tower is out of roof nested position A pneumatic kit to raise and lower the mast shall include air control valve 0 160 psig air gauge regulator 0 30 psig air gauge The mast shall be of a free standing design non guyed and use high strength heat treated aluminum alloy tubes and collars Each mast section tube shall have two full length external keys and nominal 095 wall thickness collars with matching keyways to maintain directional azimuth Each mast section and collar shall be of the low friction synthetic bearings for smooth operation and longer life Bumpers shall be supplied to reduce shock on extension and r
72. d Clear Coat Buffed Finish Operators amp Parts List Manual 1 Set Engine amp Transmission Operation Manual 1 Fire Extinguisher 2 5 Kit Road Safety Chassis Discount Chassis Preparation 2005 400 06 24 05 Chassis Interest Chassis Handling Custom Chassis Delivery Walk in Rescue Side Lower Comp ts 2005 400 06 24 05 CHASSIS Chassis Options Custom Front Bumper As Provided by Cab Chassis Custom Bumper Gravelshield Cab Chassis Supplied Air Horn s Cab Chassis Supplied Exhaust As Provided by Cab Chassis Batteries Add Battery s Cellular Phone Antenna Installation Radio Antenna Mounting Installation Paint Cab Cab Chassis Supplied Mudflaps Automatic Vehicle Leveling System Leveling System Interlock Window Tint 5 Cab Command Center Rear Cabinet 38 High Hinged Doors Interior Cabinet Shelf Perminate Shelf lt n a a a a a a a a a a a a a a a aa DON ee ee ee oO Oo pe see st Oeaes I ON ODMH HaHa a 2 020 42 42422244 k 03 27 2007 PART NO 10 S9 0110 MB 20 1000 MB 20 1010 MB 20 1310 MB 22 1400 MD 20 3010 CZ A0 2250 MD 50 8000 MD 50 8100 A0 82 A010 MD 20 1010 MD 20 3021 N7 24 100S N7 26 0100 AO0 12 1170 A0 21 4100 A0 26 2100 A0 31 1100 A0 40 1120 A0 61 1240 AO0 6A 1110 AO 6B 1100 A0 80 1200 AO0 81 1010 AO 81 2010 A0 82 1010 P1 10 1100 P1 25 1100 P1 Z0 1100 P1 A0 1100 P1 Z0 2000 P2 20 1100 P2 05 1010 P2 C0 1010 P2 70 2240 P3
73. d bulb incandescent lighting under each cab door The lights will be activated by either a single switch on the dash or each respective door switch Alternating Headlights An alternating high beam headlamp flashing system shall be installed into the high beam headlamp system that will allow the high beams to flash alternately from left to right The completed system shall be capable of using high beam to override flashing function and will flash high beams only when the low beam headlamps are selected Audible Alarm for Open Door Light An audible alarm shall be wired to the open door light which will sound when a door is open and the air brake is off with the vehicle in gear ROCKER SWITCH CONSOLE A three 3 section double row switch console shall be provided and shall be an integral part of the engine tunnel with easy switch access to both the driver and officer The console will consist of an angled driver s side panel center main panel and angled officer s side panel The switch console shall not be an add on type console OFFICER ROCKER SWITCH PANEL The officer s side switch panel shall be equipped with a color Mux Vista display DRIVER ROCKER SWITCH PANEL The color Mux Vista display will be mounted in the right hand side of the panel The driver s side panel shall include a rocker type headlight switch with instrument lamp slide dimmer intermittent windshield wiper washer switch and secondary braking device rocker switches
74. d with 2 x 2 tubing in order to support a person sitting on the edge of the desk The desk top surface shall be fabricated of 3 16 smooth aluminum with a 2 vertical back splash along the back edge and a 2 vertical downward edge along the front to cover the 2 x 2 reinforcement There shall be 2 1 2 diameter holes with plastic edge grommets provided at each rear corner for wiring of future equipment located on the desk top Two 2 120 volt electrical outlet s shall be provided at the two 2 seated positions at the desk INTERIOR PEDESTAL SEAT Two 2 Bostrom Sierra high back vinyl pedestal type seat s with 6 fore aft adjustment shall be provided on the completed apparatus Each seat shall be mounted on a swivel style pedestal base and securely bolted to the reinforced floor structure The seat shall closely match the driver and officer seat colors Black The above specified seat s shall be provided with an automotive type lap seat belt The seat belt s shall be secured to the attachment point provided on the seat and shall be red FUEL FILL There shall be one 1 Cast Products fuel fill door located in the streetside exterior wheel well panel behind the rear axle The fill door shall have a latching hinged door and a permanent label with the text DIESEL FUEL ONLY DRI ERASE MARKER MAGNATIC BOARD Two 2 Dri Erase Magnetic Board s shall be provided Boards shall be custom fabricated from smooth steel sheet metal and painted B
75. de out wall shall run through a boxed type conduit at the lower corner of the system All wiring shall be enclosed in a flexible moisture resistant reinforced conduit with proper seal tight connectors and hardware Access shall be provided for inspection of all wiring and the gear and rack mechanism The Command Center Slide out must be able to withstand years of rugged service and wear For this reason this design metal thickness and attachments must be strictly adhered to RV type slide outs or slide outs using light weight metal or fiberglass shall not be acceptable There shall be a removable desk storage area in the lower portion of the exterior wall of the slideout WINDOW One 1 18 wide x 22 high vertical sliding window shall be installed in the forward facing wall of the slide out module WINDOW One 1 18 wide x 22 high vertical sliding window shall be installed in the rearward facing wall of the slide out module SVI 603 03 27 07 Page 58 of 86 Maui Police Department SVI Trucks Production Specification CO 3 INTERIOR CABINET OVERHEAD There shall be two 2 overhead cabinet s provided on interior Cabinet s shall be constructed of 1 8 smooth finish aluminum and painted with a hammer tone powder coat paint finish for a hard durable surface Paint color shall be gray or black Each cabinet shall be approximately insert actual dimensions The above cabinet s shall have sliding Lexan doors INTERIOR DESK The in
76. doors shall have a full power window 27 00 x 26 00 with a total glass area of 702 square inch each The rear doors shall have a power window 27 50 x 26 00 with a total glass area of 715 square inch each The driver shall be able to control all windows The officer and crew area windows shall have individual controls FABRIC COVERED SEATS DURABLE BALLISTIC POLYESTER The seats shall be covered with a high strength wear resistant fabric of durable ballistic polyester A PVC coating is bonded to the back side of the material to help protect the seats from UV rays and from being saturated or contaminated by fluids SVI 603 03 27 07 Page 8 of 86 Maui Police Department SVI Trucks Production Specification CO 3 BLACK SEAT COLOR All seats supplied on the chassis shall be black in color SEATBELT WARNING SYSTEM A seatbelt use warning system shall be installed in the chassis The system will provide a visual and audible warning when all of the following conditions are met 1 Any seat is occupied sixty pounds minimum 2 The corresponding seat belt s remains unfastened 3 The park brake is released Once activated the visual and audible indicators will remain active until all occupied seats have the seat belts fastened DRIVER SEAT The driver s seat shall be an eight way electric H O Bostrom Sierra high back seat and shall include a tapered and padded seat cushion and back with mechanical suspension The seat shall be an ABTS
77. dy roof along roof radius for securing tarps or aerial antennas ROLL OUT AWNING CURBSIDE A heavy duty canopy awning shall be installed on the apparatus body The awning shall be approximately 14 feet long with approximately 8 of extension length The awning shall be manufactured with satin finish extruded aluminum arms and braces The arm channels shall utilize nylon bearings for a smooth operation Awning shall lock while in stored position to prevent any rattling during travel Awning shall lock and unlock with a remote brake control located on awning arm not requiring the use of a wand Features of the awning are Built in Thin Lite 12 volt amber fluorescent light Awning hangers Built in awning tie downs to hold awning steady in a breeze Durable multi layer laminated vinyl fabric that resists scratches stains fading and mildew Alumaguard metal wrap cover The awning color shall be Natural 8604 ROLL OUT AWNING A heavy duty canopy awning shall be installed on the curbside slideout of the apparatus body The awning shall be manufactured with satin finish extruded aluminum arms and braces The arm channels shall utilize nylon bearings for a smooth operation Awning shall lock while in stored position to prevent any rattling during travel Awning will lock and unlock with a remote brake control located on awning arm not requiring the use of a wand Features of the awning are Built in Thin Lite 12 volt amber fluorescent light
78. e For prolonged operation the compartment doors must be open EXHAUST SYSTEM The generator exhaust system shall be equipped with a residential type muffler for maximum quieting and black iron rigid pipe to link the generator to the muffler The exhaust pipe shall be securely supported and shall be shielded or insulated to prevent excessive heating of the compartment MANUALS AND SCHEMATICS Two 2 complete manuals on parts list maintenance wiring schematics hydraulic schematics circuit boards voltage regulator board and other components shall be provided on delivery GENERATOR COMPARTMENT INSULATION The generator compartment shall be provided with heavy duty sound insulation applied to walls and ceiling Insulation shall have a high temperatures rating with a foil facing and attached to walls with a positive type fasteners glue type adhesive shall not be acceptable GENERATOR INSTRUMENTS AND CONTROLS To properly monitor the generator performance and load demand during operation a metering panel shall be provided on the apparatus This panel shall be located near the circuit breaker panel The installation shall be equipped with the following instruments Voltmeter Ammeter per line Hourmeter accumulated run time Frequency meter GENERATOR CONTROLS In addition to generator controls provided at the generator there shall be controls provided in the cab at the 12 volt control panel The following controls shall be
79. e Stripe Body 6 Wide Stripe Color White Stripe Layout Straight Reflective Stripe Cab 6 Wide Custom Lettering Lettering Budget 5 000 Interior Finish Zolatone Door Details RU std Alum Hinged Doors 3 16 Interior BODY HEIGHT Body Height 25 Raised Roof for Walk in BODY WIDTH Body Width 100 0 Wide STREETSIDE FORWARD Compartment S1 WI Width 64 0 60 0 S2S 57 0 DO LOW Hinged Door 3 16 Unpainted Interior Panel Horiz Hinge Hinged Door Handle D ring w lock All cab and body exterior compartment D ring locks shall be keyed alike Hinged Door Closure Tailgate Style Compartment Options Hinged Compartment Lights 1 OSS LightStick lower comp t only STREETSIDE INTERMEDIATE Compartment S2 WI Width 64 0 60 0 S2S 57 0 DO LOW Hinged Door 3 16 Unpainted Interior Panel Horiz Hinge Hinged Door Handle D ring w lock PPMP PND Ce i i A o A l A A A A A A A A A A A l l A A A A d A d Md RENN CEES OO EEE GEE CUES CEES A 03 27 2007 PART NO CZ 32 1230 CZ A0 1010 CZ A0 2210 CZ A0 2Z10 FO BO 1120 F1 10 0100 NO A2 1310 A5 30 1100 CZ 10 2910 CZ 30 5000 CZ 32 1110 CZ 32 1210 CZ A0 1010 CZ A0 22A0 NO A2 1210 B1 30 1100 CZ 10 2810 CZ 30 5100 CZ 32 1110 CZ 32 1230 CZ A0 1010 CZ A0 2140 CZ A0 2Z10 NO A2 1210 F1 10 0100 B2 30 1100 CZ 10 2810 CZ 30 5100 CZ 32 1110 CZ 32 1230 CZ
80. e regulator set point and the lowest charge current is maintained for ten 10 minutes Failure of any of these tests shall require a repeat of the sequence RESERVE CAPACITY TEST The engine shall be started and kept running until the engine and engine compartment temperatures are stabilized at normal operating temperatures and the battery system is fully charged The engine shall be shut off and the minimum continuous electrical loads shall be activated for ten 10 minutes All electrical loads shall be turned off prior to attempting to restart the engine The battery system shall then be capable of restarting the engine Failure to restart the engine shall be considered a test failure ALTERNATOR PERFORMANCE TESTS TEST AT IDLE The minimum continuous electrical load shall be activated with the engine running at idle speed The engine temperature shall be stabilized at normal operating temperature The battery system shall be tested to detect the presence of battery discharge current The detection of battery discharge current shall be considered a test failure TEST AT FULL LOAD The total continuous electrical load shall be activated with the engine running up to the Engine Manufacturer s governed speed The test duration shall be a minimum of two 2 hours Activation of the load management system shall be permitted during the test However an alarm sounded by excessive battery discharge as detected by the system required to notify apparatu
81. e shall be constructed directly on the chassis The chassis frame rails shall be fitted with 5 16 x 2 fiber reinforced rubber to isolate the body frame members from direct contact with chassis frame rails The body subframe shall be constructed from 6061T6 aluminum alloy tubing Subframe shall consist of two 2 2 x 6 x 1 4 aluminum tubes the same width as the chassis frame rails NO EXCEPTION Welded to this tubing shall be crossmembers of 2 x 6 x 1 4 aluminum These crossmembers shall extend the full width of the body to support the compartments Crossmembers shall be located at front and rear of the body below compartment divider walls and in front and rear of wheel well opening Additional aluminum crossmembers shall be located as necessary to support walkway or heavy equipment To form the frame the tubing shall be beveled and welded at each joint using 5356 aluminum alloy welding wire SVI 603 03 27 07 Page 37 of 86 Maui Police Department SVI Trucks Production Specification CO 3 BODY MOUNTING The body subframe shall be fastened to the chassis frame with a minimum of eight 8 spring loaded body mounts Each mount shall be configured using a two piece encapsulated slide bracket The two 2 brackets shall be fabricated of heavy duty 1 4 thick steel and shall have a powder coat finish to prevent any corrosion Each mounting assembly shall utilizing two 2 5 8 diameter x 6 long grade L9 bolts and two 2 heavy duty springs T
82. e within thirty 30 days of ownership transfer To maintain warranty coverage the proper ownership transfer papers shall be kept on file at Manufacturer s facility In the event of a chassis remount this structural warranty shall remain in effect providing that the re chassis work is completed by the Manufacturer or a facility which obtains written authorization from the Manufacturer Should repairs become necessary under the terms of this warranty the extent of the repair shall be determined solely by the Manufacturer and shall be repaired by the Manufacturer or an Authorized Service Center designated by the Manufacturer The expense of any transportation to or from the ASC shall be the responsibility of the Maui Police Department and is not an item covered by this warranty There shall be a Warranty Certificate supplied with the completed apparatus to detail the warranty configuration SVI 603 03 27 07 Page 4 of 86 Maui Police Department SVI Trucks Production Specification CO 3 TESTING 12 VOLT DC NFPA TEST The apparatus low voltage electrical system shall be tested and certified by the manufacturer per NFPA 1901 The test shall be performed with the air temperature between 0 degrees F and 110 degrees F TEST SEQUENCE The following three 3 tests shall be performed in the order indicated below Before each test the batteries shall be fully charged A full charge condition shall be when the charge voltage stabilizes at the voltag
83. ead from 5 to 85 MPH 5 to 140 KPH The odometer shall display miles One 1 three function gauge with primary air pressure secondary air pressure and fuel level The scale on the air pressure gauges shall read from 0 to 140 pounds per square inch PSI The air pressure scales shall be non linear to expand the scales in the region of normal operation The scale on the fuel level gauge shall read from empty to full One 1 four function gauge with engine oil pressure coolant temperature transmission oil temperature and a voltmeter The scale on the engine oil pressure gauge shall read from O to 140 pounds per square inch PSI The engine oil pressure scale shall be non linear to expand the scale in the region of normal operation The scale on the coolant temperature gauge shall read from 100 to 250 degrees Fahrenheit F The scale on the transmission oil temperature gauge shall read from 100 to 300 degrees Fahrenheit F The scale on the voltmeter shall read from 8 to 16 volts The instrument panel shall contain an Annunciator Module that contains the following indicator lights All indicator lights shall contain LED lamps RED LAMPS Stop Engine indicates critical engine fault Park Brake indicates park brake is set Low Fuel indicates low fuel Cab Ajar indicates tilt cab is not locked down 1 Volts indicates high or low system voltage Low Oil Press indicates low engine oil pressure High Coolant Temp indicates exces
84. ect shore power plug s shall be furnished and installed wired to the specified Fleet Power 2500 12 inverter cahrger unit The shore power connection shall automatically disengage from vehicle when chassis ignition is engaged The Auto eject outlet cover shall be white The shorepower plug receptacle shall be located above genrator compartment door ENGINE COMPARTMENT LIGHT Engine compartment light s shall be supplied and installed by the cab chassis manufacturer for illumination during service and maintenance SVI 603 03 27 07 Page 63 of 86 Maui Police Department SVI Trucks Production Specification CO 3 MAP LIGHT There shall be six 6 24 goose neck 12 volt map light s furnished and installed in the interior body The exact location shall be Two 2 at cab dispatch ceiling Two 2 one at each streetside OPS slide out position Two 2 one at each curbside OPS slide out position CAB HAZARD WARNING LIGHT A red HAZARD warning light shall be supplied and installed by the cab chassis manufacturer Light shall illuminate automatically to warn the Driver of the following when the apparatus parking brake is not fully engaged Any passenger or compartment door is open Equipment rack is not in stowed position Light tower is extended The light shall be labeled DO NOT MOVE APPARATUS WHEN LIGHT IS ON BACK UP ALARM An electronic backup alarm shall be supplied and installed by the cab chassis manufacturer The backu
85. ect to vibration moisture and severe continuous usage The following electrical components and wire shall be the minimum acceptable standard for this type of apparatus Wiring All electrical wiring shall be fine stranded copper type THHN The wire shall be sized to load and circuit breaker rating Wiring shall be color coded and printed with function every 3 for easy identification Conduit All 120 240 volt wiring in the apparatus body shall be through flexible moisture resistant reinforced conduit with proper seal tight connectors and hardware Labeling of Equipment All circuit breakers shall be labeled to indicate purpose Metal engraved or plastic coded labels shall be provided for all exterior and interior outlets indicating output amperage Schematic An As Built electrical wiring diagram schematic will be supplied with the completed apparatus 120 240 VOLT SCENE LIGHTING FRONT CAB MOUNTED FLOODLIGHT One 1 Fire Research Focus 500 watt 120 volt quartz floodlight s shall be provided on the front face of the chassis cab Each light shall be mounted in a Brow style housing Each light shall be wired directly to the electrical generator system with Carflex conduit and stranded copper wire The floodlights shall be protected with circuit breakers rated at the proper amperage and wire size Make Fire Research Model Focus P N FCA800 S50 There shall be one 1 switch to control the above scene lights The switch shall be located
86. ed by the manufacturer per NFPA 1901 Certification shall be provided with delivered apparatus The test shall be performed with the air temperature between 0 degrees and 110 degrees F TEST SEQUENCE The following test shall be performed in the order indicated below The wiring and permanently connected devices excluding utilization devices are subjected to 900 VAC for one 1 minute The test is conducted between live parts and the neutral conductor as well as between the live parts and the vehicle frame with any switches in the circuit closed The test is accomplished with a Biddle HiPot tester model 230315 The generator output is tested at 100 of its nameplate rating for a minimum of two 2 hours into a resistive load The following information is recorded of the generator and its power supply at thirty 80 minute intervals during the test voltage amperage and frequency output of the generator as well as the oil pressure water temperature transmission temperature hydraulic temperature and the battery charge rate as applicable INSPECTION TRIPS The Manufacturer shall provide nine 9 individual inspection trips to the factory where the apparatus will be built The cost of transportation food and lodging shall be borne by SVI Trucks The trips shall be configured as follows Three 3 Maui Police Department members for a preconstruction conference Three 3 Maui Police Department members for a pre paint inspection Three
87. erating components All manufacturers warranties apparatus amp equipment shall be furnished and indicated in the manufacturer s bid Any standard warranties including but not limited to engine transmission tires and axles furnished by the original equipment manufacturer OEM or the prime contractor will be passed on to the Maui Police Department Also include any available extended warranties that will start after the initial warranty period Goods or property shall be as represented by these specifications as well as additional agreements as a result of discussions regarding these specifications and shall be as promised with implied liability on the manufacturer The Body Manufacturer must be the single source coordinator of all warranties on the vehicle STRUCTURAL WARRANTY TEN 10 YEARS The Manufacturer shall warrant that each new rescue body exclusive of paint finish hardware moldings windows and other appointments and accessories is structurally sound and free of all structural defects of both material and workmanship and further warrants that it will maintain such structural integrity for a period of ten 10 years from the completion date listed on the Manufacturer s data plate attached to the vehicle inside the cab The Manufacturer further warrants that this structural integrity warranty may be transferred to a second Purchaser providing the vehicle is inspected by the Original Manufacturer or their authorized representativ
88. es shall be black flush paddle type which are incorporated into an upper door panel The front doors shall measure 43 00 wide x 77 00 high with 13 thick aluminum skins The front steps shall be a two 2 step configuration with the lower step constructed of an open grate material and the intermediate step shall be covered with embossed NFPA compliant aluminum tread plate The following measurements shall apply First step 11 44 deep x 31 13 wide Intermediate step 8 75 deep x 33 00 wide Ground to first step approximately 21 00 First step to intermediate step 11 00 Intermediate step to floor 11 00 The rear doors shall measure 34 00 wide x 97 00 high with 13 thick aluminum skins The rear steps shall be a two 2 step configuration with the lower step constructed of an open grate material and the intermediate step covered with embossed NFPA compliant aluminum tread plate The following measurements shall apply First step 12 13 deep x 20 44 wide Intermediate step 10 50 deep x 23 00 wide Ground to first step approximately 21 00 First step to intermediate step 12 50 Intermediate step to floor 12 50 DOOR HANDLES EXTERIOR CHROME The cab door exterior pull handles 4 shall be extruded aluminum with a polished chrome plated finish Each handle shall include an aluminum scuff plate with a polished chrome finish The scuff plate shall be 6 25 tall x 10 50 wide FRONT AND REAR POWER DOOR WINDOWS The front
89. etraction All exterior aluminum surfaces shall be anodized and sealed Fasteners and fittings shall be plated steel or stainless steel for corrosion resistance Mast shall be mounted using an internal roof mounting kit One 1 maintenance and instruction manual will be provided for the towers on delivery Wiring schematic air piping schematic and installation diagrams shall be provided with the manual Manufacturer s blueprint of tower complete parts list and bill of materials for towers provided with manuals MODEL 7 30 SPECIFICATIONS Nested height tower only 6 8 Extended height tower only 29 1 Normal payload capacity 150 Ibs Number of sections 6 Tube Diameter 6 3 4 3 Mast Volume 3 2 cu ft Collar type Non locking Maximum operating pressure 35 psi SVI 603 03 27 07 Page 78 of 86 Maui Police Department SVI Trucks Production Specification CO 3 PNEUMATIC KIT A pneumatic kit air control assembly without compressor shall be provided to control the mast The assembly includes a 0 160 PSIG air gauge regulator 0 30 PSIG air gauge and a 3 8 inlet air hose with NPT fittings to provide air from air source NYCOIL WIRING 7 30 A 30 Nycoil conduit measuring 1 ID x 16 1 2 OD coil shall be provided for the 7 30 telescopic mast A mast bucket shall be provided to hold the Nycoil below the roof line of the truck The bucket shall be fabricated from 125 smooth aluminum with welded water tight seams The bucket
90. frequency shall be stable at 60 hertz Generator features shall include 93 cylinder diesel engine Fused DC circuits Permanent magnet alternator Automotive type starter Digital voltage regulation with no Overvoltage low oil pressure overtemp overspeed adjustments required and overload safeties Integral enclosed muffler 10A battery charging USDA approved spark arrestor Hourmeter Internal radiator Waterproof connector for remote operation Sound insulated cover Electric fuel pump Intake silencer Fuel filter Heavy duty air cleaner Full flow oil filter Maintenance free electronic governor Automatic timed glow plugs for quick easy start Overall size of generator shall 36 L x 24 W x 22 H and weigh 420 lbs WARRANTY PERIOD Provided such goods are operated and maintained in accordance with Onan s written instructions Onan warrants that the CMQD Quiet Diesel Series Generators shall be free from defects in material and workmanship for a period of two 2 years or two thousand 2 000 hours whichever comes first from the date of delivery to the first purchaser GENERATOR MOUNTING The generator shall be mounted on rubber vibration isolators The compartment shall be reinforced where necessary to hold weight of generator A valve shall be provided on the generator oil drain outlet and piped to underside of generator compartment with flexible hose and plug The drain shall be located where easil
91. he assembly design shall allow the body and subframe to act as one 1 component separate from the chassis As the chassis frame twists under driving conditions the spring mounting system shall eliminate any stress from being transferred into the body The spring loaded body mounts shall also prevent frame side rail or body damage caused by unevenly distributed stress and strains due to load and chassis movement Body mountings that do not allow relief from chassis movement will not be acceptable 17 REAR STEP BUMPER The full width rear bumper shall be constructed from 2 x 2 x 1 4 aluminum tubing frame and covered with 3 16 aluminum tread plate Any stepping surface shall have a grip surface material to meet NFPA requirements The bumper shall extend from the rear vertical body panel 17 and provide a rear step with a 1 space at body for water drainage REAR TOW EYES There shall be two 2 heavy duty rear mounted tow eyes securely attached to the body subframe below the apparatus body The tow eyes shall be fabricated from steel plate and shall have a black powder coat finish WHEEL WELL EXTERIOR PANEL The exterior panel of the body wheel well enclosure shall be constructed from 1 8 aluminum smooth plate DIEFORMED BEADED EDGE BODY FENDERS A die formed beaded edge shall be provided along the radius of the wheel well opening for a finished appearance WHEEL WELL LINERS The wheel wells shall be constructed by the compartment walls that
92. headliner height shall be 79 00 The cab front skin and floor shall be 190 thick aluminum The inside width shall be 90 00 and the front floor to the headliner height above the driver and officer shall be 82 00 All glass used in the cab shall be automotive tint The windshield shall have a maximum of 2890 sq in area and be of the wraparound design 52 88 wide and 27 88 high for maximum visibility Left and right windshield shall use the same interchangeable glass A molded rubber 11 grab handle shall be provided on the hinge post inside the cab at both the driver and officer door for entering and exiting the cab The driver and officer seats shall have an 8 25 high x 12 69 wide x 15 13 deep compartment in the seat box beneath them The compartment shall have a hinged door with an opening of 6 00 high x 12 50 wide Intermittent electric wipers with a single motor and electric powered wet arm type windshield washers shall be provided Access to the wiper motor shall be through the driver s side headlamp module located on the front cab fascia SVI 603 03 27 07 Page 7 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CAB DOORS The cab doors shall be flush full length type with hidden 375 stainless steel door hinges All doors shall be equipped with exterior pull handles suitable for use with firefighter mittens and keyed alike locks that are designed to prevent accidental lockout The interior latch
93. here shall be two 2 switches to control the above scene lights one 1 for streetside light s and one 1 for curbside light s The switches shall be located per the itemized compartment list REAR UPPER RECESSED FLOODLIGHTS One 1 Fire Research Focus 1500 watt 240 volt quartz floodlight s shall be installed in a recess style housing in the rear upper portion of the body Each light shall be wired directly to the electrical generator system with Carflex conduit and stranded copper wire The floodlights shall be protected with circuit breakers rated at the proper amperage and wire size Make Fire Research Model Focus P N FC200 M15 There shall be one 1 switch to control the above scene lights The switch shall be located per the itemized compartment list SVI 603 03 27 07 Page 77 of 86 Maui Police Department SVI Trucks Production Specification CO 3 COMMAND AREA TECH EQUIPMENT The following equipment shall be included to enhance Command and Communications operations DC power for the command area to be hot with the chassis master in the off position Power to come from additional batteries Two 2 Bosch 2mm wide angle cameras shall be supplied and mounted one 1 each side driver and passenger to provide 360 degree surveillance around apparatus Cameras shall be IP accessible COMMAND CAMERA SYSTEM There shall be one 1 Pelco ES31C22 5N camera system s complete with pan amp tilt drive system enclosure with shiel
94. hesive aluminum stick pins and retention caps All exposed insulation seams and edges are sealed to reduce moisture ontamination and debris build up MOBILE DATA TERMINAL PROVISION ABS DASH A Mobile Data Terminal MDT provision shall be provided above the glove box on the officer side of the dash The MDT provision shall be recessed 3 00 below the surface of the dash and 9 50 D x 13 75 W The glove box shall be 5 75 H x 12 75 W x 5 75 D with a hinged locking door A 20 amp 12AWG clean power and ground circuit will be provided to the MDT area CENTER CONSOLE A center console shall be provided between driver and offiver with cup holders map pockets and 12v power ports PAINT INTERIOR The interior metal surfaces shall be painted with a Zolatone 20 72 silver gray texture finish INTERIOR TRIM COLOR AND FLOOR MAT GRAY GRAY BLACK The cab interior soft vinyl trim surfaces shall be gray in color The cab interior vacuum formed ABS composite trim surfaces shall be gray in color The cab interior floormat shall be black in color The interior cab floor engine tunnel sides and front seat risers shall be covered with a mutlit layer mat consisting of 25 thick sound absorbing closed cell foam a heavy weight sound barrier a 06 thick non slip vinyl wear surface with a pebble grain finish and held in place by a pressure sensitive adhesive and aluminum cornering trim All exposed seams are sealed to reduce moisture contamination and debris build up
95. hing Technology Results in a lighter weight and compact design for ease of installation Actual product weight 32 lbs Functions of the PROsine 3 0 Inverter Charger Inverter Function When the PROsine 3 0 Inverter Charger is in inverter mode it draws power from a battery and delivers a true sine wave AC output that is the same as or better than the waveform supplied by your local electric utility In some cases the PROsine 3 0 Inverter Charger can deliver an even more stable waveform than your utility supplied power due to the extensive control circuitry incorporated in the design of the unit Charger Function The smart charging capability of the PROsine 3 0 Inverter Charger provides a multi stage charge to quickly bring back deep cycle batteries to their full charge Using microprocessor control the PROsine 3 0 Inverter Charger precisely regulates the voltage and current delivered to the battery accurately charging the battery without risk of overcharging and battery damage Depleted batteries are taken through the recommended Bulk Absorption and Float stages and a manually set Equalize stage is available to bring flooded batteries up to their peak capacity The charging algorithm used in the PROsine 3 0 Inverter Charger is based on the same charge cycle algorithm used in our proven TRUECHARGE battery charger line Automatic Transfer Switch An integral 30 amp rated relay has two functions When utility AC power fails or is dis
96. ice Department SVI Trucks Production Specification CO 3 OUTLETS AND CIRCUITS The generator shall supply the electrical equipment and outlets outlined below Proper circuit protection shall be installed as noted Two 2 120 volt exterior outlets one 1 each side near rear wheel well area The outlet s will be 120 volt 15 amp straight blade style NEMA 5 15R Outlet s shall be protected by a 15 amp circuit breaker Two 2 120 volt exterior outlets one 1 each side rear of body The outlet s will be 120 volt 15 amp straight blade style NEMA 5 15R Outlet s shall be protected by a 15 amp circuit breaker There shall be sixteen 16 120 volt straight blade outlet s located in the walk in area of the body The outlet s will be 120 volt 15 amp straight blade style NEMA 5 15R Outlet s shall be protected by a 15 amp circuit breaker One 1 at cab map box area for portable chargers One 1 cab rear wall at printer fax area Two 2 front face of curbside bench seat in conference area Two 2 front face of streetside bench seat in conference area One 1 under cab dispatch L desk Two 2 under OPS streetside slide out desk One 1 at streetside data rack One 1 under OPS curbside slide out desk One 1 at curbside data rack One 1 under OPS center table One 1 at conference area table angled console Any other positions required for specified monitors amp equipment OUTLET STRIP There shall
97. ice and shall be provided with a 5 year free replacement warranty SVI 603 03 27 07 Page 47 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CURBSIDE COMPARTMENT REAR C3 There shall be one 1 12V outlet s provided in the front face of the component console The interior useable compartment space shall be approximately 70 0 wide The approximate compartment door opening shall be 63 0 wide This compartment shall have a horizontally hinged box pan style door fabricated of 1 8 thick smooth aluminum The inner liner of the door shall be 3 16 thick smooth aluminum with an unpainted finish The door exterior shall be painted job color The hinged door s shall have a stainless steel 6 Hansen offset bent D ring locking handle A gasket shall be placed between stainless steel handle and door Door latches shall be a two point top and bottom rotary slam double catch latch recessed inside the double panel door with striker plate The hinged door s shall have a pair of tailgate style mechanisms to stop the door at 90 degrees Each door shall be capable of being closed without unlatching This compartment shall have the following items The removable access stairway for the command area shall be stored in this compartment There shall be one 1 OnScene Solutions LED light stick mounted vertically inside this compartment Each light stick shall include a 36 section above the subframe and an 18 section below
98. id This warranty should clearly describe the terms under which the vehicle s Manufacturer accepts responsibility for the cost to repair defects caused by faulty design quality of work or material and for the applicable period of time after delivery Cost of repairs refers to all costs related thereto including but not limited to the cost of materials the cost of labor The Manufacturer shall warrant all materials and accessories used in the vehicle s whether fabricated by the Manufacturer or purchased from an outside source and will deal directly with the Maui Police Department on all warranty work The warranty shall commence upon acceptance of the vehicle GENERAL WARRANTY ONE 1 YEAR The entire vehicle apparatus and equipment shall be warranted including parts and labor for a period of at least one 1 year commencing upon the placing of the unit in service by the Maui Police Department except that warranty on the tires and tubes batteries electrical lamps and other devices subject to deterioration is limited to the warranty of the manufacturer thereof and adjustments for same are to be made directly with the manufacturer Extended warranties on the engine transmission or other major components shall be detailed by Bidder in proposal This warranty shall not apply to those items which are usually considered normal maintenance and repair including but not limited to normal lubrication or proper adjustment of main functional op
99. iency Selectable color buttons and screen backgrounds All wiring to be appropriate gauge cross link with 311 degree F insulation All wires in the chassis shall be circuit numbered and function coded in addition the SAE wiring will be color coded The wiring shall be protected by 275 degree F minimum high temperature flame retardant loom as required The starting system shall be supplied with the following One 1 Cole Hersee 2484 master battery switch One 1 Cole Hersee EX26654A ignition switch One 1 starter button One 1 green LED indicator for battery on One 1 green LED indicator for ignition on aoa oa Includes 4 rocker switches on driver s dash 1 Secondary Braking On Off switch 2 Secondary Braking Variance Control High Low or High Med Low 3 Spare if not replaced by customer requested options 4 Spare if not replaced by customer requested options SVI 603 03 27 07 Page 21 of 86 Maui Police Department SVI Trucks Production Specification CO 3 Features included with the Multiplex system include Back up Alarm Disable Switch A back up alarm disable switch shall be installed in the cab dash within reach of the driver The switch will allow the driver to turn the back up alarm off The back up alarm shall automatically reset to sound the next time the transmission is placed in reverse Incandescent Ground Lighting Below Each Door The cab shall be equipped with Trucklite model 40003 seale
100. ill be a mixture of custom bent zinc coated steel fittings and Aeroquip flexible hose with E Z clip fittings All heater system hoses including auxiliary units shall be silicone with stainless steel constant torque clamps approved for use with silicone hose DELUXE INSULATION PACKAGE Additional insulation in the cab shall be installed to improve air conditioning and or heating in extreme weather climates as well as reducing road noise The sides roof and rear wall of the cab shall contain 1 thick multilayered insulation CAB TILT ACTUATION The entire cab shall tilt 45 degrees to allow for easy maintenance of the engine and transmission The cab tilt actuation shall be with an electric over hydraulic lift pump with a control box on a pendant for safe visual operation The lift system shall have an ignition interlock and red lock down indicator lamp which shall illuminate when holding down switch to indicate safe road operation It shall be necessary to activate the master battery switch with the park brake set in order to tilt the cab Two cab tilt cylinders shall be provided with velocity fuses in each cylinder port The cab pivots shall be 1 90 ball and be anchored to frame brackets with 1 25 diameter studs Two spring loaded hydraulic hold down hooks outboard of the frame shall be installed for holding the cab securely to the frame A steel safety assembly shall be installed on the right side cab lift cylinder to prevent accidental
101. in open and closed positions The doors shall be located as follows One in the opening between the cab area and the operations area this door shall be capable of being locked One in the opening between the operations area and the conference room capable of being locked from conference area Each pocket door shall be provided with a audible seal at top to reduce sound as mush as possible SVI 603 03 27 07 Page 52 of 86 Maui Police Department SVI Trucks Production Specification CO 3 SIDE ENTRY DOOR Access to the interior body compartment shall be provided through a side entry door The door opening shall be approximately 31 wide x 72 high Construction of the side entry door shall be with 1 8 aluminum exterior smooth plate the interior door pan being constructed from 1 8 aluminum tread plate The door shall be hung on full height 14 gauge stainless steel hinge with a 1 4 stainless steel pin The hinge shall be bolted to the door and body with stainless steel machine screws at offset 5 centers The hinge shall be slotted horizontally and vertically for ease of adjustment A polyester barrier film gasket shall be placed between the stainless steel hinge and door The latch mechanism shall include a paddle handle on inside and a locking Hansen offset bent D ring handle on exterior A polyester barrier film gasket shall be placed between the stainless steel handles and the aluminum door panels The door latch shall be a double
102. in the cab within reach of the Driver and or Officer SVI 603 03 27 07 Page 76 of 86 Maui Police Department SVI Trucks Production Specification CO 3 SIDE UPPER RECESSED FLOODLIGHTS STREETSIDE One 1 Fire Research Focus 500 watt 120 volt quartz floodlight s shall be installed in a recess style housing in the side upper portion of the cab Light shall be located on Spartan cab rearward corner below specified warning light Each light shall be wired directly to the electrical generator system with Carflex conduit and stranded copper wire The floodlights shall be protected with circuit breakers rated at the proper amperage and wire size Make Fire Research Model Focus P N FC200 S50 There shall be two 2 switches to control the above scene lights one 1 for streetside light s and one 1 for curbside light s The switches shall be located per the itemized compartment list SIDE UPPER RECESSED FLOODLIGHTS CURBSIDE One 1 Fire Research Focus 500 watt 120 volt quartz floodlight s shall be installed in a recess style housing in the side upper portion of the cab Light shall be located on Spartan cab rearward corner below specified warning light Each light shall be wired directly to the electrical generator system with Carflex conduit and stranded copper wire The floodlights shall be protected with circuit breakers rated at the proper amperage and wire size Make Fire Research Model Focus P N FC200 S50 T
103. ing all miscellaneous coax cable 120 volt AC wiring and cable connections The system shall be designed to allow the Fire Department to elevate the surveillance camera to any height up to approximately 25 above the apparatus body The camera shall supply a picture to each of the specified TV monitors Each TV monitor shall be an individual set capable of tuning to the surveillance camera or video recorder DVD RECORDER A Bosch Dibos DVD recorder shall be provided and installed in designated data rack The DVD recorder shall be wired to outputs from Pelco camera on mast to all Samsung monitors specified CONFERENCE MONITOR AND SMART BOARD A 40 LCD flat screen monitor shall be provided located at rear conference area wall Monitor shall be able to display surveillance camera video video recorder computer monitor or the local television stations 40 screen shall be provided with Smart Board overlay marker board Marker board uses computer interface to save marker board notes and video image together in digital format A 20 touch screen shall be provided adjacent to 40 screen for video control and viewing A Dell desktop personel comupter or equal shall be included with monitor smart board system with a video capture card SVI 603 03 27 07 Page 81 of 86 Maui Police Department SVI Trucks Production Specification CO 3 COMMAND CAMERA SYSTEM There shall be one 1 Pelco ES31C22 5N camera system s complete with pan amp tilt d
104. inish painted surfaces Touch up paint shall be provided with completed apparatus PAINT FINISH The apparatus body shall be painted single color with Akzo Nobel Inc Sikkens Autocryl Acrylic Urethane Finish paint for a high gloss hard finish Color White Paint Number The painted body shall be finished with a clear coat of acrylic urethane for paint protection and maximum quality finish PAINT WARRANTY The apparatus shall be provided with a seven 7 year warranty to the original Owner Warranty is provided by Sikkens sponsored by AKZO Nobel A Sikkens Warranty sheet with all conditions shall be provided with the delivered apparatus BODY UNDERCOATING The entire underside of apparatus body shall be sprayed with black automotive undercoating Undercoating shall cover all areas to retard corrosion under the apparatus UNDERCOAT WARRANTY The undercoating shall be provided with a warranty by its manufacturer for the lifetime of the vehicle The re spray warranty shall be transferable between vehicle owners Should the coating applied to the underside of the body and wheel wells of the vehicle ever flake off peel chip or crack due to drying out the damaged area shall be re sprayed without charge to the vehicle owner SVI 603 03 27 07 Page 39 of 86 Maui Police Department SVI Trucks Production Specification CO 3 REFLECTIVE STRIPE A 6 reflective stripe shall be affixed to the perimeter of the vehicle per NFPA 19
105. itary double wrapped front eye Both spring eyes shall have a case hardened threaded bushing installed with lubrication counterbore and lubrication land off crossbore with grease fitting The spring capacity shall meet or exceed the capacity of the front axle The hydraulic power assist steering gear shall be a TRW TAS 85 A Vickers hydraulic power steering pump shall be gear driven from the engine The steering ratio shall be 23 3 1 and have 6 2 turns stop to stop FRONT TIRES The front tires shall be Michelin 315 80R 22 5 20PR L tubeless radial XZA1 highway tread with 22 5 x 9 0 ten 10 stud disc wheels The tires and wheels shall be rated at 18 000 pounds FRONT AXLE CRAMP ANGLE The hub piloted MFS 18 model front axle cramp angle shall be a minimum of 50 degrees when using the 315 80R 22 5 front tires FRONT WHEELS ALCOA ALUMINUM The front wheels shall be Alcoa hub piloted 9 00 x 22 5 polished aluminum wheels FRONT WHEEL BEARINGS OIL LUBRICATED The front axle wheel bearings shall be oil lubricated and come equipped with an oil level visual inspection window FRONT SHOCK ABSORBERS Two 2 Bilstein monotubular design nitrogen gas charged shock absorbers shall be part of the front axle suspension Bilstein shall warranty the shock for a period of five 5 years DISC BRAKES The front axle shall have ArvinMeritor Rockwell ADB 1560 disc type brakes with 15 vented rotors providing a total of 120 sq in of braking area and auto
106. l be cut out to match the cab opening Additional reinforcements with metal angle or tubing shall be provided to back of cab or front of body if necessary so that the walk through opening weakens neither the cab nor body integrity The connection shall be weather resistant yet provide the cab and body to move independent of each other A flexible 3 rubber weather strip shall be attached to a stainless steel sheet metal frame around the perimeter of the opening in the back wall of the cab A drip rail shall be provided on front of body above the opening to channel water to both sides of opening Stainless steel scuff panels shall be provided on back of cab were the rubber seal on body comes in contact with cab A formed metal frame shall be bolted to the front of the body The body mounted frame W be provided where the rubber seal comes into contact with the body The framework shall be painted to match the body color The base of the opening shall be covered with a 3 16 aluminum tread plate full width panel which will overlap from the cab to body so that the rubber seal can not be damaged Full width padded foam cushion head bumpers shall be provided on both sides of opening Head bumpers shall be covered with matching interior vinyl and bolted to each side of walk through CUT OUT IN REAR CAB WALL The rear wall of the custom cab shall be cut out 24 wide for walk thru application The height of the cutout shall be determined by the cab struc
107. lectrical knockout panel installed in base and removable rear electrical knockouts with BNC knockouts for UHF VHF antennas installed in top A 1 4 20 threaded grounding and bonding stud shall be installed in base of enclosure Rack shall be warranted to be free from defects in material or workmanship under normal use and conditions for the lifetime of the product In addition the WR shall be provided with model WRFD 37 reinforced 16 gauge solid steel front door Integrated fan tops with proportional speed thermostatic fan control and Vertical outlet strip model PD 2415SC NS A minimum 37 amp UPS uninterruptable power supplies with surge protection shall be located in data rack An exterior body hinged door shall be provided allowing access to rear of data rack Door shall be capable of swinging past 90 degree and be provided with keyed lock Data Rack shall be provided by customer Ordered through Harmer Communication SVI 603 03 27 07 Page 60 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CURBSIDE INTERIOR AREA IC4 The specified TV and Smart Board shall be located on rear wall of the slide out above base cabinet CONFERENCE TABLE The interior of the apparatus shall be provided with two 2 conference tables location and sizes below The desktop surface shall be fabricated of 3 16 smooth aluminum and the structure shall be 2 x 2 aluminum tubing powdercoated to match the interior The tables shall be rei
108. ll be 3 16 thick smooth aluminum with an unpainted finish The door exterior shall be painted job color The hinged door s shall have a stainless steel 6 Hansen offset bent D ring locking handle A gasket shall be placed between stainless steel handle and door Door latches shall be a two point top and bottom rotary slam double catch latch recessed inside the double panel door with striker plate The hinged door s shall have a pneumatic cylinder to hold door in the open and closed positions Each door shall be capable of being closed without unlatching Door checks shall be bolted to the upper compartment door header and the box pan of the door This compartment shall have the following items The diesel engine driven generator There shall be one 1 OnScene Solutions LED light stick mounted vertically inside this compartment Each light stick shall include a 36 section above the subframe and an 18 section below the subframe There shall be 30 LEDs per 18 light and 60 LEDs per 36 light The light stick shall be rated at 100 000 hours of service and shall be provided with a 5 year free replacement warranty SVI 603 03 27 07 Page 45 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CURBSIDE COMPARTMENT FRONT C1 The interior useable compartment width shall be approximately 46 0 wide The approximate compartment door opening shall be 39 0 wide This compartment shall have a horizontally hinged
109. load The rear air suspension shall have a maximum rated capacity of 24 000 pounds GAWR SINGLE REAR AXLE AIR BRAKE SYSTEM A FMVSS 121 and NFPA rapid build up compliant air brake system shall be provided It shall include three 3 air reservoirs with a total of 4136 cubic inch of air capacity A Bendix E6 floor mounted tread valve shall be mounted in the cab for service brake control A Bendix PP1 control valve shall operate the parking brake system Emergency braking shall be controlled through the Bendix treadle valve and modulated through a Meritor Wabco inversion valve The rear axle spring brakes are to automatically apply in case of air pressure loss below 60 psi with a mechanical means for releasing the spring brake chambers BRAKE DUST SHIELDS The single rear axle shall be equipped with brake dust shields ALCOA DURABRIGHT COATING The Alcoa aluminum wheel will have the Alcoa Durabright wheel treatment as an integral part of the wheel AXLE COVER KIT STAINLESS STEEL ALL WHEELS The front and rear wheels shall have stainless steel lug nut covers The front axles shall be covered with stainless steel baby moons with hole to view oil seal window The rear axles shall be covered with foam mounted stainless steel high hats The lug nut covers baby moons and high hats shall be American made Real Wheels brand mirror finish 304L grade non corrosive stainless steel meeting D O T certification standards All stainless steel baby mo
110. lticoupler with the antenna mounted inverted on the camera mast below the camera Two 2 Daniels Electronics VHF repeaters combined into one transmit antenna mounted on vehicle roof receivers combined through a multicoupler with the antenna mounted inverted on the camera mast below the camera Six 6 Maui Police Department supplied EF Johnson 5300 Ascend Series 700 800MHz mobile radios with Multi Net II P25 Trunking P25 Conventional SmartNet SmartZone protocols installed mounted in a 19 rack in the vehicle cab adjacent to the Dispatcher position accessible for channel selection with antennas mounted on the vehicle cab roof Two 2 Motorola CDM 1550 LS UHF mobile radios with Conventional LTR SmartNet SmartZone protocols installed mounted in a 19 rack in the vehicle cab adjacent to the Dispatcher position accessible for channel selection with antennas mounted on the vehicle cab roof Four 4 Motorola CDM 1550 LS VHF mobile radios with Conventional Passport DigitalAstro SmartNet SmartZone protocols installed mounted in a 19 rack in the vehicle cab adjacent to the Dispatcher position accessible for channel selection with antennas mounted on the vehicle cab roof Two 2 ICOM IC A200M VHF AM radios mounted in a 19 rack in the vehicle cab adjacent to the Dispatcher position accessible for channel selection with antennas mounted on the vehicle cab roof Two 2 Nextel mobile cellular phone with base kit will be inst
111. material the Aeron chair distributes weight evenly over the seat and back conforming to each person s shape The material also lets air pass through adding to long term comfort by preventing body heat build up The armrests shall be independently adjustable with settings that pivot inward 17 5 degrees for keying and outward 15 degrees Arm height adjusts independently within a four inch vertical range The stock Herman Miller caster wheel assembly shall be removed and the base of the stock pedestal shall be affixed to the glider mechanism recessed in the slide out floor The base of the chair pedestal shall be attached to a custom manufactured glider base that will allow up to 7 inches of fore and aft positioning The glider base shall not require a mechanical lock or release devices to slide SVI 603 03 27 07 Page 56 of 86 Maui Police Department SVI Trucks Production Specification CO 3 STREETSIDE INTERIOR AREA IS3 DATA RACK A Middle Atlantic Products roll out and rotating model WR 37 32 with 37 rackspaces shall be provided directly behind wall between central communications and rear conference area on streetside Overall dimensions of rack shall be 76 6 H x 24 W x 32 8 D Useable height shall be 64 7 rackspaces useable depth shall be 26 Rack shall be fully welded construction and provide a 750 lb weight capacity with proper distribution Rack shall be constructed of steel and finished in a durable black powder
112. matic slack adjusters CHASSIS ALIGNMENT The chassis frame rails shall be cross checked for length and squareness Front and rear axles shall be laser aligned Tires and wheels shall be aligned and toe in set on the front tires at the chassis manufacturer s facility The completed apparatus should be rechecked for proper alignment after the chassis has been fully loaded SVI 603 03 27 07 Page 13 of 86 Maui Police Department SVI Trucks Production Specification CO 3 STEERING COLUMN AND WHEEL The Douglas Autotech steering column shall be a seven 7 position tilt and 2 25 telescopic type with an 18 steering wheel The steering wheel shall be covered with black absorbite padding The steering column shall contain a horn button self canceling turn signal switch four way hazard switch and headlamp dimmer switch FRONT MUD FLAPS The front wheel wells shall have mud flaps installed on them REAR AXLE The rear axle shall be an ArvinMeritor model RS 24 160 with single reduction gearing and shall have a rated capacity of 24 000 pounds GAWR TOP SPEED The top speed of the vehicle shall be approximately 65 MPH 2 MPH at governed engine RPM REAR BRAKES The rear brakes shall be ArvinMeritor 16 5 x 7 S cam type with ArvinMeritor automatic slack adjusters ABS BRAKE SYSTEM A Meritor Wabco four sensor four modulator anti lock braking system shall be installed on the front and rear ArvinMeritor axles for safer vehicle control during
113. med ABS composite driver officer and a two 2 piece center HVAC cover Mounted to the trim panels shall be two 2 5 75 x 22 50 vinyl sunvisors ABS INNER DOOR PANELS The inner door panels shall be a vacuum formed ABS composite panel with robust styling grooves that provide structural integrity A partial aluminum reinforcement structure shall be included The door panels shall also include multiple recesses to accept optional features such as Custom Built For logos and metal kickplates inserts A Fireman Friendly cast aluminum pull handle shall be included with the front door panel SVI 603 03 27 07 Page 26 of 86 Maui Police Department SVI Trucks Production Specification CO 3 ENGINE COVER The fixed type engine cover shall be a maximum of 21 00 high x 36 00 wide The cover shall be an integral part of the cab and made of 0 19 thick aluminum The interior cab side shall be covered with a multi layer mat consisting of 25 thick sound absorbing closed cell foam a heavy weight sound barrier a 06 thick non slip vinyl wear surface with a pebble grain finish and held in place by a pressure sensitive adhesive and aluminum cornering trim All exposed seams are sealed to reduce moisture contamination and debris build up The engine side of the cover shall be heavily insulated with multi layer insulating materials consisting of foam a 1 0 Ibs per sq ft sound barrier with a facing that resists heat transfer and held in place by ad
114. mpere 4PDT power relay shall be installed Relay shall cut off the connection between the generator supply circuit and device circuits when shore power is connected One 1 wired to specified inverter One 1 wired to outlets at each interior desk position SHORE POWER PLUG Two 2 Kussmaul 30 amp Super Auto Eject shore power plug s shall be furnished and installed The shore power connection shall automatically disengage from vehicle when chassis ignition is engaged The Auto eject outlet cover shall be yellow The shorepower plug receptacle shall be located above the generator compartment door SHORE POWER RECEPTACLE A 100 ampere 240 volt single phase shore power receptacle shall be provided on the apparatus to provide an external power source for apparatus electrical circuits A matching 100 ampere plug shall be shipped with the apparatus for Fire Department supplied external power source wiring Shore power shall be wired to apparatus main circuit breaker in the circuit breaker distribution panel and feed all 120 240 electrical circuits on apparatus To protect both the generator and external power source from backfeed a manual three way 100 ampere rotary switch shall be installed at the generator control panel to cut off the connection between the apparatus circuits and the generator when the external power source plug is in use Switch shall be labeled SHORE OFF GENERATOR SVI 603 03 27 07 Page 71 of 86 Maui Pol
115. n exterior compartment One 1 modular Panasonic KX TA824 electric switching system The base system has three 3 Central Office C O lines and eight 8 extensions This system is expandable to eight 8 C O lines and twenty four 24 extensions One 1 Panasonic KX TA82491 Direct Inward System Access DISA FAX detection card Note If a FAX call is received and a CNG tone is detected during the outgoing message the call will be automatically routed to the designated FAX extension eliminating the need for a dedicated land line and cell line The card will also allow personnel to call IN and to dial an extension directly One 1 Panasonic KX T7730B programing telephone with intercom and P A features Eleven 11 Panasonic KX T7750B telephones with intercom and P A features Three 3 Telular Phonecell SX5T GSM digitally interfaced to the phone system One 1 VOIP router 2 line for use with local Roadrunner system Four 4 RJ 11 phone jacks in external patch compartment In the event that no cellular service is available and wireless connections are available the phone system is to include an interface for landline connection to the Verizon system The phone system shall interface with the PA system All telephone lines and cellular antenna cables shall be installed in ENT conduit MPD SUPPLIED CATV MODEM One 1 MPD supplied cable modem and an eight 8 outlet distribution amplifier shall be mounted in streetside ca
116. nd muffler System joints shall be connected with lapping band clamps COOLING SYSTEM The cooling system shall have sufficient capacity to keep the engine properly cooled under all conditions of road and pumping operations The cooling system shall be designed and tested to meet or exceed the engine and transmission manufacturer and EPA requirements The complete cooling system shall be mounted in a manner to isolate the system from vibration and stress The individual cores shall be mounted in a manner to allow expansion and contraction at various rates without inducing stress into the adjoining core s Radiator The radiator shall be a cross flow design constructed completely of aluminum with welded side tanks The radiator shall have a minimum of a 571 sq in core and be bolted to the bottom of the charge air cooler to allow a single depth core thus allowing a more efficient and serviceable cooling system The radiator shall also be equipped with a drain cock to drain the coolant for serviceability Surge Tank The cooling system shall be equipped with a surge tank that is capable of being filled and removing entrained air from the system The surge tank shall be equipped with a low coolant probe and sight glass to monitor the level of the coolant The surge tank shall have a cap that meets the engine manufactures pressure requirements as well as the system design requirements Coolant The cooling package shall have Extended Life Coolant
117. ne of the above shall be interpreted to mean that the use of used or rebuilt products is allowed under this document The term Heavy Duty as used to describe an item shall mean in excess of the standard quantity quality or capacity and represents the best most durable strongest etc part component Maui Police Departmentsystem etc that is available The Maui Police Department or their designate shall be the sole judge of quality construction and stability of the apparatus and equipment being offered Welding shall not be employed in the assembly of the apparatus in a manner that will prevent the ready removal of any component part for service or repair All steel and stainless steel welding shall be done to American Welding Society D1 1 83 recommendations for structural steel welding All aluminum welding shall be done to American Welding Society and ANSI D1 2 83 requirements for structural welding of aluminum Defective components shall not be furnished Parts equipment and assemblies which have been repaired or modified to overcome deficiencies shall not be furnished without the approval of the Maui Police Department Welded bolted and riveted construction utilized shall be in accordance with the highest standards of the industry Component parts and units shall be manufactured to definite standard dimensions with proper fits clearances and uniformity General appearance of the vehicle shall not show any evidence of poor quality of
118. nforced with aluminum tubing to support personnel sitting on edge of the desk The corners of the desk top shall be radiused There shall be a 3 diameter hole in the center of each conference table to allow access to below desk power and network connections The location and size of the conference tables will be One 1 in the front command area approximately 44 x 48 front to back with a recessed map storage area and hinged cover One 1 in the rear conference area approximately 36 x 30 front to back flip down style located on rear wall below LCD SmartBoard display INTERIOR BENCH SEAT The interior rear curbside corner of body shall be provided with a bench seat located above the exterior Compartment C3 Seat will be approximately 150 wide extending full width of Conference Area The seat shall be fabricated of 3 4 exterior grade plywood with 3 thick foam and heavy duty vinyl covering The seat backrest shall be approximately 12 high x 2 thick and constructed the same as the seat REMOVABLE FLIP UP DESK six 6 removable flip up desks shall be provided three at each bench seat Each desk to have a writing surface approximately 18 x 12 mounted on a post that fits into a reciever located on front face of bench seat riser Each desk shall fold flat and be able to be stored under bench seat AM FM RADIO An AM FM radio shall be located in streetside slide out with recessed cieling mounted speakers SVI 603 03 27 07 P
119. nimum Exceptions will not be accepted or permitted since all raw materials of the specified type are available to all Manufacturers Since all custom Manufacturers have the ability to shear break and weld as these specifications require all basic design requirements shall be complied with Subletting any part of the fabrication painting or finishing of the apparatus will not be acceptable SVI 603 03 27 07 Page 1 of 86 Maui Police Department SVI Trucks Production Specification CO 3 ACCESSIBILITY Parts and components shall be located or positioned for rapid and simple inspection and recognition of excessive wear or potential failure Whenever functional layout of operating components determines that physical or visual interference between items cannot be avoided the item predicted to require the most maintenance shall be located for best accessibility Cover plates which must be removed for component adjustment or part removal should be equipped with quick disconnect fasteners or hinged panels Drains filler plugs grease fittings hydraulic lines bleeders and check points for all components should be located so that they are readily accessible and do not require special tools for proper servicing Design practices should minimize the number of tools required for maintenance NAMEPLATES AND INSTRUCTION PLATES All nameplates and instruction plates shall be metal or plastic with the information engraved stamped or etched thereon
120. nimum level of quality and design All Bidders shall be required to meet these minimum requirements It is the intent of these specifications to fully describe the requirements for a custom built emergency type vehicle In order to extend the expected service life of this vehicle the body module shall be removable from the chassis frame and be capable of being installed on a new chassis The sheet metal material requirements including alloy and material thickness throughout the specifications are considered to be a minimum Since such materials are available to all Manufacturers the material specifications shall be strictly adhered to The fabrication of the body shall be formed sheet metal Formed components shall allow the Maui Police Department to have the body repaired locally in the case where any object has struck the body and caused damage The use of proprietary extrusions will prevent the Maui Police Department from such repair and shall NOT be used Following construction of the subframe which will support the apparatus body the sheet metal portion of the body shall be built directly on the subframe The joining of the subframe and body shall be of a welded integral construction The sheet metal fabrication of the body shall be performed using inert gas continuous feed welders only The entire body shall be welded construction The use of pop rivets in any portion of structural construction may allow premature failure of the body struct
121. nt top and bottom rotary slam double catch latch recessed inside the double panel door with striker plate The hinged door s shall have a pair of tailgate style mechanisms to stop the door at 90 degrees Each door shall be capable of being closed without unlatching This compartment shall have the following items The 100amp 240 volt electrical shore line connection Specified 12 120 volt inverter The additional batteries specified shall be located in this compartment on 400 Ib rated slide out tray The specified Fleet Power 2500 12 inverter charger shall be located near the battery location A hinged hatch shall be provided in compartment floor for access to 100amp shore line connection There shall be one 1 OnScene Solutions 18 LED light stick installed in this compartment Each light shall be mounted horizontally inside the compartment door There shall be 30 LEDs per 18 light The light stick shall be rated at 100 000 hours of service Each light stick shall be provided with a 5 year free replacement warranty SVI 603 03 27 07 Page 44 of 86 Maui Police Department SVI Trucks Production Specification CO 3 STREETSIDE COMPARTMENT REAR S3 The interior useable compartment space shall be approximately 70 0 wide The approximate compartment door opening shall be 63 0 wide This compartment shall have vertically hinged box pan style doors fabricated of 1 8 thick smooth aluminum The inner liner of the door sha
122. o 1800 Router for DHCP and Inbound QOS with Integrated 8 Port Ether Switch Network Module Includes AES Chipset QOS amp Header Compression Tripp Lite SmartOnline Rack Tower Mounted Online UPS System 1000VA online Zero transfer time power conditioner and UPS Maintains 120V 2 output during overvoltages to 138V and brownouts as low as 65V Fault tolerant auto bypass NOTE Requires 6 RU of rack space equipment rack sold separately Equipment to be provided by customer SatCom Systems Inc SATELLITE TV SYSTEM A satellite TV antenna and reciver system shall be installed on vehicle Equipment to be provided by customer Harmer Communication VIDEO SOURCES One 1 Wingard Sensar IIl RV 3090 broadcast TV antenna w amplified multi switch shall be provided and wired to location determined at pre construction meeting SVI 603 03 27 07 Page 82 of 86 Maui Police Department SVI Trucks Production Specification CO 3 RADIO COMMUNICATIONS EQUIPMENT FOR TELEX DISPATCH SYSTEM The following Radio Communications equipment shall be provided and installed as directed by Maui Police Department Four 4 Daniels Electronics 800MHz repeaters combined into one transmit antenna mounted on vehicle roof receivers combined through a multicoupler with the antenna mounted inverted on the camera mast below the camera Two 2 Daniels Electronics UHF repeaters combined into one transmit antenna mounted on vehicle roof receivers combined through a mu
123. om the ground SVI 603 03 27 07 Page 11 of 86 Maui Police Department SVI Trucks Production Specification CO 3 FUEL TANK The fuel tank shall have a minimum capacity of sixty eight 68 gallons The baffled tank shall be made of 14 gauge phosphate coated steel with chromate epoxy exterior finish The fuel tank shall be mounted under the frame behind the rear axle on strap hangers with a U strap bolted front and rear so the tank can be easily dropped and removed Tank shall have vent port to facilitate rapid filling without blow back A roll over ball check vent shall be installed Dual draw tubes and dual sender ports shall be installed A 2 NPT fill ports shall be available for right or left hand fill A 1 2 NPT drain plug shall be centered in the bottom of the tank The standard fuel line for ISC and ISL engines will be nylon material rated for diesel fuel All other engines will be steel wire braid reinforced rubber FRONT BUMPER A one piece 10 gauge 304 polished stainless steel front bumper shall be provided The bumper shall be 101 and 12 high two 2 rio wrap around type The bumper shall be extended 6 ahead of the cab AIR HORNS Dual Grover Stuttertone 21 air horns shall be recessed in the front bumper one 1 each on the driver and officer inboard mounting positions A 3 8 airline teed equal distance from each horn shall be installed ADDITIONAL AIR RESERVOIR An additional 1200 cubic inch air reservoir sh
124. on the rear of the body one 1 each side in the upper corners Each light shall have a blue LEDs with clear lens and chrome finished flange The lights shall be switched at 12 volt control panel in cab UPPER LEVEL WARNING LIGHT OPTIONS 3M OPTICOM One 1 3M Opticom emitter light shall be installed either inside specified light bar or on cab roof The Opticom shall be activated with light bar and de activated when the park brake is set and the vehicle is in blocking mode SVI 603 03 27 07 Page 67 of 86 Maui Police Department SVI Trucks Production Specification CO 3 LOWER LEVEL WARNING LIGHTS ZONE A FRONT WARNING LIGHTS The front lower warning lights shall be supplied and installed by the cab chassis manufacturer They shall be Whelen lights to complete an NFPA compliant lower level warning light system The front lower warning lights shall be switched from 12 volt control panel ZONES B AND D SIDE WARNING LIGHTS There shall be four 4 Whelen model 600 6 x 4 LED lights provided two on each side located near the corners of the apparatus Each light shall have a blue LEDs with clear lens and a chrome finished flange The lights shall be switched at the 12 volt control panel in the cab Zones B amp D Sides Midship There shall be two 2 Whelen model 600 6 x 4 LED lights provided one 1 on each side located between the corners of the apparatus so that there is no more than 25 feet between side lower warning lights
125. ondary front brake line red the parking brake line orange and the auxiliary outlet will be blue Brass compression type fittings shall be used on the nylon tubing All drop hoses shall be fiber reinforced neoprene covered hoses AIR TANK MOUNTING The air tanks shall be installed one 1 inch inboard of the frame rails SVI 603 03 27 07 Page 16 of 86 Maui Police Department SVI Trucks Production Specification CO 3 ENGINE A Caterpillar C9 400HP turbocharged air charged cooled engine shall be provided TYPE In Line six 6 cylinder 4 cycle HORSEPOWER 400 2100 rpm Governed 2100 rpm TORQUE 1100 lbs ft 1400 rpm DISPLACEMENT 537 cu in GOVERNOR Electronic A wiring harness shall be provided with a drop out at the back of the cab The harness shall include a connector to allow an optional harness for the pump panel to be plugged into it Circuits shall be provided for multiplexed gauges tachometer oil pressure engine temperature hand throttle high idle and PSG system A circuit for J1939 data link shall also be provided at the drop out An engine mounted combination full flow by pass oil filter with replaceable spin on cartridge shall be part of the engine s lubrication system An external mounted transmission cooler shall be part of the engine cooling system A spin on engine coolant filter with shut off valve shall be provided AIR COMPRESSOR The air compressor on the engine shall be a Bendix BA 92
126. ons and high hats shall carry a lifetime warranty FRONT WHEEL SERVICE BRAKE LOCK UP SYSTEM A front wheel service brake lock up system shall be installed which will apply both the front air and rear spring brakes upon application of the PP 1 push pull valve in the cab SVI 603 03 27 07 Page 15 of 86 Maui Police Department SVI Trucks Production Specification CO 3 AIR DRYER A Meritor Wabco system saver 1200 spin on desiccant air dryer with a 12 volt 100 watt automatic heated moisture ejector shall be installed in the air brake system The air dryer incorporates an internal turbo cutoff valve that closes the path between the air compressor and air dryer purge valve during the compressor unload cycle The turbo cutoff valve allows purging of moisture and contaminants without the loss of turbo boost pressure The Meritor Wabco air dryer shall come with a three 3 year or 300 000 mile warranty provided by Meritor Wabco Vehicle Control Systems MANUAL DRAINS ON AIR TANKS Manual drains shall be installed on all reservoirs of the air brake system CABLE DRAIN VALVES ON AIR TANKS The manual drain valves shall have pull cables attached The actuation pull cable shall be extended out to the frame rail to allow the drains to be activated from the side of the chassis NYLON AIR LINE TUBING A dual air system plumbed with color coded reinforced nylon tubing air lines shall be installed The primary rear brake line shall be green the sec
127. ose Neck Map Light Body Interior Hazard Warning Light Cab Chassis Supplied Electronic Back up Alarm Cab Chassis Supplied Walk in Interior Lights 12 Volt Add to Insert Interior Lite Weldon Recessed 7 Clear Tail Lights Whelen 600 LED Halogen 4 Place Cast Alum Beze Midship LED Body Marker Turn Signal Clearance Lights and Reflectors LED std Step Door Ground Light NFPA Req d License Plate Light and Bracket Siren Cab Chassis Supplied Siren Speaker s Cab Chassis Supplied Side Scene Whelen 900 1 Ea Side Rear Scene Whelen 900 2 Rear Rear Scene Light Activation in Reverse Side Scene Whelen 508 2 Ea Side No Directional Light WARNING LIGHT SYSTEM Warning Light System Walk in NFPA Warning Light Package Upper Level Whelen Zone A Front Lightbar LED Whelen FN72QLED 72 Zones B amp D Sides LED 900 Series Whelen 9OROOFRR Blue SUR LED 900 Series Whelen 9OROOFRR Blue SUF Zone C Rear LED 900 Series Whelen 9OROOFRR Blue Upper Level Misc Options 3M Opticom Lower Level Whelen Zone A Front Cab Chassis Supplied Zones B amp D Sides LED 600 Series 2 Whelen 60ROOFRR Blue Zones B amp D Sides Midship LED 600 Series 1 Whelen 60ROOFRR Blue Mid Zone C Rear LED 600 Series Whelen 60ROOFRR Blue LINE VOLTAGE SYSTEM Line Voltage Sys
128. ositions 13 amp 14 SVI 603 03 27 07 Page 46 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CURBSIDE COMPARTMENT INTERMEDIATE C2 The interior useable compartment width shall be approximately 46 0 wide The approximate compartment door opening shall be 39 0 wide This compartment shall have a horizontally hinged box pan style door fabricated of 1 8 thick smooth aluminum The inner liner of the door shall be 3 16 thick smooth aluminum with an unpainted finish The door exterior shall be painted job color The hinged door s shall have a stainless steel 6 Hansen offset bent D ring locking handle A gasket shall be placed between stainless steel handle and door Door latches shall be a two point top and bottom rotary slam double catch latch recessed inside the double panel door with striker plate The hinged door s shall have a pair of tailgate style mechanisms to stop the door at 90 degrees Each door shall be capable of being closed without unlatching This compartment shall have the following items An air conditioning system compressor shall be located in this compartment There shall be one 1 OnScene Solutions LED light stick mounted vertically inside this compartment Each light stick shall include a 36 section above the subframe and an 18 section below the subframe There shall be 30 LEDs per 18 light and 60 LEDs per 36 light The light stick shall be rated at 100 000 hours of serv
129. p alarm shall actuate automatically when the transmission gear selector is placed in reverse WALK IN INTERIOR LIGHTS There shall be eight 8 Weldon recessed 7 diameter interior dome light s with clear lens provided with a switch at the entry door for body 12 volt interior lighting Two 2 located in cab dispatch area One 1 centered over operations area table One 1 over curbside body entry door One 1 centered between two data racks Three 3 located in conference area TAIL LIGHTS Rear body tail lights shall be vertically mounted per Federal Motor Vehicle Safety Standards The following lights shall be furnished Two 2 Whelen amber LED 600 Series 60A00TAR turn signal lights Two 2 Whelen red LED 600 Series G0ROOXRR stop tail lights Two 2 Whelen halogen 600 Series 60JOO0CR back up lights with clear lens Two 2 Whelen warning lights as detailed in the warning light section Two 2 Whelen CAST 4V 4 light polished aluminum bezels shall be provided one 1 each side vertically mounted on the rear of the apparatus body for the above tail lights MIDSHIP MARKER TURN SIGNAL Two 2 LED midship body turn signal lights shall be installed There shall be one 1 light on each side of the body in the wheel well ahead of the rear axle Both lights shall have an amber lens and operate with the chassis turn signals SVI 603 03 27 07 Page 64 of 86 Maui Police Department SVI Trucks Production Specification CO
130. provided One 1 pre heat switch if generator is diesel One 1 start stop switch One 1 generator running indicator light SVI 603 03 27 07 Page 74 of 86 Maui Police Department SVI Trucks Production Specification CO 3 INVERTER The apparatus shall be equipped with one 1 Xantrex model Prosine 3 0 Inverter that provides 120 VAC 60 cycle 3000 watt output from 12 VDC PROsine 3 0 Protection Features Over temperature shutdown Auto overload protection Battery reverse polarity fuse Short circuit protection Inverter output PROsine 3 0 Product Features True Sine Wave Output lt 5 THD A smooth step free waveform delivering dependable and reliable electrical power for even the most demanding and sensitive of loads Super Quick Transfer A maximum detect and transfer time of 20 milliseconds 16 ms typically ensures critical loads stay powered up when AC power drops away Multi Stage Charger Can be set for either gel or flooded batteries and delivers 120 amps of charging current for quick accurate battery charging 99 Charger Power Factor Rating Allows operation from smaller generators as the full 120 amps of charging current requires only 17 Amps of AC input power Full Range Operation Battery banks are often well below the ideal normal 12 Volts To compensate for that fact the PROsine 3 0 Inverter Charger delivers its rated 3000 Watts continuous right down to 10 5 Volts input High Frequency Switc
131. ratus and associated equipment as defined in NFPA 1002 Standard for Fire Apparatus Driver Operator Professional Qualifications and NFPA 1500 Standard on Fire Department Occupational Safety and Health Program Inc from CO CA port Ocean freight by HT amp T CAB AND CHASSIS The cab and chassis shall be a Spartan Chassis Inc Flat Floor Diamond model DA4AH extended long four door 24 raised roof over crew and driver officer area aluminum tilt cab built specifically for the fire service by a publicly held U S parent company specializing in chassis design for all fire service applications The cab and chassis shall meet the requirements of the National Fire Protection Association Standard 1901 2003 edition or latest edition FLAT FLOOR ELFD 24 RAISED ROOF TILT CAB The cab shall be a Spartan Chassis Inc Flat Floor ELFD extended long four door 24 raised roof aluminum tilt cab capable of seating ten 10 firefighters The roof shall be raised 24 with windows in the upper portion above the doors The raised roof shall extend from the back of the cab to the center of the front doors to provide additional headroom for the driver and officer The cab shall be of the Eurospace interior design allowing for easy communication inside the cab The cab overall length shall be 150 38 with 74 00 from the centerline of the front axle to the back of the cab The rear cab wall shall be 090 thick aluminum The rear floor to the
132. right White Board shall be approximately and located one 1 each side of walk thru on rear wall of cab SLIDE OUT PENCIL DRAWERS There will be one 1 slide out pencil drawer provided under the desk top SVI 603 03 27 07 Page 34 of 86 Maui Police Department SVI Trucks Production Specification CO 3 REMOTE KEYLESS ENTRY SYSTEM The Spartan custom cab manual door locks shall be equipped with a POP Locks electric actuated door locking system All cab doors shall be locked and un locked from a numeric key pad located adjacent to the drivers door All doors shall have a manual key operated override capability in the event of a failure of the electric lock system All cab doors shall be keyed alike Four 4 hand held remote controls shall be provided for controlling the cab Note Alert notification function with security system shall be investigated and if avalible provided prior to assembly Maui Police Department shall provide information on Digital Security local company INTERCOM SYSTEM A customer supplied Sigtronics 4 position intercom shall be installed Equipment to be provided by customer Harmer Communication SVI 603 03 27 07 Page 35 of 86 Maui Police Department SVI Trucks Production Specification CO 3 BODY DESIGN The importance of public safety associated with emergency vehicles require that the construction of this vehicle meet the following specifications These specifications are written to establish the mi
133. riod of ten 10 years Warranty conditions may apply and shall be listed in the detailed warranty document that shall be provided upon request PAINT FRAME AND CHASSIS UNDER CARRIAGE The chassis under carriage consisting of frame axles driveline running gear battery boxes air tanks and other assorted chassis mounted components shall be painted with standard black paint Paint shall be applied before airlines and electrical wiring is installed CHASSIS WHEELBASE The chassis wheelbase shall be 238 CA shall be 164 AF shall be 100 5 FRAME The frame side rails shall be black powder coated C channel type 10 25 x 3 5 x 38 with an inner channel 9 44 x 3 13 x 38 of 110 000 psi minimum yield high strength steel a RBM of 3 315 214 inch pounds and a section modulus of 30 14 cubic inches A minimum of seven 7 fully gusseted bolted assembly crossmembers shall be installed using grade 8 flanged head bolts and flanged lock nuts The area between the axle suspension hangers shall be free of any holes or fasteners in the flanges No welding shall be incorporated in attachment of components All frame dimensional cutting shall be by a plasma cutter All relief areas shall be cut in with a minimum 2 radius at intersection points with ground smooth edges to prevent a stress focal point The frame and crossmembers shall carry a lifetime warranty to the original purchaser OVERALL HEIGHT The height of the vehicle shall not exceed 135 fr
134. rive system enclosure with shield wiper high quality camera and lens The camera system shall be a high resolution unit with Lowlighta color technology and a 176X zoom lens 22X optical 8X electronic The camera control system shall contain one 1 KBD300A PTZ control unit and one 1 CM6700 MXB2 switcher controller VEHICLE SATELLITE COMMUNICATIONS SYSTEM AVL Technologies Agiosat model AG1288 8WRMV 8 Watt Ku Band Mobile VSAT Antenna System shall be installed on vehicle to include 4 00 Mbps maximum uplink from field location to hub Vipersat Enabled 1 2 Meter Prime Focus Offset Reflector Feedhorn Assembly with Transmit Reject Filter plus LNB RF Interface Terrasat IBUC 8 Watt Ku band Block Upconverter Waveguide WR 75 Flex from Feed Assembly Coax RG59 run from feed to base plus 15 ft Pallet Mount for Permanent Vehicle Integration Electrical Interface 15 ft Cable with Connectors for Controller TracStar One button Full Function Rackmount Auto deploy Controller Peaking and Cross Pol Adjustment using GPS Compass and Level Sensor Inputs Certified for Auto commissioning on Agiosat North American Networks CDM570L L Band Satellite Modem Data rate 2 4 kbps 5 Mbps BPSK QPSK OQPSK Turbo Board IP Module VMS license 24 or 48VDC BUC Power Supply Advantech SatNet S4100 DVB S2 S Satellite Modem High speed Receive Link for the Agiosat Network platform up to 36 Mbps Also capable of 4 Mbps uplink back to satellite on a stand alone basis Cisc
135. rs or though a hooded vent opening in the compartment roof The louvers or hooded opening shall provide adequate air flow for operation of the generator in stationary or moving position with the compartment doors closed for only a short period of time For prolonged operation the compartment doors must be open MANUALS AND SCHEMATICS Two 2 complete manuals on parts list maintenance wiring schematics hydraulic schematics circuit boards voltage regulator board and other components shall be provided on delivery GENERATOR COMPARTMENT INSULATION The generator compartment shall be provided with heavy duty sound insulation applied to walls and ceiling Insulation shall have a high temperatures rating with a foil facing and attached to walls with a positive type fasteners glue type adhesive will not be acceptable GENERATOR CONTROLS In addition to generator controls provided at the generator Controls shall be provided in the cab at the 12 volt control panel The following controls shall be provided One 1 pre heat switch if generator is diesel One 1 start stop switch One 1 generator running indicator light Any generator remote gauges to be located adjacent to load center panel in body walk in CIRCUIT BREAKER BOX There shall be one 1 Paneltronics line voltage distribution panel and breaker panel located in the front command area of the body All circuit breakers shall be rated to the wire size and load demand
136. s personnel of electrical system failure or a system voltage of less that 11 7 volts DC for a 12 volt nominal system for more that 120 seconds shall be considered a test failure LOW VOLTAGE ALARM TEST Following completion of the above tests the engine shall be shut off The total continuous electrical load shall be activated and shall continue to be applied until the excessive battery discharge alarm activates The battery voltage shall be measured at the battery terminals With the load still applied a reading of less that 11 7 volts DC for a 12 volt nominal system shall be considered a test failure The battery system shall then be capable of restarting the engine Failure to restart the engine shall be considered test failure SVI 603 03 27 07 Page 5 of 86 Maui Police Department SVI Trucks Production Specification CO 3 DOCUMENTATION Documentation of the electrical system performance test shall be provided with delivered apparatus In addition a written load analysis including the following Nameplate rating of alternator Alternator rating under the conditions specified in NFPA 1901 13 3 2 Each component load specified in NFPA 1901 13 3 3 comprising the minimum continuous load Additional loads that when added to the minimum continuous load determine the total connected load Each individual intermittent load 120 240 VOLT AC NFPA TEST The apparatus 120 240 volt electrical system shall be tested and certifi
137. shall have a back pressure protection valve This valve shall hold back 70 pounds in the air brake system and shall only allow air to pass into the system when the ignition switch is on and the parking brake is set A red flashing warning light will be visible to the driver to warn when a light tower is out of roof nested position A pneumatic kit to raise and lower the mast shall include air control valve 0 160 psig air gauge regulator 0 30 psig air gauge The mast shall be of a free standing design non guyed and use high strength heat treated aluminum alloy tubes and collars Each mast section tube shall have two full length external keys and nominal 095 wall thickness collars with matching keyways to maintain directional azimuth Each mast section and collar shall be of the low friction synthetic bearings for smooth operation and longer life Bumpers shall be supplied to reduce shock on extension and retraction All exterior aluminum surfaces shall be anodized and sealed Fasteners and fittings shall be plated steel or stainless steel for corrosion resistance Mast shall be mounted using an internal roof mounting kit One 1 maintenance and instruction manual will be provided for the towers on delivery Wiring schematic air piping schematic and installation diagrams shall be provided with the manual Manufacturer s blueprint of tower complete parts list and bill of materials for towers provided with manuals TELESCOPING LIGHT MAST M
138. sive engine coolant temperature High Trans Temp indicates excessive transmission oil temperature Low Air indicates low air pressure in either system one or system two Low Coolant Level indicates low engine coolant level 1 Low Oil Level indicates low engine oil level 1 Air Filter indicates excessive engine air intake restriction YELLOW LAMPS Check Engine indicates non critical engine fault Check Trans indicates transmission fault Wait to Start indicates active engine air preheat cycle 2 ABS indicates anti lock brake system fault Water in Fuel indicates presence of water in fuel filter 1 Engine Maint indicates engine maintenance is required 1 SVI 603 03 27 07 Page 23 of 86 Maui Police Department SVI Trucks Production Specification CO 3 GREEN LAMPS Left and Right turn signal indicators Aux Brake Active indicates secondary braking device is active 1 High Idle indicates engine high idle is active 1 Low Trac indicates low wheel traction for automatic traction control ATC equipped vehicles also indicates mud snow mode is active for ATC system 1 BLUE LAMP High beam indicator The instrumentation system shall provide a constant audible alarm for the following situations Low air pressure Low engine oil pressure High engine coolant temperature High transmission oil temperature Low coolant level 1 High or low system voltage Critical engine fault Stop Engine
139. st TV Antenna Radio Communications Equipment Dispatch Labor included in 10 AA 1310 Radio Communications Equipment Body Equipment to be provided by customer Harmer Communications Labor included in 10 AA 1310 Panasonic Telephone System MPD Provided CATV Modem Data Network Wiring Computer Workstations Printer Exterior Public Address System SVI Supplied Loose Equipment 2005 400 06 24 05 Equipment List Assorted Fastners Wheel chocks 2 folding for 44 dia tires Wheel Chocks Mounted Streamlight SL 20XP Flashlight Flashlight Mounted Portable Hannay Cable Reel 100 of 12 3 Cable BID DOCUMENTS 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 Maui Police Department SVI Trucks Production Specification CO 3 INSURANCE Bidder shall furnish with the bid one 1 certificate of insurance for Workman s Compensation and Employer s Liability Insurance for all employees General aggregate of 2 000 000 00 including products comprehensive operating aggregate Personal injury of 1 000 000 00 combined each occurrence Fire damage of 50 000 00 and Medical expense of 5 000 00 Automobile liability of 1 000 000 00 combined single limit including any auto all owned autos scheduled autos hired autos non owned autos and garage liability Excess umbrella liability coverage of 1 000 000 00 each occurrence All insurance policies must be maintained for the life of the contract must provide ten
140. stalled on the unit designed for large heavy duty vehicles with a GVWR over 23 000 pounds The system shall have four 4 mounting brackets welded to the chassis frame rails two 2 front and two 2 rear Each jack shall bolt to the bracket attached to the chassis frame Each jack has its own hydraulic reservoir and 12 volt DC motor wired to the chassis electrical system Jack pads have a 100 square inches surface to prevent sinking in soft ground Jacks shall be rated for lifting 17 000 pounds minimum each The system shall have a drive off safety feature If the vehicle ignition switch is on and any legs are not fully retracted a warning alarm will sound with the Deluxe Touch Pad fully automatic panel with sensor The system shall be provided with a 5 year limited warranty from Quadra Manufacturing Inc Leveling system shall be provided with a transmission interlock preventing transmission to be placed in gear until legs are retracted SVI 603 03 27 07 Page 32 of 86 Maui Police Department SVI Trucks Production Specification CO 3 CAB WINDOW TINT All cab windows except front windshields driver s and officer s door windows and body windows shall be provided with a 5 dark tint CAB COMMAND CENTER There shall be one 1 counter cabinet with hinged doors provided in the cab interior The cabinet shall be constructed of 1 8 smooth finish aluminum and finished with a dark gray hammer tone powder coat for a hard and durable surfa
141. surface oxidation or surface debris that may hinder the paint adhesion After the surface is machine finished a high quality acid etching base primer shall be applied Upon the application of required body fillers and their preparation the cab shall be primed with a coating designed for corrosion resistance and surface paint adhesion The entire cab then shall be coated with an intermediate solids or epoxy surfacer that is designed to fill minor surface defects provide an adhesive bond between the primer and the paint and improve the color and gloss retention of the color coats The cab shall be finish sanded with 360 grit paper seams sealed with SEM seal sealer and painted with two 2 to four 4 coats of an acrylic urethane type system designed not only for color retention but to resist acid rain and most atmospheric chemicals found on the fire ground or emergency scene The maximum overall film thickness of the top coat shall not exceed five 5 mils The standard PPG FBCH paint shall be warranted for ten 10 years against cracking checking or peeling and loss of gloss caused by chalking or fading other paint warranties will vary by manufacturer for example Sikkens FLNA or Dupont Imron 6000 Cab underside and doors shall be rustproofed with a ten 10 year or 100 000 mile warranty certificate against perforation issued in the Fire Department s name Cab to be painted White Paint brand and color HAND SAND AND BUFF FINISH The base
142. t Fire Research FCA200 S50 500W 120V Focus Make Fire Research Model Focus P N FC200 S50 Switch On Body one each side Scene Lights at the Rear of the Body gt Fire Research FCA200 M15 1500W 240V Focus Make Fire Research Model Focus P N FC200 M15 Switch On Body COMMAND TECH EQUIPMENT Command Area Tech Equipment DC power for the command area to be hot with the chassis master in the off position Power to come from additional batteries Bosch Surveillance Cameras Camera Pelco ES31C22 5N Pneumatic Mast Will Burt 7 30 Pneumatic Kit Nycoil Cable Conduit 7 30 Antenna Mount on Mast Mast Cover Camera Guard 03 27 2007 PART NO R8 10 1020 R8 20 1010 NB 00 1050 R6 10 1000 R6 10 1010 R6 20 1000 T2 00 1000 R6 08 0100 R6 08 0200 R6 10 1010 R6 20 1005 R6 20 1006 R6 20 1007 R6 21 1000 R6 21 1002 R6 22 0100 R6 22 0400 R6 30 0100 X0 00 1000 X0 05 1100 X0 10 1500 X0 10 A110 X0 60 1200 X0 60 A110 X0 90 1000 gt lt lt KK OK OX gt DESCRIPTION Will Burt 6 25 pneumatic mast Microwave Antenna Electronic Patch Panel Video Monitor System Bosch DVR Recorder 40 LCD Screen with Smart Board Camera Pelco ES31C22 5N Agiosat Networks System Equipment to be provided by customer SatCom Systems Inc Satallitte TV System Equipment to be provided by customer Harmer Communication Wingard Sensar Broadca
143. tem Walk in Generator Onan 12 kW Diesel Generator Mount In Compartment Generator Fuel Chassis Fuel Connections Generator Battery Chassis 12 Volt Connection Generator ShutDown Safety Shut Downs Generator Cooling Air Generator Manuals Generator Insulation Sound Thermal Generator Control Remote Control in Cab Load Center Paneltronics 120 240 Volt 200 A 1 Phase Shore Power 30 Amp Connection One 1 wired to specified inverter One 1 wired to outlets at each interior desk position Shore Power Plug Kussmaul 30 Amp Super Auto Eject Electric Auto eject Cover Yellow Shorepower Plug Location Above Generator Door Shore Power 100 Amp Connection 120 240 Volt Outlets Reels and Interior Lights N e ee Cee re Cee ire Cee l A A A A A A A aries CEs CEs Cen Ginn Cen Eons Cen Canes Cen Een Cte Ginn Cline O ee Cen CE Ul o En Gee i gt ee Cie Cen aE Cees 03 27 2007 PART NO R2 B0 1100 R2 D0 1100 R2 B0 2100 R2 D0 1100 R2 BC 1100 R2 D0 1100 R2 BF 1100 R2 BF A100 R2 BF A200 RO 10 1610 R1 10 1120 R1 15 1110 R1 15 1210 R1 15 1420 R1 15 1510 R1 15 1610 R1 15 1710 R1 30 1110 R1 30 1220 RO 94 1110 R2 10 1600 R2 10 2600 R2 10 4100 R2 10 5100 R5 10 1010 R5 30 1000 R5 30 1010 R5 A0 1140 R5 50 1000 R5 50 1001 R5 50 1010 R5 A0 1130 R5 50 1002 R5 50 1010 R5 A0 1130 R5 60 1000 R5 60 1040 R5 A0 1120 NA 00 1010 MB 11 1500 NB 00 1000 NB 00 3030 R8 10 2010 R8 A0
144. tension gravelshield shall be provided by the cab chassis manufacturer AIR HORN S The air horn s shall be supplied and installed by the cab chassis manufacturer EXHAUST The exhaust system shall be as provided by cab chassis manufacturer No other alternation or modifications are required ADDITIONAL BATTERIES Six 6 Optima Yellow Top group 31 battery s shall be provided and mounted on slide out tray located in Compartment S2 These additional batteries shall be completely separate from the cab chassis battery system and charged by the specified Kussmaul 75 amp DC power supply wired to the on board generator system CELLULAR PHONE ANTENNA INSTALLATION There shall be two 2 supplied Nextel cellular phone antennas installed on the unit The antenna location and termination location for each cellular phone shall be determined by the Maui Police Department RADIO ANTENNA INSTALLATION There shall be twenty six 26 radio s with antenna s installed in the completed unit Each radio shall be wired for with 12 VDC power and ground as required by radio manufacturer The antenna location and termination location for each radio shall be determined by the Maui Police Department See the detailed radio list in the communications portion of the specification MUDFLAPS There shall be rubber mudflaps furnished and installed behind each set of tires AUTOMATIC VEHICLE LEVELING SYSTEM A Quadra Manufacturing Inc Big Foot model QE 2 shall be in
145. terial or workmanship under normal use and conditions for the lifetime of the product In addition the MRK shall be provided with model FD 24 reinforced 16 gauge solid steel front door Removable key locked 16 gauge steel side panels with recessed lift handles model SPN 267 24 Integrated fan tops with proportional speed thermostatic fan control Vertical outlet strip model PD 2415SC NS and three 3 U type shelves A minimum 37 amp UPS uninterruptable power supplies with surge protection shall be located in data rack TELEX DISPATCH SYSTEM Two 2 customer provided Telex dispatch systems shall be installed in rear chassis cab area INTERIOR CABINET OVERHEAD There shall be two 2 overhead cabinets provided above streetside of L desk in rear area of cab Cabinets shall be constructed of 1 8 smooth finish aluminum and painted with a hammer tone powder coat paint finish for a hard durable surface Paint color shall be gray The above cabinet s shall have sliding aluminum doors SVI 603 03 27 07 Page 33 of 86 Maui Police Department SVI Trucks Production Specification CO 3 REAR CAB L SHAPED DESK The rear portion of cab shall be provided with an L shaped desk extending from the curbside data rack to streetside directly behind the driver and officer and extending to the rear wall of the cab on the streetside The desk shall be 18 deep and located approximately 30 from the floor The front edge of desk top shall be reinforce
146. terior of apparatus shall be provided with a desk top full width of slide out which shall be 24 deep and located approximately 30 from floor The front edge of the desk top shall be reinforced with 2 x 2 tubing in order to support a person sitting on the edge of the desk The desk top surface shall be fabricated of 3 16 smooth aluminum It shall have a 2 vertical back splash along the back edge and a 2 vertical downward edge along front to cover the 2 x 2 reinforcement There shall be 2 1 2 diameter holes with plastic edge grommet provided at each rear corner for wiring of future equipment located on the desk top SLIDE OUT PENCIL DRAWERS There will be one 1 slide out pencil drawer provided under the desk top INTERIOR SEATS Two 2 Herman Miller highly adjustable Aeron Chairs furnished and installed in the body command area slide out Each chair shall have a Kinemat tilt mechanism that allows the body to pivot naturally and simultaneously at the ankles knees and hips providing a smooth ride and proper support from forward leaning to reclining postures There shall be lumbar adjustment vertically through 4 1 2 inch height range Its depth can be set at 3 4 inch or 1 1 4 inches There shall be a suspension system fabricated from unique Pellicle material the Aeron chair distributes weight evenly over the seat and back conforming to each person s shape The material also lets air pass through adding to long term comfort by preventing
147. terior side walls from top of exterior compartments to ceiling height The interior panels shall be installed with sheet metal screws with white plastic plugs covering the screws The seams between FRP panels interior corners and exterior corners shall be trimmed with white plastic molding The interior finish shall be bright white pebble grain FRP SVI 603 03 27 07 Page 53 of 86 Maui Police Department SVI Trucks Production Specification CO 3 INTERIOR WALKWAY FLOOR There shall be Lonseal Loncoin Il material installed on the floor substrate The material shall be installed with Manufacturer recommended adhesives Care shall be taken to eliminate seams The material shall be black in color Loncoin lI Black Onyx INTERIOR SUB FLOOR Above the body subframe shall be an isolation sheet that shall prevent outside elements from permeating the full length sound and thermal barrier of 3 4 thick marine grade plywood The sheet shall be fabricated from the same type of material as is used in the subframe The isolation sheet shall be flanged on both sides with a 1 high vertical break AIR CONDITIONER SYSTEM The apparatus body shall be provided with an off roof Dometic Cruisair air conditioning system The system shall consist of a three 3 remote mount Type EBO 230 volt AC cooling units mounted in the interior rooms one 1 14 000 Btu hr 530 cfm 1 6 amp and two 2 7 000 Btu hr 300 cfm 1 5 amp each Each cooling unit is a compact
148. th integral regulator and 10 screw AC terminals shall be installed The package shall include a CAT C 9 Service Manual and a CAT C 9 Trobleshooting Guide and any other applicable manuals ENGINE OIL LEVEL CHECK A low engine oil level switch shall be provided that will indicate when the engine oil is approximately four 4 quarts or more low The switch shall light a red LOW OIL LEVEL indicator light in the dash The indicator shall only function while the ignition switch is on and the engine is not running FUEL SHUT OFF VALVE AT FUEL TANK A fuel shutoff valve shall be installed in the fuel draw line near the fuel tank to allow maintenance to be performed with minimal loss of fuel TAIL PIPE CHROME EXTENSION A radiused chrome exhaust tail pipe extension to direct exhaust gases downward which terminates on the right hand side of the chassis forward of the rear tires shall be installed with a galvaneal band clamp AIR CLEANER The air cleaner shall be Farr 62891 001 dry type with a replaceable element it shall have an outside air intake with an ember separator filter and an indicator light in the warning light cluster to show when the air cleaner element requires replacement SVI 603 03 27 07 Page 20 of 86 Maui Police Department SVI Trucks Production Specification CO 3 STOP TAIL TURN AND BACK UP LIGHT WIRING Individual wires shall be run to the rear of the chassis for the stop light turn signal tail light and ba
149. the compartment door design metal thickness and attachments must be strictly adhered to Door openings exceeding 32 in width shall be double door openings with the handle door at front The handle door shall be first opening with a 3 4 overlap of the second door The second door shall have a 3 4 interior overlap and be held closed by the first opening door The doors shall be flush mounted so that the outer surface is in line with the side body surface Lap or bevel type constructed doors doors framed with extrusions or doors requiring rubber bumpers to prevent unnecessary contact are NOT ACCEPTABLE The compartment doors shall be all aluminum 3003H 14 alloy construction The exterior panel shall be of 1 8 thickness smooth plate aluminum and the interior panel shall be of 3 16 thickness smooth plate aluminum Lighter gauge material will NOT BE ACCEPTABLE in these areas The double panel doors shall be 1 3 4 thick to completely enclose the door latching assembly Doors shall have drain hole openings for drainage and ventilation Compartment door openings shall be sealed with closed cell automotive type rubber molding to provide a weather resistant seal around door In addition rubber molding shall be provided along hinge to prevent moisture entry Open cell foam type rubber moldings are NOT ACCEPTABLE Compartment doors shall have full height 14 gauge stainless steel hinge with 1 4 stainless steel pin The hinges shall be bolted to the door
150. the interior height of the body walkway The installed module shall provide a water tight seal in both the fully extended and the retracted positions The slide out section shall utilize smooth operating quiet gear and rack system Systems using hydraulic components will NOT BE ACCEPTABLE There shall be only two 2 serviceable items the 12 vdc motor and the electric control switch The system shall use a heavy duty positive 100 synchronized gear and rack system to prevent binding during the extend or retract cycle The rack system shall be rated for up to 1 500 pounds A 3 position momentary type rocker switch shall be used to operate the slide out wall system A manual override shall be provided in the event of a system failure The slide out section shall be framed with 2 x 2 x 1 4 6061 T6 alloy aluminum The frame structure shall be covered with no less than 1 8 thick 3003 H14 smooth aluminum There shall be two 2 flashing LED warning lights with red lenses one at each end of the slide out section The lights shall activate and be visible when the unit is extended All electrical wiring installed in the slide out wall shall run through a boxed type conduit at the lower corner of the system All wiring shall be enclosed in a flexible moisture resistant reinforced conduit with proper seal tight connectors and hardware Access shall be provided for inspection of all wiring and the gear and rack mechanism The Command Center Slide o
151. ttom of the radiator to allow a single depth core allowing a more efficient and serviceable cooling system The transmission cooler shall be mounted in such a manner as not to extend below the chassis frame by more than 1 allowing greater approach angles and ground clearance Transmission Heat Exchanger Non Retarder Application The transmission oil to water heat exchanger shall be installed to aid in cold climate conditions maintaining the transmission temperature at the operational level SVI 603 03 27 07 Page 19 of 86 Maui Police Department SVI Trucks Production Specification CO 3 SYNTHETIC TRANSMISSION FLUID Castrol Transynd or an equivalent synthetic TES 295 transmission fluid shall be utilized to fill the EVS transmission TRANSMISSION MODE The transmission upon start up will select four 4 speed operation By pressing the mode switch on the shift pad mode on provides five 5 speed overdrive TRANSMISSION WARRANTY The Allison 3000 EVS series transmission shall be warranted for a period of five 5 years with unlimited mileage Parts and labor shall be included in the warranty ALLISON 3000 EVS TRANSMISSION SERVICE MANUALS The following Allison 3000 EVS transmission service and reference manuals shall be provided PC2809EN Parts Catalog SM2148EN Service Manual GN2055EN Technician Guide TS2973EN Electronic Controls Troubleshooting Manual ALTERNATOR A 270 amp 12 volt Leece Neville alternator model 4949PA wi
152. ture in the rear wall and the roof The opening shall be completed by the custom cab chassis manufacturer to assure proper cab structural integrity and completed final interior finish INTERIOR CAB AND BODY WINDOW COVERS An interior window cover shall be provided for each window of the chassis cab and the apparatus body The window covers shall be of Coverlight Select 22 oz material with snap on type fasteners The snap on fasteners shall be installed around each window in the cab and body to allow each window to be covered Window covers will be light gray Note covers for driver amp officer windshields shall also be provided SVI 603 03 27 07 Page 51 of 86 Maui Police Department SVI Trucks Production Specification CO 3 DROP DOWN CAB CURTAIN A drop down style curtain will be mounted from the ceiling of the cab It shall be positioned directly behind the Driver and Officer seats so as to separate the front and rear portions of the chassis cab The curtain shall be made of Coverlight Select 22 oz material and weighted along the bottom edge When the curtain is not in use it shall be rolled up with snap on type fasteners securing it against the cab ceiling The curtain will be light gray Window covers shall be provided with Velcro or equal straps at top of window so covers can be rolled up and held open ESCAPE HATCH AND SKYLIGHT The center of the apparatus roof area shall be specially reinforced for the installation of a hinged door
153. ure Therefore pop rivets shall NOT be used in the construction of the structural portions of the body This includes side body sheets inner panels of compartment doors and any other structural portions of the body SVI 603 03 27 07 Page 36 of 86 Maui Police Department SVI Trucks Production Specification CO 3 EXTERIOR ALUMINUM BODY The fabrication of the rescue body shall be constructed from aluminum 3003H 14 alloy smooth plate This shall include compartment front panel vertical side sheets side upper rollover panels rear panels and compartment door frames The body compartment floors and exterior panels shall be constructed with not less than 3 16 187 aluminum 3003H 14 smooth plate Interior compartment dividing walls shall be constructed with not less than 1 8 125 aluminum 3003H 14 smooth plate Lighter gauge sheet metal will not be acceptable in these areas The door side frame openings shall be formed C channel design An electrical wiring conduit raceway running the full length of exterior compartments shall be provided This raceway shall contain all 12 volt wiring running to the rear of the apparatus permitting easy accessibility to wiring Individual compartment modules with dead air space voids between compartments will not be an acceptable method of compartment construction The compartments shall be an integral part of the body construction Compartment floors from front of body to ahead of rear axle also from
154. ut must be able to withstand years of rugged service and wear For this reason this design metal thickness and attachments must be strictly adhered to RV type slide outs or slide outs using light weight metal or fiberglass shall not be acceptable WINDOW One 1 18 wide x 22 high vertical sliding window shall be installed in the forward facing wall of the slide out module WINDOW One 1 18 wide x 22 high vertical sliding window shall be installed in the rearward facing wall of the slide out module INTERIOR CABINET COUNTER HEIGHT There shall be one 1 interior counter height cabinet s provided below desk and between specified seats Cabinet s shall be constructed of 1 8 smooth finish aluminum and painted with a hammer tone powder coat paint finish for a hard durable surface Paint color shall be gray or black Each cabinet shall be approximately 27 W x 28 H x 22 D The above cabinet s shall have a vertically hinged aluminum door s and painted with a hammer tone powder coat paint finish to match cabinet color choice There shall be two 2 vertically adjustable shelves in each of the above cabinets INTERIOR CABINET OVERHEAD There shall be three 3 overhead cabinet s provided on interior Cabinet s shall be constructed of 1 8 smooth finish aluminum and painted with a hammer tone powder coat paint finish for a hard durable surface Paint color shall be gray Each cabinet shall be approximately 36 x 14 x 14
155. y accessible for generator service FUEL SYSTEM The generator fuel system shall be plumbed to the chassis main fuel tank A separate fuel line shall be installed directly from the tank not connected to the truck engine fuel line system The generator fuel line shall be properly protected and secured inside of chassis frame A shut off valve shall be provided between the generator and fuel line as it enters the compartment SVI 603 03 27 07 Page 73 of 86 Maui Police Department SVI Trucks Production Specification CO 3 STARTING SYSTEM The generator starting system shall be powered by chassis battery system with heavy duty stranded copper cables The starter line shall by pass the chassis master switch to permit generator operation when the apparatus engine is not running This starter line shall be of sufficient size for the generator adequately protected and supported inside the chassis frame area COOLING Since the generator is radiator cooled the ventilation of the generator is crucial The installation shall permit operation of the unit both while the apparatus is stationary or while it is in motion The incoming air flow shall be though stamped louvers in compartment walls and or doors or though a hooded vent opening in the compartment roof The louvers or hooded opening shall provide adequate air flow for operation of the generator in stationary or moving position with the compartment doors closed for only a short period of tim
156. ystem shall be responsible for providing power management functions as well as load shedding The warning light system shall be controlled by the multiplex system The system shall be capable of displaying text and or graphic messages on a display module The system shall be based on solid state technology and shall include self contained diagnostic indicators COLOR VISTA Ill DISPLAY There shall be two 2 chassis supplied full color display that incorporates seven switches with custom legends and has a wide temperature operating range The display panel shall be the point of interaction with the entire 12 volt electrical system The display shall respond with text and graphic images to provide fault and condition messages to the Operator The 12 volt electrical distribution panel shall be located in the curbside front lower compartment SVI 603 03 27 07 Page 62 of 86 Maui Police Department SVI Trucks Production Specification CO 3 BATTERY SYSTEM The battery connectors shall be heavy duty type with cables terminating in heat shrink loom Heavy duty battery cables shall provide maximum power to the electrical system The cables shall be shielded from exhaust tubing and the muffler Large rubber grommets shall be provided where cables enter the battery compartment BATTERY SWITCH One 1 battery On Off switch with green BATTERY ON indicator shall be installed in cab within easy reach of Driver to activate the battery system The swit

Specifications

Contents

Download Pdf Manuals

Related Search

Related Contents