2001 impreza service manual quick reference index body section
Contents
1. 3 Remove quarter pillar trim lt Ref to El 30 Re moval Rear Quarter Trim gt gt 4 Remove rear shelf trim lt Ref to El 35 REMOV AL Rear Shelf Trim gt 5 Remove bolts and then detach seat belt ne 255 5 ES RE0005 3 INNER BELT SEDAN BODY 1 Remove the rear cushion lt Ref to SE 11 RE MOVAL Rear Seat gt 2 Remove bolts and then detach inner belt Ee SCH 4 OUTER BELT SIDE WAGON BODY 1 Remove luggage floor mat lt Ref to El 38 RE MOVAL Luggage Floor Mat gt 2 Remove rear seat lt Ref to SE 11 REMOVAL Rear Seat gt 3 Remove side sill rear lower cover lt Ref to El 29 REMOVAL Lower Inner Trim gt 4 Remove seat belt lower anchor bolt RE0006 5 Remove rear quarter trim lt Ref to El 30 RE MOVAL Rear Quarter Trim gt SB 10 REAR SEAT BELT SEAT BELT SYSTEM 6 Remove bolts and then detach outer belt side RE0007 5 OUTER BELT CENTER WAGON BODY 1 Loosen shoulder anchor bolt and then detach shoulder anchor from quarter pillar 2 Remove quarter trim lt Ref to El 30 REMOVAL Rear Quarter Trim gt 3 Remove three bolts and then detach outer belt center RE0009 6 INNER BELT WAGON BODY 1 Remove the rear cushion 2 Remove bolt and then detach inner belt B5M0912. DEPLOYMENT e Used for deploying the pretensioner e Used with DEPLOYMENT TOOL 98299PA030 B5M1115 98299PA030 DEPLOYMENT TOOL SB 6 Used for deploying the pretensioner e Used with ADAPTER A DEPLOYMENT 98299FC030 INSPECTION LOCATIONS AFTER A COLLISION SEAT BELT SYSTEM 2 Inspection Locations After a Collision A INSPECTION Check for the following and then replace with new parts if necessary e Center pillar lower garnish is discolored or cracked Wire harness and or connector is damaged SB 7 FRONT SEAT BELT SEAT BELT SYSTEM 3 Front Seat Belt A REMOVAL 1 OUTER BELT FRONT 1 Fold backrest all the way forward and then move front seat all the way forward 2 Turn ignition switch OFF disconnect ground ca ble from battery and wait for more 20 seconds be fore starting work 3 Remove center pillar lower trim lt Ref to El 29 REMOVAL Lower Inner Trim gt 4 Remove anchor cover Loosen shoulder anchor bolt and then detach shoulder anchor from center pillar RE0003 6 Disconnect yellow connector of pretensioner harness and remove outer belt front CAUTION Do not drop or apply any impact to preten sioner e Pretensioner and bracket should be treated as an assembly Do not attempt to disassemble it 2 INNER BELT FRONT 1 Disconnect connector 2 Remove anchor bolt and then detach inner
3. 2001 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX BODY SECTION HVAC SYSTEM HEATER VENTILATOR AND A C HVAC SYSTEM AUTO A C DIAGNOSTICS AIRBAG SYSTEM AIRBAG SYSTEM DIAGNOSTICS This service manual has been prepared to provide SUBARU service personnel with the necessary information and data for the correct maintenance and repair of SUBARU vehicles LIGHTING SYSTEM This manual includes the procedures for maintenance disassembling reas sembling inspection and adjustment of WIPER AND WASHER SYSTEMS components and diagnostics for guid ance of experienced mechanics Please peruse and utilize this manual ENTERTAINMENT fully to ensure complete repair work for satisfying our customers by keeping their vehicle in optimum condition COMMUNICATION SYSTEM When replacement of parts during repair work is needed be sure to use SUBARU genuine parts GLASS WINDOWS MIRRORS GW SEAT BELT SYSTEM BODY STRUCTURE BS INSTRUMENTATION DRIVER INFO IDI SEATS SE SECURITY AND LOCKS SL IMMOBILIZER DIAGNOSTICS IM SUNROOF T TOP CONVERTIBLE cp SUNROOF All information illustration and specifi cations contained in this manual are based on the latest product information available at the time of publication approval EXTERIOR INTERIOR TRIM El FUJI HEAVY INDUSTRIES LTD G1830GE6 et E ti 2001 IMPREZA SERVICE MANUAL QUICK REFERENCE INDEX BODY SECTION CRUISE CONTROL SYSTEM CC CRUISE CO
4. 9 SB 11 REAR SEAT BELT SEAT BELT SYSTEM B INSTALLATION 1 OUTER BELT SIDE SEDAN BODY Install in the reverse order of removal CAUTION e During installation make sure that seat belts are not twisted e After installation make sure that seat belts can be smoothly extended and wound 2 OUTER BELT CENTER SEDAN BODY Install in the reverse order of removal CAUTION e During installation make sure that seat belts are not twisted e After installation make sure that seat belts can be smoothly extended and wound 3 INNER BELT SEDAN BODY Install in the reverse order of removal CAUTION During installation make sure that seat belts are not twisted 4 OUTER BELT SIDE WAGON BODY Install in the reverse order of removal CAUTION e During installation make sure that seat belts are not twisted e After installation make sure that seat belts can be smoothly extended and wound 5 OUTER BELT CENTER WAGON BODY Install in the reverse order of removal CAUTION e During installation make sure that seat belts are not twisted e After installation make sure that seat belts are smoothly extended and wound 6 INNER BELT WAGON BODY Install in the reverse order of removal CAUTION During installation make sure that seat belts are not twisted C INSPECTION 1 OUTER BELT SIDE SEDAN BODY Check for the following and replace with new parts if necessary Seat belt is slac
5. NTROL SYSTEM CC DIAGNOSTICS G1830GE6 ES SEAT BELT SYSTEM Page 1 General Description CERN dE iss 2 2 Inspection Locations After a Collision EE 7 3 FOT Seat Belt TE 8 4 Rear Seat B S 10 5 Disposal of Pretensioner 13 GENERAL DESCRIPTION SEAT BELT SYSTEM 1 General Description A COMPONENT 1 FRONT SEAT BELT BO0239 1 Adjuster anchor ASSY Tightening torque N m kgf m ft lb 2 Anchor cover T1 7 5 0 76 5 5 3 Outer belt ASSY T2 30 3 1 22 4 Inner belt ASSY 53 5 4 39 SB 2 GENERAL DESCRIPTION SEAT BELT SYSTEM 2 REAR SEAT BELT SEDAN BODY BO0240 1 Outer seat belt RH 5 Inner seat belt CENTER Tightening torque N m kgf m ft lb 2 Outer seat belt CENTER 6 Inner seat belt LH T 30 3 1 22 3 Outer seat belt LH 7 Case center ELR T2 30 3 1 22 4 Inner seat belt RH T3 53 5 4 39 GENERAL DESCRIPTION SEAT BELT SYSTEM 3 REAR SEAT BELT WAGON BODY BO0241 1 Outer seat belt RH 5 Inner seat belt LH Tightening torque N m kgf m ft lb 2 Outer seat belt CENTER T1 30 3 1 22 3 Outer seat belt LH T2 53 5 4 39 4 Inner seat belt RH SB 4 GENERAL DESCRIPTION B CAUTION e Before starting turn the ignition switch OFF dis conn
6. belt 55 0234 5 8 FRONT SEAT BELT B INSTALLATION 1 OUTER BELT FRONT Install in the reverse order of removal CAUTION The parts on left and right are not identical Before installation make sure that the correct part is used Be careful not to twist belts during installa tion 2 INNER BELT FRONT Install in the reverse order of removal SEAT BELT SYSTEM C INSPECTION 1 OUTER BELT FRONT Check for the following and replace with new parts if necessary Pretensioner is cracked or deformed Seat belt is slackened bent or frayed Seat belt is abnormally wound or extended 2 INNER BELT FRONT Check for the following and replace with new parts if necessary Inner belt is deformed or damaged e Seat belt buckle is engaged improperly SB 9 REAR SEAT BELT SEAT BELT SYSTEM 4 Rear Seat Belt A REMOVAL 1 OUTER BELT SIDE SEDAN BODY 1 Remove rear seat lt Ref to SE 11 REMOVAL Rear Seat gt 2 Remove side sill rear lower cover lt Ref to El 29 REMOVAL Lower Inner Trim gt 3 Remove seat belt lower anchor bolt RE0010 4 Remove quarter pillar trim lt Ref to El 30 RE MOVAL Rear Quarter Trim gt 5 Remove bolts and then detach seat belt RE0004 2 OUTER BELT CENTER SEDAN BODY 1 Remove rear seat lt Ref to SE 11 REMOVAL Rear Seat gt 2 Remove seat belt lower anchor bolt
7. ect the battery ground cable and wait for 20 seconds or more The pretension system has a backup power source The pretensioner might deploy if you do not wait for 20 seconds or more before starting work Do not drop or apply any impact to the preten sioner If oil grease or water gets on the pretensioner wipe it off immediately with a dry cloth Do not expose the pretensioner to high tempera ture or flame Do not allow current to flow through or voltage to reach the pretensioner Do not use a Circuit tester to check resistance of the pretensioner Do not disassemble or attempt to repair the pre tensioner If it is dented cracked or deformed re place it with a new one Do not use the air bag or pretensioner parts from other vehicles Always replace parts with new parts e When handling a seat belt with a deployed pre tensioner wear gloves and goggles Wash your hands afterwards Do not re use a seat belt with a deployed preten sioner again Be sure to deploy pretensioner before disposal lt Ref to SB 13 OPERATION Disposal of Preten sioner gt If the material gets in your eyes or on your skin during deployment wash it away with clean water and then consult a doctor SB 5 SEAT BELT SYSTEM SEAT BELT SYSTEM GENERAL DESCRIPTION C PREPARATION TOOL 1 SPECIAL TOOLS ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS B5M1114 98299FE010 ADAPTER C
8. ensioner is especially hot Leave it unattended for 40 minutes Do not let water get on the deployed preten sioner SB 15 DISPOSAL OF PRETENSIONER SEAT BELT SYSTEM SB 16
9. il just before deployment of the pretension er Di S5M0309B 7 Connect adpter C deployment connector and pretensioner yellow connector SB 13 DISPOSAL OF PRETENSIONER SEAT BELT SYSTEM 8 Extend the deployment tool to the limit and make sure that vehicle is empty Close all windows sunroof and rear gate completely B5M1068 9 Move the battery at least 5 m 16 ft from the ve hicle and secure the nearby area Connect the de ployment tool alligator clip to the battery minus terminal 10 Connect the other terminal of deployment tool to the battery plus terminal Then deploy the pre tensioner G5M0531 CAUTION e After deployment pretensioner is especially hot Leave it unattended for 40 minutes Do not let water get on the deployed preten sioner 11 Remove outer belt front lt Ref to SB 8 Re moval gt 12 Wrap the deployed pretensioner in an airtight vinyl bag and then discard it B5M0500 2 DEPLOYING AFTER REMOVAL FROM VEHICLE 1 Fold backrest all the way forward then move front seat all the way forward 2 Turn ignition switch OFF disconnect the ground cable from the battery and wait for more than 20 seconds before starting work 3 Remove outer belt front lt Ref to SB 8 Re moval gt 4 Cut off seat belt as close to retractor as possible xO B5M0494 5 Short terminal to alligator clip furnished as a de
10. ise be sure to warn people in the area and do not allow anyone within a 5 meter 16 ft radius of the disposal site Some smoke will be emitted after deployment of the prettensioners Therefore it must be deployed in a well ventilated area with no smoke alarms nearby Wear gloves goggles and earplugs during this operation Wash your hands afterwards e After deployment the pretensioner is especially hot Leave it unattended for 40 minutes and then discard it Do not let water get on the deployed pretension er e Wrap the deployed the pretensioner in an airtight vinyl bag and then discard it H circumstances do not permit pretensioner de ployment contact a SUBARU dealer SEAT BELT SYSTEM B OPERATION 1 DEPLOYING WHILE INSTALLED IN VE HICLE 1 Fold backrest all the way forward and then move front seat all the way forward 2 Turn ignition switch OFF disconnect the ground cable from the battery and wait for more than 20 seconds before starting work 3 Remove center pillar lower trim lt Ref to El 29 REMOVAL Lower Inner Trim gt 4 Disconnect yellow connector from pretensioner a B5M0918A lligator clip furnished as de 5 Short terminal to ployment tool A 6 Connect the deployment tool and adapter C de ployment B Deployment tool Part No 98299PA030 Adapter C deployment Part No 98299FE010 CAUTION The deployment tool should be kept shorted unt
11. kened bent or frayed Seat belt is abnormally wound or extended 2 OUTER BELT CENTER SEDAN BODY Check for the following and replace with new parts if necessary Seat belt is slackened bent or frayed Seat belt is abnormally wound or extended 3 INNER BELT SEDAN BODY Check for the following and replace with new parts if necessary e Inner belt is deformed or damaged e Seat belt buckle is engaged improperly 4 OUTER BELT SIDE WAGON BODY Check for the following and replace with new parts if necessary Seat belt is slackened bent or frayed Seat belt is abnormally wound or extended 5 OUTER BELT CENTER WAGON BODY Check for the following and replace with new parts if necessary Seat belt is slackened bent or frayed Seat belt is abnormally wound or extended 6 INNER BELT WAGON BODY Check for the following and replace with new parts if necessary Inner belt is deformed or damaged e Seat belt buckle is engaged improperly SB 12 DISPOSAL OF PRETENSIONER 5 Disposal of Pretensioner A CAUTION Do not discard undeployed pretensioners be cause they may cause serious personal injury when accidentally deployed e Deployment of the pretensioners should be done on a flat place free from any possible danger Avoid deploying outdoors during rainy or windy weather Do not drop or damage pretensioner e Because deploying the pretensioners causes high explosive no
12. ployment tool A 6 Connect the deployment tool and adapter C de ployment B Deployment tool Part No 98299PA030 Adapter C deployment Part No 98299FE010 CAUTION The deployment tool should be kept shorted until just before deployment of the pretension er SA B S5M0309B 7 Connect adapter C deployment connector and pretensioner yellow connector 8 Install pretensioner on the wheel with the tire Then bundle three wire automotive harness each with a sectional area of 1 25 mm 0 00194 sq in or more and bind them twofold around the preten sioner bracket and the wheel B5M0669 SB 14 DISPOSAL OF PRETENSIONER 9 Put three tires without the wheel on the tire in stalled with pretensioner Put on an additional tire with the wheel on top and then fasten them tight with rope ANE RH NN tututi He G5M0536 10 Move the battery at least 5 m 16 ft from the ve hicle and secure the nearby area Connect the de ployment tool alligator clip to the battery minus terminal 5 m 16 ft or MAE EE G5M0537 SEAT BELT SYSTEM 12 Wrap the deployed pretensioner in an airtight vinyl bag and discard it B5M0500 11 Connect the other terminal of deployment tool to the battery plus terminal Then deploy preten sioner G5M0531 CAUTION e After deployment pret
Download Pdf Manuals
Related Search