General Info. Tooling List Parts List
Contents
1. Part Axl 6 127 Race CorkSport Rear Motor Mount 2004 Mazda3 and 2007 Mazdaspeed 3 Thank you for purchasing the CorkSport Mazdaspeed 3 and Mazda 3 Rear Motor Mount Replacing your stock motor mount with the CorkSport motor mount will provide improved handling and road feel while maintaining a comfortable ride Designed as a direct OEM replacement the CorkSport Mazdaspeed 3 Rear Motor Mount will maintain OEM fitment while adding a large urethane thrust surface for added stiffness and improved responsiveness We hope you enjoy your new parts Please provide feedback at http www corksport com corksport mazdaspeed 3 mazda 3 race rear motor mount html Pre Installation Notes Make sure your vehicle is completely cooled down prior to starting installation If you are going to work on your car within an hour or two of having driven it use a fan to cool off the car as These instructions were written for reference only and the use of a factory service manual is fe recommended Please read these instructions thoroughly prior to starting installation oTt These installation instructions were written using a 2010 Mazdaspeed 3 Other year makes N E za and models will be similar Materials and Time General Info Tooling List Parts List ay Part Axl 6 127 Race 17mm Socket One 1 CorkSport Rear Engine Mount Time Est 0 75 hours 19mm Socket One 1 M12x1 25 100mm long Bolt Wrench Rating 2 5 3 8 Drive Ratchet2. One 1 M12x1 25 Nut Torque Wrench Optional 80 Durometer Insert Set Silicone Spray Need Help With Yourdnstallatione Call 360 260 C RK Part Axl 6 127 Race Detailed Instructions These installation instructions were written using a 2010 Mazdaspeed 3 Other year makes and models will be similar 1 Install the CorkSport Rear Motor Mount a Use a floor jack and jackstands to gain access to the underside of the vehicle Always make sure vehicle is properly supported before crawling or standing under vehicle g Always referto the floor jack and jack stand manufacturers instructions as well as the factory owners manual for your vehicle to determine jacking points and support points Alternately use an automotive lift to gain access to the underside of the vehicle Redundant support mechanisms are recommended b Locate and remove the three 19mm bolts that hold the rear motor mount bracket to the transmission and the one 17mm bolt holding the bracket to the motor mount shown circled in Once they are removed the bracket will come out easily c Remove the 17mm bolt holding the rear motor mount to the chassis and remove the factory engine mount shown circled in d Install the CorkSport motor mount in the location the factory mount was removed shown in place in e Replace the 17mm bolt removed in step 1c and torque the bolt to 54 66 ft lbs refer to f Replace the bracket and 19mm bolts re
3. moved in step 1b and torque the bolt to 54 66 ft lbs Be careful starting the three bolts that thread into the transmission The housing is aluminum and can bind easily refer to g Install the supplied 19mm bolt and nut and torque to 54 66ft lbs P v This completes the installation of your CorkSport Rear Motor Mount Check out our knowledgebase for additional install information If you purchased the optional 80 5 durometer please see the next page for instructions on replacing your urethane Need Help With Yourdnstallatione Call 360 260 CORK 1 of 2 Part Axl 6 127 Race CHKSPOFTC Detailed Instructions 2 Changing Polyurethane Durometer a With the Engine Mount out of the car push the sleeve out of the center This can be done witha 14mm socket and a small hammer see Figure 2a and Figure 2b Figure 2a Figure 2b b Pull out the polyurethane from the housing Shown Figure 2c c Reassemble the mount as you disassembled it Then replace the sleeve in the center Again this might require a small hammer Assembly shown in Figure 2a l fo Engine Mount Boay Figure 2c Need Help With Yourdnstallatione Call 360 260 CORK 2 of 2
Download Pdf Manuals
Related Search