INSTALLATION INSTRUCTIONS
Contents
1. DRAG SPECIALTIES PORK CHOP MIRRORS P N 0640 0191 INSTALLATION INSTRUCTIONS ATTENTION INSTALLER if other than owner Please forward this Instruction Sheet to the purchaser of this product These instructions contain valuable information necessary to the end user INTRODUCTION These instructions describe the procedure for properly installing the Pork Chop Mirrors on 1996 2007 FLHT models Review instructions carefully before beginning as they contain important information Please retain for future reference Particularly important information is distinguished in these instructions by the following notations NOTE A NOTE provides key information to make procedures easier or clearer o7 10 0 H A CAUTION Indicates special procedures that must be followed to avoid damage to the motorcycle and or accessories WARNING A WARNING Indicates special procedures that must be followed to avoid injury to a motorcycle operator or person inspecting or repairing the motorcycle TOOLS REQUIRED 3 16 drill bit and drill 4mm hex key wrench 1 8 hex key wrench 9 16 combination end wrench 1 2 open end wrench Masking tape Fine line marker pen PROCEDURE 1 With the rider sitting on the motorcycle in an upright position determine the location to mount the mirror on the inner fairing Install a layer of masking tape to the inner fairing at this location See Figure 1 NOTE Make sure that t2. mirror mounting location or relocate the conflicting item scribe the mounting hole locations of the mounting bracket onto the masking tape on the inner fairing See Figure 2 7 Carefully drill two 3 16 holes through the inner fairing in the scribed mark locations for each mirror WARNING When drilling the inner fairing make sure that you do not place any part of your hands fingers etc on the under side of the inner fairing to prevent drilling thorugh your body parts 8 Install the mirror brackets with the button head bolts using the flat washers and lock nuts on the inside of the fairing tighten firmly Do not use any type of thread locking compound on the bolts holding the mirror mounting bracket to the inner fairing as the inner fairing can react with the thread locking compound and may crack 4 Position the mirror on the inner fairing so the scribed 9 Adjust the mirrors to the desired location and tighten mounting hole marks line up with the mounting bracket the locking collars on the back of the mirrors to prevent Have the rider confirm once again that the mirror is in the unwanted movement of the mirror head Confirm that the proper location socket bolt that holds the mirror head to the mounting bracket is tight also 5 Repeat steps 1 through 4 for the opposite mirror 10 Re install the outer fairing NOTE Confirm that the mounting locations of both mirrors are symmetrical for better appearance WARNING Be
3. fore operating motorcycle be sure all hardware is tight 6 Remove the outer fairing If necessary see the appropriate service manual for instructions on removing the outer fairing DRAG SPECIALTIES 3501 Kennedy Rd PO Box 5222 Janesville WI 53547 5222 New Oct 2006 P N 0640 0191 Page 2 of 2
4. he location you choose to mount the mirror on is as flat as possible If you mount the mirror too far FIGURE 1 out on the inner fairing you will get into the curved part of the fairing and may distort or crack the inner fairing or the mirror mount when the mirror mounts are tightened We suggest the general location be about 1 2 to the rear of the inner outer fairing seam and about 5 out from the outer windshield mounting screw to the closest mirror mounting hole This should give the mirror approximately the same sight lines as the original OEM mirror and still give you a relatively flat mounting area 2 Holding the mirror in the desired mounting location have the rider confirm that the mounting location allows sufficient view to the rear Make sure that the mirror has adjustment movement in all four directions If not reposition the mounting bracket to allow sufficient adjustment in all directions DRAG SPECIALTIES 3501 Kennedy Rd PO Box 5222 Janesville WI 53547 5222 New Oct 2006 P N 0640 0191 Page 1 of 2 DRAG SPECIALTIES INSTALLATION INSTRUCTIONS PORK CHOP MIRRORS P N 0640 0191 NOTE Loosen the locking collar slightly on the back of the Inspect the underside of the inner fairing to mirror to allow easier mirror head positioning confirm that there is nothing interfering with the location you have chosen to drill the mounting holes If necessary move the 3 Holding the mirror bracket firmly in the desired location
Download Pdf Manuals
Related Search