Here - Hurst
Contents
1. leather boot TOOL flat blade screwdriver Technical Support 707 544 4761 10 www hurst shifters com STEP 39 optional Install the leather boot onto the with boot support except some 2015MY vehicles using the bi a y A Whi supplied tie wrap trim away excess tie and snap boot bezel into center console 40 Affix Hurst knob onto vehicle if using option above being sure to tighten jam nut up against the knob base Ensure that all gears can be smoothly and fully engaged without binding or rough movement Correct any problems prior to operating the vehicle NOTE We have encountered concerns from customers regarding an increase in audible noise as a result of operating harmonics and vibration that is directly transmitted through the shift linkage following the installation of the shifter The following components can be installed to reduce this noise vibration however are not intended to mask internal problems of the transmission clutch and related clutch components or engine components that may have been modified Each individual vehicle is different any may have different harmonics that change with varying vehicle driving wear and atmospheric conditions Thus the suggestions that follow may work better in some vehicles than others and may not completely eliminate vibration noise to certain customers satisfaction A fair amount of experimentation and testing may be required to reduce audible vibration noise to accepta2. 2015MY and newer models and will not be necessary to reconnect in this manner see next step 34 Carefully snap in the center console trim cup holder plate to the center console NOTE 2015MY and newer console design Eci 1 is different than pre 2015MY vehicles FX and will may require reconnection of wiring gt 4 gt to center controls if disconnected in step 3 _ N P n a lt 2 j 2014MY and Earlier 2015MY and Later Technical Support 707 544 4761 9 www hurst shifters com x gt 35 To use original shifter handle Bolt in the upper stick assembly on to the Hurst Shifter and torque to 20Nm 15 ft lbs TOOL 18mm socket and torque wrench 36 Carefully snap in the boot bezel on the center console 37 optional Install the Hurst upper stick and Classic Knob A Slide the boot support onto the Hurst stick note some models 2015 may not use boot support and leather boot can be attached directly to the Hurst stick B Install the stick onto the Hurst Shifter using the Supplied washers and screws 30Nm 22 ft lbs C Install the jam nut onto the threads of the Hurst stick TOOL 7 32 hex wrench NOTE The stick should be installed on the right hand side passenger side of the shifter block except on 2015MY and newer mount driver side 38 Disassemble leather boot from stock stick knob boot assembly by prying open the boot clip or disassembly of the shifter knob shaft removing
3. without grease Greasing this area will only attract dirt and contaminants and will not improve performance DO NOT grease lower bushings bushings T X Technical Support 707 544 4761 6 www hurst shifters com 21 Position Hurst Shifter into vehicle and install and Photo taken from underneath vehicle lock front pins NOTE When working from inside the vehicle a small mirror can be helpful to aid in alignment of the front pins Not only are the front bushings very tight on the pins they are also very tight in shifter brackets on the transmission The pins may need to be pried into place _ or pried out for later removal Use care not to damage any of the components if prying is necessary 22 Replace the metal tunnel cover and install the upper shift boot onto cover NOTE Make sure the threads of the rear Hurst Shifter mount come up through the tunnel cover Install the nut finger tight several turns to hold it in place 23 Install the six tunnel cover mounting nuts and torque to 20 Nm 15ft lbs TOOLS torque wrench long extension and 10mm socket 24 Tighten the rear mounting nut and torque to 20 Nm 15 ft lbs TOOLS torque wrench long extension and 13mm socket 25 Install the rubber shift boot cover and the wiring routing ties NOTE Optional step 37 only may be easier to complete see step 37 photo after installing rubber shift boot in this step as better access to the sides of g the shifte
4. Installation Instructions HURST BILLET COMPETITION PLUS SHIFTER 2009 2015 Dodge Challenger Catalog 3916020 WORK SAFELY For maximum safety perform this installation on a clean level surface and with the engine turned off Place blocks or wedges in front of and behind both rear wheels to prevent movement in either direction IMPORTANT This shifter has been primarily designed as a competition and or race shifter As such much of the isolation has been reduced to give the driver the most direct and positive link to the transmission without compromise In doing so this does increase both tactile and sometimes audible levels of vibration While every effort has been made to reduce the amount of objectionable transmission driveline noise transmitted into the interior of the vehicle some vehicles may experience greater amounts than others PARTS a h Nut Knob Stick Shifter Screws 2 Washers 2 Boot Support amp NOTE Washers are designed Tie Wrap for single use only TOOLS e peed dAn O 7mm 8mm 10mm 13mm Socket Wrench amp Hex Wrench Ratchet amp Torque Wrench Long Extension Technical Support 707 544 4761 1 www hurst shifters com TOOLS continued _ Phillips Screwdriver Flat Blade Screwdriver Jack Stands Optional Floor Jack Optional DISASSEMBLY 1 Carefully unsnap the boot bezel from the center console 2009 2014 MY shown NOTE 2015MY vehicles unsnap boot only T
5. ble levels Neoprene isolators 2 ia 4 Washers 2 Screws 2 Technical Support 707 544 4761 11 www hurst shifters com DYNAMAT APPLICATION NOTE Apply even pressure over the entire back foil surfaces of the Dynamat during installation to ensure complete and proper adhesion Trim Dyamat to Size Note Various effective application locations EA 5 EA j Pi f A _ En E y change rod transmission rail connection gt Technical Support 707 544 4761 change rod lower shifter connection 12 www hurst shifters com NEOPRENE ISOLATOR APPLICATION NOTE This step should only be implemented if the above Dynamat application is insufficient to eliminate noise Do not install this if your vehicle will be used in any form of racing and or competitive driving as overall strength and durability as well as shift quality and feel may be diminished with the use of this kit Separate the upper and lower Hurst Shifter stick levers by unscrewing the connecting bolts and then position the supplied neoprene isolators 2 between the upper and lower stick halves and retighten Ensure the bolts will not come loose during repeated hard driving Periodic inspection and verification may be necessary IMPORTANT RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE Technical Service A highly trained technical service department is maintained by Hurst Performance to answer your technical que
6. h bolt and then shifter from vehicle TOOLS ratchet amp 10mm socket NOTE This step may be able to be performed from inside the vehicle however it may be easier to access these components from underneath the vehicle Safely use proper lift points jack stands etc according to the vehicle service manual to help avoid injury if working underneath the vehicle 18 Carefully remove both the upper and lower rubber shifter boots from the assembly Avoid ripping or tearing the boots If they are damaged contact your local Dodge dealer for replacements ASSEMBLY 19 Install the rubber boots onto the Hurst Shifter NOTE A small amount of grease on the openings of the boots can ease installation Position the upper boot flat towards the rear of the shifter vehicle Make sure the upper boot seals fit into Hurst Shifter bracket grooves 1 amp 2 The two front bushings in the front arms of the Hurst Shifter have been purposely designed to have a very tight to snug fit with the lock pins removed in STEP 16 Ensure that these pins can be installed into front shifter bushings prior to attempting install in vehicle Again a small amount of grease can aid with installation 20 Position Hurst Shifter into vehicle and install change rod change rod bolt and torque to 20 Nm 15ft lbs r 2 TOOLS torque wrench amp 10mm socket yy ia Pp NOTE The lower bushings in the Hurst Shifter stick have been specifically designed to operate
7. ha 2015MY and Later 10mm socket as viewed from back seat with front seats at full forward position 9 Raise the center console to access and disconnect the center console storage box lighting connection and any additional wiring connection clips if So equipped 10 Slide reward or remove the center console to gain access to the shifter 11 Remove rear A C duct by lifting at rear to disengage push pin then pulling rear ward Technical Support 707 544 4761 4 www hurst shifters com 12 Remove the wiring routing ties from the rubber shift boot cover and fold cover out of way 13 Unscrew rear mounting nut TOOLS ratchet long extension and 13mm socket 14 Unscrew six tunnel cover mounting nuts TOOLS ratchet long extension and 10mm socket 15 Detach shifter boot from metal tunnel cover and remove cover 16 Unclip and pull out the two front lock pins that hold the shifter bracket to the transmission l NOTE This step may be able to be performed from inside the vehicle however it may be easier to access these components from underneath the vehicle Safely use proper lift points jack stands etc according to the vehicle D _ service manual to help avoid injury if working underneath the vehicle yr Technical Support 707 544 4761 5 www hurst shifters com 17 From inside the vehicle lift up on the shifter assembly to access the lower change rod connection bolt and remove bot
8. he bezel does not unsnap 2 Unbolt the upper stick assembly from the shifter and remove knob boot stick assembly TOOL 1 2 Wrench 3 Carefully unsnap the center console trim cup holder plate from the center console NOTE 2015MY and newer console design 1 is different than pre 2015MY vehicles and will require disconnection of wiring to center controls 2014MY and Earlier 2015MY and Later Technical Support 707 544 4761 2 www hurst shifters com 4 Disconnect the 12V accessory cigarette lighter socket wiring harness connection and small USB connector if so equipped in front of center console opening NOTE The 12V accessory lighter socket is part of the center console on 2015MY and newer models and will not be necessary to disconnect 5 Disconnect the cup holder lighting connection and any other wire harness before finally removing the center console trim cup holder plate if so equipped 6 Remove the two front center console screws both sides TOOL Phillip s screwdriver or 7mm socket 7 Remove the rubber tray in the center console storage box if so equipped Technical Support 707 544 4761 3 www hurst shifters com 8 Remove the screws in the bottom of the center console storage box TOOLS Ratchet long extension 8mm socket NOTE 2015MY and newer center console screws are removed from the side of the console First remove the cover 1 then the bolts 2 wit
9. r and inserting required tools may be easier lf chosen to complete step 37 now complete step 37 and then continue with step 26 immediately afterwards Technical Support 707 544 4761 7 www hurst shifters com 26 Install the rear A C duct 2 Reposition the center console into the vehicle 28 Raise the center console to access and reconnect the center console storage box lighting connection and any additional wiring connection clips if so equipped 29 Re install the screws in the bottom of the center console storage box TOOLS Ratchet long extension 8mm socket NOTE 2015MY and newer center console screws are re installed from the side of the console First replace the bolts with a 10mm 2014MY and Earlier 2015MY and Later socket 2 then the cover 1 as viewed from back seat with front seats at full forward position Technical Support 707 544 4761 8 www hurst shifters com 30 Replace the rubber tray in the center console storage box if so equipped 31 Re install the two front center console screws both sides i TOOL Phillip s screwdriver or 7mm socket 32 Reconnect the cup holder lighting connection under the center console trim cup holder plate and any other wire harness that had been previously disconnected if SO equipped 33 Reconnect the 12V accessory cigarette lighter socket wiring harness connection NOTE The 12V accessory lighter socket is part of the center console on
10. stions provide additional product information and offer various recommendations Technical service calls correspondence and warranty questions should be directed to Hurst Performance Products 707 544 4761 www Hurst Shifters com Technical Support 707 544 4761 13 www HURST SHIFTERS com
Download Pdf Manuals
Related Search