SEAT WITH ADJUSTABLE RIDER BACKREST
Contents
1. push front of seat downward and rearward until tongue engages slot in frame backbone 4 Push seat forward until studs are centered in slots of mounting bracket 5 See Figure 9 Using 5 8 hex install two nuts 4 on studs to secure rear seat mounting bracket to rear fender Alternately tighten nuts to 60 96 in Ibs 6 8 10 9 Nm 6 If installing a new passenger seat refer to the instructions included with the kit If reinstalling stock passenger seat follow the instructions in the Owner s Manual or Service Manual WARNING After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 7 If installing passenger seat install passenger seat strap following the instructions in the Service Manual 8 Install right and left side saddlebags following the instruc tions in the Service Manual 9 Install left side cover on vehicle RIDER BACKREST ADJUSTMENTS 1 See Figure 6 Insert rider backrest Figure 9 Item 6 into opening at rear of front seat and push down until pivot spring locks in place Figure 6 Rider Backrest Pivot Spring J04295 NOTE Adjustments to rider backrest must be done before returning motorcycle to use 2 See Figure 7 Lift Velcro flap at rear of backrest and pull out slider knob to adjust up or down 3 See Figure 8 Turn threaded knob at fr2. sparks can cause a battery explosion which could result in death or serious injury 00049a e Disconnect battery cables negative cable first 2 See Figure 4 Remove battery 2 from battery box 3 Cut two cable straps to free up antenna 3 from frame cross member 4 Carefully remove left side cover from vehicle Set cover aside from work area to prevent damage to paint J04295 is04122 1 Battery cable negative 2 Battery 3 Antenna and cable straps Figure 4 Hands Free Antenna Existing Location 5 See Figure 5 Route security system wiring 1 and hands free antenna 2 over frame cross member to left side of battery box 6 Fasten hands free antenna to left side of frame 3 using two cable straps 1 Security system wiring 2 Antenna and cable straps 3 Frame Figure 5 Hands Free Antenna New Location 7 Install battery into battery box WARNING Connect positive battery cable first If positive cable should contact ground with negative cable connected the resulting sparks can cause a battery explosion which could result in death or serious injury 00068a 8 Connect battery cables positive cable first 2of5 INSTALLATION 1 See Figure 9 Install mounting bracket 1 to rear of front seat 2 using two screws 3 Tighten screws to 60 70 in Ibs 6 8 7 9 Nm 2 Push front seat on frame with mounting bracket at rear 3 Firmly
3. acket backrest adjustment 51869 06 13 Knob threaded adjustment 51868 06 14 Bracket with pivot spring 51876 06 Hardware Service Kit 51666 06 includes Item 8 1 Item 9 2 and Item 11 1 J04295 5 of 5
4. cMOTOR HARLEY DAVIDSON WY J04295 INSTRUCTIONS REV 2006 11 29 SEAT WITH ADJUSTABLE RIDER BACKREST GENERAL Kit Number 51847 06 Models For model fitment information please see the P amp A Retail Cat alog or the Parts and Accessories section of www harley davidson com English only Additional Parts Required WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet references Service Manual information A Service Manual for your model motorcycle is required for this installation and is available from a Harley Davidson dealer Kit Contents See Figure 9 and Table 1 REMOVAL NOTE Refer to Owner s Manual or Service Manual for seat removal instructions for your model FLHR Models Equipped With Separate Rider and Passenger Seats 1 See Figure 1 Remove passenger seat from vehicle If reinstalling stock passenger seat save all mounting hard ware 2 Remove and save the two seat mounting nuts holding the rider seat to the rear fender 3 Carefully remove rider seat from vehicle All Other Touring Models Equipped With 2 Up Seat CAUTION Detach passenger seat strap be
5. fore removing seat Failure to do so can result in damage to rear fender paint 00225a 1 Remove right and left saddlebags according to the instructions in the Service Manual Save saddlebag mounting brackets and hardware J04295 Remove bolt with flat washer on left and right sides to remove passenger seat strap Discard passenger seat strap See Figure 2 Remove existing seat from vehicle See Figure 3 Remove and discard existing nuts from studs on rear fender ee Passenger seat Phillips screw Nut Stud plate Front seat Sh ON Figure 1 FLHR Seat Assembly ee 1 Screw 2 Seat Figure 2 Touring Seat Assembly 2 Up Version 1of5 is04121 1 Stud 2 2 Nut 2 3 Rear fender Figure 3 Rear Fender All Models Except FLHR RELOCATE HANDS FREE SECURITY SYSTEM ANTENNA 2007 LATER ONLY NOTE Proper installation of this kit requires the relocation of the Harley Davidson hands free security system antenna The metal components in the seat will interfere with the signal from the antenna preventing the system from arming IWAN IN To prevent accidental vehicle start up which could cause death or serious injury disconnect battery cables negative cable first before proceeding 00307a WARNING Disconnect negative battery cable first If positive cable should contact ground with negative cable con nected the resulting
6. ont of backrest to adjust forward or backward clockwise forward counter clockwise backward Figure 7 Adjust Rider Backrest Up Down Figure 8 Adjust Rider Backrest Forward Backward MAINTENANCE The adjustable rider backrest can be serviced as follows 1 See Figure 6 Press pivot spring and pull up to remove rider backrest from rear of front seat 2 See Figure 9 Disassemble rider backrest and replace serviceable parts as needed 3 Assemble rider backrest 4 See Figure 5 Insert rider backrest into opening at rear of front seat and push down until pivot spring locks in place 3of5 SERVICE PARTS is04120 Figure 9 Service Parts Seat With Adjustable Rider Backrest Table 1 Service Parts Seat With Adjustable Rider Backrest Item Description Quantity Part Number 1 Bracket seat mounting 51878 06 2 Seat Not Sold Separately 3 Screw hex socket 2 927A 4 Nut seat mounting 3638 5 Cable strap 2 10006 J04295 40f5 Table 1 Service Parts Seat With Adjustable Rider Backrest Item Description Quantity Part Number 6 Adjustable Rider Backrest Kit includes Items 7 through 14 51867 06 7 Rider backrest pad Not Sold Separately 8 Screw button head 2 9492 9 Washer nylon 4 6410 10 Slider with adjustment knob 51871 06 11 Locknut nylon insert 2 7682 12 Br
Download Pdf Manuals
Related Search