Service Manual - Copy Finishing Systems
Contents
1. Feed tray side guides set to width of stock Operator Side guide set all the way to the operators side to ensure staock passes directly under photocell GW 8000 LAYOUT 1 0 General Operation The Model GW 8000 can number on single sheets 12 bond to 12 point card or 45 to 250 gsm paper or multi part carbonless forms up to 10 parts while simultaneously perforating slitting and or scoring With proper set up 8000 sheets per hour 8 5 x 11 stock with one hit can be quickly and identically processed The Model GW 8000 is microprocessor controlled making it easy to set up and program It has the programmability to hold a maximum of 99 jobs with 10 hits and 1 job with 100 hits These jobs can all be stored and recalled for future use The unique friction feeder sends through one set at a time even from the unglued side of a padded set Perforations are done between the register board and main rollers producing a straight perforation slit or score avoiding tail whip Perforating wheels are offered in a wide range of teeth configurations and can be quickly changed using the retaining ring pliers supplied A photocell recognises the lead edge of the sheet and the microprocessor stops the sheet at the specific location s where numbers are required The numbering heads allow for a maximum of four pneumatically driven units Pneumatics allows for non stop tireless operation Finished stock is then delivered to2. 2283 Argentia Road Suite 21 Mississauga Ontario Canada L5N5Z2 Tel 905 858 7663 Fax 905 858 4419 Toll Free 1 800 265 3376 Web Site www graphicwhizard com GW 8000 Reference Shown with optional second head GRAPHIC WHIZARD 2283 Argentia Road Suite 21 Mississauga Ontario L5N 5Z2 Phone 905 858 7663 Fax 905 858 4419 Toll Free 1 800 265 3376 Web Site www graphicwhizard com Version 99 04 2 0 3 0 4 0 5 0 6 0 7 0 GW 8000 Reference Manual Table of Contents General Operation Machine Assembly 2 1 Power Supply Instructions 2 2 Feed amp Exit Trays 2 3 Numbering Heads 2 4 Optional Conveyor Outfeed Plate 25 Additional Switches and Controls Operating Keyboard 3 1 Running a Job 3 2 Stopping a Job 3 3 Changing Programs 3 4 Programming a Job 3 5 The Batch Function 3 6 The Repeat Function 3 7 Motor Speed Control Setting Up a Job 4 1 Aligning the Feed Tray Guides 4 2 Setting Feed Tire Pressure 4 3 Perforating Slitting 4 4 Scoring 4 5 Idler Wheel Holders 4 6 Main Rollers 4 7 Installing Ink Pads 4 8 Locating the Numbering Heads 4 9 Setting Impression Control 4 10 Flatness of Impression 4 11 Stripper Assembly Running a Job 5 1 Setting the Starting Number 5 2 Setting the Repeat Selector 3 3 Fanning Maintenance 6 1 Numbering Heads 6 2 Machine Cleaning 6 3 Lubrication 6 4 Friction Feed Troubleshooting Friction Feeder Print Quality Registration Nu
3. 3 Numbering Heads The height of the numbering head has been factory set and it is critical to the proper performance of the drive unit and numbering head This distance is approximately 3 or the thickness of a numbering wheel change stylus However the numbering head must be levelled to ensure that the numbering wheels strikes the sheet square to provide a quality inked impression and a flat crash impression on carbonless sets This will be discussed later Section 4 11 The numbering heads can operate through 360E This is done by loosening the numbering head rotation screw using the large hexdriver supplied located on the front of the numbering head mount block Once the screw is loose the head is free to rotate Tighten the screw once the desired position is achieved in order to prevent any movement during machine operation The standard numbering head is 7 16 4 5mm Gothic style reverse order 6 digits with 2 drop wheels The numbering head employs a pre inked pad which can be purchased in red or black These inkpads will supply you with approximately 15 000 impressions Uninked pads may be purchased if a different colour is required Note any ink used must be a non metal corrosive one labelled numbering machine ink Page 5 The numbering head comes standard with six numbering wheels a seventh numbering wheel is optional the last two of which are drop wheels this will be discussed later The first 5 digits may be activa
4. 6 8 and 12 teeth per inch as well as Microperf The blades can be easily Blade Hub interchanged using the Either Blade OR Idler Tire Fit Va T T a 3 4 Snap Ring Figure 8 Accessory Holder ring pliers supplied with the machine Remove the accessory holder see Figure 8 from the machine Simply remove the retaining clip from the blade hub and pop off the blade Place the new blade on the blade hub and put the retaining clip back on Ensure that the retaining clip sits completely in the groove in the blade hub in order to prevent any movement of the blade Using the small hexdriver move the bottom boss wheel to the approximate eat weal jie Ones o T location of the desired C Pig perforation or slit Note E SEER Keep all of the setscrews of Regular Score Blade pa In This Groove the boss wheels in line on the shaft Move the accessory Figure 9 Blade Placement on the Boss Wheel holder to the position desired where the perf slit blade will ride on the flat surface of the boss wheel see Figure 9 and tighten the position locking set screw into the keyway of the square shaft using the large hexdriver Since you can control the depth of a perf slit it is critical that you locate your perf slit wheel to the flat of the boss wheel Tighten the pressure adjustment screw located on the top of the accessory holder and turn the handwheel at the same time When the perf slit blade turns with the handwhee
5. inkpad to compress the felt You can then soak up the excess ink with the pad Once the pad is conditioned you gently squeeze the plastic fingers inwards on the back of the ink pad holder and slide it into the groove on the ink pad holder plate with the ink reservoir side of the pad sliding in first Release the tabs and the holder 4 8 Locating the Numbering Heads To move the drive unit into the lateral position required loosen the large star shaped knob near the bottom of the drive unit mount block refer to Figure 3 Loosen the setscrew in the anti pitch block using the large hexdriver This will allow you to slide the drive unit across the width of the machine You may now move the drive unit to the location desired Bring the anti pitch block over to and against the drive unit Now tighten the large star shaped knob and set screw in the anti pitch block to lock the drive unit in place The anti pitch block and drive unit mount block act together when locating a number position If the number position is slightly off you can loosen one of the blocks and move it over the appropriate distance using the fastened block as a reference point Also when going to replace the inkpad you may move the drive unit aside leaving the anti pitch block in position as a reference when you wish to continue the job Page 20 To turn the numbering head so that it prints the number in the correct rotation first loosen the rotation lock screw on the numbe
6. removed and stored elsewhere when not in use Place the tray side guides bottom flange towards the centre and i g Tray Assembly the centre slot cover on the tray as shown in Figure la and Figure 1a screw on the nylon wing nuts to secure the pieces on the tray The operator side tray guide of both the feed and exit tray should be pulled all the way over to the Feed Rollers Magnetic Backstops mounted inside Tray Exit Rollers Side Guides to receive finished stock Feed Tray Mounting Exit Tray Mounting Figure 1b Figure 1c operator side before tightening its two wing nuts Note It is critical that the operator side tray guide be moved all the way over to the operator side of the machine to ensure that the stock being processed through the machine passes directly underneath the photocell If the stock does not pass directly underneath the photocell the machines will not recognise sheets and the program being run will not be initiated Place a pile of the stock to be processed in the feed tray and use it to align the non operator side tray guide to the pile Allow a fraction of an inch so that the pile flows freely up and down the tray if released from the top Set the exit tray in a similar manner although the accuracy of the non operator side guide position is not critical As a backstop to finished stock there are two magnets included with the machine unless equipped with the conveyor outfeed that are set inside the s
7. side to side impression ie if the impression is too light or too heavy across the machine determine in which direction the numbering head must pivot to flatten the crash consult Figure 9a which is viewed from the non operator side of the machine For adjustment 1 to pitch the numbering head away from the non operator side loosen the top hand knob on the drive unit mount block and turn the left right pitch screw counter clockwise Similarly turn the left right pitch screw clockwise for adjustment 2 To adjust for an uneven top to bottom impression determine in which direction the numbering head must pivot to flatten the crash consult Figure 9b Adjustments for forward backward pitch are made by first loosening the bottom hand knob on the drive unit mount block and turning the forward back pitch screw in the appropriate direction After adjusting number another carbonless set and make necessary adjustments until the numbering head creates an equal impression along the whole number 4 11 Stripper Assemblies Each machine is supplied with a minimum of 3 stripper assemblies Their purpose is to keep the stock flat as it runs through the machine and to ensure that the stock does not catch on the numbering head The stripper blocks are to be mounted on the keyed square shaft pointing down the same shaft that the accessory holders are mounted on They should normally be located close to the numbering head but not underneath the numberin
8. CLR if you wish to clear a quantity entered to disengage the batch function Once again the ESC key will return you back to the main operating menu without activating the batch function Pressing F1 will reset the paper count and batch quantity When running a job with the batch function the machine will stop after the last sheet has been processed leaving the sheet partially in the exit rollers allowing you to insert a slipsheet The LCD display will then show the number of batches completed Page 13 FUNCTION 1 Displays the number of batches that have been completed of Batch Size DISPLAY PERF SHIELD RED PHOTOCELL GRN IMPRESSION 1 S ON PERF SHIELD OPEN ON NO PAPER NO FUNCTION IMPRESSIO NO FUNCTION DISPLAY FUNCTIONS DISPLAY XXXXX batch quantity EXIT exit to Mode Idle CLR clear batch quantity This screen will show you how many batches you have completed Multiply the BATCH QTY by the BATCH SIZE and you have the total quantity of your run When the machine stops after each batch has been completed you may insert a slip sheet in the exit tray and simply press the START button to continue with the next set 3 6 The Repeat Function The repeat function key REP is a future feature for the GW 12000 Currently the repeat selector on the numbering head is used to obtain a repeat ability as discussed in Section 2 2 3 7 Motor Speed Control The motor speed ca
9. Exit to Mode Idle MOTOR EMERGENCY STOP Exit to Mode Idle 3 2 Stopping a Job Here are methods of stopping the machine 1 Once the program is running there are several built in safety emergency stops Pressing the STOP button any of the digits 0 9 F1 STOP ACC ESC REP and if the Batch size is 0 BAT will cause the machine to finish the stock it is currently working on move the next stock into the starting position and then stop the motor This automatically sends you into Idle Mode 2 If you want to stop the machine while stock is still left in it simply hold on to the stock in the feed tray After about one second the machine will automatically stop since it is no longer seeing any new sheets This is how it also stops when all of the stock in the feed tray is gone 3 3 Changing Programs The GW 12000 allows you several choices in programming PROGRAM 00 Perf score automatically turns the numbering heads off PROGRAM 01 99 Allows for a maximum of 10 hits per head PROGRAM 100 Allows for a maximum of 100 hits per head Whenever you wish to change programs the LCD display must be in Idle Mode Section 3 1 press the SET UP button The following screen will appear DISPLAY PERF SHIELD RED PHOTOCELL GRN IMPRESSION 1 OQ ON PERF SHIELD OPEN ON NO PAPER I seser NO FUNCTION west E EE E ai Ea E Once you select the program number desired you may either RUN the exist
10. a exit tray Page 2 2 0 Machine Assembly Remove and unpack all machine parts from the shipping carton 2 1 Power Supply Instructions Before connecting the power cord to a wall receptacle make certain the supply voltage is what the machine has been set up for The voltage is marked on the sticker containing the serial number of the machine If there is any discrepancies please call your dealer first before plugging in the machine The switch module is located behind the main operator side panel directly underneath the register board It also houses the main fuse CHANGING THE FUSE IN THE SWITCH MODULE SCREWDRIVER FUSES FUSE S HOLDER y D ON OFF Laf SWITCH CORD RECEPTACLE Lo m _ J INSERT THE FUSE HOLDER J BACK INTO THE UNIT FRAME INSERT TWO SLOW BLOW WITH THE 115V SHOWING FUSES RATED 250V 5A FOR THROUGH THE WINDOW A SUPPLY VOLTAGE OF 120V THESE FUSES ARE 1 4 INCH WIDE BY 1 1 4 INCHES LONG Lal LIP INSERT SCREWDRIVER INTO LIP OF THE FUSE FRAME OPEN THE FUSE FRAME DOOR AND PULLOUT THE RED FUSE HOLDER Page 3 2 2 Feed and Exit Trays The feed and exit tray assemblies are comprised of four components each the tray two tray side guides and a centre slot cover see_Figure la SIDE GUIDE CENTER SLOT GUIDE The trays sit in the machine on mounting pins inside the machine s side frames as shown in Figure 1b and Ic The trays can be easily
11. ack under it Release the new stack into the feed tray letting it slide down under the feeding stack Lower and release the back edge of the bottom set so that the stacks now sit together This back feeding procedure should be done while there is still sufficient stock in the feed tray to allow for the time needed to prepare and insert the new stack Figure 11 Feeding Stock Page 26 6 0 Maintenance The GW 8000 is designed to be trouble free through years of use Only minor maintenance operations are required to keep it running like new 6 1 Numbering Heads With use the numbering heads will acquire a coat of old ink paper dust etc and therefore periodic cleaning is necessary The minimum frequency of numbering head cleaning is once a month or when changing over colors Detach the numbering head by removing the two setscrews on the numbering head mount block using the larger hexdriver provided see Figure 12 The head may then be cleaned with a petroleum based NumberngHeadl spray lubricant such as WD 40 or Sprayaway RD 90 and a small brush ie an old toothbrush Spray and soak the number wheels thoroughly Take care to keep the spray away from the rest of the machine Brush the wheels and then rotate them in order to clean every digit Spray the numbering wheels a final time to rinse out the ink or dust After Figure 12 Removing the Numbering Head cleaning allow the head to dry completely ie leave it standing overn
12. are situated beside the display A numeric keypad an ESC escape ACC accept START and STOP button rounds out the rest of the keyboard The ESC button can be used at almost any time except during actual running in order to return to the previously viewed menu The functions of the rest of the buttons will be discussed later in this section Once you have plugged the machine in turn the on off switch to the on position The microprocessor does an internal system check and the above will flash on the screen Page 7 3 1 Running a Job The Idle Mode is displayed below From this menu you can change the motor speed modify your paper count and select your program In this menu you can also enter the Batch size see 3 5 DISPLAY PERF SHIELD RED PHOTOCELL GRN ON PERF SHIELD OPEN ON NO PAPER IMPRESSION 1 DISPLAY FUNCTIONS DISPLAY ssssss motor speed bar graph PGMxxx solenoid program in RAM ccccce paper count 4 decrement motor speed increment motor speed 1 decrement paper count aaa CLR gt clear paper count normally aaa BAT gt Enter Mode Set Batch Size when batch mode is enabled The lt lt lt gt gt gt will adjust the motor speed F1 will decrement the paper count F2 will clear the paper count but if it is already at 0 it will send you to the Batch mode Section 3 5 SETUP will select a program Section 3 3 and START will begin the job Y
13. blade and boss wheel lined up you can adjust the depth of the score and run some test sheets adjusting the depth of the score until you are satisfied Making adjustments for a straight score are done in the same manner as a perf slit as discussed in Section 4 3 4 5 Idler Wheel Holders On the same keyed shaft that the accessory holders are mounted on for your perf score slit operation there are two idler wheel holders These holders if possible should be mounted about to 12 from the outside edges of the stock being run As the stock leaves the feed tires it will then be perfed scored or slit The idler wheel holders purpose is to equalize the force along the stock as it passes through this section so you do not encounter any skew which you may encounter if you only had a perf score slit wheel contacting the paper before going through the main rollers 4 6 Main Rollers The main rollers are comprised of a bottom solid roller and 6 adjustable rollers on top The top rollers are mounted on a spring loaded shaft to maintain pressure down to the bottom solid roller The adjustable top rollers must be distributed along the shaft so that there is a roller on each end of the shaft with the remainder distributed along the shaft To ensure proper transport a majority of the rollers should be on the stock but do not load all rollers to one end of the shaft where you may encounter stock skew Page 19 4 7 Installing Ink Pads Loosen the
14. cter displayed when hit programmed C1 solenoid channel 1 head 1 3 solenoid channel head 2 SOL3 C2 solenoid channel 2 head 1 4 solenoid channel 2 head 2 SOL4 The sheet you inserted is automatically moved to position 75 Position 0 is the lead edge of the sheet passing the photocell Position 75 is the first location that an entire number will print on the paper Note Each step represents approximately soth of an inch The first two function keys step the paper either forward or backward Note you cannot back the sheet back further than position 75 The other two function keys fire either head 1 or head 2 Once a head fire button has been pressed the numbering head will fire and the LCD display will light up with one solid bar around the corresponding head fired eg MC1 In a four head system heads 1 amp 3 work together and heads 2 amp 4 respectively To activate heads 1 amp 3 at any position press F1 head 1 will fire and C1 will appear on the display press 3 on the keypad and head 3 will fire and C13 will appear To activate head 2 amp 4 you must press the number 4 on the keypad and C24 will appear on your display Configured we can have in any one program with a four head machine a combination of at any one time heads 1 amp 2 amp 3 amp 4 1 amp 3 2 amp 4 1 2 Heads 3 amp 4 cannot activate on their own If the number is not in the position desired simply press the function b
15. e stock such as sheet curl and inconsistent glue thickness on multiple padded forms Improper setting of the feed tires can cause random skewing problems Warning All feed and exit tires and perf score slit boss wheels use setscrews to secure their positions When tightening setscrews do not over tighten them This may scar the metal shafts and inhibit the free sliding movement of the feed tire hubs or perf score slit boss wheels To ensure consistent trouble free feeding the feed tire pressures must be set as loose as possible The feed tires should never contact the retarder strip Our design allows for no double feeding with substantially reduced feed pressure than the typical friction feed system The gap between the feed tires and the feed platen should be just less than the thickness of the stock being used Remember FEED TIRE PRESSURE L ADJUSTMENT SCREW that we are retarding the full lead edge of the next LOCKING I SECOND SHEET IS RETARDED sheet or set When eel FIRST SHEET SLIDES setting the feed tire ff SMOOTHLY THROUGH pressures you should Sanwa Oy have the sense that the feed tires are just FEED PLATEN touching the paper It is better to set the feed tire Figure 7 Feed Pressure Adjustment pressure to the minimum pressure required to prevent double feeding The remedy to correct double feeding is to turn down the both feed tire pressure adjusting screws a yth turn until consistent
16. ear or harden Use a rubber roller reyjuvenator occasionally to soften the rubber Other than the feed tires another important element of the friction feed system is the full lead edge retarding strip The abrasive agent on the retarding strip prevents sheets from double feeding As the abrasive agent wears you will encounter more double feeds and when you see the green backing of the retarding strip you must replace it To replace the retarding strip for the feed adjust the feed shaft to its highest position Using a scribe or sharp edge etch into the feed platen where the retarding strip ends you will use this scribed mark as a reference point when you apply the new retarding strip Peel off the old retarding strip you may need a knife or razor and remove any old adhesive with alcohol Replace with a new self adhesive retarding strip Make sure that there is some of the retarding strip surface under the feed tires to ensure proper operation 28 7 0 TROUBLESHOOTING SYMPTOM Friction Feeder Double Feeding Creasing marking or sets pulled apart Kicking turning Not feeding paper Print Quality Uneven crash impression Faint colour or uneven colour impression Excessive inking Too heavy embossing or too light a crash Ink spreading smudging or not drying SOLUTION Adjust feed tires down by an y turn feed is too loose if the retarding strip is glazed or worn you can see the green backing replace retardi
17. eeding place a piece of stock in the feed tray and align the lead edge with a straight edge within the machine such as the straight edge of the feed platen or the edge of the first shaft in the machine Now check that the operator side feed tray guide is parallel to the close edge of the paper for squareness 4 2 Setting Feed Tire Pressure The friction feed system used in automatic Graphic Whizard machines is unique It utilizes three top feed tires to feed sheets through with a consistent pull along the full lead edge of the sheet and a continuous width sheet retarder the strip of fine sandpaper on the feed platen to separate sheets and prevent double feeding Once the feed tray and side tray guides have been assembled according to the sheet width required you may locate the feed tires along the feed shaft For proper sheet feeding the position of the three feed tires along the width of the sheet is also important Loosen the set screws of the feed tire hubs using the small hexdriver provided in the accessory kit Slide the feed tire hubs along the feed shaft setting the two outer tires at about 12 in from the outside edges of the stock The third middle feed tire is simply centred Keep the three setscrews of the feed tire hubs in line on the feed shaft Tighten all setscrews see GW 8000 Layout on Page 2 Page 15 If a feed tire is set too close to the edge of the sheet its feeding efficiency will be affected by variances in th
18. epend on the type of job required The repeat selectors is clearly in view on the front of the numbering head and requires no special tools to be changed see Figure 4 Remember for 2x 3x and 4x repeat action you may need to run a couple of test sheets to ensure these actions match your numbering sequence since the numbering head is a mechanical process separate from the number position programming If the repeat sequence does not match the numbering sequence on your stock you may need to manually engage the numbering head Push down on the numbering wheel frame as many times as it takes to complete the repeat action counting where the sequence was on your last test sheet Example Repeat action desired is a three time action After running a test sheet 9 9 8 is printed The numbering head is in mid sequence and to correct push down on the numbering wheel frame twice to complete the repeat action Test another sheet and the sequence printed now is 7 7 7 5 3 Fanning The final feeding concern is the fanning of the stock This procedure may also take some practice and in particular when fanning carbonless sets across the un glued edge The following steps should be used in order to fan the pile Figure 10 Fanning Stock for Feeding 1 hold the paper as shown in Figure 10 2 lower your left hand while holding on to the pile firmly with your right 3 hold the pile tight with your left hand and l
19. f it does not line up again check that the perforation itself is straight If not check the main rollers for equal distribution over the sheet and also check that the feed tires have equal pressure Page 18 along the sheet The feed pressure adjustment screws dictate the paper travel The general rule to remember is that a perforation runs away from a tighter tire If the perforation runs towards the non operator side then loosen the operator screw by an yth of a turn and tighten the non operator side by an yth of a turn Vice versa for a perforation that skews towards the operator side Make adjustment to the exit rollers in the same way you make adjustments to the main rollers if the perf starts straight and then tails off If the perforation is straight but the perforation does not line up you may still not be feeding the sheet through square Whether perforating or slitting place one of the strippers close to the cut The new cut in the sheet can often cause the sheet to curl up and can cause a jam otherwise 4 4 Scoring Setting up a score is similar to perforating or slitting although the scoring blade will run in the groove of the bottom boss wheel With a score it is more critical to control the depth of the blade because this controls the depth of your score When lining up the blade and groove of the boss wheel do not tighten the boss wheel until you have run the score blade into the groove using the handwheel Once you have the
20. feeding is achieved If the feed tire pressure is too much you will possibly mark or pull apart forms Adjustments for feed tire pressure are made with the feed tire pressure adjusting screws see Figure 7 It is recommended to place two sheets of the stock in the feed tray with the feed tire pressure set loosely Hold the two sheets in your hand with one sheet ahead of the other Place the leading edge of the first sheet under the feed tires Slowly tighten the feed tire pressure adjusting screws while jiggling the pages back and forth The correct setting is achieved when the second page is no longer able to run under the feed tires All three feed tires should be adjusted to the same pressure setting to minimize skewing To check that all the feed tires are adjusted to the same pressure tear a strip off the stock being run and pass it under each feed tire Page 16 separately You should sense the same amount of drag under each feed tire A tighter feed tire pressure on one side of the sheet will cause faster feeding of that side of the sheet the sheet will skew or twist towards the feed tire with tighter pressure To prevent this skewing reduce pressure on the side of the feed tire shaft where you encounter more drag with a counter clockwise yth of the feed tire pressure adjusting screw and increase pressure on the other side by a clockwise yth of that feed tire pressure adjusting screw These adjustments should cause a chan
21. g wheels this can damage the numbering wheels or close to where a perf score slit is being performed igure 9b Up Down Adjustment If you experience double images when numbering it is possible that the stripper pressure is not enough to keep the stock flat for the crash and the stock is bouncing allowing a second image to occur If this occurs simply bend the strippers down to create more pressure on the paper Page 23 5 0 RUNNING A JOB 5 1 Setting the Starting Number In order to set the starting number on the numbering head you will have to pivot the drive unit back to get clear access to the numbering wheels Pull down the numbering wheel frame and push in the locking tab to engage and lock the numbering head with the numbering wheels exposed Each individual numbering wheel can be rotated to the appropriate starting number using the change stick provided in the accessory kit Remember that the standard head counts backwards so the number that you set to start the job on will be the last number required If you do not require all the digits to print ie 0097 is desired instead of 000097 the last two numbering wheels can be dropped from profile and locked down To do this rotate the numbering wheel to the 9 position Turn the wheel slightly past this position while also pushing down on the 9 When the correct position is reached the 9 will drop below type height To restore a dropped wheel to its regular print pos
22. ge in the overall balance of pressure from the three feed tires without affecting the total feed tire pressure When you have the feed tire pressure set properly you can then tighten down the white nylon thumbnuts to ensure the setting will be maintained Note The only time the feed is too loose is if double feeding occurs which the machine will detect and the message PAPER TOO LONG will appear on the LCD display If the feed is too tight the feed tires will try to pull only the top sheet off a set If this occurs loosen the feed tire pressure a little on both feed tire pressure adjusting screws evenly until this no longer happens With the GW 8000 carbonless sets feed best from a non glued edge Glue thickens the set and can cause waves on the edge while the unglued edges tend to be more consistently flat Advisory It may require several attempts to get used to this sheet feed technique and it is recommended that you practice a few numbering jobs with scrap paper However some initial trial and error experimentation will allow you to develop long term benefits in efficiency 4 4 Perforating Slitting Perforating slitting and or scoring can be performed with or without any numbering As previously mentioned if no Pressure Adjustment Screw Locking Thumbayt Position Locking Set Screw Snap Rings i P i numbering is desired program 00 has been set aside for this task The perforator blades are available with 2 4
23. ide tray guides on the exit tray Relative position of the magnets depends on the stock being processed but the magnets should be set such that the stock does not slide down the exit tray too far possibly causing sheets to get in uncollated order Page 4 2 3 Numbering Heads The numbering heads are already secured to the drive unit by two screws through the numbering head mount block as shown in Hand Kon Figure 3 The drive unit is then mounted to the drive unit mount block using the f Pien Seram hand knob provided While installing the drive unit make sure the screw cap on Mount Blaak the back of the drive unit fits Kamberi Head in the cavity on the drive unit G Anti Pitch Block mount block so that the rubber plug provides some i change Sis Numbering Head should be approx 1 4 Drive Unit Mount Block Left Right Pitch Screw Hand Knob Forward Back Pltch Drive Unit Mount Shaft from the platen or the pressure against the screw VA rouse ora ranas aia cap To do this you may Paton have to back out the left right pitch screw Plug in the cord from the drive unit into the appropriate receptacle on the non operator side cover closest head to the closest receptacle If your machine is equipped with more than one head by convention the numbering head and drive unit closest to the operator control panel will be referred to as head 1 H1 and the other will be head 2 H2 Figure
24. ight or blow it dry with compressed air Wipe the head and reinstall Drive Unit Remove Set Scregis Numbering Head Important Do not use solvents Solvents will strip out the lubricants from the head allow corrosion and impair the correct functioning of the print head 6 2 Machine Cleaning After each job or midway through a very large job clean the feed tires You can use warm water to clean off paper dust or drying powder or blanket wash or alcohol if there is ink on the feed tires Any type of rubber roller rejuvenator is also good to clean the feed tires the rejuvinator will also soften the rubber This will prevent glazing of the rubber Brand new tires will require extra cleaning for the first job or two until the rubber beds in Page 27 In addition always watch that paper dust or dirt does not block the two photocell sensor eyes The green light on the control panel marked PHOTOCELL can verify correct photocell operation If dirty simply wipe the photocell sensor eyes but do not use solvents Either use a cotton swab or blow clean with compressed air Ensure that the trays and guides are clean 6 3 Lubrication The Model HS utilizes ten oil impregnated bronze bushings to support all shafts An occasional drop of light machine oil will maintain their lubricating qualities Wipe off any excess oil to avoid spoiling a job 6 4 Friction Feed Over time the rubber components of the feed tires may w
25. ing program or EDIT it by pressing the corresponding function key F1 to RUN amp F2 to EDIT If RUN is selected the machine will to exit to Idle Mode where you press START The ESC key will also return to Idle Mode in case you wish to change the counter before beginning a job Page 10 3 4 Programming a Job If you wish to program a job EDIT an existing program press F2 After selecting EDIT if the program already exists the machine will ask whether you would like to erase it start new NEW or modify it MOD DISPLAY PERF SHIELD RED PHOTOCELL GRN IMPRESSION 1 SO ON PERF SHIELD OPEN ON NO PAPER o o A ee ace START This selection is done with the corresponding function key lt lt lt and gt gt gt respectively When modifying a program previously programmed hits can be removed from the program while additional hits may be added Once you make your selection the machine will instruct you to INSERT PAPER PRESS START The LCD display will then show the following DISPLAY PERF SHIELD RED PHOTOCELL GRN IMPRESSION 1 OQ ON PERF SHIELD OPEN ON NO PAPER NO FUNCTION IMPRESSIO NO FUNCTION DISPLAY FUNCTIONS DISPLAY xxx solenoid program number cecce current paper position in motor steps from paper lead edge lt lt lt motor moves in forward direction gt gt gt motor moves in backward direction Page 11 full block chara
26. ition simply rotate the wheel in the regular direction and it will pop out of its sunken position and back into regular print position Once your number has been set and the inkpad has been installed see Section 4 7 set the repeat selector to 0 Now pull the numbering wheel frame downward to release the locking tab Gently release the numbering wheel frame and allow it to return to its rest position Caution the numbering wheel frame is spring loaded Once you release the locking tab the numbering wheel frame will spring back quickly Please make sure that you keep your fingers clear of the inner workings of the numbering head If you pull the numbering wheel frame down too far and it locks refer to Section 4 4 If you do not return the numbering wheel frame to its rest position the numbering head will not operate when the machine is running since it is already at the end of its available stroke length Now you can pivot the drive unit back to the print position and re tighten the large knob It is advised to set the repeat selector to 0 while running a few test sheets so that the starting number does not change When you are ready to start your numbering job then change the repeat selector to the action desired Page 24 5 2 Setting the Repeat Selector The numbering heads can be set to repeat a number continuously 0 change with every crash 1 or change after a number of crashes ie 2 3 or 4 This setting will d
27. ken What you want to achieve is an even level impression with minimal or no embossing of the stock Page 21 IN ITS NORMAL POSITION THE RED LOCKING TAB WILL BE PUSHED OUT REGULATOR INSTRUCTIONS INSTALLING HOSE a WHEN INSERTING INSERT THE HOSE PULL UP ON HOSE PUSH DOWN PUSHING IT DOWN JUST THE HOSE ON THE RED TAB AS FAR AS IT WILL TO LOCK IT IN GO PLACE REMOVING HOSE ya PUSH DOWN ON HOLD RED TAB HOSE UNTILL DOWN WHILE RED TAB IS DOWN PULLING UP ALL THE WAY ON THE HOSE With the GW 8000 the numbering heads are pneumatically driven The air pressure is regulated from the air source whether shop air or a stand alone compressor on the machine at the regulator gauge manifold assembly The optimum pressure setting at the regulator is 45 60 psi If numbering a job with many numbers you may need to increase the Impression Control to maintain a consistent impression or increase the air pressure at the regulator by 5 psi 4 10 Flatness of Impression It is best to check for the flatness of the impression on the bottom crash copy from a carbonless set The inked impression will not adequately show whether the impression is truly flat while the bottom crash impression shows this quite well Make some test impressions on carbonless verify the flatness of the crash impression and follow the proceeding instructions Page 22 Ce 123 2 456 Figure 9a Side Adjustment To adjust for an uneven
28. l test a few sheets Continue to make adjustments until the desired perforation depth is obtained To ensure a straight perforation score or slit run a few sheets through the machine Using a straight edge check if the perforation line is straight If not you may not have the main tires placed evenly across the sheet with one tire on the non operator side Next flip the first inch of the lead edge of the sheet over and check to see if the perforation lines up If it doesn t double check that there is no excess play in the tray side guides and that the operator side tray guide of the feed tray is over to the operator side as much as possible You may not be feeding the sheet into the machine square To ensure that the sheet is running through the machine square you can feed a sheet into the machine using the handwheel and align the lead edge of the sheet with a straight edge in the machine such as the edge of the bottom boss shaft To adjust the squareness of feed you can move the front or back of the operator side tray guide on the feed tray to make sure the sheet travels through the machine square If you adjust the operator side tray guide you must adjust the non operator side tray guide as well Run a few more sheets through and check the sheet again Continue until the perforation lines up Now take the lead edge of the sheet and fold it over to the last inch of the sheet Again you are checking to see that the perforation lines up I
29. large star shaped lower knob on the drive unit mount block and swivel the drive unit up This will allow you better access to the numbering head itself Slide the repeat selector on the numbering head over to the 0 position see Figure 4 if you are unfamiliar with the components of the numbering head Pull down the numbering wheel frame the ink pad mount plate swings away giving you better access to the ink pad and exposes the numbering wheels Now press in the locking tab which sticks out from the top of the head frame When you pull the numbering wheel frame down far enough the locking tab will drop into a groove on the numbering head shaft and hold the head in this position If you pull the numbering wheel frame too far down the repeat selector may jam the head Simply pull the numbering wheel frame further down and press the repeat selector out of the way Remove an inkpad from its package provided in the accessory kit and grasp the two plastic fingers on the back of the ink pad holder Before inserting the inkpad you must first condition the pad Because the pad is felt it may have swollen with ink and be thicker than need be If inserted on the numbering head an inkpad with a swollen felt can cause the number wheels to get too much ink and create splattering or fat images To condition the inkpad use a piece of coated stock because it is less absorbent and place the inkpad on the coated stock felt side down Press down hard on the
30. mbering Heads Page DNDN WOW Strippers are to be placed close to where a numbering head is located or close to an accessory holder when pertiscoresittng to hold down the stock at that postion The strippers help to guide the stock through the machine Make sure the strippers do NOT interfer with tires or the numbering wheel Exit tires like the main tires should be placed so that one is on each end of the shaft land the 2 remaining spread out across the shaft Make sure an exit tire does not follow Tires on the main shaft should be placed la numbering head you may track ink down the rest of the stock as it exits with one on each end of the shaft and the majority Used to transport the stock we Exit tray guides are spaced to catch the finished stock but do not to be as tight as the feed tray guides A Idler tires are set so that they just Magnets are placed in the guides nN turn as the machine is in operation to act as a backstop for the stock a Position of the idler tires should be as it exits the machine 4 to the outside edges of the stoci x i 7 Numbering Heads can be positioned along the shaft C and numbering positions are then programmed Fo ach job the numbering heads should be levelled for the best impression 1 y Outside feed tires set in 1 1 2 from edges of stock Exit strippers help to direct the finished stock into the exit tray especially lighter stocks that may curl 4
31. n be changed while the machine is running or idle This function is performed by using the first two function keys under the LCD display screen marked lt lt and gt gt when you are in the main operating menu The bottom line of the LCD display shows a down arrow to slow down the motor and an up arrow to speed it up Maximum throughput speed is 8 000 sheets per hour 11 x 82 or A4 with one number per page Page 14 4 0 Setting Up a Job To set up the machine for a specific job a few items must be adjusted depending on the specific stock being run the number of heads being used and the number of perforations slits or scores required In order to keep it simple adjustments required will be discussed from the feed end of the machine to the exit 4 1 Aligning the Feed Tray Guides As previously mentioned the operator side tray guide should be seated all the way to the operator side This will ensure that the stock passes directly underneath the photocell allowing the program being run to initiate With a pile of the stock placed in the tray align the non operator side tray guide with the pile Allow a fraction of an inch so that the pile flows freely down the tray if released from the top Move the centre slot cover so that it is in the middle of the two side tray guides and tighten the wing nuts It is very important that the stock enters the machine square to ensure that all perfs are square and straight To test for square f
32. ng strip see Section 6 4 Adjust feed tires up by an y turn feed is too tight Balance adjustment on feed shaft required one side is too tight adjust feed tray guides closer together to eliminate side to side play see Section 4 1 amp 4 2 for adjustment instructions Feed may be too lose in which case multiple sheets are jammed under the feed tires check adjustment if feed tires are smooth or glazed clean rejuvenate or replace open feed tray guides set too tight to paper width and pinching stock Adjust for crash flatness see Section 4 11 Replace ink pad see Section 4 7 Clean head see Section 6 1 condition ink pad see Section 4 7 or replace leaking ink pad Adjust Impression Control dial see Section 4 10 check platen pad if there is excessive wear the platen pad may require replacing Numbering machine ink is mineral oil with pigment The oil is absorbed by the paper leaving the pigment behind as the image On slick or glossy stocks the supplied inkpad will not work effectively A non corrosive ink must be used as a substitute such as fountain pen ink An important factor with alternative inks is that the 29 numbering heads be cleaned immediately after a job has been run Registration Inconsistent number Check that the photocell is clear of any obstacles see location poor number Section 6 2 if the number location seems to float register the feed tray guides may be too loose allo
33. once again come into contact with the numbering wheel flats Depending upon the action or sequence in place the repeat pawl may only interact with one of the repeat action ratchet wheels before the changeover pawls interact with the numbering wheel flats In most instances the longest changeover pawl comes into contact with the flat of the unit wheel flat to change it over After a 0 has been printed there will be more changeover pawls changing more numbering wheels When this happens you may find the next impression with a 9 as the last digit printing lightly This can be overcome by increasing the Impression Control to provide a stronger pulse to turn over more wheels If you are encountering problems where numbers are not turning over numbers are printed out of sequence etc then the problem may be that the changeover pawls of the repeat selector are not aligned with the flats of the numbering wheels The repeat selector is mounted on the print head frame by the two repeat selector adjustment screws The repeat selector must be mounted to the print head frame squarely If not the changeover pawls will not engage the flats of the numbering wheels square in this case some of the changeover pawls can not change their numbering wheels Visually check that the changeover pawls are riding in between the numbering wheels centred on their flats If not the whole repeat selector may be moved to the proper position by loosening the repeat select
34. oosely with the right 4 return the left hand to its original position Page 25 5 repeat steps 1 through 4 until adequate fanning is obtained Try fanning while holding the stack in a vertical upright position with the glued edge resting on a table This will maintain a flat straight edge When loading a fanned stack into the feed tires hold the back end of the stack up high at approximately a 30 degree angle relative to the feed tray so that the lead edge slips under the feed tires see Figure 11 Then gently lower the stack onto the feed tray Before starting the machine rotate the handwheel one half turn and watch that the first sheet of the stack advances correctly while the second sheet beneath it should be retarded from feeding into the machine The efficiency of the feeding can be improved by SG cis increasing the spacing Fannod Stock Ne between the sheets of your fanned stack Begin with y small stacks 10 to 20 sheets and build up to larger stacks as you become more confident with your fanning Feed Roller Once you have mastered the art of fanning you can progress to back feeding to provide continuous feeding and uninterrupted operation To feed while the unit is operating fan a stack and while holding it in your right hand carefully grasp the bottom set of the feeding stack with your left hand Raise the back edge of this bottom set thus slightly raising the back of the feeding stack and slide the new st
35. op for the finished stock 2 5 Additional Switches and Controls The main on off switch is located under the feed tray beside the main fuseholder and power cord On the left hand side of the operating keyboard there are two potentiometer knobs that control the crash strength of the numbering head known as Impression Controls and can be adjusted to best suit the requirements of the job For example you may require stronger crash numbering for carbonless sets than for single sheet bond paper This adjustment can be done while the machine is stopped or running Page 6 3 0 Operating Keyboard IMPRESSION 1 S FLASHES IF RAM ERROR FLASHES IF LCD ERROR LF serur srant FEET ogag NO FUNCTION wP E aio S E Sigic The operating keyboard is comprised of a two line LCD display various buttons and two Impression Controls which consist of two potentiometer knobs that control the crash strength of the numbering head and can be adjusted to best suit the requirements of the job For example you may require stronger crash numbering for carbonless sets than for single sheet bond paper This adjustment can be done while the machine is stopped or running see Figure 5 The four buttons under the LCD display will perform whatever function is shown directly above them on the bottom line of the LCD display They may not always be active this is the case for the other buttons as well Three specific function buttons SET UP BAT REP
36. or adjustment screws Lastly the changeover pawls must be parallel to each other Repeat Selector Repeat Action Ratchet Wheels 3x 2x amp 4x Retaining Comb Spring Pawlis Figure D Numbering Head Bottom View of Wheels amp Repeat Selector 31 32
37. ou will now be in the Run Mode When the machine is first turned on it defaults to Program 01 PGMO01 which is shown on the menu Pressing the START button will automatically begin Program 01 The main operating menu will change as the machine is running Page 8 The Run Mode menu looks like this DISPLAY PERF SHIELD RED ON PERF SHIELD OPEN WILL EXIT TO Mode Idle IMPRESSION 1 SOL CH1 ADJUY PULSE WIDTH S S S S IMPRESSIO SOL CH2 ADJUST PULSE WIDTH DISPLAY FUNCTIONS DISPLAY ssssss motor speed bar graph PGMxxx solenoid program in RAM cecece paper count decrement motor speed increment motor speed HALT motor emergency stop exit to Mode Idle aaa CLR gt clear paper count normally aaa BAT gt Display current batch size when batch mode is enabled KEYPAD FUNCTIONS STOP START MOTOR EMERGENCY STOP Exit to Mode Idle DECREMENT MOTOR SPEED INCREMENT MOTOR SPEED MOTOR EMERGENCY STOP Exit to Mode Idle MOTOR EMERGENCY STOP Exit to Mode Idle MOTOR EMERGENCY STOP Exit to Mode Idle MOTOR EMERGENCY STOP Exit to Mode Idle Page 9 PHOTOCELL GRN ON NO PAPER c cyc ety Prem EE ele PY TY ET H T PAH eee IF BATCH SIZE IS ZERO CLEAR PAPER COUNT ELSE DISPLAY BATCH SIZE IF BATCH SIZE IS ZERO MOTOR EMERGENCY STOP Exit to Mode Idle ELSE DISPLAY BATCH SIZE Complete numbering Eject current sheet Stop motor
38. ring head mount block just above the numbering head The numbering head will then be free to rotate to the desired orientation When satisfied be sure that the head has been returned to the print position and all knobs have been tightened Once you have the numbering head in the correct physical position program the job It is advised that you run a few test sheets to check the strength and quality of the crash impression 4 9 Setting Impression Control After setting up the machine and then programming a job Section 3 4 test sheets will have to be run to verify you are getting the correct impression in other words number sequence crash strength level impression etc The Impression Control Dials located on the control panel regulate the strength of the crash Simply turn the dial clockwise if more impression is required for multi part carbonless work Check the bottom carbonless copies of the form to see if the impression strength is adequate If the maximum setting is not adequate contact your dealer Reminder Carbonless impressions are created as a development process similar to developing a photograph The numbering image will continue to darken for a full twenty four hours but will reach about 80 of its full colour in about twenty minutes Ink chemistry offset powder and a number of other factors can affect both the time and the extent of the image Your fresh impressions will be lighter than you want but trust them to dar
39. rtant Remove the numbering head from the machine Pressing down on the numbering head shaft you will see the numbering head frame slide down the print head frame While this happens the ink pad holder mount bracket will swing away exposing the numbering wheels see Figure D The numbering wheels and repeat action ratchet wheels are mounted on a keyed shaft inside the numbering head frame The wheels are then held in place and refrained from spinning by the retaining pawls which are forced to the numbering wheel flats by the comb spring The retaining pawls must be aligned with the flats of the numbering wheels or what looks like in between the numbering wheels The comb spring must also apply a constant pressure against the retaining pawls Consequently this alignment not in effect is that the numbering wheels may spin freely causing partial impression or random numbering sequences 30 Like the retaining pawls the changeover pawls of the repeat selector must also be aligned to the flats of the numbering wheels When an impression is made the numbering wheel frame is propelled down the print head frame The ink pad holder mount bracket swings away the repeat selector is pushed back from the numbering wheels and the numbering wheels are then exposed to make their impression on the stock After reaching the bottom of its stroke the numbering wheel frame then returns to the top position As this happens the repeat selector s changeover pawls
40. ted only The 6th or 7th digit must be changed manually Also available are letter prefix wheels A J K R S Z and a u prefix wheel Modifications are possible with new numbering head orders or by special order The numbering heads also have a repeat function The repeat selector c cw see Figure 4 allows a number to be Locking repeated from one to four times By Busing A Repeat i Tab leaving the repeat selector in the 0 Repeat em a position the number will not change a ee when the head returns to the print ae position Using the 0 position prevents you from having to re set the starting number when you are programming a new job this will be discussed later Position 1 changes the number consecutively with each Une Holder Mouni Bracket stroke and positions 2 3 and 4 Figure 4 Numbering Heads repeat the number 2 3 or 4 times respectively The repeat functions are achieved by a mechanical ratchet action in the numbering head When trying to use these functions you may have to cycle the numbering head manually in order to match the number of repeats on a page to the number positions on a page 2 4 Optional Conveyor Outfeed Plate The conveyor outfeed plate sits in the machine in the same fashion as the exit tray Make sure that the spur gears mesh and do not force the conveyor outfeed plate into position The pile tray is mounted on the end of the conveyor outfeed plate with two Phillips screws and acts as a backst
41. utton again to toggle off the hit otherwise continue moving up or down the sheet the hit is automatically saved This procedure can be repeated until the number is in the correct location The page can be stopped a maximum of 15 times where you may program head 1 or head 2 or both heads to fire Once all numbers desired have been programmed simply press the ACC button and the sheet will be discharged from the machine The next sheet will be forwarded to step 5 if there is another sheet already in the feed tray or you will be instructed to INSERT PAPER PRESS START The LCD display will return to Idle Mode and you are set to run the job Simply press the START button to begin Page 12 3 5 The Batch Function Pressing the BAT key before running a program will enter the batch menu FUNCTION 1 Allows user to set or clear the batch size max batch size 999999 2 Sets a new batch size by pressing lt ACC gt The paper count and batch quantity are reset to 0 DISPLAY PERF SHIELD RED PHOTOCELL GRN IMPRESSION 1 ON PERF SHIELD OPEN ON NO PAPER NO FUNCTION IMPRESSIO NO FUNCTION DISPLAY FUNCTIONS DISPLAY XXXXX batch size SET sets the batch size CLR sets the batch size to zero At this point you may select the size of the batch desired by entering the desired batch size through the keypad Press the ACC key when the quantity desired has been chosen Press the F2 key
42. wing sheets to skew as they feed this will be seen more often with number locations closer to the non operator side furthest away from where the sheet passes the photocell if numbers occur all over the place the photocell may require readjustment it is too sensitive mis registering the lead edge of the sheet Perf score slit line With a straight edge check that the perf score slit is skewing straight If straight the stock is not feeding square the feed tray guides may need adjusting to ensure the stock enters square into the machine If the perf score slit line is not straight but is bowed or has a tail whip the rollers on the main shaft and or the exit shaft may not be evenly balanced along the shaft causing uneven pressure on one side of the stock This causes a skew and the rollers must be evenly spaced across the shaft A bowed line usually indicates the rollers on the main shaft are uneven and a tail whip usually means the rollers on the exit shaft are uneven Numbering Heads The numbering heads creating an impression are a mechanical process separate from the programming of the machine If encountering problems with the correct operation of the numbering head such as numbering wheels not turning numbers partially printing numbering wheels turning out of sequence etc the repeat selector or other components may be out of alignment refer to Figure 4 Being a mechanical process alignment of the individual parts is very impo
Download Pdf Manuals
Related Search