Home

NCA 450U Kit-AA NCA 450U Kit-AA

image

Contents

1. 4 Clip the Hogtunes front speakers Model 352F AA into each grill assembly Position your new speaker grill assembly onto the inner fairing and re attach each one using the OE screws Although a hand screwdriver is recommended for this step make sure these screws are tight Let the factory speaker wires hang for now Step 5 Remove each rear speaker grill by undoing the 4 screws on the front of the grills Carefully lift up on each speaker and take the 2 wires off by pulling one at a time from the stock speaker Put the grills fasteners and speakers aside Step 6 Step 7 Step 8 Locate the Fader No Fader switch on the side of the amplifier and make sure it is in the Fader position In this position the amplifiers front and rear channels are controlled independently by the Ultra radios built in fader If the switch is in the No Fader position all 4 channels are driven equally and although all 4 channels will play the radio s fader will not work Locate the 3 position switch on the side of the amplifier marked GAIN and make sure this switch is in the 3 position Since Ultra radios come with a fader you can use the fader control to adjust front rear balance If you were to run this amp off a 2 channel radio no fader the switch would go to the No Fader position and the gain switch would be used to adjust the volume of whatever is plugged into the rear channels The powe
2. THE MAIN WIRE HARNESS f Step 1 The power ground harness and rear harness will pass together under the inner fairing where the main wire harness passes through on the brake side of the bike Loosen the tank s chrome console and run wires up and over the gas tank but under the tank s chrome console There is a provision on the front of the tank console for wires to pass Stock Harness and Amplifiers Harnesses Passing from Fairing to Just in Front of Tank Arrow A Cable Tying the Harnesses To The Main Bike Harness Just In Front Of The Tank Arrow B Allows The Amp Harnesses To Go Up Towards The Tanks Chrome Console Easier And Makes For a Cleaner Install When correctly installed the power and ground wires are the right length to connect to the battery and if used the rear wire 8 pin harness is the right length to be zip tied to the brake side fender strut Be sure to run the 8 pin harness UNDER the air line for the brake side rear shock Please run the power harness as per the manual Sometimes people assume they know more than us and wire amplifier power to the headlight wires or other places Not only will your friends laugh at you but you will be calling us for technical support Step 2 Please save us all from the grief and phone call On the 8 pin rear harness end you will see 2 pairs of black shorter wires in a sheath and 2 pairs of black longer wires in a second sheath Put the ends of the shor
3. Amplifier s Serial Here Hogtunes speakers are warranted for a period of 20 years The NCA 450 AA Amplifier is warranted for 3 years from original purchase date Proof of purchase is required for all warranty claims The warranty applies to the original retail customer and is not transferable Please contact Hogtunes for all warranty claims Products found to be defective during the warranty period will be repaired or replaced with a product deemed to be equivalent at Hogtunes sole discretion Hogtunes complete warranty policy is available on our website at www hogtunes com warranty html What Is Not Covered 1 Any expense related to the removal or re installation of Hogtunes products 2 Repairs to these products performed by anyone other than Hogtunes 3 Subsequent damage to any other components A Any product purchased from a non authorized Hogtunes dealer 5 Damage to Hogtunes products due to an accident or collision 6 Hogtunes Amplifiers with broken or removed warranty void stickers 7 Damage due to water from custom installations 8 Damage from incorrect installation improper use abuse or modifications 9 Damage to inbound product due to improper packing Note The NCA 450 AA amplifier has low level input that is not used in this install assuming the bike has a factory radio The low level in can be used if an aftermarket car stereo is on the bike The amp s low level input is NOT an
4. Audio Solutions For The Great American Cruiser odel 352F AA Gen Ill e 5 25 e 2 Ohm Vg Front Speaker SSS Dena amp Engineered Canada 450U KIT AA High Performance Front amp Rear Speaker Kit with 200 Watt Amplifier FOR USE ON 1998 2013 ULTRA CLASSIC amp TRI GLIDE MODELS INSTALLATION MANUAL Thank you for choosing the Hogtunes NCA 450U KIT AA Since positive word of mouth is the best way to grow our business we want your new system to work as well as it was designed to If you have any questions or concerns we are here fo help Email info hogtunes com Tel 705 719 6361 If you still need help please consider a professional installation by your motorcycle dealer IMPORTANT The NCA 450 AA amplifier can not be used if any factory amplifier is already on the bike Please call us if you have any questions We will most likely have a simple solution for you GETTING STARTED Step 1 Remove the seat and both wires and from the battery Step 2 Remove the outer fairing headlamp assembly Refer to a service manual if you need help with this Note Placing a towel on the front fender can help prevent scratches or dings from dropped tools or fasteners etc Step 3 Take the 2 wires off each front speaker by gently pulling one at a time Undo the screws that attach each speaker grill assembly to the inner fairing and remove Gently pull the stock speaker out of each grill assembly Step
5. extra Auxiliary Input Please call or email us for more information TECHNICAL SPECIFICATIONS Hogtunes NCA 450 AA Amplifier Actual RMS Power at 2 Ohms 50 watts x 4 Freq Response cseeeeeeeeeerees 30hz 25khz Fuse at AMP wcsehssaononemnsientacesvess 30 amp Hogtunes 352F AA Front Speakers Power Handling ossessi 100 RMS 150 Peak Frequency Response n 55hz 25Khz Sensitivity e er eere 92 db 1watt 1 meter Nominal Impedance 6 2 0 Ohms Cool Factor nosses EXTREME Hogtunes 352R AA Rear Speakers Power Handling eeeereees 100 RMS 150 Peak Frequency Response n se 55hz 25Khz Sensitivity eessen 91 dB 1watt 1meter Nominal Impedance 6 2 0 Ohms Cool Factor sesshevceitesesescessectece Oh Baby Harley Davidson Electra Glide Road Glide Street Glide Ultra Classic Tri Glide CVO Screamin Eagle and Tour Pak are Trademarks and or Registered Trademarks of Harley Davidson Inc Milwaukee Wisconsin USA and if Used or Implied are for Reference Only There is No Affiliation Between Harley Davidson Inc and Hogtunes Inc 11 Any audio system can be a distraction to the rider and or passenger Please use caution when playing your stereo ESPECIALLY IN TRAFFIC www hogtunes com
6. ng and remove the bolts closest to you The amp will clip in to the back bolts and the bolts removed will go back in over the plates to secure the amp Re tighten all 4 bolts to factory specs Install the module shelf as shown noting that the stove bolt heads must be positioned as shown Your module s will screw into the shelf using the factory screw s you removed from the back of the radio 3 WIRING THE AMPLIFIER Step 1 Step 2 With amplifier in place take the yellow black wires on the input connector of the amplifier and plug them into the front factory speaker wires on the clutch side of the bike They will only go in one way Take the brown black wires on the front out connector and plug them into the front clutch side speaker They will only go in one way Take the green black wires on the input connector and plug them into the front factory speaker wires on the brake side of the bike Take the blue black on the front out plug and plug them into the brake side front speaker Again these will only go on one way The orange wire is the remote turn on lead and tells the amp to turn on whenever it sees 12v 5 amp min Unplug the center wire on the cigarette lighter Plug the orange lead from the amplifier directly onto the lighter using the female connector Plug the factory lighter wire to the male take off connector which is part of the amps orange turn on lead 4 ROUTING
7. r harness ends in a black plug with 1 larger 1Oawg red wire 1 larger 1Oawg black wire and 1 smaller orange wire Locate this and plug it into the matching black pigtail on the amplifier The input harness has a smaller black 8 pin plug with smaller gauge wire Plug this into the black pigtail socket on the amplifier marked hi level input Locate the 4 pin black plug with black brown and black blue wires This will plug into the front out on the amp which is a pigtai ending with a 4 pin black socket l Note There is a pigtail ending with a blue socket labeled bypass out This carries the radios built in power front channels only and although not used in this kit it is there for plug and play future system expansion The amplifier mounts inside the fairing over the radio using the side plates shown below The side plates are attached to the side of the amplifier by removing 4 screws on each side of the amp positioning the plates as shown below and re installing the screws into the amp Factory CB XM and other similar modules are mounted on top of the radio and secured with a screw that goes into the back of the radio Remove the screw and let the module s hang for now Do not install the module shelf yet Each side of the radio has 2 large allen head bolts that secure the radio into the fairing You will loosen the bolts on each side that are farthest away from you closest to the inner fairi
8. ring and everything needed to complete the job You can learn more by visiting http www hogtunes com products tweeters hf 1 html HOGTUNES SYSTEM UPGRADE 2 A As per the manual the amp powers the front speakers and tweeter pod if present and rear speakers In this upgrade the rear speakers will be run off the radios built in power The front channels of the amp will power the front speakers and the rear channels of the amp will be used to power 692 2 Lid 6x9 lid speakers or FL7W 7 woofers for your fairing lower glove boxes All bolt in all plug and play If you want to add a second amp later on we make it easy by offering the parts you need a la carte HOGTUNES saddle speakers or 7 fairing lower glove box woofers SYSTEM UPGRADE 3 A This system has the supplied 4 channel amp continue to power the fronts and rears and tweeter pod if present buts adds a Hogtunes REV 200 AA amplifier to power a set of Hogtunes 692 2 Lid saddlebag lid speakers or a set of FL 7W 7 woofers for the fairing lower glove boxes This can be done at any time all bolt in amp all plug and play Hogtunes 2CHSP mounting plate is required to bolt the REV 200 AA into your fairing Use supplied blue plug send signal from expan sion port of first amp to input of second amp JOSUNE saddle bag lid 6x9 speakers or 7 fairing lower glove box woofers WARRANTY INFORMATION P Please Record Your
9. s fader control is adjusting the volume between front and rear speakers If not double check the Fader No Fader switch ou Re install the seat making sure the amplifiers and connectors are positioned in such away so they will not bend or break when the riders weight is on the seat This is the best time to take a few minutes to clean up the wiring and secure using supplied zip ties Before re installing outer fairing turn front wheel to each extreme side making sure any wiring is not impeding the steering of the motorcycle Failure to do so can result in serious injury or death Adjusting the Bass and Treble The way the system sounds sitting still or at a stop light will be RADICALLY different from how it sounds at speed Your able to use the radios controls to adjust the sound but please do so carefully when riding Re install the fairing and your system is now ready to enjoy SYSTEM UPGRADE 1 Hogtunes HF 1 tweeter pod for 1998 2013 bikes not only looks great it s easy to install and brings ANY audio system to the next level Adding these tweeters to any system fixes the inherent audio issues created by the stock speaker locations and will give much better clarity especially at speed Out of the box HF 1 matches the factory satin black perfectly but also comes apart easily and can be painted to match any custom inner fairings HF 1 comes with plug and play wi
10. ter wires into the brake side rear speaker box These wires will enter where the factory wires enter the rear speaker box Plug the factory rear speaker wires into the male wires of the amp harness noting they will only go on one way Note The factory female rear speaker connectors are non insulated Once the factory female rear speaker connectors are plugged into the Hogtunes male connectors wrap each connection with electrical tape to prevent the positive and negatives from touching each other Take a Hogtunes rear speaker model 352R AA and plug the female connectors of the amp harness into the speaker They will only go one way Repeat this step using the longer wires on the clutch side of the bike 5 Step 3 Once you are confident the wires are correctly attached to the rear speakers sit them in place put the grills back on and secure the speakers by reinstalling the 4 screws on each grill Attach the amps red wire to the positive battery terminal and the amps black wire to the negative battery terminal The factory battery wires are also re installed at this point When attaching the power and ground wires it is always a good practice to do the negative first When the positive connector touches the battery some sparking is normal This is a function of the capacitors in the amplifier charging up Step 4 Turn the stereo on and at low volume test to make sure all 4 speakers are working Make sure the radio

Download Pdf Manuals

image

Related Search

Related Contents

Aurora User Manual Issue 6 Revision 1    BKVD-179 BRD-103    消防用設備点検等業務仕様書 1    Network Computing Devices LSQ-40L User's Manual  Manuale d`uso - Cellulari per Anziani e Telefoni Amplificati  Banshee BN27-40K - User Manual  QUICK START GUIDE Ver.10.309  

Copyright © All rights reserved.
Failed to retrieve file