Bunn Single Satellite User Manual
Contents
1. Bunn Accordingly statements by such individuals whether oral or written do not constitute warranties and should not be relied upon The Buyer shall give Bunn prompt notice of any claim to be made under this warranty by telephone at 217 529 6601 or by writing to Post Office Box 3227 Springfield Illinois 62708 3227 If requested by Bunn the Buyer Shall ship the defective equipment prepaid to an authorized Bunn service location If Bunn determines in its sole discretion that the equipment does not conform to the warranty Bunn shall repair the equipment with no charge for parts during the one year warranty period and no charge for labor for the first 90 days of the warranty period If Bunn determines that repair is not feasible Bunn shall at its sole option replace the equipment or refund the purchase price for the equipment THE BUYER S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS EQUIPMENT WHETHER DERIVED FROM WARRANTY OR OTHERWISE SHALL BE LIMITED AS SPECIFIED HEREIN TO REPAIR OR AT BUNN S SOLE OPTION REPLACEMENT OR REFUND Bunn shall not be liable for any other damage or loss including but not limited to lost profits lost sales loss of use of equipment claims of Buyer s customers cost of capital cost of down time cost of substitute equipment facilities or services or any other special incidental or consequential damages USER NOTICES The notices on this brewer should be kept2. WHIBLU_y RED SAFETY SW i O OPTIONAL 3 SET SELECTOR SWITCH SHOWN BER WITH GRINDER INTERFACE OPTION i GRY ile i FRACTIONAL VABATCH i p YHIWIO i 1 2 BATCH BREW op i CONNEC 2 3 BATCH TIMER 5 p ORA i AS REQUIRED 3H WHI GRN i FULL BATCH E 40 NO CONNECTION PN BATCH COMMON YEL El BYPASS T ii WHI GRN 40 E ici 30 IR GRINDER INTERFACE igi 2 CONNECTOR 200 OR 240 VOLTS AC 2 WIRE Page 6 Page
3. 2 wire grounded ser amp models require 2 wire vice rated 120 volts ac 20 amp grounded service rated 200 volts ac single phase 60 Hz _ Requires 3 wire grounded ser 99 amp single phase 50 Hz vice rated 120 208 volts or 120 240 volts ac 20 amp single phase 60 Hz Page 3 Electrical Hook Up CAUTION Improper electrical installation will damage electronic components 1 An electrician must provide electrical service as specified 2 Using a voltmeter check the voltage and color coding of each conductor at the electrical source 3 Remove the front panel beneath the sprayhead Models with electronic control assemblies Place the tank heater switch at the top of the control assembly in the OFF position Models with electromechanical thermostats Rotate the control thermostat knob fully counterclockwise to the OFF position 4 Feed the cord through the strain relief and connect it to the terminal block 5 Connectthe brewerto the power source and verify the voltage atthe terminal block before proceeding Replace the front panel 6 If plumbing is to be hooked up later be sure the brewer is disconnected from the power source If plumbing has been hooked up the brewer is ready for Initial Set Up PLUMBING REQUIREMENTS This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi from a Y or larger supply line A shut off valve should be installed in the line befor
4. SUNN ycie OPERATING amp SERVICE MANUAL BUNN O MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD ILLINOIS 62708 3227 PHONE 217 529 6601 FAX 217 529 6644 10698 0000B 11 93 1993 Bunn O Matic Corporation INTRODUCTION This equipment will brew a half gallon gallon or gallon and a half batch of coffee into an awaiting server at the push of a button and includes a hot water faucet for allied beverage use The brewer is specifically designed for use with a BUNNY 1 5GPR server It is only for indoor use on a sturdy counter or shelf WARRANTY Bunn 0 Matic Corp Bunn warrants the equipment manufactured by it to be commercially free from defects in material and workmanship existing at the time of manufacture and appearing within one year from the date of installation This warranty does not apply to any equipment component or part that was not manufactured by Bunn or that in Bunn s judgement has been affected by misuse neglect alteration improper installation or operation improper maintenance or repair damage or casualty THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY WRITTEN OR ORAL EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE The agents dealers or employees of Bunn are not authorized to make modifications to this warranty or to make additional warranties that are binding on
5. TCH SHOWN WITH GRINDER INTERFACE OPTION GRY 100W WARMER RED 1 I 1 4 BATCH H FRACTIONAL cE 10 BATCHES i BREW 2 fi 2 3 BATCH i A REQUIRED i 3 FULL BATCH i ai NO CONNECTION PNK O Sardi Commot 5 OPTIONAL WATER N BYPASS 501 619 WHI VIO GRINDER INTERFACE Sn so omrma 200 OR 240 VOLTS N 2 WIRE L1 4 L1 SCHEMATIC WIRING DIAGRAM SINGLE BREWER ECA GRN TANK HEATER LIMIT 1800W 120V 3700W 208V FR THERMOSTAT x READY __ E E PIN 20 L E D i Fe RED 208 08 ELLAS Y a WHI 220 D ELECTRONIC GRN WHI YEL CONTROL WHI BLU WHI SAFETY SW BLK RED RED BLK OPTIONAL 3 SET SELECTOR SWITCH SHOWN WITH GRINDER INTERFACE OPTION EN dere WHI VIO 100W WARMER WHI 1 3 BATCH d BATCHES 1 2 BATCH on A FULL BATCH c WHI GRN 3 4BATCH NO CONNECTION PNK BATCH COMMO WHI GRN INTERFACE AUXILIABY OUTLET 2 CONNECTOR E H WHI i GREEN E 200 WATT MAXIMUM 120 VOLTS 2 WIRE 120 208 VOLTS AC OR 120 240 VOLTS AC 3 WIRE SCHEMATIC WIRING DIAGRAM SINGLE A amp B BREWER ECA GRNYEL L2 LIMIT TANK HEATER THERMOSTAT an BLK 12 je BLK 12 3000 240V BLU 12 AN 2 TAN W ee _ BLU e of VHUBRN ER LO w PIN 20 ot RED Pa MOD es au ELECTRONIC WHI YEL CONTROL
6. accordance with the coffee brewing instructions OPERATING CONTROLS Selector Switch Placing the switch in the Gal 1 Gal or 1 Gal position selects the amount of coffee to be brewed in Subsequent brew cycles Repositioning this switch after a brew cycle has been initiated does not change the brew batch in progress On Warmer Switch Placing the switch in the unlighted lower position cuts power to the brew station warmer and stops brewing stopping a brew cycle after it has been started will not stop the flow of water from the funnel Placing the switch in the lighted upper position supplies power to the brew station warmer and enables the brew circuit Start Momentarily pressing and releasing this switch starts a brew cycle when the On Warmer switch is in the lighted upper position NOTE The On Warmer switch must be in the lighted upper position to initiate and complete a brew cycle COFFEE BREWING 1 Select the desired batch size Insert a BUNNE filter into the funnel Pour the proper amount of fresh coffee into the filter and level the bed of grounds by gently shaking Slide the funnel into the funnel rails Place an empty server under the funnel Place the On Warmer switch in the lighted upper position Momentarily press and release the start switch When brewing is completed simply discard the grounds and filter CLEANING 1 The use of a damp cloth rinsed in any mild non abrasive liquid detergent is recommende
7. d for cleaning all surfaces on Bunn O Matic equipment 2 Check and clean the sprayhead The sprayhead holes must always remain open NOTE In hard water areas this may need to be done daily It will help prevent liming problems in the brewer and takes less than a minute Page 5 SCHEMATIC WIRING DIAGRAM SINGLE BREWER L1 L2 N GRN TANK HEATER 1800W 120V 3700W 208V RED 12 208 OR 240V 4000W 240V ig BLIR 4 N O READY INDICATOR N O LIMIT THERMOSTAT SAFETY SW SW THERMOSTAT K je e VIO RED RED BLK WHI WHI WHI BLK OPTIONAL 3 SET SELECTOR SWITCH SHOWN WITH GRINDER INTERFACE OPTION 1 4 BATCH i FRACTIONAL VS BATCH 10 12 BATCH i BREW of 2 3 BATCH i P AS REQUIRED i TIMER SE FULL BATCH i at NO CONNECTION PN BATCH COMMOS 5 OPTIONAL WATER BYPASS SOL o omrmo INTERFACE AUXILIARY OUTLET isi 2 CONNECTOR j WHI w E GREEN i e 200 WATT MAXIMUM 120 VOLTS AC 2 WIRE N 120 208 VOLTS AC OR 120 240 VOLTS AC 3 WIRE SCHEMATIC WIRING DIAGRAM SINGLE A amp B BREWER Li L2 GRN YEL TANK HEATER 3700W 200V BLK 12 BLK 12 3300W 240 RED 12 RED 12 Ki N O READY INDICATOR N 0 LIMIT THERMOSTAT SAFETY SW K je el VIO RED RED BLK RED E ae oat BLU RED 1 so i LEVEL 2H RED BLK BOARD 35 20 al PROBE OPTIONAL 3 SET SELECTOR SWI
8. e the brewer Install a regulator the line when pressure is greater than 90 psi to reduce it to 50 psi The water inlet fitting is 4 flare NOTE Bunn O Matic recommends 1 4 copper tubing for installations of less than 25 feet and for more than 25 feet from the Y water supply line A tight coil of copper tubing in the water line will facilitate moving the brewer to clean the countertop Bunn O Matic does not recommend the use of a saddle valve to install the brewer The size and shape of the hole made in the supply line by this type of device may restrict water flow This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials and Code Administrators International Inc BOCA and the Food Service Sanitation Manual of the Food and Drug Administration FDA Plumbing Hook Up 1 Attach the flare fitting from the short piece of tubing on the flow control supplied to the water inlet fitting on the bottom of the brewer 2 Flush the water line and securely attach it to the flare fitting on the strainer 3 Turn on the water supply INITIAL SET UP CAUTION The brewer must be disconnected from the power source throughout the initial set up except when specified in the instructions 1 Remove the front panel beneath the sprayhead Models with electronic control assemblies Place the tank heater switch at the top of the control assembly in the position Models with e
9. in good condition Replace unreadable or damaged labels A CAUTION DISCARD DECANTER AF CRACKED SCRATCHED BOILED DRY HEATED WHEN EMPTY USED ON HIGH 00658 0000 FUNNEL CONTENTS or EXPOSED ELECTRIC ARE HOT ELEMENTS FAILURE TO COMPLY RISKS INJURY 1985 BUNN O MATIC CORPORATION 12364 0000 CAUTION WARMERS AND SURFACES ARE HOT USER NOTICES cont AWARNING 0 Fill water tank before turning on thermostat or connecting appliance to power source Use only on a properly protected circuit capable of the rated load Electrically ground the chassis Follow national local electrical codes Do not use near combustibles FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE FIRE OR SHOCK HAZARD READ THE ENTIRE OPERATING MANUAL INCLUDING THE LIMIT OF WARRANTY AND LIABILITY BEFORE BUYING OR USING THIS PRODUCT THIS APPLIANCE IS HEATED WHENEVER CONNECTED TO A POWER SOURCE 831A 5 88 1988 Bunn O Matic Corporation 00831 0000 This equipment is to be installed to comply with the Basic Plumbing Code of the Building Officials and Code 00656 0000 Administrators International Inc BOCA and the Food Service Sanitation Manual of the Food and Drug Administration FDA ELECTRICAL REQUIREMENTS CAUTION The brewer must be disconnected from the power source until specified in nitial Set Up NEUTRAL 120V A C y A 208 or 240V A C Li BLACK Requires
10. lectromechanical thermostats Rotate the control thermostat knob fully counterclockwise to the OFF position 2 Connect the brewer to the power source Water will begin flowing into the tank 3 When water stops flowing into the tank remove the front panel and proceed as directed Models with electronic control assemblies Place the tank heater switch atthe top ofthe control assembly in the ON position and replace the front panel Models with electromechanical thermostats Rotate the control thermostat knob fully clockwise to the ON position and replace the front panel ilk Page 4 SET UP cont Wait approximately twenty minutes for the water in the tank to heat to the proper temperature 4 Place an empty server beneath the brew station Place the Selector switch in the one gallon position the On Warmer switch in the upper position and initiate a brew cycle 6 Place the On Warmer switch in the lower OFF position after water has stopped flowing from the funnel and check the water volume in the server It should be 128 ounces 7 If not disconnect the brewer from the power source remove the front panel and adjust the brew timer dial up or down as required Replace the front panel connectthe brewer to the power source allow the water to reheat start and measure another brew cycle 8 Repeat step until the proper water volume is achieved 9 The brewer is now ready for use in
Download Pdf Manuals
Related Search